Artificially controlling the solid-state precipitation in aluminum (Al) alloys is an efficient way to achieve well-performed properties,and the microalloying strategy is the most frequently adopted method for such a p...Artificially controlling the solid-state precipitation in aluminum (Al) alloys is an efficient way to achieve well-performed properties,and the microalloying strategy is the most frequently adopted method for such a purpose.In this paper,recent advances in lengthscale-dependent scandium (Sc) microalloying effects in Al-Cu model alloys are reviewed.In coarse-grained Al-Cu alloys,the Sc-aided Cu/Sc/vacancies complexes that act as heterogeneous nuclei and Sc segregation at the θ′-Al_(2)Cu/matrix interface that reduces interfacial energy contribute significantly to θ′precipitation.By grain size refinement to the fine/ultrafine-grained scale,the strongly bonded Cu/Sc/vacancies complexes inhibit Cu and vacancy diffusing toward grain boundaries,promoting the desired intragranular θ′precipitation.At nanocrystalline scale,the applied high strain producing high-density vacancies results in the formation of a large quantity of (Cu Sc,vacancy)-rich atomic complexes with high thermal stability,outstandingly improving the strength/ductility synergy and preventing the intractable low-temperature precipitation.This review recommends the use of microalloying technology to modify the precipitation behaviors toward better combined mechanical properties and thermal stability in Al alloys.展开更多
The mechanisms of oxide metallurgy include inducing the formation of intragranular acicular ferrite(IAF)using micron-sized inclusions and restricting the growth of prior austenite grains(PAGs)by nanosized particles du...The mechanisms of oxide metallurgy include inducing the formation of intragranular acicular ferrite(IAF)using micron-sized inclusions and restricting the growth of prior austenite grains(PAGs)by nanosized particles during welding.The chaotically oriented IAF and refined PAGs inhibit crack initiation and propagation in the steel,resulting in high impact toughness.This work summarizes the com-bined effect of deoxidizers and alloying elements,with the aim to provide a new perspective for the research and practice related to im-proving the impact toughness of the heat affected zone(HAZ)during the high heat input welding.Ti complex deoxidation with other strong deoxidants,such as Mg,Ca,Zr,and rare earth metals(REMs),can improve the toughness of the heat-affected zone(HAZ)by re-fining PAGs or increasing IAF contents.However,it is difficult to identify the specific phase responsible for IAF nucleation because ef-fective inclusions formed by complex deoxidation are usually multiphase.Increasing alloying elements,such as C,Si,Al,Nb,or Cr,con-tents can impair HAZ toughness.A high C content typically increases the number of coarse carbides and decreases the potency of IAF formation.Si,Cr,or Al addition leads to the formation of undesirable microstructures.Nb reduces the high-temperature stability of the precipitates.Mo,V,and B can enhance HAZ toughness.Mo-containing precipitates present good thermal stability.VN or V(C,N)is ef-fective in promoting IAF nucleation due to its good coherent crystallographic relationship with ferrite.The formation of the B-depleted zone around the inclusion promotes IAF formation.The interactions between alloying elements are complex,and the effect of adding dif-ferent alloying elements remains to be evaluated.In the future,the interactions between various alloying elements and their effects on ox-ide metallurgy,as well as the calculation of the nucleation effects of effective inclusions using first principles calculations will become the focus of oxide metallurgy.展开更多
First,strip cast samples of high strength microalloyed steel with sub-rapid solidification characteristics were prepared by simulated strip casting technique.Next,the isothermal growth of austenite grain during the re...First,strip cast samples of high strength microalloyed steel with sub-rapid solidification characteristics were prepared by simulated strip casting technique.Next,the isothermal growth of austenite grain during the reheating treatment of strip casts was observed in situ through confocal laser scanning microscope(CLSM).The results indicated that the time exponent of grains growth suddenly rise when the isothermal temperature higher than 1000℃.And the activation energy for austenite grain growth were calculated to be 538.0 kJ/mol in the high temperature region(above 1000℃)and 693.2 kJ/mol in the low temperature region(below 1000℃),respectively.Then,the kinetics model of austenite isothermal growth was established,which can predict the austenite grain size during isothermal hold very well.Besides,high density of second phase particles with small size was found during the isothermal hold at the low temperature region,leading to the refinement of austenite grain.After isothermal hold at different temperature for 1800 s,the bainite transformation in microalloyed steel strip was also observed in situ during the continuous cooling process.And growth rates of bainite plates with different nucleation positions and different prior austenite grain size(PAGS)were calculated.It was indicated that the growth rate of the bainite plate is not only related to the nucleation position but also to the PAGS.展开更多
