Non-linear buffeting response analysis of long-span suspension bridges with central buckle

The rigid central buckle employed in the Runyang Suspension Bridge (RSB) was the first time it was used in a suspension bridge in China. By using a spectral representation method and FFT technique combined with measured data,a 3D fluctuating wind field considering the tower wind effect is simulated. A novel FE model for buffeting analysis is then presented,in which a specific user-defined Matrix27 element in ANSYS is employed to simulate the aeroelastic forces and its stiffness or damping matrices are parameterized by wind velocity and vibration frequency. A nonlinear time history analysis is carried out to study the influence of the rigid central buckle on the wind-induced buffeting response of a long-span suspension bridge. The results can be used as a reference for wind resistance design of long-span suspension bridges with a rigid central buckle in the future.

Structural condition assessment of long-span suspension bridges using long-term monitoring data

这份报纸集中于用监视系统的结构的健康测量的长期的监视数据开发一种联机结构的条件评价技术。为 Runyang 暂停桥的频率温度和横梁结束排水量温度的季节的关联首先被执行。然后，用一个六顺序的多项式的一种统计建模技术进一步被使用提出频率温度和排水量温度，测量频率和排水量的反常变化用吝啬的价值控制图表从被检测的关联。分析结果证明更高的颤动模式和排水量的形式的频率与环境温度和建议方法展览有显著季节的关联为检测形式的频率和排水量的微导致损坏的变化的一个好能力。结果证明建议方法能有效地从频率和排水量时间系列消除温度复杂并发症并且很好适合长跨度的暂停桥监视的联机状况。监视的关键词结构的健康 - 形式的频率 - 横梁结束排水量 - 温度 - 季节的关联 - 暂停桥牌旁边支持了：在资助号码下面的中国的国家自然科学基础 50725828 与号码 50808041；不到资助号码 200802861011 的中国的教育部的博士节目基础；东南大学在下面的研究生院的科学研究基础资助没有。

Three-dimensional nonlinear flutter analysis of long-span suspension bridges during erection

In this work, the aerodynamic stability of the Yichang Suspension Bridge over Yangtze River during erection was determined by three-dimensional nonlinear flutter analysis, in which the nonlinearities of structural dynamic characteristics and aeroelastic forces caused by large deformation are fully considered. An interesting resuh obtained was that the bridge was more stable when the stiffening girders were erected in a non-symmetrical manner as opposed to the traditional symmetrical erection schedule. It was also found that the severe decrease in the aerodynamic stability was due to the nonlinear effects. Therefore, the nonlinear factors should be considered accurately in aerodynamic stability analysis of long-span suspension bridges during erection.

Structural health monitoring of long-span suspension bridges using wavelet packet analysis

During the service life of civil engineering structures such as long-span bridges, local damage at key positions may continually accumulate, and may finally result in their sudden failure. One core issue of global vibration-based health monitoring methods is to seek some damage indices that are sensitive to structural damage. This paper proposes an online structural health monitoring method for long-span suspension bridges using wavelet packet transform (WPT). The WPT- based method is based on the energy variations of structural ambient vibration responses decomposed using wavelet packet analysis. The main feature of this method is that the proposed wavelet packet energy spectrum (WPES) has the ability to detect structural damage from ambient vibration tests of a long-span suspension bridge. As an example application, the WPES-based health monitoring system is used on the Runyang Suspension Bridge under daily environmental conditions. The analysis reveals that changes in environmental temperature have a long-term influence on the WPES, while the effect of traffic loadings on the measured WPES of the bridge presents instantaneous changes because of the nonstationary properties of the loadings. The condition indication indices VD reflect the influences of environmental temperature on the dynamic properties of the Runyang Suspension Bridge. The field tests demonstrate that the proposed WPES-based condition indication index VD is a good candidate index for health monitoring of long-span suspension bridges under ambient excitations.

Advanced aerostatic analysis of long-span suspension bridges

As the span length of suspension bridges increases, the diameter of cables and thus the wind load acting on them, the nonlinear wind-structure interaction and the wind speed spatial non-uniformity all increase consequently, which may have un-negligible influence on the aerostatic behavior of long-span suspension bridges. In this work, a method of advanced aerostatic analysis is presented firstly by considering the geometric nonlinearity, the nonlinear wind-structures and wind speed spatial non-uniformity. By taking the Runyang Bridge over the Yangtze River as example, effects of the nonlinear wind-structure inter-action, wind speed spatial non-uniformity, and the cable’s wind load on the aerostatic behavior of the bridge are investigated analytically. The results showed that these factors all have important influence on the aerostatic behavior, and should be considered in the aerostatic analysis of long and particularly super long-span suspension bridges.

