The interface properties of Fe(101)/zinc silicate modified by organo-siloxane(KH-570)was studied by using the method of molecular dynamics simulation.By calculating the temperature and energy fluctuation of equilibriu...The interface properties of Fe(101)/zinc silicate modified by organo-siloxane(KH-570)was studied by using the method of molecular dynamics simulation.By calculating the temperature and energy fluctuation of equilibrium state,equilibrium concentration distribution,MSD of layer and different groups,and interaction energy of two interface models,the influencing mechanism on the interface properties of adding organosiloxane into coating system was studied at the atomic scale.It shows that the temperature and energy of interface oscillated in a small range and it was exited in a state of dynamic equilibrium within the initial simulation stage(t<20 ps).It can be seen from the multiple peak states of concentration distribution that the iron substrate,organo-siloxane and zinc silicate are distributed in the form of a concentration gradient in the real environment.The rapid diffusion of free zinc powder in zinc silicate coating was the essential reason that affected the comprehensive properties of coating.The interface thickness decreased from 7.45 to 6.82Å,the MSD of free zinc powder was effectively reduced,and the interfacial energy was increased from 104.667 to 347.158 kcal/mol after being modified by organo-siloxane.展开更多
For the further design of the particular gearbox components, the alternating cycles of the respective application mean an often insufficient knowledge of the actual loads occuring in use. Especially for the applicatio...For the further design of the particular gearbox components, the alternating cycles of the respective application mean an often insufficient knowledge of the actual loads occuring in use. Especially for the application within lifting units, such dynamic load cycles are very difficult to pre-estimate. The so-called slack rope test represents the most critical point in the load cycle and provides a special challenge for the gearbox design. Because of this missing expert knowledge, a test bench of such an application is installed and applied to practical movement cycles. Besides the test bench, a multi-body simulation model of the whole system is mapped within the MBS （multi-body simulation） environment SIMPACK. To verify this simulation model, the results are compared with the respective measurements of the test bench. These comparisons show very good agreements. Thus, one of the major advantages of using such simulation tools is the possibility to re-evaluate the internal and external loads during the whole design process. Finally, these simulations serve as a clarification of the load spectrum of the different drivetrain components. Gearbox series or different modifications of the design can now be analyzed prospectively without extensive testing.展开更多
Factors that affect blasting results may be grouped into those factors that can be controlled and those that cannot be controlled. The controllable factors include explosive properties, initiation timing, and blast ge...Factors that affect blasting results may be grouped into those factors that can be controlled and those that cannot be controlled. The controllable factors include explosive properties, initiation timing, and blast geometry. The uncontrollable factors comprise the rock’s natural structures, such as joints and fractures, and the properties, such as elastic constants, density and strength. Among these, the influence of rock structural planes often contributes a high degree of variability to blasting results. This paper presents a theoretical analysis of rock structural plane influences on smooth blasting results based on elasticity and stress wave propagation theory with an emphasis on smooth blasting techniques. Two types of simulated experiments in lab (using strain and acoustic emission measurements) are used to verify the theoretical analysis. The results show that it is difficult to achieve smooth blasting results when the angle between the natural rock structural planes and the blast induced fracture planes ranges from 10° to 60°. Among these angles, 30° is the least desirable angle to produce a smooth wall. For angles less than 10° and greater than 60°, the influence of rock structural planes on blasting results can be ignored.展开更多
