Producing ultra-high-speed nitrogen jets by arc heating in a low-pressure chamber

Pure nitrogen gas was heated with direct current arc, at input powers from several hundred Watt to over 5 kW, and then injected through a nozzle into a chamber at 1 or 10 Pa pressure, with the purpose of accelerating the gas to very high speed around 7 km/s. Various structures of the arc generator and gas expansion nozzle were examined. Results show that bypass exhausting of the boundary layer before it enters the nozzle divergent section can greatly increase flow speed of the jet, thus it might be possible to use nitrogen as a working gas in high speed gas dynamic test facilities.

A new vacuum-assisted low-pressure investment casting process for K446 alloy

Non-metallic inclusions and zyglo indications frequently occur in the superalloy castings produced through the traditional vacuum gravity investment casting process,particularly in components with thin-walled and complex structural features.The vacuum-assisted low-pressure casting(VLC),a type of counter-gravity casting(CGC)method,has been developed to minimize non-metallic inclusions and zyglo indications in superalloy castings.Rectifying frames for gas turbines made from K446 alloy were produced semi-continuously using the VLC process and subsequently evaluated through tensile testing,chemical composition analysis,X-ray diffraction,and zyglo penetrant inspection.The results indicate a roughly 10%improvement in tensile strength at 800℃ compared to gravity casting.Moreover,no significant changes are observed in the chemical composition of the alloys from the beginning to the end of a casting campaign,indicating that the developed VLC process is viable for the engineering-scale production of superalloy castings.Compared to traditional vacuum gravity casting(GC)method,the application of VLC can reduce the numbers of non-metallic inclusions and Zyglo indications in the castings by over 80%.At the same time,it significantly shortens the production time by 3 to 5 days.

Optimization of pressurization process in low-pressure casting of a 5.4-ton gigantic C95800 copper alloy casting

During the low-pressure casting of extra-large size C95800 copper alloy components,traditional linear pressurization technique leads to a rapid surge of liquid metal inlet velocity at the regions where the mold cavity cross-section enlarges.This rapid increasement of liquid metal inlet velocity causes serious entrapment of gas and oxide films,and results in various casting defects such as the bifilm defects.These defects detrimentally deteriorate mechanical properties of the castings.To address this issue,an innovative nonlinear pressurization strategy timely matching to the casting structure was proposed.The pressurization rate decreases at sections where the cross-section widens,but it gradually increases as the liquid metal level rises.By this way,the inlet velocity remains below a critical threshold to prevent the entrapment of gas and oxide films.Comparative analyses involving numerical simulations and casting verification illustrate that the nonlinear pressurization technique,compared to the linear pressurization,effectively diminishes both the size and number of bifilm defects.Furthermore,the nonlinear pressurization method enhances the casting yield strength by 10%,tensile strength by 14%,and elongation by 10%.Examination through scanning electron microscopy highlights that the bifilm defects arising from the linear pressurization process result in the reduction of the castings’mechanical properties.These observations underscore the efficacy of nonlinear pressurization in enhancing the quality and reliability of gigantic castings,as exemplified by a 5.4-ton extra-large sized C95800 copper alloy propeller hub with complex structures in the current study.

Photoionization Mass Spectrometric and Kinetic Modeling of Low-pressure Pyrolysis of Benzene

Pyrolysis of benzene at 30 Torr was studied from 1360 K to 1820 K in this work. Synchrotron vacuum ultraviolet photoionization mass spectrometry was employed to detect the pyroly- sis products such as radicals, isomers and polycyclic aromatic hydrocarbons, and measure their mole fraction profiles versus temperature. A low-pressure pyrolysis model of benzene was developed and validated by the experimental results. Rate of production analysis was performed to reveal the major reaction networks in both fuel decomposition and aromatic growth processes. It is concluded that benzene is mainly decomposed via H-abstraction reaction to produce phenyl and partly decomposed via unimolecular decomposition reac- tions to produce propargyl or phenyl. The decomposition process stops at the formation of acetylene and polyyne species like diacetylene and 1,3,5-hexatriyne due to their high thermal stabilities. Besides, the aromatic growth process in the low-pressure pyrolysis of benzene is concluded to initiate from benzene and phenyl, and is controlled by the even carbon growth mechanism due to the inhibited formation of C5 and C7 species which play important roles in the odd carbon growth mechanism.