Defect Inspection Technology for Steel Truss Suspension Bridges

Steel truss suspension bridges are prone to developing defects after prolonged use.These defects may include corrosion of the main cable or the steel truss.To ensure the normal and safe functioning of the suspension bridge,it is necessary to inspect for defects promptly,understand the cause of the defect,and locate it through the use of inspection technology.By promptly addressing defects,the suspension bridge’s safety can be ensured.The author has analyzed the common defects and causes of steel truss suspension bridges and proposed specific inspection technologies.This research is intended to aid in the timely discovery of steel truss suspension bridge defects.

Deformation monitoring of long-span railway bridges based on SBAS-InSAR technology

The deformation monitoring of long-span railway bridges is significant to ensure the safety of human life and property.The interferometric synthetic aperture radar(In SAR)technology has the advantage of high accuracy in bridge deformation monitoring.This study monitored the deformation of the Ganjiang Super Bridge based on the small baseline subsets(SBAS)In SAR technology and Sentinel-1A data.We analyzed the deformation results combined with bridge structure,temperature,and riverbed sediment scouring.The results are as follows:(1)The Ganjiang Super Bridge area is stable overall,with deformation rates ranging from-15.6 mm/yr to 10.7 mm/yr(2)The settlement of the Ganjiang Super Bridge deck gradually increases from the bridge tower toward the main span,which conforms to the typical deformation pattern of a cable-stayed bridge.(3)The sediment scouring from the riverbed cause the serious settlement on the bridge’s east side compared with that on the west side.(4)The bridge deformation negatively correlates with temperature,with a faster settlement at a higher temperature and a slow rebound trend at a lower temperature.The study findings can provide scientific data support for the health monitoring of long-span railway bridges.

Accurate stress analysis on rigid central buckle of long-span suspension bridges based on submodel method

Runyang Suspension Bridge (RSB) with the main span of 1490 m is the longest bridge in China and the third longest one in the world. In this bridge the rigid central buckle is employed for the first time in the mid-span of the suspension bridge in China. For such a super-long-span bridge, the traditional finite element (FE) modeling technique and stress analysis methods obviously cannot satisfy the needs of conducting accurate stress analysis on the central buckle. In this paper, the submodel method is in- troduced and for the first time used in analyzing the stresses of the central buckle. After an accurate FE submodel of the central buckle was specially established according to the analysis results from the whole FE model, the connection technique between the two-scale FE models was realized and the ac- curate stresses of the central buckle under various vehicle load cases were then conducted based on the submodel method. The calculation results were testified to be accurate and reliable by the field measurements, which show the efficiency and reliability of the submodel method on analyzing the mechanical condition of the central buckle of long-span suspension bridges. Finally, the working be- havior and mechanical characteristics of the central buckle of the RSB under vehicle loads were ana- lyzed based on the calculation and measurement results. The results obtained in this paper can provide theoretic references for analyzing and designing the rigid central buckle in long-span suspension bridges in future.

Damper placement for seismic control of super-long-span suspension bridges based on the first-order optimization method

To ensure the anti-earthquake performances of super-long-span suspension bridges, effective devices should be employed to control the seismic response of key sections. In this paper, four kinds of assessment functions for seismic response control effect are formulated based on the mechanism of seismic response control with dampers and the seismic response characteristics of long-span suspension bridges. A new optimal placement method of dampers using penalty function and first-order optimization theory is then proposed. Runyang suspension bridge (RSB) with a main span of 1490 m is then taken as an example. After seismic response time-history analyses on RSB using different placements of dampers, the analysis results are optimized by employing the optimal placement method and the optimal placements of dampers with the four assessment functions are then achieved respectively. Comparison of the four optimal control effects show that different assessment functions can lead to different optimal placements when the number of dampers is certain, but all placements of dampers can reduce the seismic response of RSB significantly. The selection of assessment functions and damper optimal placement should be determined by the structural characteristics and by what is considered in the structures. Results also show that the first-order optimization is an effective method on determining the optimal placement of dampers.

Multi-type sensor placement and response reconstruction for structural health monitoring of long-span suspension bridges

This study is devoted to the experimental validation of the multi-type sensor placement and response reconstruction method for structural health monitoring of long-span suspension bridges. The method for multi-type sensor placement and response reconstruction is briefly described. A test bed, comprising of a physical model and an updated finite element(FE) model of a long-span suspension bridge is also concisely introduced. The proposed method is then applied to the test bed; the equation of motion of the test bed subject to ground motion, the objective function for sensor location optimization, the principles for mode selection and multi-type response reconstruction are established. A numerical study using the updated FE model is performed to select the sensor types,numbers, and locations. Subsequently, with the identified sensor locations and some practical considerations, fiber Bragg grating(FBG) sensors, laser displacement transducers, and accelerometers are installed on the physical bridge model. Finally, experimental investigations are conducted to validate the proposed method. The experimental results show that the reconstructed responses using the measured responses from the limited number of multitype sensors agree well with the actual bridge responses.The proposed method is validated to be feasible and effective for the monitoring of structural behavior of longspan suspension bridges.