In order to study the dynamic behaviour of construction,specifically seismic response of structures,as many researchers did,we have resorted to modelling methods,based on the scaled internal forces.Therefore,this rese...In order to study the dynamic behaviour of construction,specifically seismic response of structures,as many researchers did,we have resorted to modelling methods,based on the scaled internal forces.Therefore,this research includes results of an experimental investigation aimed to establish the possibility of realistic simulations of the cyclic response of small-scale models of one bay,one-storey reinforced concrete frames with masonry infills as a preliminary step for simulating the dynamic response of such structural.So,the specimens constructed were 1:9 scale R/C frames.These 1:9 scale infill frames were constructed with prototype materials and were tested in an extensive experimental sequence representing specimens of a scale near the prototype(1:3).The tested laboratory models include 1:3 scale infilled R/C frames that were built from original material such as steel,concrete and masonry infills(hollow masonry units and mortar).With the same scale,geometry and construction materials used for the construction of a 1:3 scale 5-story three dimensional building.This program consisted of 16 models,5 bare and 11 masonry infilled.all models refer to single-storey one-bay 1:9 scale as for the original structure and a one third of the scale(1:3)as for the prototype(1:3).The reinforced concrete specimens were designed in such a way as to prevent shear failure of the columns.Finally,the present paper was carried out in the Laboratory of Strength of Materials and Structures in the Department of Civil Engineering at Aristotle University of Thessaloniki.展开更多
校核、验证与确认(verification,validation,and accreditation,VV&A)是保证仿真模型可信度的关键手段,其中模型验证是核心环节。针对导弹飞行仿真模型结果验证存在的参考数据不可获得、参考数据来源多样、专家验证主观性强等问题,...校核、验证与确认(verification,validation,and accreditation,VV&A)是保证仿真模型可信度的关键手段,其中模型验证是核心环节。针对导弹飞行仿真模型结果验证存在的参考数据不可获得、参考数据来源多样、专家验证主观性强等问题,提出一种基于时间序列分段特征提取的导弹飞行仿真模型结果验证方法。提出了一种综合的时间序列分段线性方法,由基于二阶导数提取趋势边缘点的线性分段算法和基于极值点优化的Top-Down线性分段算法两部分组成,以实现对导弹飞行仿真数据和参考数据进行有效的线性分段表示。基于上述分段结果,对各段时间序列的均值、方差、斜率等特征进行提取,以辅助专家进行验证,从而降低验证中的主观性;或者直接利用TIC系数法、动态时间规整(dynamic time warping,DTW)等方法进行客观的相似性分析。通过充分利用时间序列的分段特征,可实现各种情形下的导弹飞行仿真模型结果验证。通过一个导弹模型结果验证案例演示了所提方法的可行性和有效性。展开更多
目的分析内分泌科临床实习带教中应用基于结果导向教育(Based on the Results-oriented Education,OBE)理念下模拟医学教学方式的应用效果。方法选取2022年2月—2023年2月滕州市中心人民医院内分泌科的80名临床实习生为研究对象,根据不...目的分析内分泌科临床实习带教中应用基于结果导向教育(Based on the Results-oriented Education,OBE)理念下模拟医学教学方式的应用效果。方法选取2022年2月—2023年2月滕州市中心人民医院内分泌科的80名临床实习生为研究对象,根据不同教学模式分为研究组、参照组,每组40名,研究组采取OBE理念下模拟医学教学方式,参照组采取传统教学,比较两组实习前后思维能力、学习投入度以及考核成绩。结果实习后,研究组思维能力各项评分均高于参照组,差异有统计学意义(P均<0.05)。实习后,研究组学习投入度各项评分均高于参照组,差异有统计学意义(P均<0.05)。研究组理论成绩为(92.93±1.88)分、实践考核成绩为(95.67±0.55)分,均高于参照组的(88.24±1.93)分、(87.24±0.61)分,差异有统计学意义(t=11.009、64.913,P均<0.05)。结论OBE理念下模拟医学教学方式应用在内分泌科临床实习带教中可提升学生的学习思维能力。展开更多
基金supported by the National Science Fundation of China(No.U1937601),and the National Natural Science Foundation of China(Grant No.NSFC51905471).
文摘The interface properties of Fe(101)/zinc silicate modified by organo-siloxane(KH-570)was studied by using the method of molecular dynamics simulation.By calculating the temperature and energy fluctuation of equilibrium state,equilibrium concentration distribution,MSD of layer and different groups,and interaction energy of two interface models,the influencing mechanism on the interface properties of adding organosiloxane into coating system was studied at the atomic scale.It shows that the temperature and energy of interface oscillated in a small range and it was exited in a state of dynamic equilibrium within the initial simulation stage(t<20 ps).It can be seen from the multiple peak states of concentration distribution that the iron substrate,organo-siloxane and zinc silicate are distributed in the form of a concentration gradient in the real environment.The rapid diffusion of free zinc powder in zinc silicate coating was the essential reason that affected the comprehensive properties of coating.The interface thickness decreased from 7.45 to 6.82Å,the MSD of free zinc powder was effectively reduced,and the interfacial energy was increased from 104.667 to 347.158 kcal/mol after being modified by organo-siloxane.
文摘For the further design of the particular gearbox components, the alternating cycles of the respective application mean an often insufficient knowledge of the actual loads occuring in use. Especially for the application within lifting units, such dynamic load cycles are very difficult to pre-estimate. The so-called slack rope test represents the most critical point in the load cycle and provides a special challenge for the gearbox design. Because of this missing expert knowledge, a test bench of such an application is installed and applied to practical movement cycles. Besides the test bench, a multi-body simulation model of the whole system is mapped within the MBS （multi-body simulation） environment SIMPACK. To verify this simulation model, the results are compared with the respective measurements of the test bench. These comparisons show very good agreements. Thus, one of the major advantages of using such simulation tools is the possibility to re-evaluate the internal and external loads during the whole design process. Finally, these simulations serve as a clarification of the load spectrum of the different drivetrain components. Gearbox series or different modifications of the design can now be analyzed prospectively without extensive testing.
