Recent Advances in Interface Modification of Cu/graphite Composites and Layered Ternary Carbides of Modified Layer Candidate

We review the fundamental properties and significant issues related to Cu/graphite composites.In particular,recent research on the interfacial modification of Cu/graphite composites is addressed,including the metal-modified layer,carbide-modified layer,and combined modified layer.Additionally,we propose the use of ternary layered carbide as an interface modification layer for Cu/graphite composites.

Influence of Sb modification on microstructures and mechanical properties of Mg2 Si/AM60 composites

The refining effect and mechanism of Sb on Mg2Si and the microstructure of the matrix were investigated.The results indicate that there are Mg3Sb2 particles in the composites with the addition of Sb,and Mg3Sb2 can promote the formation of fine polygonal type Mg2Si by providing nucleation site.Meanwhile,the grain size of Sb modified alloy is finer than that of the matrix. The improved microstructure results in the improvement of mechanical properties.The ultimate tensile strength is increased by 12.2%with the addition of 0.8%Sb.

Effects of Mierostructure Modification on Properties of MN/BN Composites

It is very difficult to prepare full-densified aluminum nitride-boron nitride （AIN/BN） composite ceramics with homogeneous microstructure and high thermal conductivity. Spark plasma sintering （SPS） was used to fully densify the AIN/BN composites in this work. Microstructure, mechanical properties and thermal conductivity of the SPS sintered AIN/BN composites with 5-30 vol% BN were investigated. The results show that the microstructure of composites is fine and homogenous, and the AIN/BN composites exhibit high mechanical properties. To promote the growth of AIN grains and modify the distribution of grain boundary in AIN/BN composites, a heat treating methodology was introduced through gas pressure sintering （GPS）. This processing was significantly beneficial to enhancing the thermal conductivity of the specimen. The thermal conductivity of AIN/BN composites with 5-30 vol% BN reached 60 W/m K after the samples were treated by GPS.

Study of the Superficial Modification of Sisal Fibres with Lignin, and Its Use As a Reinforcement Agent in Cementitious Composites

The objective of this work was to evaluate different superficial treatments of sisal fibres employing lignin,and their use as a reinforcement agent in cementitious composites.The treatments consisted of superficially impregnating sisal fibres(S)with organosolv lignin(LO),organosolv lignin and glutaraldehyde(LOG),Kraft lignin(LK)and Kraft lignin and glutaraldehyde(LKG).The fibre modifications were verified by FTIR-ATR and SEM analyzes,and the presence of lignin on the surface of the fibres was evidenced,confirming the effectiveness of the treatments.The mechanical,thermal(by TGA)and water absorption properties of the fibres before and after the modifications were also investigated.After treatment,the modified fibres presented an expressive reduction of the water absorption and did not show significant changes in the mechanical properties when compared with the natural unmodified sisal fibre(SNAT).It was verified an increase in the thermal stability of the treated fibres which can be attributed to the insertion of lignin on the fibres.To evaluate the performance of the fibres in the cementitious composites,cement plates(CP)were produced with different treated fibres(CP-SLOG,CP-SLO,CP-SLKG,CP-SLK)and fibres without treatment(CP-SNAT).The composites were evaluated concerning to the water absorption,porosity and mechanical properties.The fractured regions were also investigated by SEM.All composites prepared showed similar values of absorption and porosity indexes.From the mechanical properties,the composites prepared with modified fibres showed a significant increase in the modulus of rupture and modulus of elasticity compared with CP-SNAT,while toughness was similar to all samples.From the SEM images,it was observed that the modified fibres immersed in the cementitious plates showed no degradation,indicating that the impregnation of lignin acted as a protective agent of the fibres.Therefore,the treatments of the fibres with lignin led to a significant improvement in the properties of the composites generating a treatment with potential for industrial application.

Direct Electrochemistry and Electrocatalysis of Hemoglobin at PAMAM Dendrimer-MWNTs-Au Nanoparticles Composite Film Modified Glassy Carbon Electrode

The direct electron transfer of hemoglobin at the PAMAM-MWNTs-AuNPs composite film modified glassy carbon electrode was studied. In a phosphate buffer solution（PBS, pH=7.0）, the formal potential（E^0） of Hb was -0.105 V versus SCE, the electron transfer rate constant was 4.66 s-1. E^0＇ of Hb at the modified electrode was linearly varied in a pH range of 5.0-8.0 with a slope of-49.2 mV/pH. The Hb/PAMAM-MWNTs-AuNPs/GCE gave an excellent electrocatalytic response to the reduction of hydrogen peroxide. The catalytic current increased linearly with H2O2 concentration in a range of 1.0× 10^-6 to 2.2× 10^-3 mol/L. The detection limit was 2.0× 10^-7 mol/L at a signal to noise ratio of 3. The Michaelis-Menten constant（Km^app） was 2.95 mmol/L.