Low-pressure pneumoperitoneum with abdominal wall lift in laparoscopic total mesorectal excision for rectal cancer:initial experience

AIM To evaluate the safety and feasibility of a new technology combining low-pressure pneumoperitoneum(LPP) and abdominal wall lift(AWL) in laparoscopic total mesorectal excision(TME) for rectal cancer.METHODS From November 2015 to July 2017,26 patients underwent laparoscopic TME for rectal cancer using LPP(6-8 mm Hg) with subcutaneous AWL in Qilu Hospital of Shandong University,Jinan,China.Clinical data regarding patients' demographics,intraoperative monitoring indices,operation-related indices andpathological outcomes were prospectively collected.RESULTS Laparoscopic TME was performed in 26 cases(14 anterior resection and 12 abdominoperineal resection) successfully,without conversion to open or laparoscopic surgery with standard-pressure pneumoperitoneum.Intraoperative monitoring showed stable heart rate,blood pressure and paw airway pressure.The mean operative time was 194.29 ± 41.27 min(range:125-270 min) and 200.41 ± 20.56 min(range:170-230 min) for anterior resection and abdominoperineal resection,respectively.The mean number of lymph nodes harvested was 16.71 ± 5.06(range:7-27).There was no positive circumferential or distal resection margin.No local recurrence was observed during a median follow-up period of 11.96 ± 5.55 mo(range:5-23 mo).CONCLUSION LPP combined with AWL is safe and feasible for laparoscopic TME.The technique can provide satisfactory exposure of the operative field and stable operative monitoring indices.

Process Optimization for AZ91 Mg-alloy Low-pressure EPC Process

The influence of a key process variable on the mold filling characteristics of AZ91 Mg-alloy was studied in the low pressure EPC process.The applied flow quantity of insert gas from 1 to 5 m~3/h associated with the pressurizing rate in the low pressure EPC casting process was considered for rectangle and L-shape plate casting. The experimental results show that there is an optimal flow quantity of insert gas for good mold filling characteristics in AZ91 Mg-alloy low-pressure EPC process. The optimal flow quantity of insert gas for the specimens is 3 to 4 m~3/h. Either less or higher than the optimal flow quantity of insert gas would lead to misrun defects or folds, blisters and porosity defects. The practice of hub casting confirmed that the low-pressure EPC process with an optimal processing variable exemplified as 4 m~3/h gas flow quantity was capable of producing complicated magnesium castings without misrun defects.

Numerical simulation and analysis of lithium plasma during low-pressure DC arc discharge

Alkali metal DC arc discharge has the characteristics of easy ionization,low power consumption,high plasma temperature and ionization degree,etc,which can be applied in aerospace vehicles in various ways.In this paper,we calculate the physical property parameters of lithium vapor,one of the major alkali metals,and analyze the discharge characteristics of lithium plasma with the magnetohydrodynamic(MHD)model.The discharge effects between constant current and voltage sources are also compared.It is shown that the lithium plasma of DC arc discharge has relatively high temperature and current density.The peak temperature can reach tens of thousands of K,and the current density reaches 6 x 107 A m 2.Under the same rated power,the plasma parameters of the constant voltage source discharge are much higher than those of the constant current source discharge,which can be used as the preferred discharge mode for aerospace applications.

An Experimental and Numerical Study on the Cleaning of Pleated Bag Filters Using Low-Pressure Pulsed-Jets

Pulsed-jet cleaning is recognized as the most efficient method to regenerate bag dust collectors traditionally used in industrial processes to control the emission of particulates.In this study,non-woven needle felt filter bags with and without a film coating material have been analyzed considering different geometries(different number N of pairs of pleated filter bag sides)in the frame of dedicated low-pressure pulsed-jet cleaning experiments.The flow structure inside the bag and the response characteristics of its wall have also been analyzed numerically through a computational fluid-dynamics/structural-dynamics(CFD-CSD)unidirectional fluid-solid coupling method.As shown by the experiments,the peak pressure(P_(0))on the wall of the filter bag with N=8 and 12 is higher,which indicates dust can be removed more effectively in these cases.The peak pressure on the wall increases first and then decreases along the direction of the bag length,while the peak pressure of the pleated filter bag with nonwoven needled felt film coating is greater than that without film coating.A comprehensive analysis of the time variation of acceleration,deformation,strain,stress and other factors,has led to the conclusion that the pleated filter bag with N=12 would be the optimal choice.