文摘Factors that affect blasting results may be grouped into those factors that can be controlled and those that cannot be controlled. The controllable factors include explosive properties, initiation timing, and blast geometry. The uncontrollable factors comprise the rock’s natural structures, such as joints and fractures, and the properties, such as elastic constants, density and strength. Among these, the influence of rock structural planes often contributes a high degree of variability to blasting results. This paper presents a theoretical analysis of rock structural plane influences on smooth blasting results based on elasticity and stress wave propagation theory with an emphasis on smooth blasting techniques. Two types of simulated experiments in lab (using strain and acoustic emission measurements) are used to verify the theoretical analysis. The results show that it is difficult to achieve smooth blasting results when the angle between the natural rock structural planes and the blast induced fracture planes ranges from 10° to 60°. Among these angles, 30° is the least desirable angle to produce a smooth wall. For angles less than 10° and greater than 60°, the influence of rock structural planes on blasting results can be ignored.
文摘In order to study the dynamic behaviour of construction,specifically seismic response of structures,as many researchers did,we have resorted to modelling methods,based on the scaled internal forces.Therefore,this research includes results of an experimental investigation aimed to establish the possibility of realistic simulations of the cyclic response of small-scale models of one bay,one-storey reinforced concrete frames with masonry infills as a preliminary step for simulating the dynamic response of such structural.So,the specimens constructed were 1:9 scale R/C frames.These 1:9 scale infill frames were constructed with prototype materials and were tested in an extensive experimental sequence representing specimens of a scale near the prototype(1:3).The tested laboratory models include 1:3 scale infilled R/C frames that were built from original material such as steel,concrete and masonry infills(hollow masonry units and mortar).With the same scale,geometry and construction materials used for the construction of a 1:3 scale 5-story three dimensional building.This program consisted of 16 models,5 bare and 11 masonry infilled.all models refer to single-storey one-bay 1:9 scale as for the original structure and a one third of the scale(1:3)as for the prototype(1:3).The reinforced concrete specimens were designed in such a way as to prevent shear failure of the columns.Finally,the present paper was carried out in the Laboratory of Strength of Materials and Structures in the Department of Civil Engineering at Aristotle University of Thessaloniki.
文摘校核、验证与确认(verification,validation,and accreditation,VV&A)是保证仿真模型可信度的关键手段,其中模型验证是核心环节。针对导弹飞行仿真模型结果验证存在的参考数据不可获得、参考数据来源多样、专家验证主观性强等问题,提出一种基于时间序列分段特征提取的导弹飞行仿真模型结果验证方法。提出了一种综合的时间序列分段线性方法,由基于二阶导数提取趋势边缘点的线性分段算法和基于极值点优化的Top-Down线性分段算法两部分组成,以实现对导弹飞行仿真数据和参考数据进行有效的线性分段表示。基于上述分段结果,对各段时间序列的均值、方差、斜率等特征进行提取,以辅助专家进行验证,从而降低验证中的主观性;或者直接利用TIC系数法、动态时间规整(dynamic time warping,DTW)等方法进行客观的相似性分析。通过充分利用时间序列的分段特征,可实现各种情形下的导弹飞行仿真模型结果验证。通过一个导弹模型结果验证案例演示了所提方法的可行性和有效性。
文摘目的分析内分泌科临床实习带教中应用基于结果导向教育(Based on the Results-oriented Education,OBE)理念下模拟医学教学方式的应用效果。方法选取2022年2月—2023年2月滕州市中心人民医院内分泌科的80名临床实习生为研究对象,根据不同教学模式分为研究组、参照组,每组40名,研究组采取OBE理念下模拟医学教学方式,参照组采取传统教学,比较两组实习前后思维能力、学习投入度以及考核成绩。结果实习后,研究组思维能力各项评分均高于参照组,差异有统计学意义(P均<0.05)。实习后,研究组学习投入度各项评分均高于参照组,差异有统计学意义(P均<0.05)。研究组理论成绩为(92.93±1.88)分、实践考核成绩为(95.67±0.55)分,均高于参照组的(88.24±1.93)分、(87.24±0.61)分,差异有统计学意义(t=11.009、64.913,P均<0.05)。结论OBE理念下模拟医学教学方式应用在内分泌科临床实习带教中可提升学生的学习思维能力。
