Contrasts of bimodal tropical instability waves(TIWs)-induced wind stress perturbations in the Pacific Ocean among observations,ocean models,and coupled climate models

The coupling between wind stress perturbations and sea surface temperature(SST)perturbations induced by tropical instability waves(TIWs)in the Pacific Ocean has been revealed previously and proven crucial to both the atmosphere and ocean.However,an overlooked fact by previous studies is that the loosely defined“TIWs”actually consist of two modes,including the Yanai wave-based TIW on the equator(hereafter eTIW)and the Rossby wave-based TIW off the equator(hereafter vTIW).Hence,the individual feedbacks of the wind stress to the bimodal TIWs remain unexplored.In this study,individual coupling relationships are established for both eTIW and v TIW,including the relationship between the TIW-induced SST perturbations and two components of wind stress perturbations,and the relationship between the TIW-induced wind stress perturbation divergence(curl)and the downwind(crosswind)TIW-induced SST gradients.Results show that,due to different distributions of eTIW and vTIW,the coupling strength induced by the eTIW is stronger on the equator,and that by the vTIW is stronger off the equator.The results of any of eTIW and vTIW are higher than those of the loosely defined TIWs.We further investigated how well the coupling relationships remained in several widely recognized oceanic general circulation models and fully coupled climate models.However,the coupling relationships cannot be well represented in most numerical models.Finally,we confirmed that higher resolution usually corresponds to more accurate simulation.Therefore,the coupling models established in this study are complementary to previous research and can be used to refine the oceanic and coupled climate models.

Comparisons of Wave Force Model Effects on the Structural Responses and Fatigue Loads of a Semi-Submersible Floating Wind Turbine

The selection of wave force models will significantly impact the structural responses of floating wind turbines.In this study,comparisons of wave force model effects on the structural responses and fatigue loads of a semi-submersible floating wind turbine(SFWT)were conducted.Simulations were performed by employing the Morison equation(ME)with linear or second-order wave kinematics and potential flow theory(PFT)with first-or second-order wave forces.A comparison of regular waves,irregular waves,and coupled wind/waves analyses with the experimental data showed that many of the simulation results and experimental data are relatively consistent.However,notable discrepancies are found in the response amplitude operators for platform heave,tower base bending moment,and tension in mooring lines.PFT models give more satisfactory results of heave but more significant discrepan-cies in tower base bending moment than the ME models.In irregular wave analyses,low-frequency resonances were captured by PFT models with second-order difference-frequency terms,and high-frequency resonances were captured by the ME models or PFT models with second-order sum-frequency terms.These force models capture the response frequencies but do not reasonably predict the response amplitudes.The coupled wind/waves analyses showed more satisfactory results than the wave-only analyses.However,an important detail to note is that this satisfactory result is based on the overprediction of wind-induced responses.

Simulating the evolution of focused waves by a two-layer Boussinesq-type model

Accurate simulation of the evolution of freak waves by the wave phase focusing method requires accurate linear and nonlinear properties,especially in deep-water conditions.In this paper,we analyze the ability to simulate deep-water focused waves of a two-layer Boussinesq-type(BT)model,which has been shown to have excellent linear and nonlinear performance.To further improve the numerical accuracy and stability,the internal wavegenerated method is introduced into the two-layer Boussinesq-type model.Firstly,the sensitivity of the numerical results to the grid resolution is analyzed to verify the convergence of the model;secondly,the focused wave propagating in two opposite directions is simulated to prove the symmetry of the numerical results and the feasibility of the internal wave-generated method;thirdly,the limiting focused wave condition is simulated to compare and analyze the wave surface and the horizontal velocity of the profile at the focusing position,which is in good agreement with the measured values.Meanwhile the simulation of focused waves in very deep waters agrees well with the measured values,which further demonstrates the capability of the two-layer BT model in simulating focused waves in deep waters.