We performed thermal simulation experiments of double-pass deformation of hypereutectoid rails with different microalloying elements at a cooling rate of 1℃/s and deformation of 80%to explore the influence of rare-ea...We performed thermal simulation experiments of double-pass deformation of hypereutectoid rails with different microalloying elements at a cooling rate of 1℃/s and deformation of 80%to explore the influence of rare-earth and microalloying elements on the structure of hypereutectoid rails and optimize the composition design of hypereutectoid rails.Scanning electron microscopy,transmission electron microscopy,X-ray diffraction,and other characterization techniques were employed to quantitatively analyzed the effects of different microalloying elements,including rare-earth elements,on pearlite lamellar spacing,cementite characteristics,and dislocation density.It was found that the lamellar spacing was reduced by adding various microalloying elements.Cementite lamellar thickness decreased with the refinement of pearlite lamellar spacing while the cementite content per unit volume increased.Local cementite spheroidization,dispersed in the ferrite matrix in granular form and thus playing the role of dispersion strengthening,was observed upon adding cerium(Ce).The contributions of dislocation density to the alloy strength of four steel sheet samples with and without the addition of nickel,Ce,and Ce–copper(Cu)composite were 26,27,32,and 37 MPa,respectively,indicating that the Ce–Cu composite had the highest dislocation strengthening effect.The Ce–Cu composite has played a meaningful role in the cementite characteristics and dislocation strengthening,which provides a theoretical basis for optimizing the composition design of hypereutectoid rails in actual production conditions.展开更多
Enhancing corrosion resistance of Mg-Zn alloys with high strength and low cost was critical for broadening their large-scale practical applications. Here we prepared solutionized, peak-and over-aged ZK60 alloys with a...Enhancing corrosion resistance of Mg-Zn alloys with high strength and low cost was critical for broadening their large-scale practical applications. Here we prepared solutionized, peak-and over-aged ZK60 alloys with and without microalloying Ca(0.26 wt.%) to explore the effects of nanoscale precipitates on their corrosion behavior in detail via experimental analyses and theoretical calculations. The results suggested the peak-aged ZK60 alloy with Ca addition showed improved corrosion resistance in comparison with the alloys without Ca,owing to the contribution of Ca on the refinement of precipitates and increase in their number density. Although the precipitates and Mg matrix formed micro-galvanic couples leading to dissolution, the fine and dense precipitates could generate “in-situ pinning” effect on the corrosion products, forming a spider-web-like structure and improving the corrosion inhibition ability accordingly. The pinning effect was closely related to the size and number density of precipitates. This study provided important insight into the design and development of advanced corrosion resistant Mg alloys.展开更多
The effect of Ti and Ce microalloying on the mechanical properties of Al-9Si-3.5Cu-0.2Zr-0.1Sr cast aluminum alloy was investigated,and it was hoped that the cast aluminum alloy with excellent comprehensive properties...The effect of Ti and Ce microalloying on the mechanical properties of Al-9Si-3.5Cu-0.2Zr-0.1Sr cast aluminum alloy was investigated,and it was hoped that the cast aluminum alloy with excellent comprehensive properties could be obtained.On the basis of Zr-Sr microalloyed cast aluminum alloy(Al-9Si-3.5Cu-0.2Zr-0.1Sr),the effects of 0.2Zr-0.1Sr-0.16Ti ternary microalloying and 0.2Zr-0.1Sr-0.16Ti-0.1Ce quaternary microalloying on the microstructure and properties of the alloy were investigated.The experimental results show that compared with Zr-Sr microalloying,Zr-Sr-Ti microalloying and Zr-Sr-Ti-Ce microalloying can effectively refine the microstructure,improve the modification effect of Si phase,and promote the improvement of Al_(2)Cu phase,thus improving the properties.The higher the degree of microalloying,the hardness is gradually increasing,but the electrical conductivity is gradually decreasing.Zr-Sr-Ti microalloying can increase the tensile strength of the alloy to 400.07 MPa and the elongation to 9.5%.Zr-Sr-Ti-Ce microalloying do not continue to improve the properties of the alloy,and the tensile strength and elongation after fracture decrease to a certain extent due to the addition of Ce.Therefore,the best comprehensive properties can be obtained by ZrSr-Ti microalloying(Al-9Si-3.5Cu-0.2Zr-0.1Sr-0.16Ti).展开更多
We report that the corrosion resistance of Mg is significantly improved by adding 0.05wt%Sc.Corrosion rates evaluated from weight loss values after room-temperature immersion in 0.6 M NaCl solution for two weeks were ...We report that the corrosion resistance of Mg is significantly improved by adding 0.05wt%Sc.Corrosion rates evaluated from weight loss values after room-temperature immersion in 0.6 M NaCl solution for two weeks were 0.27 and 4.0 mm y^(-1)for the high-purity Mg samples with and without microalloyed 0.05wt%Sc,respectively.The beneficial effect of Sc microalloying on the corrosion resistance of Mg is discussed in connection with Sc-induced microstructural modifications.展开更多
Dry sliding friction and wear test of Nb containing low carbon microalloyed steel was carried out at room temperature,and the effect of Nb on the wear behavior of the steel,as welll as the mechanism was studied.Scanni...Dry sliding friction and wear test of Nb containing low carbon microalloyed steel was carried out at room temperature,and the effect of Nb on the wear behavior of the steel,as welll as the mechanism was studied.Scanning electron microscopy(SEM) and energy dispersive spectrometry(EDS) were employed to analyze the morphology and composition of the worn surface,and the structure evolution of the plastic deformation layer.The carbide content and type in the steel were analyzed by the electrolytic extraction device and X-ray diffraction(XRD).The experimental results demonstrate that the addition of 0.2% Nb can refine the grain and generate Nb C to improve the wear resistance of the steel.By enhancing the load and speed of wear experiment,the wear mechanism of the test steel with 0.2% Nb changes from slight oxidation wear to severe adhesion wear and oxidation wear.Compared with the load,the increase in the rotation speed exerts a greater influence on the wear of the test steel.展开更多