Control of Fracture Behavior of Carbon Fiber/Pitch-based CarbonMatrix Composites with Microspace Modification Concept

Theoretical consideration was conducted on a relation between pore diameter and interfacialarea between pores and fibers when pores uniforinly distribute in C/C composites. It was shownthat bonding at the fiber/matrix interface apparently decreased with decreasing a pore diameter,and consequently a new idea of microspace modification concept was proposed for controllingfracture behavior of C/C composites. Four types of C/C composites with various pore structureswere fabricated by hot-pressing, and their fracture behavior was investigated by three pointbending tests. The fracture behavior of the C/C composites was changed from brittle one topseudo ductile one with decreasing the pore diameter. This result supported the validity of themicrospace modification concept proposed in this paper.

Effects of RE,V,Ti and B composite modification on the microstructure and properties of high chromium cast iron containing 3% molybdenum

The effects of RE, V, Ti and B on the microstructure and properties of high chromium cast iron containing 3% molybdenum under as-cast and heat treatment conditions were investigated with the method of comparing experiments. The results show that with the increase of RE content, the primary austenite of high chromium cast iron is obviously refined. The morphology of carbide is changed from netlike and lath to small multiangular isolated blocks or massive blocks, the isolated degree of carbide is improved obviously, and the size is significantly refined. The addition of V and B into high chromium cast iron can refine the microstmcture, reduce coarse columnar crystals and make the carbide smaller and uniform. Through composite modification with RE, V, Ti and B, the hardness, wear resistance and impact toughness of high chromium cast iron are increased conspicuously. After heat treatment, the hardness of high chromium iron is increased significantly, but the toughness and wear resistance do not show great improvement.

Intumescent Flame-retardant Modification of Polypropylene/Carbon Fiber Composites

To improve the flame resistance of polypropylene(PP)/carbon fiber(CF)composite materials,triazine char-forming agent(TCA)was compounded with ammonium polyphosphate(APP)or modified APP(CS-APP)in a 2:1 ratio to prepare intumescent flame retardant(IFR)and the modified intumescent flame retardant(CS-IFR)in this paper.Flame retardancy and thermal degradation behaviors of the composites modified by IFR and CS-IFR were characterized by Fourier Transform Infrared(FTIR),contact angle measurement,oxygen index(OI),vertical burning tests(UL-94),thermogravimetric analyer(TGA),and thermogravimetric analyzer coupled with Fourier transform infrared(TG-FTIR).It was found that 25.0 phr of IFR and 24.0 phr of CS-IFR could improve the LOI value of PP/CF composites to 28.3%and 28.9%,respectively.At the same time,a UL-94 V-0 rating was achieved.The experimental results show that the IFR and CS-IFR prepared could effectively improve the flame retardancy and thermostability of PP/CF composites,and they would greatly expand the application range of PP/CF composite materials.

Preparation of defect free ceramic/Ti composite membranes by surface modification and in situ oxidation

Al2O3 ceramic powder was applied to modify the large pores defects on the surface of the porous metal Ti support,in situ oxidation method was a convenient method to prepare defect free ceramic/Ti composite membranes on this basis.In situ oxidation conditions experimental results show that the best condition for preparing the TiO2-Al2O3/Ti composite membrane is under 800°C for 2 h,and the microstructure and pore sizes of the TiO2-Al2O3/Ti composite membranes are affected obviously.The thickness and composition of the TiO2/Ti composite membranes are determined by SEM and XRD completely.The pore size distribution of the composite membrane is measured by bubble pressure method,the most probable aperture is about 3.12μm,while the average pore size of defect free TiO2-Al2O3/Ti is about 3.23μm.After ultrasonic treatment,the slight weight change of membranes reveals no observable change,which indicates that TiO2-Al2O3/Ti composite membranes maintain a good stability.

A New Modification to Shear Lag Model as Applied to Stiffness and Yield Strength of Short Fiber Reinforced Metal Matrix Composites

A new modification for the shear lag model is given and the expressions for the stiffness and yield Strength of short fiber metal matri×composite are derived. These expressions are then compared with our experimental data in a SiCw/Al-Li T6 composite and the published experimental data on different SiCw/Al T6 composites and also compared with the previous shear lag models and the other theoretical models.