Predicting hepatocellular carcinoma: A new non-invasive model based on shear wave elastography

BACKGROUND Integrating conventional ultrasound features with 2D shear wave elastography(2D-SWE)can potentially enhance preoperative hepatocellular carcinoma(HCC)predictions.AIM To develop a 2D-SWE-based predictive model for preoperative identification of HCC.METHODS A retrospective analysis of 884 patients who underwent liver resection and pathology evaluation from February 2021 to August 2023 was conducted at the Oriental Hepatobiliary Surgery Hospital.The patients were divided into the modeling group(n=720)and the control group(n=164).The study included conventional ultrasound,2D-SWE,and preoperative laboratory tests.Multiple logistic regression was used to identify independent predictive factors for RESULTS In the modeling group analysis,maximal elasticity(Emax)of tumors and their peripheries,platelet count,cirrhosis,and blood flow were independent risk indicators for malignancies.These factors yielded an area under the curve of 0.77(95%confidence interval:0.73-0.81)with 84%sensitivity and 61%specificity.The model demonstrated good calibration in both the construction and validation cohorts,as shown by the calibration graph and Hosmer-Lemeshow test(P=0.683 and P=0.658,respectively).Additionally,the mean elasticity(Emean)of the tumor periphery was identified as a risk factor for microvascular invasion(MVI)in malignant liver tumors(P=0.003).Patients receiving antiviral treatment differed significantly in platelet count(P=0.002),Emax of tumors(P=0.033),Emean of tumors(P=0.042),Emax at tumor periphery(P<0.001),and Emean at tumor periphery(P=0.003).CONCLUSION 2D-SWE’s hardness value serves as a valuable marker for enhancing the preoperative diagnosis of malignant liver lesions,correlating significantly with MVI and antiviral treatment efficacy.

Evaluation of Nonbreaking Wave-Induced Mixing Parameterization Schemes Based on a One-Dimensional Ocean Model

Surface waves have a considerable effect on vertical mixing in the upper ocean.In the past two decades,the vertical mixing induced through nonbreaking surface waves has been used in ocean and climate models to improve the simulation of the upper ocean.Thus far,several nonbreaking wave-induced mixing parameterization schemes have been proposed;however,no quantitative comparison has been performed among them.In this paper,a one-dimensional ocean model was used to compare the performances of five schemes,including those of Qiao et al.(Q),Hu and Wang(HW),Huang and Qiao(HQ),Pleskachevsky et al.(P),and Ghantous and Babanin(GB).Similar to previous studies,all of these schemes can decrease the simulated sea surface temperature(SST),increase the subsurface temperature,and deepen the mixed layer,thereby alleviating the common thermal deviation problem of the ocean model for upper ocean simulation.Among these schemes,the HQ scheme exhibited the weakest wave-induced mixing effect,and the HW scheme exhibited the strongest effect;the other three schemes exhibited roughly the same effect.In particular,the Q and P schemes exhibited nearly the same effect.In the simulation based on observations from the Ocean Weather Station Papa,the HQ scheme exhibited the best performance,followed by the Q scheme.In the experiment with the HQ scheme,the root-mean-square deviation of the simulated SST from the observations was 0.43℃,and the mixed layer depth(MLD)was 2.0 m.As a contrast,the deviations of the SST and MLD reached 1.25℃ and 8.4 m,respectively,in the experiment without wave-induced mixing.

Electrostatic Attraction and Repulsion Explained and Modelled Mathematically Using Classical Physics—A Detailed Mechanism Based on Particle Wave Functions

The phenomenon of electrical attraction and repulsion between charged particles is well known, and described mathematically by Coulomb’s Law, yet until now there has been no explanation for why this occurs. There has been no mechanistic explanation that reveals what causes the charged particles to accelerate, either towards or away from each other. This paper gives a detailed explanation of the phenomena of electrical attraction and repulsion based on my previous work that determined the exact wave-function solutions for both the Electron and the Positron. It is revealed that the effects are caused by wave interactions between the wave functions that result in Electromagnetic reflections of parts of the particle’s wave functions, causing a change in their momenta.