The mechanism study of low-pressure air plasma cleaning on large-aperture optical surface unraveled by experiment and reactive molecular dynamics simulation

Low-pressure air plasma cleaning is an effective method for removing organic contaminants on large-aperture optical components in situ in the inertial confinement fusion facility.Chemical reactions play a significant role in plasma cleaning,which is a complex process involving abundant bond cleavage and species generation.In this work,experiments and reactive molecular dynamics simulations were carried out to unravel the reaction mechanism between the benchmark organic contaminants of dibutyl phthalate and air plasma.The optical emission spectroscopy was used to study the overall evolution behaviors of excited molecular species and radical signals from air plasma as a reference to simulations.Detailed reaction pathways were revealed and characterized,and specific intermediate radicals and products were analyzed during experiments and simulation.The reactive species in the air plasma,such as O,HO_(2)and O_(3)radicals,played a crucial role in cleaving organic molecular structures.Together,our findings provide an atomic-level understanding of complex reaction processes of low-pressure air plasma cleaning mechanisms and are essential for its application in industrial plasma cleaning.

Effect of Low-pressure Carbonation on the Heat Inactivation and Cytoplasmic Acidification of Saccharomyces cerevisiae

Effect of low-pressure carbonation （LPC） on heat inactivation of Saccharomyces cerevisiae was investigated. The cell suspension was carbonated at 1 MPa and 4℃ for 15 min and subsequently heated from 51 to 61 ℃ and 5 s to 5 min （heating with LPC）. As a control experiment, cell suspension was heat-treated under atmospheric pressure without LPC （heating）. The inactivation ratio of heating at 53℃ and 55℃ for l rain with LPC was approximately 1 log order higher than heating alone. Extending heating time to 5 min did not widen the difference in the inactivation ratio between heating with LPC and heating alone at both heating temperatures. At 57℃, the difference in inactivation ratio increased from 1 to 2.5 log order with extending treatment time from 5 to 15 s. The results suggested that the enhanced inactivation effect by LPC was obtained at the higher temperature with short time treatment than the lower temperature with longer time treatment. Under fluorescence microscope observation of LPC-treated cell stained with LysoSensor probe, it seemed that LPC was hardly able to acidify the cytoplasm ofS. cerevisiae. It is considered that the ability orS. cerevisiae ceils to keep their cytoplasmic pH during LPC resulted in the inferior increase in heat inactivation ratio by LPC as compared with bacteria in the previous studies.

Neutrons in a nanosecond low-pressure discharge in deuterium

Stable neutron generation with a yield of ~1.2×10^(4) neutrons per pulse was obtained during d(d,n)^(3)He reaction initiated by the high-voltage nanosecond discharge in a gap with a potential tungsten cylinder(anode)and a grounded deuterated zirconium plate(cathode)filled with deuterium at a pressure of ~10^(2) Pa.Estimated duration of the neutron pulse was ~1.5 ns.Less intensive neutron emission was registered without deuterated plate.Splashing of material of the tungsten electrode was observed during the high-voltage nanosecond discharge in the deuterium,hydrogen,helium and argon at pressures of 10^(2)-10^(4) Pa.

A LOW-PRESSURE AND ONE-STEP METHOD FOR THE SYNTHESIS OF ALKYLIDYNETRICOBALT NONACARBONYL CLUSTERS:RCCo_8(CO)_9

Metal clusters RCCo_3(CO)_9(R-H,C1,Br,CH_3,Ph) were prepared in 18.8-57.3% yields from the reaction of cobalt(Ⅱ)salt and RCX_a under mild PTC conditions(latm CO,25℃).The cobalt salt was reduced to Co(CO)_4 in the presence of Na_3S_2O_4.