The loading capacity of ultralarge container ships has reached 24000 TEUs so far,and to ensure the safe operation of these ships,the maxmium thickness of crack arrest steel used in the upper deck areas reaches 100 mm,...The loading capacity of ultralarge container ships has reached 24000 TEUs so far,and to ensure the safe operation of these ships,the maxmium thickness of crack arrest steel used in the upper deck areas reaches 100 mm,and crack arrest toughness(K_(ca))needs to be>8000 N/mm^(3)/2.The EH47 steel was employed to study the effect of Nb on the phase transformation of supercooled austenite in the continuous cooling process after rolling and the effect of Nb on microstructure and mechanical properties of the crack arrest steel plate.It was found that the addition of 0.02%Nb can inhibit the ferrite transformation,improve the steel plate strength,and reduce the strength inhomogeneity in the thickness direction.Industrial production of 100 mm-thick EH47 was carried out based on the function of Nb in EH47 steel,and the test results reveal that high-strength EH47 shipbuilding plates with high toughness,excellent fracture and crack arrest toughness,and good welding properties can be produced using Nb-microalloyed composition design and the thermal mechanical control process(TMCP);furthermore,the value of the crack arrest toughness reached 9450.7 N/mm^(3/2) at-10℃.展开更多
Deformation-induced ferrite transformation (DIFT) has been proved to be an effective approach to refine ferrite grains. This paper shows that the ferrite grains can further be refined through combination of DIFT and...Deformation-induced ferrite transformation (DIFT) has been proved to be an effective approach to refine ferrite grains. This paper shows that the ferrite grains can further be refined through combination of DIFT and V or V-N microalloying. Vanadium dissolved in γ matrix restrains DIFT. During deformation, vanadium carbonitrides rapidly precipitate due to strain-induced precipitation, which causes decrease in vanadium dissolved in matrix and indirectly accelerates DIFT. Under heavy deformation, deformation induced ferrite (DIF) grains in V microalloyed steel were finer than those in V free steel. The more V added to steel, the finer DIF grains obtained. Moreover, the addition of N to V microalloyed steels can remarkably accelerate precipitation of V, and then promote DIFT. However, DIF grains in V-N microalloyed steel easily coarsen.展开更多
The effect of trace addition of 0.2 wt.%Zn on the microstructures and mechanical properties of the age-hardening Mg-4.2Y-2.5Nd-1Gd-0.6Zr(wt.%)(WE43)alloy has been investigated.As compared with the WE43 alloy after sol...The effect of trace addition of 0.2 wt.%Zn on the microstructures and mechanical properties of the age-hardening Mg-4.2Y-2.5Nd-1Gd-0.6Zr(wt.%)(WE43)alloy has been investigated.As compared with the WE43 alloy after solid solution treatment at 525 ℃,the block-like Zn-Zr phase was still observed in the WE43-0.2Zn alloy.However,the time for WE43-0.2Zn alloy to get peak hardness at 250 ℃ was two hours,a half earlier than that in WE43 alloy,meaning a accelerated age precipitation kinetics has been achieved due to the addition of 0.2 wt.%Zn.Microalloyed with 0.2 wt.%Zn enhanced the ultimate tensile strength(UTS)slightly and ductility significantly both in the solutionized and peak aged condition.The enhancement in strength and ductility is possible associated with the larger volume fraction of precipitation phases due to a reduction of the solubility of rare earth elements(RE)in theα-Mg matrix,the larger aspect ratio(length to width)of precipitates and a decrease in stacking fault energy by addition of Zn.展开更多
The microstructure and the characteristics of the inclusions embedded in ferrite matrix in simulated coarse-grain heat affected zone (CGHAZ) of a Ti-Zr-treated high strength low alloy (HSLA) steel have been investigat...The microstructure and the characteristics of the inclusions embedded in ferrite matrix in simulated coarse-grain heat affected zone (CGHAZ) of a Ti-Zr-treated high strength low alloy (HSLA) steel have been investigated. The microstructure of the simulated CGHAZ dominantly consisted of intragranular acicular ferrite (IAF) combining with a small amount of polygonal ferrite (PF), widmanst tten ferrite (WF), bainite ferrite (BF), pearlite and martensite-austenite (M-A) islands. The PF, WF and BF were generally observed at the prior austenite grain boundaries and the interlocking acicular ferrite was usually found intragranularly. It was found that the inclusions were composed of Ti2O3, ZrO2, Al2O3 locating at the center of the particles and MnS lying on the surface layer of the inclusions. The intragranular complex inclusions promoted the acicular ferrite formation and the refinement of microstructure whilst those at prior austenite grain boundaries caused PF formation on the inclusions. The simulated CGHAZ consisting of such complicated microstructure exhibited desired mechanical properties.展开更多
The present work investigates the influences of microalloying with rare earths on the mechanical properties of magnesium alloys.The amount of each rare earth element is controlled below 0.4 wt.%in order not to increas...The present work investigates the influences of microalloying with rare earths on the mechanical properties of magnesium alloys.The amount of each rare earth element is controlled below 0.4 wt.%in order not to increase the cost of alloy largely.The synergic effects from the multi-microalloying with rare earths on the mechanical properties are explored.The obtained results show that the as-cast magnesium alloys multi-microalloying with rare earths possesses a quite high ductility with a tensile strain up to 25-30%at room temperature.Moreover,these alloys exhibit much better corrosion resistance than AZ31 alloy.The preliminary in situ neutron diffractions on the deformation of these alloys indicate that the multi-microalloying with rare earths seems to be beneficial for the activation of more slip systems.The deformation becomes more homogeneous and the resultant textures after deformation are weakened.展开更多
The microstractural evolution of microalloyed steel during hot forging process was investigated using physical simulation experiments. The dynamic recrystallized fraction was described by modifying Avrami's equation,...The microstractural evolution of microalloyed steel during hot forging process was investigated using physical simulation experiments. The dynamic recrystallized fraction was described by modifying Avrami's equation, the parameters of which were determined by single hit compression tests. Double hit compression tests were performed to model the equation describing the static recrystallized fraction, and the obtained predicted values were in good agreement with the measured values. Austenitic grain growth was modeled as: Dinc^5 = D0^5 + 1.6 × 10^32t·exp ( -716870/RT ) using isothermal tests. Furthermore, an equation describing the dynamic recrystallized grain size was given as Ddyn=3771·Z^-0.2. The models of microstructural evolution could be applied to the numerical simulation of hot forging.展开更多