Mathematical Wave Functions and 3D Finite Element Modelling of the Electron and Positron

The wave/particle duality of particles in Physics is well known. Particles have properties that uniquely characterize them from one another, such as mass, charge and spin. Charged particles have associated Electric and Magnetic fields. Also, every moving particle has a De Broglie wavelength determined by its mass and velocity. This paper shows that all of these properties of a particle can be derived from a single wave function equation for that particle. Wave functions for the Electron and the Positron are presented and principles are provided that can be used to calculate the wave functions of all the fundamental particles in Physics. Fundamental particles such as electrons and positrons are considered to be point particles in the Standard Model of Physics and are not considered to have a structure. This paper demonstrates that they do indeed have structure and that this structure extends into the space around the particle’s center (in fact, they have infinite extent), but with rapidly diminishing energy density with the distance from that center. The particles are formed from Electromagnetic standing waves, which are stable solutions to the Schrödinger and Classical wave equations. This stable structure therefore accounts for both the wave and particle nature of these particles. In fact, all of their properties such as mass, spin and electric charge, can be accounted for from this structure. These particle properties appear to originate from a single point at the center of the wave function structure, in the same sort of way that the Shell theorem of gravity causes the gravity of a body to appear to all originate from a central point. This paper represents the first two fully characterized fundamental particles, with a complete description of their structure and properties, built up from the underlying Electromagnetic waves that comprise these and all fundamental particles.

Stress wave analysis of high-voltage pulse discharge rock fragmentation based on plasma channel impedance model

High-voltage pulse discharge(HVPD)rock fragmentation controls a plasma channel forming inside the rock by adjusting the electrical parameters,electrode type,etc.In this work,an HVPD rock fragmentation test platform was built and the test waveforms were measured.Considering the effects of temperature,channel expansion and electromagnetic radiation,the impedance model of the plasma channel in the rock was established.The parameters and initial values of the model were determined by an iterative computational process.The model calculation results can reasonably characterize the development of the plasma channel in the rock and estimate the shock wave characteristics.Based on the plasma channel impedance model,the temporal and spatial distribution characteristics of the radial stress and tangential stress in the rock were calculated,and the rock fragmentation effect of the HVPD was analyzed.

Modeling wave attenuation by vegetation with accompanying currents in SWAN

Coastal wetlands such as salt marshes and mangroves provide important protection against stormy waves.Accurate assessments of wetlands’capacity in wave attenuation are required to safely utilize their protection services.Recent studies have shown that tidal currents have a significant impact on wetlands’wave attenuation capacity,but such impact has been rarely considered in numerical models,which may lead to overestimation of wave attenuation in wetlands.This study modified the SWAN(Simulating Waves Nearshore)model to account for the effect of accompanying currents on vegetation-induced wave dissipation.Furthermore,this model was extended to include automatically derived vegetation drag coefficients,spatially varying vegetation height,and Doppler Effect in combined current-wave flows.Model evaluation against an analytical model and flume data shows that the modified model can accurately simulate wave height change in combined current-wave flows.Subsequently,we applied the new model to a mangrove wetland on Hailing Island in China with a special focus on the effect of currents on wave dissipation.It is found that the currents can either increase or decrease wave attenuation depending on the ratio of current velocity to the amplitude of the horizontal wave orbital velocity,which is in good agreement with field observations.Lastly,we used Hailing Island site as an example to simulate wave attenuation by vegetation under hypothetical storm surge conditions.Model results indicate that when currents are 0.08–0.15 m/s and the incident wave height is 0.75–0.90 m,wetlands’wave attenuation capacity can be reduced by nearly 10%compared with pure wave conditions,which provides implications for critical design conditions for coastal safety.The obtained results and the developed model are valuable for the design and implementation of wetland-based coastal defense.The code of the developed model has been made open source,in the hope to assist further research and coastal management.

