Three-dimensional experimental study of loose top-coal drawing law for longwall top-coal caving mining technology

Based on the loose medium flow field theory, the loose top-coal drawing law of longwall top-coal caving（LTCC） mining technology is studied by using self-developed three-dimensional（3D） test device. The loose top-coal drawing test with shields and the controlled test without shields are performed in the condition without any boundary effect. Test results show that shields will cause reduction in drawing volume of coal in the LTCC mining. The deflection phenomenon of drawing body is also observed in the controlled test, which is verified that the deflection of drawing body is caused by shield. It is found that the deflection angle decreases with increasing caving height, with the maximum value of atailand the minimum value of 0. In addition, the formula to calculate the drawing volume is proposed subsequently.The deflection of drawing body is numerically simulated using particle flow code PFC3 Dand the proposed formula to calculate drawing volume in LTCC is also verified.

Study on gob-side entry retaining technique with roadside packing in longwall top-coal caving technology

Pointed out some technical difficulties of gob-side entry retaining with roadside packing in longwall top-coal caving technology (LTCT), and analyzed the function mecha-nism of roadside filling body. Theory analysis shows the mechanical properties of high water material fit for the feature of deformation of gob-side entry retaining in LTCT, and gob-side entry retaining in LTCT face is one of effective ways to increase the recovery ra-tio of mining district.

Numerical and theoretical investigations of the effect of the gangue-coal density ratio on the drawing mechanism in longwall top-coal caving

Discrete element calculations of the top-coal drawing process for diferent gangue-coal density ratios were conducted to investigate the efect of the gangue-coal density ratio on the drawing mechanism in longwall top-coal caving.The efects were analyzed for the drawing body,the top-coal boundary,and the recovery of top coal.The results show that for increasing density ratio,the initial drawing body on the goaf side is farther away from the drawing support and its width and volume gradually increase.The upper part of the sickle-shaped drawing body extends near the initial drawing body with increasing density ratio in the normal cycling stage,and the distance from the drawing body to the initial drawing body is its maximum width.The larger the density ratio,the smaller the height of the top coal above the goaf at the end of the initial drawing process.The height of the top-coal boundary decreases with increasing density ratio,until it reaches a limit.In a normal cycle,due to hysteretic development,the top-coal boundary moves toward the goaf until the density ratio is approximately 2.0,which is consistent with the physical experiment results.Finally,increasing the advance length of the working face is benefcial for increasing the overall recovery of top coal.

Study on Dust-Control WaterInjection in Fully-Mchanized Top-Coal Caving Longwall Faces

Based on the analysis of the top-coal movement, the appropriate position of holes through which dustcoutrol water is injected is confirmed. And a practical test has been carried out, which has achieved good reuslts both in dust control and in the flow rate of water injected into coal.

THE BASIC MECHANICS PROBLEMS AND THE DEVELOPMENT OF LONGWALL TOP-COAL CAVING TECHNIQUE IN CHINA

Since the middle of 1980’s, the longwall top-coal caving technique has beveloped rapidly in China. At present, it is one of the main approaches in the thick coal seam mining. This peper describes some mechanica problems of the caving technique, such as the damage and failure of the top-coal, the strata behaviors in the caving face, and the relation of the support and the surrounding rock. In order to employ the caving technique in a widespred scope, the problems such as the caving technique in the hard coal seam, the moving and running of the loose top-coal,and the upper floating of the gas etc. should be systematically systematically studied.

Fracturing,caving propagation and influence of mining on groundwater above longwall panels–a review of predictive models

Historically there have been a number of different hypotheses and empirical models developed in an attempt to describe the nature of fracturing above longwall panels in underground coal mining.The motivation for suchmodels varies,ranging fromunderstanding the impact ofmining on surface subsidence,to back-analysis of caving behaviour in the immediate roof behind the longwall face.One of the most critical motivating factors that is taking on increased importance in many coalfields,is the need for better understanding,and hence prediction of the impact of mining on overlying strata,particularly strata units acting as aquifers for different groundwater horizons.This paper reviews some of the major prediction models in the context of observed behaviour of strata displacement and fracturing above longwall panels in the southern coalfields of New South Wales,south of Sydney.The paper discusses the parameter often referred to as"height of fracturing"in terms of the critical parameters that influence it,and the relevance and appropriateness of this terminology in the context of overlying sub-surface subsidence and groundwater impact.The paper proposes an alternative terminology for this parameter that better reflects what it is and how it is used.The paper also addresses the potential role of major bedding shear planes mobilised by mining and their potential influence on overlying subsidence and groundwater interference.