The microstructural features and grain refinement in the coarse-grained region of the heat-affected zone in low-carbon high-strength microalloyed steels were investigated using optical microscopy, scanning electron mi...The microstructural features and grain refinement in the coarse-grained region of the heat-affected zone in low-carbon high-strength microalloyed steels were investigated using optical microscopy, scanning electron microscopy, and electron backscattering dif- fraction. The coarse-grained region of the heat-affected zone consists of predominantly bainite and a small proportion of acicular ferrite. Bainite packets are separated by high angle boundaries. Acicular ferrite laths or plates in the coarse-grained region of the heat-affected zone formed prior to bainite packets partition austenite grains into many smaller and separate areas, resulting in fine-grained mixed microstruc- tures. Electron backscattefing diffraction analysis indicates that the average crystallographic grain size of the coarse-grained region of the heat-affected zone reaches 6-9 μm, much smaller than that of anstanite grains.展开更多
Mg-0.5Bi-0.5Sn alloys with and without microalloying with 0.5 wt%Mn were subjected to extrusion,and the effect of Mn microalloying on the microstructural characteristic and corrosion behavior of the extruded alloys wa...Mg-0.5Bi-0.5Sn alloys with and without microalloying with 0.5 wt%Mn were subjected to extrusion,and the effect of Mn microalloying on the microstructural characteristic and corrosion behavior of the extruded alloys was investigated.The results indicated that the average grain size and the density of dislocations decreased,and a new Mg_(26.67)Mn_(65.47)Fe_(7.86)second phase as well as grain boundary segregation of Sn atoms could be observed in certain micro-regions of the extruded dilute Mg-0.5Bi-0.5Sn-0.5 Mn alloy.The tailoring of microstructure resulted in the significant enhancement in corrosion resistance(R_(p)increased from 1095.91Ωcm^(2)to 5008.79Ωcm^(2)).In addition,grain boundary segregation resulted in intergranular corrosion and led to the dissolution of Sn atoms.Hence,the dissolution rate of the matrix in Mg-0.5Bi-0.5Sn-0.5Mn alloy could be inhibited by the corrosion product film containing an intermediate product(SnO_(2)).展开更多
The influence of microalloying additions on the mechanical properties of a low-carbon cast steel containing combinations of V, Nb, and Ti in the as-cast condition was evaluated. Tensile and hardness test results indic...The influence of microalloying additions on the mechanical properties of a low-carbon cast steel containing combinations of V, Nb, and Ti in the as-cast condition was evaluated. Tensile and hardness test results indicated that good combinations of strength and ductility could be achieved by V and Nb additions. While the yield strength and UTS (ultimate tensile strength) increased up to the range of 378-435 MPa and 579- 590 MPa, respectively in the microalloyed heats, their total elongation ranged from 18% to 23%. The presence of Ti, however, led to some reduction in the strength. Microstructural studies including scanning electron microscopy (SEM) and optical microscopy revealed that coarse TiN particles were responsible for this behavior. The Charpy impact values of all compositions indicated that microalloying additions significantly decreased the impact energy and led to the dominance of cleavage facets on the fracture surfaces. It seems that the increase in the hardness of coarse ferrite grains due to the precipitation hardening is the main reason for brittle fracture.展开更多
A dilatometer was used to study the kinetics of bainite-to-austenite transformation in low carbon microalloyed steel with the initial microstructure of bainite during the continuous reheating process. The bainite-to-a...A dilatometer was used to study the kinetics of bainite-to-austenite transformation in low carbon microalloyed steel with the initial microstructure of bainite during the continuous reheating process. The bainite-to-austenite trans- formation was observed to take place in two steps at low heating rate. The first step is the dissolution of bainite, and the second one is the remaining bainite-to-austenite transformation controlled by a dissolution process. The calculation result of the kinetics of austenite formation shows that the two steps occur by diffusion at low heating rate. However, at high heating rate the bainite-to-austenite transformation occurs in a single step, and the process is mainly dominated by shear. The growth rate of austenite reaches the maximum at about 835℃ at different heating rates and the growth rate of austenite as a function of temperature increases with the increase in heating rate.展开更多
According to the misfitting dislocation theory,a method of theoretical calculation was devel- oped for the specific energy of the semicoherent interface between microalloy carbonitrides and austenite matrix.The calcul...According to the misfitting dislocation theory,a method of theoretical calculation was devel- oped for the specific energy of the semicoherent interface between microalloy carbonitrides and austenite matrix.The calculating formulae were derived and the results were satisfactorily applied on the research works.展开更多