Analysis of a simplification strategy in a nonhydrostatic model for surface and internal wave problems

This paper examines the simplification strategy of retaining only the nonhydrostatic effect of local acceleration in a three-dimensional fully nonhydrostatic model regarding the submesoscale wave phenomenon in the ocean.Elaborate scale analysis of the vertical component of the Reynold-averaged Navier-Stokes(RANS)equation was performed,confirming the rationalization of this simplification.Then,the simplification was implemented in a RANS equation-based nonhydrostatic model NHWAVE(nonhydrostatic WAVE)to make a simplified nonhydrostatic model.Numerical examples were taken to test its performance,including surface sinusoidal waves propagating on an idealized East China Sea topography,tidally induced internal lee waves and small-scale solitary waves.The results show that in a considerably wide range of nonlinear strengths,the simplified nonhydrostatic model can obtain similar results as those in the fully nonhydrostatic model,even for smaller-scale solitary waves.Nonlinearity influences the applicability of the simplification.The stronger the nonlinearity is,the worse the simplified model describes the nonhydrostatic phenomenon.In general,the simplified nonhydrostatic model can simulate surface waves better than internal waves.Improvement of computational efficiency in the simplified nonhydrostatic model is reasonable,reducing the central processing unit time duration in the fully nonhydrostatic model by 16.4%–20.6%.The specially designed algorithm based on the simplified nonhydrostatic equation can remarkably reduce the computational time.

Simulation of Horizontal-Two-Dimension Focused Waves Using A Two-Layer Boussinesq-Type Model

Accurate simulation of the horizontal-two-dimension(H2D)focused wave group in deep water requires high accuracy of a numerical model.The two-layer Boussinesq-type model(Liu and Fang,2016;Liu et al.,2018)with the highest spatial derivative of 2 has high accuracy in both linear and nonlinear properties.Based on the further development of the velocity equations(Liu et al.,2023),the H2D numerical model for water waves is established with the prediction-correction-iteration model in the finite difference method,and a composite fourth-order Adams-Bashforth-Moulton scheme is used for time integration.The wave generation method proposed by Hsiao et al.(2005)is applied and calibrated in this H2D model.The numerical calculations lead to the following three main conclusions:First,compared with the analytical solution of Stokes linear waves,the calculated velocity profiles show higher accuracy by using the improved velocity formulas.Second,the simulations of the focused multidirectional wave group are carried out,and good agreements are found,demonstrating that the present H2D numerical model shows high accuracy in simulating focused multidirectional wave groups,and the effectiveness of the improved velocity formulas is also validated.Furthermore,the velocity profiles throughout the computational domain at the time of maximum wave crest are given.Finally,the FFT method is used to obtain the amplitude with different frequencies for several locations,and the changes of the wavelet energy spectrum at different locations are presented for several cases.

Acoustic propagation uncertainty in internal wave environments using an ocean-acoustic joint model

An ocean-acoustic joint model is developed for research of acoustic propagation uncertainty in internal wave environments.The internal waves are numerically produced by tidal forcing over a continental slope using an ocean model.Three parameters(i.e.,internal wave,source depth,and water depth)contribute to the dynamic waveguide environments,and result in stochastic sound fields.The sensitivity of the transmission loss(TL)to environment parameters,statistical characteristics of the TL variation,and the associated physical mechanisms are investigated by the Sobol sensitivity analysis method,the Monte Carlo sampling,and the coupled normal mode theory,respectively.The results show that the TL is most sensitive to the source depth in the near field,resulted from the initial amplitudes of higher-order modes;while in middle and far fields,the internal waves are responsible for more than 80%of the total acoustic propagation contribution.In addition,the standard deviation of the TL in the near field and the shallow layer is smaller than those in the middle and far fields and the deep layer.