Simulation of recovery of upper remnant coal pillar while mining the ultra-close lower panel using longwall top coal caving

With the depletion of easily minable coal seams,less favorable reserves under adverse conditions have to be mined out to meet the market demand.Due to some historical reasons,large amount of remnant coal was left unrecovered.One such case history occurred with the remnant rectangular stripe coal pillars using partial extraction method at Guandi Mine,Shanxi Province,China.The challenge that the coal mine was facing was that there is an ultra-close coal seam right under it with an only 0.8–1.5 m sandstone dirt band in between.The simulation study was carried out to investigate the simultaneous recovery of upper remnant coal pillars while mining the ultra-close lower panel using longwall top coal caving(LTCC).The remnant coal pillar was induced to cave in as top coal in LTCC system.Physical modelling shows that the coal pillars are the abutments of the stress arch structure formed within the overburden strata.The stability of overhanging roof strata highly depends on the stability of the remnant coal pillars.And the gob development(roof strata cave-in)is intermittent with the cave-in of these coal pillars and the sandstone dirt band.FLAC3D numerical modelling shows that the multi-seam interaction has a significant influence on mining-induced stress environment for mining of lower panels.The pattern of the stress evolution on the coal pillars with the advance of the lower working face was found.It is demonstrated that the stress relief of a remnant coal pillar enhances the caveability of the pillars and sandstone dirt band below.

Theoretical description of drawing body shape in an inclined seam with longwall top coal caving mining

Understanding the characteristics of drawing body shape is essential for optimization of drawing parameters in longwall top coal caving mining.In this study,both physical experiments and theoretical analysis are employed to investigate these characteristics and derive a theoretical equation for the drawing body shape along the working face in an inclined seam.By analyzing the initial positions of drawn marked particles,the characteristics of the drawing body shape for different seam dip angles are obtained.It is shown that the drawing body of the top coal exhibits a shape-difference and volume-symmetry characteristic,on taking a vertical line through the center of support opening as the axis of symmetry,the shapes of the drawing body on the two sides of this axis are clearly different,but their volumes are equal.By establishing theoretical models of the drawing body in the initial drawing stage and the normal drawing stage,a theoretical equation for the drawing body in an inclined seam is proposed,which can accurately describe the characteristics of the drawing body shape.The shape characteristics and volume symmetry of the drawing body are further analyzed by comparing the results of theoretical calculations and numerical simulations.It is shown that one side of the drawing body is divided into two parts by an inflection point,with the lower part being a variation development area.This variation development area increases gradually with increasing seam dip angle,resulting in an asymmetry of the drawing body shape.However,the volume symmetry coefficient fluctuates around 1 for all values of the seam dip angle variation,and the volumes of the drawing body on the two sides are more or less equal as the variation development volume is more or less equal to the cut volume.Both theoretical calculations and numerical simulations confirm that the drawing body of the top coal exhibits the shape-difference and volume-symmetry characteristic.

A review of cavability evaluation in longwall top coal caving

Longwall Top Coal Caving has been considered as one of the most effective technologies for the extraction of underground thick coal seams. A large number of studies on the applicability of Longwall Top Coal Caving into new mine sites have linked the success of its application to the geo mechanical understanding of the cavability of the top coal. The paper aims to improve the knowledge of the top coal cavability evaluation. A range of parameters that affect the top coal cavability were first identified. Afterward, a number of cavability assessment methods and classifications were reviewed. The result is important in that it assists researchers in developing an advanced and reliable tool for the top coal cavability evaluation.

Rock mechanical investigation of strata loading characteristics to assess caving and requirement of support resistance in a mechanized powered support longwall face

Longwall mining is one of the most acclaimed and widely used in underground method for coal extraction. The interaction of powered supports with the roof is the key issue in strata mechanics of longwall mining. Controlled caving of rock mass is a prerequisite pro thriving exploitation of coal deposits by longwall retreat with caving technique and support resistance has evolved as the most promising and effective scientific tool to predict various aspects related to strata mechanics of such workings. Load density,height of caving block, distance of fractured zone ahead of the face, overhang of goaf and mechanical strength of the debris above and below the support base have been found to influence the magnitude of load on supports. Designing powered support has been attempted at the different countries in different methods. This paper reviews the mechanism of roof caving and the conventional approaches of caving behaviour and support resistance requirement in the context of major strata control experiences gained worldwide. The theoretical explanation of the mechanism of roof caving is still continuing with consistently improved understanding through growing field experiences in the larger domain of geo-mining conditions and state-of-art strata mechanics analysis and monitoring techniques.