The influences of Ca and Ce/La microalloying on the microstructure evolution and bio-corrosion resistances of extruded Mg-Zn alloys have been systematically investigated in the current study.Compared with single Ca or...The influences of Ca and Ce/La microalloying on the microstructure evolution and bio-corrosion resistances of extruded Mg-Zn alloys have been systematically investigated in the current study.Compared with single Ca or Ce/La addition,the Ca-Ce/La cooperative microalloying results in an outstanding grain refinement,because the fine secondary phase particles effectively hinder the recrystallized grain growth.The coarse Ca2Mg6Zn3 phases promote the formation of Ca3(PO4)2 or hydroxyapatite particles during the immersion process and accelerate the dissolution of the corrosion product film,which destroys its integrity and results in the deterioration of anti-corrosive performance.The Ce/La elements can be dispersed within the conventional Mg7Zn3 phases,which reduce the internal galvanic corrosion between Mg matrix and the secondary phases,leading to an obvious improvement of corrosion resistance.Therefore,the Ca-Ce/La cooperative microalloying achieves a homogenous fine-grained microstructure and improves the protective ability of surface film,which will pave a new avenue for the design of biomedical Mg alloys in the coming future.展开更多
基金supported by the National Natural Science Foundation of China(Nos.52201135,52271115,U23A6013,92360301,and U2330203)the 111 Project of China(No.BP2018008)+1 种基金the Shaanxi Province Innovation Team Project,China(No.2024RS-CXTD-58)supported by the International Joint Laboratory for Micro/Nano Manufacturing and Measurement Technologies and by the open research fund of Suzhou Laboratory。
文摘Artificially controlling the solid-state precipitation in aluminum (Al) alloys is an efficient way to achieve well-performed properties,and the microalloying strategy is the most frequently adopted method for such a purpose.In this paper,recent advances in lengthscale-dependent scandium (Sc) microalloying effects in Al-Cu model alloys are reviewed.In coarse-grained Al-Cu alloys,the Sc-aided Cu/Sc/vacancies complexes that act as heterogeneous nuclei and Sc segregation at the θ′-Al_(2)Cu/matrix interface that reduces interfacial energy contribute significantly to θ′precipitation.By grain size refinement to the fine/ultrafine-grained scale,the strongly bonded Cu/Sc/vacancies complexes inhibit Cu and vacancy diffusing toward grain boundaries,promoting the desired intragranular θ′precipitation.At nanocrystalline scale,the applied high strain producing high-density vacancies results in the formation of a large quantity of (Cu Sc,vacancy)-rich atomic complexes with high thermal stability,outstandingly improving the strength/ductility synergy and preventing the intractable low-temperature precipitation.This review recommends the use of microalloying technology to modify the precipitation behaviors toward better combined mechanical properties and thermal stability in Al alloys.
基金supported by the National Natural Science Foundation of China(No.U1960202).
文摘The mechanisms of oxide metallurgy include inducing the formation of intragranular acicular ferrite(IAF)using micron-sized inclusions and restricting the growth of prior austenite grains(PAGs)by nanosized particles during welding.The chaotically oriented IAF and refined PAGs inhibit crack initiation and propagation in the steel,resulting in high impact toughness.This work summarizes the com-bined effect of deoxidizers and alloying elements,with the aim to provide a new perspective for the research and practice related to im-proving the impact toughness of the heat affected zone(HAZ)during the high heat input welding.Ti complex deoxidation with other strong deoxidants,such as Mg,Ca,Zr,and rare earth metals(REMs),can improve the toughness of the heat-affected zone(HAZ)by re-fining PAGs or increasing IAF contents.However,it is difficult to identify the specific phase responsible for IAF nucleation because ef-fective inclusions formed by complex deoxidation are usually multiphase.Increasing alloying elements,such as C,Si,Al,Nb,or Cr,con-tents can impair HAZ toughness.A high C content typically increases the number of coarse carbides and decreases the potency of IAF formation.Si,Cr,or Al addition leads to the formation of undesirable microstructures.Nb reduces the high-temperature stability of the precipitates.Mo,V,and B can enhance HAZ toughness.Mo-containing precipitates present good thermal stability.VN or V(C,N)is ef-fective in promoting IAF nucleation due to its good coherent crystallographic relationship with ferrite.The formation of the B-depleted zone around the inclusion promotes IAF formation.The interactions between alloying elements are complex,and the effect of adding dif-ferent alloying elements remains to be evaluated.In the future,the interactions between various alloying elements and their effects on ox-ide metallurgy,as well as the calculation of the nucleation effects of effective inclusions using first principles calculations will become the focus of oxide metallurgy.
基金supported from the National Natural Science Foundation of China(No.52130408)the Hunan Scientific Technology Project,China(Nos.2019RS3007,2020WK2003)the Fundamental Research Funds for the Central Universities of Central South University,China。
文摘First,strip cast samples of high strength microalloyed steel with sub-rapid solidification characteristics were prepared by simulated strip casting technique.Next,the isothermal growth of austenite grain during the reheating treatment of strip casts was observed in situ through confocal laser scanning microscope(CLSM).The results indicated that the time exponent of grains growth suddenly rise when the isothermal temperature higher than 1000℃.And the activation energy for austenite grain growth were calculated to be 538.0 kJ/mol in the high temperature region(above 1000℃)and 693.2 kJ/mol in the low temperature region(below 1000℃),respectively.Then,the kinetics model of austenite isothermal growth was established,which can predict the austenite grain size during isothermal hold very well.Besides,high density of second phase particles with small size was found during the isothermal hold at the low temperature region,leading to the refinement of austenite grain.After isothermal hold at different temperature for 1800 s,the bainite transformation in microalloyed steel strip was also observed in situ during the continuous cooling process.And growth rates of bainite plates with different nucleation positions and different prior austenite grain size(PAGS)were calculated.It was indicated that the growth rate of the bainite plate is not only related to the nucleation position but also to the PAGS.