Cable flexural rigidity influence on suspension bridges static properties

In order to figure out the cable flexural rigidity influence on suspension bridges,a contrast model experiment is made:a chain cable model with no flexural rigidity and a wire cable model with some flexural rigidity.And then,four finite element models of a same long-span suspension bridge with different cable element are set up to be analyzed.Both experimental and numerical simulation results show that,with the increase of the span and the decrease of sag-span ratio,the influence of the cable flexural rigidity is significant.The difference of nodes displacement reaches more than 10 cm in construction analysis,which will bring some trouble to the construction.And the difference of the maximum section edge normal stress may reach 15%,which may have an adverse impact onto the bridge.Therefore,considering the cable flexural rigidity is necessary on some analysis of suspension bridges.

A method for calculating strand tension in the anchor span of a suspension bridge considering the rotation of a splay saddle

This paper reports a method for strand tension in anchor spans considering rotation.A kind of co-moved coordinate system,a saddle local coordinate system,was set up.This system implemented the rotation of the splay saddle through the rotation of the coordinate system,and all calculations proceeded in this coordinate system.Considering the rotation of the anchoring surface by the rotation of the local coordinate system of the anchoring surface,the anchorage point coordinates of strands were transformed to the local sadle coordinate system.There was a two-layer iteration adopted in the calculation.In the inner iteration,the cable force at the end of the vertical bend was taken as the variable,and the ordinate of the anchorage point was taken as the target value.In the outer iteration,the vertical tangential angle at the end of the vertical bend was taken as the variable,and the ordinate of the anchorage point was taken as the target value.The method carried out the rotation of the splay saddle and anchor surface and was simple,convenient and without approximation.The effect of rotation was considered precisely;it showed stability during the process of two-layer iteration,powerful adaptation and higher efficiency and had been successfully applied in the construction control of the Wufengshan Yangtze River Bridge,the world's first kilometer-level combined highway and railway suspension bridge.

Mechanical deformation properties of Continuous Welded Rail on kilometer-span suspension bridge for high-speed railway

The complex bridge-track interaction between kilometer-span bridges and continuous Welded Rail(CWR)brings great challenges to CWR designing.Taking a suspension bridge with laying CWR as a case,the mechanical properties of CWR on the bridge are analyzed to reveal the sensitive areas of the track,and the design method of CWR and track structures on the beam ends are proposed.The results show that the unidirectional Rail Expansion Joints(REJ)need to be installed on the beam end of the kilometer-span bridge to reduce rail longitudinal force.Due to the bridge characteristics,there is no CWR fixed area on the kilometer-span bridge,and rail longitudinal force on the main span caused by bending loads needs to be concerned.The deformation of track on the beam end is complex,which is the weak area on the kilometer bridge,the large relative displacement between the stock rail of REJ and the main beam can cause poor stability of ballast bed on beam end,small resistance fasteners need to be laid on the sides of stock rail on the main beam to increase the stability of ballast and fasteners on the beam end.To improve the driving safety and comfort of beam end,the Sleeper-Supporting Apparatus(SSA)should be specially designed to ensure the uniform transition of track on beam ends.Temperature and wind loads have a significant impact on track regularity on the kilometer span bridge,the dynamic response of trains and bridges under those loads needs to be attended to.

Long-Time Behavior of Solution for Autonomous Suspension Bridge Equations with State-Dependent Delay

This work is devoted to the following suspension bridge with state-dependent delay: . The main goal of this paper is to investigate the long-time behavior of the system. Under suitable hypothesis, the quasi-stability estimates of the system are established, based on which the existence of global attractor with finite fractal dimension is obtained. Furthermore, the existence of exponential attractor is proved.

Proposing a New Model of Hangers in Pedestrian Suspension Bridges to Solve Hangers Slackness Problem

The hangers of suspension bridges can be placed in two forms: vertical or inclined form. Inclined hangers are more liable to fatigue. Vertical hangers are subjected to greater fluctuations of stress resulting from bridge wind loads. To improve aerodynamic stability, inclined hangers can be used instead of vertical ones. Some inclined hangers show considerable signs of distress and some of them show slackness due to their location against loads. In this paper a pedestrian suspension bridge with vertical hangers has been studied as a case study. Then, the same bridge has been studied with inclined hangers. To reduce internal forces, fatigue and slackness in hangers, horizontal cables have been added to inclined hangers. This modification is proposed by the present authors. The added horizontal cables transfer the tensile load from overstressed hangers to adjacent slacked hangers. Three different hanger patterns have been analyzed under nonlinear static analysis for symmetrical and nonsymmetrical live load plus dead load. Results showed that the modified hanger system had been improved considerably in comparison with vertical or inclined hangers and wherever that there is no improvement some solutions have been proposed.