Simulation of propagation of the HPM in the low-pressure argon plasma

The propagation of the high-power microwave（HPM） with a frequency of 6 GHz in the lowpressure argon plasma was studied by the method of fluid approximation.The two-dimensional transmission model was built based on the wave equation,the electron drift-diffusion equations and the heavy species transport equations,which were solved by means of COMSOL Multiphysics software.The simulation results showed that the propagation characteristic of the HPM was closely related to the average electron density of the plasma.The attenuation of the transmitted wave increased nonlinearly with the electron density.Specifically,the growth of the attenuation slowed down as the electron density increased uniformly.In addition,the concrete transmission process of the HPM wave in the low-pressure argon plasma was given.

Microstructure and Properties of Low-pressure Cold Sprayed Al-based Composite Coatings on Magnesium Alloy Surface

Pure Al and Al-30%Al_(2)O_(3)composite coatings are prepared on the surface of AZ31B magnesium alloy by low-pressure cold spraying.The morphology and structure of the coatings are analyzed by scanning electron microscope (SEM),energy dispersive spectroscopy (EDS),and X-ray diffraction (XRD),and the effects of the addition of Al_(2)O_(3)on the microstructure of the Al-based coatings are discussed.The mechanical properties and corrosion resistance of the coatings are fully evaluated by the micro-hardness tester,electronic tensile machine,and electrochemical workstation.The results show that the coating structure is more uniform and denser,and the porosity is significantly reduced after the addition of Al_(2)O_(3).The interfaces between the coatings and the magnesium alloy substrate are distinct,and the coatings and the substrate are mechanically combined.Compared with the pure Al coating,the microhardness of the Al-Al_(2)O_(3)composite coating is increased to 61.1 HV_(0.2),and the bonding strength reaches above 53.1 MPa.The self-corrosion potential of the two coatings is higher than that of the magnesium alloy,and the self-corrosion current density is significantly lower than that of the magnesium alloy substrate.The Al-based coatings prepared by low-pressure cold spraying have high hardness,good bonding strength,and good corrosion resistance,which can be used for the repair and protection of magnesium alloy structural parts.

Simulation and reconstruction of particle trajectories in the CEPC drift chamber

The circular electron-positron collider(CEPC)is designed to precisely measure the properties of the Higgs boson,study electroweak interactions at the Z-boson peak,and search for new physics beyond the Standard Model.As a component of the 4th conceptual CEPC detector,the drift chamber facilitates the measurement of charged particles.This study implemented a Geant4-based simulation and track reconstruction for the drift chamber.For the simulation,detector construction and response were implemented and added to the CEPC simulation chain.The development of track reconstruction involves track finding using the combinatorial Kalman filter method and track fitting using the tool of GenFit.Using the simulated data,the tracking performance was studied.The results showed that both the reconstruction resolution and tracking efficiency satisfied the requirements of the CEPC experiment.

Fudan multi-purpose active target time projection chamber(fMeta-TPC)for photonuclear reaction experiments

Active target time projection chambers are state-of-the-art tools in the field of low-energy nuclear physics and are particularly suitable for experiments using low-intensity radioactive ion beams or gamma rays.The Fudan multi-purpose active target time projection chamber(fMeta-TPC)with 2048 channels was developed to studyα-clustering nuclei.This study focused on the photonuclear reaction with a laser Compton scattering gamma source,particularly for the decay of the highly excitedαcluster state.The design of fMeta-TPC is described in this paper.A comprehensive evaluation of its offline performance was conducted using an ultraviolet laser and ^(241)Amαsource.The results showed that the intrinsic angular resolution of the detector was within 0.30°,and the detector had an energy resolution of 6.85%for 3.0 MeVαparticles.The gain uniformity of the detector was approximately 10%(RMS/Mean),as tested by the ^(55)Fe X-ray source.