基金the National Natural Science Foundation of China(No.51361021)the Inner Mongolia Science and Technology Major Project(No.ZDZX2018024)。
文摘We performed thermal simulation experiments of double-pass deformation of hypereutectoid rails with different microalloying elements at a cooling rate of 1℃/s and deformation of 80%to explore the influence of rare-earth and microalloying elements on the structure of hypereutectoid rails and optimize the composition design of hypereutectoid rails.Scanning electron microscopy,transmission electron microscopy,X-ray diffraction,and other characterization techniques were employed to quantitatively analyzed the effects of different microalloying elements,including rare-earth elements,on pearlite lamellar spacing,cementite characteristics,and dislocation density.It was found that the lamellar spacing was reduced by adding various microalloying elements.Cementite lamellar thickness decreased with the refinement of pearlite lamellar spacing while the cementite content per unit volume increased.Local cementite spheroidization,dispersed in the ferrite matrix in granular form and thus playing the role of dispersion strengthening,was observed upon adding cerium(Ce).The contributions of dislocation density to the alloy strength of four steel sheet samples with and without the addition of nickel,Ce,and Ce–copper(Cu)composite were 26,27,32,and 37 MPa,respectively,indicating that the Ce–Cu composite had the highest dislocation strengthening effect.The Ce–Cu composite has played a meaningful role in the cementite characteristics and dislocation strengthening,which provides a theoretical basis for optimizing the composition design of hypereutectoid rails in actual production conditions.
基金the support of the National Natural Science Foundation of China (Grant Nos.51901174,52005389)the China Postdoctoral Science Foundation (Nos.2020M673383,2020M673389)the Fundamental Research Funds for the Central Universities (xzy012020001)。
文摘Enhancing corrosion resistance of Mg-Zn alloys with high strength and low cost was critical for broadening their large-scale practical applications. Here we prepared solutionized, peak-and over-aged ZK60 alloys with and without microalloying Ca(0.26 wt.%) to explore the effects of nanoscale precipitates on their corrosion behavior in detail via experimental analyses and theoretical calculations. The results suggested the peak-aged ZK60 alloy with Ca addition showed improved corrosion resistance in comparison with the alloys without Ca,owing to the contribution of Ca on the refinement of precipitates and increase in their number density. Although the precipitates and Mg matrix formed micro-galvanic couples leading to dissolution, the fine and dense precipitates could generate “in-situ pinning” effect on the corrosion products, forming a spider-web-like structure and improving the corrosion inhibition ability accordingly. The pinning effect was closely related to the size and number density of precipitates. This study provided important insight into the design and development of advanced corrosion resistant Mg alloys.
基金Funded by the Key Projects of Equipment Pre-research Foundation of the Ministry of Equipment Development of the Central Military Commission of China(No.6140922010201)the Key R&D Plan of Zhenjiang in 2018(No.GY2018021)。
文摘The effect of Ti and Ce microalloying on the mechanical properties of Al-9Si-3.5Cu-0.2Zr-0.1Sr cast aluminum alloy was investigated,and it was hoped that the cast aluminum alloy with excellent comprehensive properties could be obtained.On the basis of Zr-Sr microalloyed cast aluminum alloy(Al-9Si-3.5Cu-0.2Zr-0.1Sr),the effects of 0.2Zr-0.1Sr-0.16Ti ternary microalloying and 0.2Zr-0.1Sr-0.16Ti-0.1Ce quaternary microalloying on the microstructure and properties of the alloy were investigated.The experimental results show that compared with Zr-Sr microalloying,Zr-Sr-Ti microalloying and Zr-Sr-Ti-Ce microalloying can effectively refine the microstructure,improve the modification effect of Si phase,and promote the improvement of Al_(2)Cu phase,thus improving the properties.The higher the degree of microalloying,the hardness is gradually increasing,but the electrical conductivity is gradually decreasing.Zr-Sr-Ti microalloying can increase the tensile strength of the alloy to 400.07 MPa and the elongation to 9.5%.Zr-Sr-Ti-Ce microalloying do not continue to improve the properties of the alloy,and the tensile strength and elongation after fracture decrease to a certain extent due to the addition of Ce.Therefore,the best comprehensive properties can be obtained by ZrSr-Ti microalloying(Al-9Si-3.5Cu-0.2Zr-0.1Sr-0.16Ti).
基金supported by the National Research Foundation of Korea(NRF)grant funded by the Korea Government(MSIT)(No.2019R1A2C1003905)
文摘We report that the corrosion resistance of Mg is significantly improved by adding 0.05wt%Sc.Corrosion rates evaluated from weight loss values after room-temperature immersion in 0.6 M NaCl solution for two weeks were 0.27 and 4.0 mm y^(-1)for the high-purity Mg samples with and without microalloyed 0.05wt%Sc,respectively.The beneficial effect of Sc microalloying on the corrosion resistance of Mg is discussed in connection with Sc-induced microstructural modifications.
文摘Dry sliding friction and wear test of Nb containing low carbon microalloyed steel was carried out at room temperature,and the effect of Nb on the wear behavior of the steel,as welll as the mechanism was studied.Scanning electron microscopy(SEM) and energy dispersive spectrometry(EDS) were employed to analyze the morphology and composition of the worn surface,and the structure evolution of the plastic deformation layer.The carbide content and type in the steel were analyzed by the electrolytic extraction device and X-ray diffraction(XRD).The experimental results demonstrate that the addition of 0.2% Nb can refine the grain and generate Nb C to improve the wear resistance of the steel.By enhancing the load and speed of wear experiment,the wear mechanism of the test steel with 0.2% Nb changes from slight oxidation wear to severe adhesion wear and oxidation wear.Compared with the load,the increase in the rotation speed exerts a greater influence on the wear of the test steel.