Trial of small gateroad pillar in top coal caving longwall mining of large mining height

Coal seams in Tashan Mine of Datong Coal Group in China average 15 m thick and have been mined by the top coal caving longwall mining method of large mining height. Mining height was 3.8 m and the top coal caving height was 11.2 m. The gateroad pillar between panels was 38 m. During retreat mining,serious bumps occurred in the gateroads on both sides of the pillar affecting safety production. Therefore,pillarless mining was experimented. Using numerical modeling and comparative study of cases of similar mining condition,it was decided to employ a 6 m wide pillar,rather than the previous 38 m wide pillar.Support system for the gateroads was designed and implemented. During gateroad development,pillar failure conditions and entry deformation were monitored. Hydraulic fracturing method was employed to cut off the K3 sandstone along the entry rib so as to reduce the abutment pressure induced during retreat mining. Support reinforcement method combining grouting and advanced reinforcement methods was proposed to insure stable gateroad ahead of mining. Methane drainage and nitrogen injection were implemented to eliminate hazards associated with mine fire and spontaneous combustion. Since the development of gateroad has just completed,and retreat mining has not begun,the effectiveness of the proposed methods is unknown at this point. However,monitoring will continue until after mining.The results will be published in a separate paper.

Drawing mechanisms for top coal in longwall top coal caving(LTCC):A review of two decades of literature

This review details the state of the art in research on top coal drawing mechanisms in Longwall top coal caving(LTCC)by examining the relevant literature over the last two decades.It startswith an introduction of the brief history and basic procedures of LTCC.The framework of research on the drawing mechanism,basic concepts,and some theoretical models of LTCC are detailed in sect.research framework of top coal drawingmechanism.The authors note that theTop coal drawbody(TCD),Top coal boundary(TCB)and Top coal recovery ratio(TCRR)are key factors in the drawingmechanism.TheBody-boundary-ratio(BBR)research system has been the classic framework for research over the last 20 years.The modified Bergmark-Roos model,which considers the effects of the supporting rear canopy,flowing velocity of top coal,and its shape factor,is optimal for characterizing the TCD.A 3Dmodel to describe the TCB that considers the thicknesses of the coal seam and roof strata is reviewed.In sect.physical testing and numerical simulation,the physical tests and numerical simulations in the literature are classified for ease of bibliographical review,and classic conclusions regarding the drawing mechanism of top coal are presented and discussedwith elaborate illustrations and descriptions.The deflection of the TCDis noted,and is caused by the shape of the rear canopy.The inclined coal seam always induces a largerTCD,and a deflection in theTCDhas also been observed in it.The effects of the drawing sequence and drawing interval on the TCRR are reviewed,where a long drawing interval is found to lead to significant loss of top coal.Its flowing behavior and velocity distribution are also presented.Sect.practical applications of drawingmechanisms forLTCCmines 4 summarizes over 10 cases where the TCRRof LTCCmines improved due to the guidance of the drawing mechanism.The final section provides a summary of the work here and some open questions.Prospective investigations are highlighted to give researchers guidance on promising issues in future research on LTCC.

Monitoring strata behavior due to multi-slicing top coal caving longwall mining in steeply dipping extra thick coal seam

For studying the strata behavior due to multi-slicing top coal caving longwall mining along-the-strike direction in steeply dipping extra thick coal seams,the shield support pressures of the upper and lower slices of panel 37220 in Dongxia Coal Mine were monitored using the KJ513 dynamic monitoring system.The set up rooms adopted the "horizontal line-arc segment-inclined line" form and used different types of shield supports.The results show that the strata pressure of upper slice panel 37220-1 changed slightly along the strike direction,while along the dip direction it exhibited strong to weak pressure from bottom to top.The first weighting interval of lower slice panel 37220-2 was about 60.8 m,and the average periodic weighting interval were about 22.6 m.The strata behavior of panel 37220-2 exhibited a spatiotemporal characteristic in that periodic weighting occurred first in the middle-upper part,followed by the middle and upper parts,arc segment,and finally the lower part.During the periodic weighting,the weighting interval and intensity also exhibited strong space characteristics.The average dynamic load coefficient was 1.48 and the maximum lateral load of the side shield was 20-25 MPa.

Theoretical analysis on the deformation characteristics of coal wall in a longwall top coal caving face

Against the background of analyzing coal wall stability in 14101 fully mechanized longwall top coal caving face in Majialiang coal mine,based on the torque equilibrium of the coal wall,shield support and the roof strata,an elastic mechanics model was established to calculate the stress applied on the coal wall.The displacement method was used to obtain the stress and deformation distributions of the coal wall.This study also researched the influence of support resistance,protective pressure to the coal wall,fracture position of the main roof and mining height on the coal wall deformation.The following conclusions are drawn:(1) The shorter the distance from the longwall face,the greater the vertical compressive stress and horizontal tensile stress borne by the coal wall.The coal wall is prone to failure in the form of compressive-shear and tension;(2) With increasing support resistance,the revolution angle of the main roof decreases linearly.As the support resistance and protective force supplied by the face guard increases,the maximum deformation of the coal wall decreases linearly;(3) As the face approaches the fracture position of the main roof,coal wall horizontal deformation increases significantly,and the coal wall is prone to instability;and(4) The best mining height of 14101 longwall face is 3.0 m.

