Properties of Activated Carbons from Sugarcane Leaves and Rice Straw Derived Charcoals by Activation at Low Temperature via KMnO_(4)Pre-Oxidation-Hydrolysis

Activated carbon preparation from sugarcane leaves and rice straw by carbonization(250℃–400℃)and activation at 500℃were studied.The effects of pre-oxidation,hydrolysis of derived charcoals by boiled KMnO4 aqueous solution were evaluated.The derived charcoals products were pretreated using oxidation-hydrolysis with 1–5 wt.%KMnO4 at 100℃and then activated at 500℃.The derived charcoal and activated carbon products were characterized by FTIR,XRD,SEM-EDS and BET.Iodine number and methylene blue number of derived products were also used for the analysis of the products.It was found that fabricated charcoal materials made at 350℃–400℃possess good characteristics with low content of surface functional groups and high carbon content.After pre-oxidation-hydrolysis and activation at 500℃,the resulting derived activated carbon materials from charcoals with 400℃carbonization temperature have high content of oxygen containing surface functional groups such as Mn-O,Si-O,Si-O-Si,C-O,or O-H.In addition,MnO_(2) accumulated on the surface of the derived activated carbon products.The surface area and pore volume of the activated carbon products have also increased with increasing of KMnO_(4) concentration from 1 to 3 wt.%and then decreased with 5 wt.%used during activation.Therefore,activated carbon products made by pre-oxidation-hydrolysis with 3 wt.%KMnO_(4) were used for Fe(Ⅲ)adsorption experiments.It was found that Fe(Ⅲ)adsorption on the activated carbon materials can be fitted with both the Freundlich and the Langmuir models.The calculated maximum Fe(Ⅲ)adsorption capacities of sugarcane leaves derived activated carbon and rice straw derived activated carbon products were 50.00 and 39.37 mg/g,respectively.It was shown that the effect of pre-oxidation-hydrolysis by KMnO_(4) and activation at 500℃are beneficial for activated carbon preparation with environmentally friendly and low-cost simplified operation.

Selective catalytic NO_x reduction on Antimony promoted V_2O_5-Sb/TiO_2 catalyst

Quantum chemical calculation was carried out to choose a promoter which can reduce the poisoning of V2O5/TiO2 catalysts by SO2. Several atoms were chosen as candidates and new catalysts were synthesized by impregnation method. The NOx conversion rate was measured at temperatures between 100 and 400 ℃ and poisoning effect was investigated. The most promising candidate promoter, Se, was excluded because of its high vapor pressure. On the other hand, Sb shows best promoting properties. Sb promoted catalyst reaches the maximum NOx conversion rate at 250 ℃. It also shows considerably enhanced resistance to poisoning of V2O5/TiO2 catalysts by SO2.