文摘The loading capacity of ultralarge container ships has reached 24000 TEUs so far,and to ensure the safe operation of these ships,the maxmium thickness of crack arrest steel used in the upper deck areas reaches 100 mm,and crack arrest toughness(K_(ca))needs to be>8000 N/mm^(3)/2.The EH47 steel was employed to study the effect of Nb on the phase transformation of supercooled austenite in the continuous cooling process after rolling and the effect of Nb on microstructure and mechanical properties of the crack arrest steel plate.It was found that the addition of 0.02%Nb can inhibit the ferrite transformation,improve the steel plate strength,and reduce the strength inhomogeneity in the thickness direction.Industrial production of 100 mm-thick EH47 was carried out based on the function of Nb in EH47 steel,and the test results reveal that high-strength EH47 shipbuilding plates with high toughness,excellent fracture and crack arrest toughness,and good welding properties can be produced using Nb-microalloyed composition design and the thermal mechanical control process(TMCP);furthermore,the value of the crack arrest toughness reached 9450.7 N/mm^(3/2) at-10℃.
文摘Deformation-induced ferrite transformation (DIFT) has been proved to be an effective approach to refine ferrite grains. This paper shows that the ferrite grains can further be refined through combination of DIFT and V or V-N microalloying. Vanadium dissolved in γ matrix restrains DIFT. During deformation, vanadium carbonitrides rapidly precipitate due to strain-induced precipitation, which causes decrease in vanadium dissolved in matrix and indirectly accelerates DIFT. Under heavy deformation, deformation induced ferrite (DIF) grains in V microalloyed steel were finer than those in V free steel. The more V added to steel, the finer DIF grains obtained. Moreover, the addition of N to V microalloyed steels can remarkably accelerate precipitation of V, and then promote DIFT. However, DIF grains in V-N microalloyed steel easily coarsen.
基金This work was funded by the National Basic Research Program of China(973 Program)through project No.2013CB632202.
文摘The effect of trace addition of 0.2 wt.%Zn on the microstructures and mechanical properties of the age-hardening Mg-4.2Y-2.5Nd-1Gd-0.6Zr(wt.%)(WE43)alloy has been investigated.As compared with the WE43 alloy after solid solution treatment at 525 ℃,the block-like Zn-Zr phase was still observed in the WE43-0.2Zn alloy.However,the time for WE43-0.2Zn alloy to get peak hardness at 250 ℃ was two hours,a half earlier than that in WE43 alloy,meaning a accelerated age precipitation kinetics has been achieved due to the addition of 0.2 wt.%Zn.Microalloyed with 0.2 wt.%Zn enhanced the ultimate tensile strength(UTS)slightly and ductility significantly both in the solutionized and peak aged condition.The enhancement in strength and ductility is possible associated with the larger volume fraction of precipitation phases due to a reduction of the solubility of rare earth elements(RE)in theα-Mg matrix,the larger aspect ratio(length to width)of precipitates and a decrease in stacking fault energy by addition of Zn.
文摘The microstructure and the characteristics of the inclusions embedded in ferrite matrix in simulated coarse-grain heat affected zone (CGHAZ) of a Ti-Zr-treated high strength low alloy (HSLA) steel have been investigated. The microstructure of the simulated CGHAZ dominantly consisted of intragranular acicular ferrite (IAF) combining with a small amount of polygonal ferrite (PF), widmanst tten ferrite (WF), bainite ferrite (BF), pearlite and martensite-austenite (M-A) islands. The PF, WF and BF were generally observed at the prior austenite grain boundaries and the interlocking acicular ferrite was usually found intragranularly. It was found that the inclusions were composed of Ti2O3, ZrO2, Al2O3 locating at the center of the particles and MnS lying on the surface layer of the inclusions. The intragranular complex inclusions promoted the acicular ferrite formation and the refinement of microstructure whilst those at prior austenite grain boundaries caused PF formation on the inclusions. The simulated CGHAZ consisting of such complicated microstructure exhibited desired mechanical properties.
文摘The present work investigates the influences of microalloying with rare earths on the mechanical properties of magnesium alloys.The amount of each rare earth element is controlled below 0.4 wt.%in order not to increase the cost of alloy largely.The synergic effects from the multi-microalloying with rare earths on the mechanical properties are explored.The obtained results show that the as-cast magnesium alloys multi-microalloying with rare earths possesses a quite high ductility with a tensile strain up to 25-30%at room temperature.Moreover,these alloys exhibit much better corrosion resistance than AZ31 alloy.The preliminary in situ neutron diffractions on the deformation of these alloys indicate that the multi-microalloying with rare earths seems to be beneficial for the activation of more slip systems.The deformation becomes more homogeneous and the resultant textures after deformation are weakened.
基金This work was supported by the National Natural Science Foundation of China (No. 50275094).
文摘The microstractural evolution of microalloyed steel during hot forging process was investigated using physical simulation experiments. The dynamic recrystallized fraction was described by modifying Avrami's equation, the parameters of which were determined by single hit compression tests. Double hit compression tests were performed to model the equation describing the static recrystallized fraction, and the obtained predicted values were in good agreement with the measured values. Austenitic grain growth was modeled as: Dinc^5 = D0^5 + 1.6 × 10^32t·exp ( -716870/RT ) using isothermal tests. Furthermore, an equation describing the dynamic recrystallized grain size was given as Ddyn=3771·Z^-0.2. The models of microstructural evolution could be applied to the numerical simulation of hot forging.