Conventional approaches for assessment of caving behaviour and support requirement with regard to strata control experiences in longwall workings

Effective control of roof strata is very important for trouble free operation and regular face advance in mechanised longwall workings. It is now technically possible to exploit coal seams in difficult geomining conditions with the help of newer innovations in longwall face machineries. A reliable assessment of caving behaviour and support capacity requirement helps in selecting supports of adequate capacity and making operational preparedness for timely and confident solution of impending problems.This paper reviews the mechanism of roof caving and the conventional approaches of caving behaviour and support requirement in the context of major strata control experiences gained worldwide. The review shows that a number of approaches are being used for advance prediction of caving behaviour and support capacity requirement in a variety of geo-mining conditions. The theoretical explanation of the mechanism of roof caving and the design function of roof supports have been worked out through staged development of approaches, their evaluation followed by their gradual modification and enrichment of synthesized findings. This process is still continuing with consistently improved understanding through growing field experiences in the larger domain of geo-mining conditions and state-of-art strata analysis and monitoring techniques. These attempts have contributed significantly to improving the level of understanding and reducing the gap of uncertainty in planning and design of longwall operation in a given geo-mining condition.

A new fracture model for the prediction of longwall caving characteristics

A new numerical model is presented to simulate fracture initiation and propagation in geological structures. This model is based on the recent amalgamation of established failure and fracture mechanics theory, which has been implemented to the finite difference FLAC code as a constitutive FISH userdefined-model. Validation of the model has been studied on the basis of comparing the transitional failure modes in rock. It is shown that the model is capable of accurately simulating fracture distributions over entire brittle to ductile rock phases. The application of the model during longwall retreat simulation highlighted several caving characteristics relevant to varying geological condition. The distribution and behaviour of modelled fractures were both realistic and shown to provide an enhanced post failure analysis to geological structures in FLAC. Moreover, the model introduces new potential insight towards the failure analysis of more complicated problems. This is best suited towards improving safety and efficiency in mines through the prediction of various key fractures and caving characteristics of geological structures.

Systematic principles of surrounding rock control in longwall mining within thick coal seams

Effective surrounding rock control is a prerequisite for realizing safe mining in underground coal mines.In the past three decades, longwall top-coal caving mining(LTCC) and single pass large height longwall mining(SPLL) found expanded usage in extracting thick coal seams in China. The two mining methods lead to large void space left behind the working face, which increases the difficulty in ground control.Longwall face failure is a common problem in both LTCC and SPLL mining. Such failure is conventionally attributed to low strength and high fracture intensity of the coal seam. However, the stiffness of main components included in the surrounding rock system also greatly influences longwall face stability.Correspondingly, surrounding rock system is developed for LTCC and SPLL faces in this paper. The conditions for simultaneous balance of roof structure and longwall face are put forward by taking the stiffness of coal seam, roof strata and hydraulic support into account. The safety factor of the longwall face is defined as the ratio between the ultimate bearing capacity and actual load imposed on the coal wall.The influences provided by coal strength, coal stiffness, roof stiffness, and hydraulic support stiffness,as well as the movement of roof structure are analyzed. Finally, the key elements dominating longwall face stability are identified for improving surrounding rock control effectiveness in LTCC and SPLL faces.

Current Situation and Prospect of Top-Coal Caving Technology in China

A great development has been achieved on thick seam longwall top-coal caving technology in China for the recent years, which has raised face output and efficiency and reduced production cost greatly. In this paper, achievements in its production, safety and theoretical research and future tasks are discussed.

Dimensionless model to determine spontaneous combustion danger zone in the longwall gob

According to spontaneous combustion propensity,the longwall gob is divided into three zones,including heat dissipation zone,self-heating zone and the choking zone.Only in the self-heating zone can temperature of coal rise due to oxidation.Studying the distribution of the "Three Zones" in gob is important for predicting and preventing spontaneous combustion in coalmine.In normal mining operations,temperature of coal is roughly constant.The process of mass transfer in the gob is considered to be steady.Based on mass conservation,gas species conservation,darcy's law,Ficks law of diffusion and coal oxidation 1-grade reaction rule,governing equation for air leakage intensity and species concentration are deduced.With critical value of coal spontaneous combustion and the size of longwall workface as basic dimension,a dimensionless steady coupled model of air flow diffusion and chemical reaction in loose coal of Fully Mechanized Top-Coal Caving Mining Workface(FMTCCMW) is setup.By solving the model numerically,regulation of three zones' distribution and spontaneous combustion in the gob can be obtained.The results can be easily popularized to prediction of spontaneous combustion in other coalmines' longwall gob.