Research on Diamond Enhanced Tungsten Carbide Composite Button

At the present, the cutters used in button bits and rock bits are mainly cobalt tungsten carbide in our country. Because of its low abrasive resistance, the bit service life and drilling efficiency was very low when the hard and extremely hard formations were being drilled. Owing to its high abrasive resistance, the diamond composite material is widely used in drilling operations. However, its toughness against impact is too low to be used in percussion drilling, only can it be used in rotary drilling. In order to solve the problems encountered by DTH hammer in hard rock drilling, make bit life longer, increase rate of penetration and decrease drilling cost, a new type diamond enhanced tungsten carbide composite button with high abrasive resistance and high toughness against impact, which may be used in percussion drilling, has been developed. The key problems to make the button are to improve the thermal stability of diamond, to increase the welding strength between diamond and cemented tungsten carbide, and to lower the sintering temperature of tungsten carbide. All these problems have been solved effectively by pretreatment of diamond, low temperature activation hot-press sintering and high sintering pressure. (1) To plate tungsten on the surface of diamond. Diamond suffers easily from erosion in the environment of high temperature containing oxygen and iron family elements. There is very high energy between the interface of diamond and bonding metal and so the metallurgical bond can’t form at the interface between diamond and bond metal. This will lower greatly the bending strength and the toughness against impact of diamond enhanced tungsten carbide composite button. In order to improve thermal stability of diamond and increase the bonding strength of the interface between diamond and bond metal, to plate tungsten on the surface of diamond by vacuum vapor deposit is adopted. (2) To lower the sintering temperature by adding nickel, phosphorus and boron etc into conventional mixed powder. In general, the sintering temperature of cemented tungsten carbide is more than 1 350 ℃ in which diamond will suffer from serious heat erosion, so the sintering temperature must be lowered. To add nickel, phosphorus and boron etc into cobalt-base bond whose melting point is more than 1 350 ℃ will lower the sintering temperature to about 1 050 ℃. To add phosphorus can lower the temperature of liquid phase occurring and promote the densification of matrix alloy in advance because the co-crystallization temperature of Ni-P and Co-P is 880 ℃ and 1 020 ℃ respectively. The proper adding amount of nickel, phosphorus and boron etc is a key problem. To substitute nickel for partial cobalt can improve the toughness against impact of diamond enhanced tungsten carbide composite button and lower the sintering temperature. To add boron is helpful for sintering and improving the toughness against impact of diamond enhanced tungsten carbide composite button. (3) To increase the sintering press. Under the same sintering temperature, to improve the sintering press can improve the density and strength of sintering products. In this study to increase the sintering press 35 MPa in the usual conditions to 50～60 MPa in sintering diamond enhanced tungsten carbide button by adopting ceramic material as pressing rod has improved the sintering quality effectively. The properties of the button have been measured under lab conditions. The testing results show that its hardness is more than HRA86 and that its abrasiveness resistance is 100 times more than conventional cemented tungsten carbide, and its toughness against impact is more than 100J. All these data theoretically show that the button has very good mechanical properties that can meet the need of percussion drilling, and can solve the problems encountered with button bit of conventional cemented tungsten carbide.

Effects of SO2 on the low temperature selective catalytic reduction of NO by NH3 over CeO2-V2O5-WO3/TiO2 catalysts

The CeO2-V2O5-WO3/TiO2 （CeO2-VWT） catalysts were prepared by one-step and two-step impregnation methods. The effects of different loading of CeO2 and different preparation methods on De-NOx activity of catalysts had been investigated. CeO2 helped to improve the De-NOx activity and sulfur resistance. The optimal loading of CeO2 was 3% with the De-NOx efficiency reached 89.9% at 140℃. The results showed that the De-NOx activity of 3% CeO2-VWT catalysts by one-step method was the same as two-step method basically and reached the level of industrial applications, the N2 selectivity of catalysts was more than 99.2% between 110℃ and 320℃. In addition, CeO2 promoted the oxidation of NO to NO2, which adsorbed on the Lewis acid site （V5＋-O） to form V5＋-NO3 and inspired the fast SCR reaction. Not only the thermal stability but also the De-NOx activity of catalysts decreased with excess CeO2 competed with V2O5. Characterizations of catalysts were carried out by XRF, BET, XRD, TG and FT-IR. BET showed that the specific surface area of catalysts decreased with the loading of CeO2 increased, the active components content and specific surface area of catalysts decreased slightly after entering SO2. Ammonium sulfate species were formed in poisoned catalyst which had been investigated by XRF, BET, TG and FT-IR. The largest loss rate of weight fraction was 0.024%.℃-1 at 380℃ 390℃, which was in accordance with the decomposition temperature of NH4HSO4 and （NH4）2SO4,

Activity Enhancement of Vanadium Catalysts with Ultrasonic Preparation Process for the Oxidation of Sulfur Dioxide

The effect of ultrasonic cavitations on the activity of vanadium catalysts atlow temperatures for the oxidation of sulfur dioxide, in which refined carbonized mother liquor hadbeen added, was investigated. Twenty minutes were needed to produce obvious cavitations when thecatalyst raw material was treated in the 50 W ultrasonic generator. However, only 10 minutes wouldbe needed in a 150 W ultrasonic generator. The higher the temperature of the wet material, the lesstime was needed to produce cavitations, and the optimal temperature was 60℃. The water content inthe wet material mainly affected the quantity of cavitations. Ls-8 catalyst was prepared usingultrasonic. Its activity for conversion of SO_2 reached to 52.5% at 410℃ and 4.2% at 350℃. Thedifferential thermal analyses indicate that both endothermic peaks and exothermic peaks noticeablyshifted forward compared with Ls catalyst prepared without ultrasonic, and SEM results show auniform pore size distribution for Ls-8 catalyst.