Analytical wave solutions of an electronically and biologically important model via two efficient schemes

We search for analytical wave solutions of an electronically and biologically important model named as the Fitzhugh–Nagumo model with truncated M-fractional derivative, in which the expafunction and extended sinh-Gordon equation expansion(ESh GEE) schemes are utilized. The solutions obtained include dark, bright, dark-bright, periodic and other kinds of solitons. These analytical wave solutions are gained and verified with the use of Mathematica software. These solutions do not exist in literature. Some of the solutions are demonstrated by 2D, 3D and contour graphs. This model is mostly used in circuit theory, transmission of nerve impulses, and population genetics. Finally, both the schemes are more applicable, reliable and significant to deal with the fractional nonlinear partial differential equations.

Existence of Forced Waves and Their Asymptotic for Leslie-Gower Prey-Predator Model with Nonlocal Effects under Shifting Environment

In this paper, we prove the existence of forced waves for Leslie-Gower prey-predator model with nonlocal effects under shifting environment. By constructing a pair of upper and lower solutions with the method of monotone iteration, we can obtain the existence of forced waves for any positive constant shifting speed. Finally, we show the asymptotical behavior of traveling wave fronts in two tails.

Probability Distribution Characteristics of Strong Nonlinear Waves Under Typhoon Conditions in the Northern South China Sea

The generation and propagation mechanism of strong nonlinear waves in the South China Sea is an essential research area. In this study, the third-generation wave model WAVEWATCH Ⅲ is employed to simulate wave fields under extreme sea states. The model, integrating the ST6 source term, is validated against observed data, demonstrating its credibility. The spatial distribution of the occurrence probability of strong nonlinear waves during typhoons is shown, and the waves in the straits and the northeastern part of the South China Sea show strong nonlinear characteristics. The high-order spectral model HOS-ocean is employed to simulate the random wave surface series beneath five different platform areas. The waves during the typhoon exhibit strong nonlinear characteristics, and freak waves exist. The space-varying probability model is established to describe the short-term probability distribution of nonlinear wave series. The exceedance probability distributions of the wave surface beneath different platform areas are compared and analyzed. The results show that with an increase in the platform area, the probability of a strong nonlinear wave beneath the platform increases.

Investigation of Maxima Assumptions in Modelling Tropical Cyclone- Induced Hazards in the South China Sea

The present study aims to examine the suitability of two commonly used assumptions that simplify modelling metoceanconditions for designing offshore wind turbines in the South China Sea (SCS). The first assumption assumes thatjoint N-year extreme wind and wave events can be independently estimated and subsequently combined. The secondone assumes peak wind and waves can be modelled as occurring simultaneously during a tropical cyclone (TC) event.To better understand the potential TC activity, a set of 10000 years synthetic TC events are generated. The wind fieldmodel and the Mike 21 spectral wave model are employed to model the TC-induced hazards. Subsequently, theeffect of the assumptions is evaluated by analyzing the peak structural response of both monopile and semisubmersibleoffshore wind turbines during TC events. The results demonstrate that the examined assumptions are generally accurate.By assessing the implications of these assumptions, valuable insights are obtained, which can inform andimprove the modelling of TC-induced hazards in the SCS region.

Accurate simulations of pure-viscoacoustic wave propagation in tilted transversely isotropic media

Forward modeling of seismic wave propagation is crucial for the realization of reverse time migration(RTM) and full waveform inversion(FWI) in attenuating transversely isotropic media. To describe the attenuation and anisotropy properties of subsurface media, the pure-viscoacoustic anisotropic wave equations are established for wavefield simulations, because they can provide clear and stable wavefields. However, due to the use of several approximations in deriving the wave equation and the introduction of a fractional Laplacian approximation in solving the derived equation, the wavefields simulated by the previous pure-viscoacoustic tilted transversely isotropic(TTI) wave equations has low accuracy. To accurately simulate wavefields in media with velocity anisotropy and attenuation anisotropy, we first derive a new pure-viscoacoustic TTI wave equation from the exact complex-valued dispersion formula in viscoelastic vertical transversely isotropic(VTI) media. Then, we present the hybrid finite-difference and low-rank decomposition(HFDLRD) method to accurately solve our proposed pure-viscoacoustic TTI wave equation. Theoretical analysis and numerical examples suggest that our pure-viscoacoustic TTI wave equation has higher accuracy than previous pure-viscoacoustic TTI wave equations in describing q P-wave kinematic and attenuation characteristics. Additionally, the numerical experiment in a simple two-layer model shows that the HFDLRD technique outperforms the hybrid finite-difference and pseudo-spectral(HFDPS) method in terms of accuracy of wavefield modeling.