基金supported by the National Natural Science Foundation of China (No.50734004)
文摘The microstructural features and grain refinement in the coarse-grained region of the heat-affected zone in low-carbon high-strength microalloyed steels were investigated using optical microscopy, scanning electron microscopy, and electron backscattering dif- fraction. The coarse-grained region of the heat-affected zone consists of predominantly bainite and a small proportion of acicular ferrite. Bainite packets are separated by high angle boundaries. Acicular ferrite laths or plates in the coarse-grained region of the heat-affected zone formed prior to bainite packets partition austenite grains into many smaller and separate areas, resulting in fine-grained mixed microstruc- tures. Electron backscattefing diffraction analysis indicates that the average crystallographic grain size of the coarse-grained region of the heat-affected zone reaches 6-9 μm, much smaller than that of anstanite grains.
基金jointly supported by the National Natural Science Foundation of China(Grant nos.:51704209,51701060)Natural Science Foundation of Shanxi Province(Grant no.:201801D121088)+2 种基金Shanxi Province Science Foundation for Youths(Grant no.:2016021063)Shanxi Scholarship Council of China(Grant no.:2019032)the Science and Technology Major Project of Shanxi Province(Grant nos.:20191102008,20191102007)。
文摘Mg-0.5Bi-0.5Sn alloys with and without microalloying with 0.5 wt%Mn were subjected to extrusion,and the effect of Mn microalloying on the microstructural characteristic and corrosion behavior of the extruded alloys was investigated.The results indicated that the average grain size and the density of dislocations decreased,and a new Mg_(26.67)Mn_(65.47)Fe_(7.86)second phase as well as grain boundary segregation of Sn atoms could be observed in certain micro-regions of the extruded dilute Mg-0.5Bi-0.5Sn-0.5 Mn alloy.The tailoring of microstructure resulted in the significant enhancement in corrosion resistance(R_(p)increased from 1095.91Ωcm^(2)to 5008.79Ωcm^(2)).In addition,grain boundary segregation resulted in intergranular corrosion and led to the dissolution of Sn atoms.Hence,the dissolution rate of the matrix in Mg-0.5Bi-0.5Sn-0.5Mn alloy could be inhibited by the corrosion product film containing an intermediate product(SnO_(2)).
文摘The influence of microalloying additions on the mechanical properties of a low-carbon cast steel containing combinations of V, Nb, and Ti in the as-cast condition was evaluated. Tensile and hardness test results indicated that good combinations of strength and ductility could be achieved by V and Nb additions. While the yield strength and UTS (ultimate tensile strength) increased up to the range of 378-435 MPa and 579- 590 MPa, respectively in the microalloyed heats, their total elongation ranged from 18% to 23%. The presence of Ti, however, led to some reduction in the strength. Microstructural studies including scanning electron microscopy (SEM) and optical microscopy revealed that coarse TiN particles were responsible for this behavior. The Charpy impact values of all compositions indicated that microalloying additions significantly decreased the impact energy and led to the dominance of cleavage facets on the fracture surfaces. It seems that the increase in the hardness of coarse ferrite grains due to the precipitation hardening is the main reason for brittle fracture.
文摘A dilatometer was used to study the kinetics of bainite-to-austenite transformation in low carbon microalloyed steel with the initial microstructure of bainite during the continuous reheating process. The bainite-to-austenite trans- formation was observed to take place in two steps at low heating rate. The first step is the dissolution of bainite, and the second one is the remaining bainite-to-austenite transformation controlled by a dissolution process. The calculation result of the kinetics of austenite formation shows that the two steps occur by diffusion at low heating rate. However, at high heating rate the bainite-to-austenite transformation occurs in a single step, and the process is mainly dominated by shear. The growth rate of austenite reaches the maximum at about 835℃ at different heating rates and the growth rate of austenite as a function of temperature increases with the increase in heating rate.
文摘According to the misfitting dislocation theory,a method of theoretical calculation was devel- oped for the specific energy of the semicoherent interface between microalloy carbonitrides and austenite matrix.The calculating formulae were derived and the results were satisfactorily applied on the research works.
基金the National Natural Science Foundation(Grant nos.5177117&51671152 and 51874225)the Key Research and Development Program of Shanxi Province(Grant nos.2020KWZ-007 and 2018ZDXMGY-149)the Youth Innovation Team of Shanxi Universities and the Natural Science Foundation of Jilin Province(Grant no.20180414016GH).
文摘The influences of Ca and Ce/La microalloying on the microstructure evolution and bio-corrosion resistances of extruded Mg-Zn alloys have been systematically investigated in the current study.Compared with single Ca or Ce/La addition,the Ca-Ce/La cooperative microalloying results in an outstanding grain refinement,because the fine secondary phase particles effectively hinder the recrystallized grain growth.The coarse Ca2Mg6Zn3 phases promote the formation of Ca3(PO4)2 or hydroxyapatite particles during the immersion process and accelerate the dissolution of the corrosion product film,which destroys its integrity and results in the deterioration of anti-corrosive performance.The Ce/La elements can be dispersed within the conventional Mg7Zn3 phases,which reduce the internal galvanic corrosion between Mg matrix and the secondary phases,leading to an obvious improvement of corrosion resistance.Therefore,the Ca-Ce/La cooperative microalloying achieves a homogenous fine-grained microstructure and improves the protective ability of surface film,which will pave a new avenue for the design of biomedical Mg alloys in the coming future.