Effect of coil and chamber structure on plasma radial uniformity in radio frequency inductively coupled plasma

Enhancing plasma uniformity can be achieved by modifying coil and chamber structures in radio frequency inductively coupled plasma(ICP)to meet the demand for large-area and uniformly distributed plasma in industrial manufacturing.This study utilized a two-dimensional self-consistent fluid model to investigate how different coil configurations and chamber aspect ratios affect the radial uniformity of plasma in radio frequency ICP.The findings indicate that optimizing the radial spacing of the coil enhances plasma uniformity but with a reduction in electron density.Furthermore,optimizing the coil within the ICP reactor,using the interior point method in the Interior Point Optimizer significantly enhances plasma uniformity,elevating it from 56%to 96%within the range of the model sizes.Additionally,when the chamber aspect ratio k changes from 2.8 to 4.7,the plasma distribution changes from a center-high to a saddleshaped distribution.Moreover,the plasma uniformity becomes worse.Finally,adjusting process parameters,such as increasing source power and gas pressure,can enhance plasma uniformity.These findings contribute to optimizing the etching process by improving plasma radial uniformity.

Clinical Effect Analysis of Posterior Chamber Intraocular Lens Implantation for Correcting High Myopia and Astigmatism

Objective:To explore the corrective effect of posterior chamber intraocular lens implantation with phakic eyes in the treatment of high myopia and astigmatism.Methods:From May 2023,the hospital began to collect the case data of diagnosis and treatment of high myopia and astigmatism.By May 2024,310 cases were included,all of which were treated with posterior chamber intraocular lens implantation.The visual acuity,astigmatism and axial position of the intraocular lens were observed before and after treatment.Results:At different time points after the operation,the patient’s vision was significantly improved compared with that before the operation(P<0.05),and the vision level was equal to or greater than the best-corrected vision before the operation.At different time points after the operation,the average rotation of the intraocular lens was less than 5 degrees.Astigmatism was significantly lower than that before the operation(P<0.05).After the operation,the intraocular pressure increased in 11 cases,accounting for 3.55%,with no adverse complications such as lens turbidity,glare and obvious halo occurring.Conclusion:The posterior chamber intraocular lens implantation with phakic eyes has an ideal correction effect in the treatment of high myopia and astigmatism,which can effectively improve the vision level of patients and reduce the degree of astigmatism,and has high effectiveness and safety.

罗丹明123经大鼠空肠黏膜的体外Ussing chamber渗透研究

目的:检测并评价罗丹明123(R123)经空肠黏膜渗透的特点,分析此法的可行性。方法:配制R123溶液,采用体外Ussing chamber实验法,考察R123经时经大鼠空肠黏膜吸收方向和分泌方向的累计透过量,并计算各自渗透系数。结果:R123吸收和分泌方向的表观渗透系数Papp(×10-5,cm.s-1)分别为(1.9±1.3)和(7.4±5.2),差异具显著性。结论:R123作为P-糖蛋白的底物,其经肠黏膜渗透以分泌方向为主;Ussing chamber实验用于评价药物在肠道内转运具有易操作,简便等特点,值得推广使用。

基于Ussing Chamber技术的红景天苷大鼠肠黏膜透过性研究

[目的]研究红景天苷在大鼠离体肠黏膜中的透过情况。[方法]采用Ussing Chamber技术,考察不同浓度红景天苷于大鼠肠黏膜透过情况,并考察维拉帕米(Ver)和十二烷基硫酸钠(SDS)对红景天苷大鼠肠黏膜透过的影响。[结果]不同浓度红景天苷在大鼠不同肠段的单位时间转运速率(Flux)随浓度升高而增大,不同肠段表观渗透系数(P_(app))无统计学差异(P>0.05)。Ver加入一定量的SDS后,红景天苷在回肠和结肠的P_(app)显著增加(P<0.01或P<0.05),当SDS浓度为2 g/L时,回肠P_(app)增加为对照组的2.76倍。[结论]红景天苷在大鼠全肠段均有吸收,且吸收具有浓度依赖性,以被动吸收为主,Ver对红景天苷大鼠各肠吸收无影响,SDS促进了红景天苷回肠和结肠吸收。