A stable staggered-grid finite-difference scheme for acoustic modeling beyond conventional stability limit

Staggered-grid finite-difference(SGFD)schemes have been widely used in acoustic wave modeling for geophysical problems.Many improved methods are proposed to enhance the accuracy of numerical modeling.However,these methods are inevitably limited by the maximum Courant-Friedrichs-Lewy(CFL)numbers,making them unstable when modeling with large time sampling intervals or small grid spacings.To solve this problem,we extend a stable SGFD scheme by controlling SGFD dispersion relations and maximizing the maximum CFL numbers.First,to improve modeling stability,we minimize the error between the FD dispersion relation and the exact relation in the given wave-number region,and make the FD dispersion approach a given function outside the given wave-number area,thus breaking the conventional limits of the maximum CFL number.Second,to obtain high modeling accuracy,we use the SGFD scheme based on the Remez algorithm to compute the FD coefficients.In addition,the hybrid absorbing boundary condition is adopted to suppress boundary reflections and we find a suitable weighting coefficient for the proposed scheme.Theoretical derivation and numerical modeling demonstrate that the proposed scheme can maintain high accuracy in the modeling process and the value of the maximum CFL number of the proposed scheme can exceed that of the conventional SGFD scheme when adopting a small maximum effective wavenumber,indicating that the proposed scheme improves stability during the modeling.

Decoupling Algorithms for the Gravitational Wave Spacecraft

The gravitational wave spacecraft is a complex multi-input multi-output dynamic system.The gravitational wave detection mission requires the spacecraft to achieve single spacecraft with two laser links and high-precision control.Establishing one spacecraftwith two laser links,compared to one spacecraft with a single laser link,requires an upgraded decoupling algorithmfor the link establishment.The decoupling algorithmwe designed reassigns the degrees of freedomand forces in the control loop to ensure sufficient degrees of freedomfor optical axis control.In addressing the distinct dynamic characteristics of different degrees of freedom,a transfer function compensation method is used in the decoupling process to further minimize motion coupling.The open-loop frequency response of the systemis obtained through simulation.The upgraded decoupling algorithms effectively reduce the open-loop frequency response by 30 dB.The transfer function compensation method efficiently suppresses the coupling of low-frequency noise.

Detection of internal crack growth in polyethylene pipe using guided wave ultrasonic testing

Despite the success of guided wave ultrasonic inspection for internal defect detection in steel pipes,its application on polyethylene(PE)pipe remains relatively unexplored.The growth of internal cracks in PE pipe severely affects its pressure-holding capacity,hence the early detection of internal cracks is crucial for effective pipeline maintenance strategies.This study extends the scope of guided wave-based ultrasonic testing to detect the growth of internal cracks in a natural gas distribution PE pipe.Laboratory experiments and a finite element model were planned to study the wave-crack interaction at different stages of axially oriented internal crack growth with a piezoceramic transducer-based setup arranged in a pitch-catch configuration.Mode dispersion analysis supplemented with preliminary experiments was performed to isolate the optimal inspection frequency,leading to the selection of the T(0,1)mode at 50-kHz for the investigation.A transmission index based on the energy of the T(0,1)mode was developed to trace the extent of simulated crack growth.The findings revealed an inverse linear correlation between the transmission index and the crack depth for crack growth beyond 20%crack depth.