Preparation of Cs-Rb-V series sulphuric acid catalyst

Cs Rb V series low temperature sulphuric acid catalyst was prepared for the first time by using carbonized mother liquor containing alkali metal salts. The results show that the conversion of SO 2 on catalyst prepared directly with carbonized mother liquor could reach to 24.8% at 410?℃. If n (Na)/ n (V) was adjusted properly, the conversion of SO 2 could be increased to 35.6% at 410?℃. Refined carbonized mother liquor could make the catalytic activity even higher at low temperature, the conversion of SO 2 could be increased to 36.65% at 410?℃. The catalyst was examined with differential thermal analysis. It was found that both endothermic peaks and exothermic peaks of catalyst shifted forward obviously and the catalyst possessed higher activity at low temperature.

Screening Psychrophilic Fungi of Cellulose Degradation and Characteristic of Enzyme Production

A fungus（WR-C1） decomposed cellulose was isolated from a hypothermal litter layer using Congo red medium as the preliminary screening culture medium and then using a filter as the secondary screening medium at low temperature. The experiment showed that the weight loss rate of filter paper on the 15 th days could reach 30.69%. A morphologic and ITS gene sequence analysis suggested that CF-C1 was Cladosporium. We mainly studied the effects of culture time, inoculation amount, initial p H and different sources of carbon, nitrogen and inorganic salt on the cellulase production of strain WR-C1. Under optimum cultural condition, the highest value of WR-C1 enzyme production and filter paper enzyme were 3.27 U · m L～（-1） and 0.51 U · m L～（-1）.

Study on Oxidation Activity of CuCeZrO_x Doped with K for Diesel Engine Particles in NO/O_2

CuCeZrO_x and KCuCeZrO_x catalysts were synthesized and coated on the blank diesel particulate filter(DPF)substrate and a particulate matter(PM)loading apparatus was used for soot loading.The catalytic performances of soot oxidation were evaluated by temperature programmed combustion(TPC)test and characterization tests were conducted to investigate the physicochemical properties of the catalysts.The reaction mechanism in the oxidation process was analyzed with diffuse reflectance infrared Fourier transform spectroscopy.The results demonstrated that CuCeZrO_x catalyst exhibited high activities of soot oxidation at low temperature and the best results have been attained with Cu_(0.9)Ce_(0.05)Zr_(0.05)O_x over which the maximum soot oxidation rate decreased to 410~?C.Characterization tests have shown that catalysts containing 90%Cu have uniformly distributed grains and small particle sizes,which provide excellent oxidation activity by providing more active sites and forming a good bond between the catalyst and the soot.The low-temperature oxidation activity of soot could be further optimized due to the excellent elevated NO’s conversion rate by partially substituting Cu with K.The maximum particle oxidation rate can be easily realized at such a low temperature as 347~?C.

Deposition and characterization of Pd-Ti thin film by sublimation

Introduction Pd/Ti double-layer thin film as non-evaporable getter(NEG)was deposited by sublimation,and its activation temperature was as low as 100℃.The Pd film was deposited in situ after Ti deposition to ensure no oxidization on Ti film.Pumping speed test and characterization method The pumping speed of the coated pipe was measured by a pumping speed test system.The sticking factor was calculated by Molflow.The surface morphology was observed by a scanning electron microscope(SEM).The chemical composition of the film was measured by an energy-dispersive spectrum inbuilt with the SEM.The crystalline structure of the film was measured using grazing incidence X-ray diffraction.Conclusion It was found that the pumping performance of the Pd/Ti film still remained high after 15 times of activation.The maximum pumping speed after heating at 100℃for 24 h was 1.1 L/s cm^(2)and 0.49 L/s cm^(2)for H_(2)and CO,respectively.It can be concluded that the key to reducing the activation temperature of NEG materials is to enhance the oxidation resistance of the surface of NEG.