Application of buckling-restrained braces in the seismic control of suspension bridges

Buckling-restrained braces(BRBs)are widely used to improve the seismic performance of buildings.This paper aims to introduce BRBs to suspension bridges and assess the seismic performance of bridges with BRBs.Taking the Dadu River Bridge as a case study,an FEA model of the bridge is established,and different seismic measures(BRBs between the deck and the tower,BRBs at the middle of the span to replace the inclined suspenders to connect the deck and the main cables,fluid viscous dampers(FVDs)between the deck and the tower,the combination of BRBs to replace the inclined suspenders as well as FVDs between the deck and the tower)are applied to the suspension bridge.The influence of the parameters of BRBs on the seismic response of the suspension bridge is studied,and the performance of the bridge with BRBs is compared with that of the bridge with FVDs.The results indicate that the use of BRBs in place of the inclined suspenders is beneficial to reduce the displacement of the deck and limit the shear force and bending moment of the tower.The seismic performance of the suspension bridge with BRBs and FVDs is better than that of the bridge with BRBs or FVDs.Therefore,the application of BRBs is a feasible method to improve the seismic performance of the suspension bridge.

Determination of reasonable finished state of self-anchored suspension bridges

A systematic and generic procedure for the determination of the reasonable finished state of self-anchored suspension bridges is proposed, the realization of which is mainly through adjustment of the hanger tensions. The initial hanger tensions are first obtained through an iterative analysis by combining the girder-tower-only finite element(FE) model with the analytical program for shape finding of the spatial cable system. These initial hanger tensions, together with the corresponding cable coordinates and internal forces, are then included into the FE model of the total bridge system, the nonlinear analysis of which involves the optimization technique. Calculations are repeated until the optimization algorithm converges to the most optimal hanger tensions(i.e. the desired reasonable finished bridge state). The "temperature rigid arm" is introduced to offset the unavoidable initial deformations of the girder and tower, which are due to the huge axial forces originated from the main cable. Moreover, by changing the stiffness coefficient K in the girder-tower-only FE model, the stiffness proportion of the main girder, the tower or the cable subsystem in the whole structural system could be adjusted according to the design intentions. The effectiveness of the proposed method is examined and demonstrated by one simple tutorial example and one self-anchored suspension bridge.

Damage alarming of long-span suspension bridge based on GPS-RTK monitoring

Structure damage identification and alarming of long-span bridge were conducted with three-dimensional dynamic displacement data collected by GPS subsystem of health monitoring system on Runyang Suspension Bridge.First,the effects of temperature on the main girder spatial position coordinates were analyzed from the transverse,longitudinal and vertical directions of bridge,and the correlation regression models were built between temperature and the position coordinates of main girder in the longitudinal and vertical directions;then the alarming indices of coordinate residuals were conducted,and the mean-value control chart was applied to making statistical pattern identification for abnormal changes of girder dynamic coordinates;and finally,the structural damage alarming method of main girder was established.Analysis results show that temperature has remarkable correlation with position coordinates in the longitudinal and vertical directions of bridge,and has weak correlation with the transverse coordinates.The 3%abnormal change of the longitudinal coordinates and 5%abnormal change of the vertical ones caused by structural damage are respectively identified by the mean-value control chart method based on GPS dynamic monitoring data and hence the structural abnormalities state identification and damage alarming for main girder of long-span suspension bridge can be realized in multiple directions.

Dynamic Analysis of Suspension Bridges and Full Scale Testing

This paper is concerned with the earthquake analysis of suspension bridges, in which the effects of large deflections are taken into account. The first part of the study deals with an iteration scheme for the nonlinear static analysis of suspension bridges by means of tangent stiffness matrices. The concept of tangent stiffness matrix is then introduced in the frequency equation governing the free vibration of the system. At any equilibrium stage, the vibrations are assumed to take place tangent to the curve representing the force-deflection characteristics of the structure. The bridge is idealized as a three dimensional lumped mass system and subjected to three orthogonal components of earthquake ground motion producing horizontal, vertical and torsional oscillations. By this means a realistic appraisal is achieved for torsional response as well as for the other types of vibration. The modal response spectrum technique is applied to evaluate the seismic loading for the combination of these vibrations. Various numerical examples are introduced in order to demonstrate the method of analysis. The procedure described enables the designer to evaluate the nonlinear dynamic response of suspension bridges in a systematic manner.