Effect of Nano-silica Modification on the Tensile Property of SMA/GF/CF/Epoxy Super Hybrid Woven Fabric Composites

Tensile properties of epoxy casts together with shape memory alloy（SMA）, glass（GF） and carbon（CF） woven fabric reinforced epoxy matrix super hybrid composites were investigated, respectively. In order to enhance the mechanical strength of this advanced material, two categories of modifications including matrix blending and fiber surface coating by nano-silica were studied. Scanning electron microscopy（SEM） and fiber pull-out tests were adopted to complement the experimental results, respectively. Experimental results reveal that the toughness of epoxy matrix is enhanced significantly by adding 2 wt% nano-silica. The failure mechanism of SMA reinforced hybrid composites is different from that of GF/CF/epoxy composites. Compared with the matrix modification, the fibers modified by coating nano-silica on the surface have better tensile performances. Moreover, the fiber pull-out test results also indicate that composites with fiber surface modification have better interfacial performances. The modification method used in this paper can help to enhance the tensile performance of the mentioned composite materials in real engineering fields.

Improving the Dispersion and Integration of Multi-Walled Carbon Nanotubes in PolyvinyI-Alcohol Composite Thin Film through Surface Modification

The article investigated the influence of modification process parameters on dispersity of MWNTs DI （in deionized） water and PVA/MWNT composite＇s electrical conductivity. Experimental results obtained by SEM （scanning electron microscope）, TEM （transmission electron microscope）, transform Fourier infrared spectroscopy, pH meter confirmed the most effective conditions in modifying the MWNT surface at the 1：3 mixture of nitric and sulfuric acid at 60 ℃. The extinction coefficient value of functionalized MWNTs at 500 nm wavelength was determined to be 41.24 cm^2·mg^-1, while their dispersibility in DI water was about 12.85 mg/mL and stable in more than 3 weeks via UV-vis spectroscopy. The other important result is the decrease of volume resistivity from 7.98 × 10^6 MΩ·m ofPVA （polyvinyl alcohol） to 4.15 × 10^4 MΩ·m of PVA/1 wt% modified MWNT thin film.

Effect of mixed rare earth oxides and CaCO_3 modification on the microstructure of an in-situ Mg_2Si/Al-Si composite

The effects of mixed rare earth oxides and CaCO3 on the microstructure of an in-situ Mg2Si/Al-Si hypereutectic alloy composite were investigated by optical microscope,scanning electron microscope,and energy dispersive spectrum analysis. The results showed that the morphol-ogy of the primary Mg2Si phase particles changed from irregular or crosses to polygonal shape,their sizes decreased from 75 μm to about 25 μm,and the compound of both the oxide and CaCO3 was better than either the single mixed rare earth o...

Cure of a New Type Composite on Noise Control and Effect of Filler Modification

A new type composite of high efficiency sound attenuation was cured. The superfine tungsten powder, plasticizerand stabilizer are added into the PVC resin and blended in the mixing chamber of a HAAKE rheometer. The effect ofthe filler modification is considered in the composite cure. The properties of modified composite and unmodified oneare studied by SEM morphology viewing, acoustic and mechanical measurement. The test results indicate that thereason of the better soundproof and mechanical properties is the particle uniform dispersion and stronger adhesion.

Effect of Na3AlF6 Addition and Surface Modification of SiCp on the Microstructure and Mechanical Properties of SiCp/Al Composites

Al-matrix composites reinforced with 56.5 vol% SiC were prepared by powder metallurgy with different amounts of additives and surface modifications of SiCp. The crystalline phase, morphology, elements on the surface of SiCp and the interface between SiCp and Al were characterized by XRD, SEM, EDS and EPMA. The results show that it is favorable for the reaction between TiO2-C on the surface of SiCp and Al at the SiCp-Al interface at 1 050 ℃. Besides, the process of Na3 AlF6 melting, dissolving and then contacting with Al2 O3 formed the NaF-AlF3-Al2 O3 system, which generated OAlF2-, promoting the dessolution of Al2 O3 film on the surface of Al powder. Na3 AlF6 meets the needs of chemical reaction in TiO2-C-Al system at the SiCpAl interface in the way of offering more molten Al. After 0.75 wt% Na3 AlF6 was added into raw materials, the whole TiO2-C film and most SiO2 film were destroyed and the interfacial bonding between SiCp and Al was keeping good, in which no obvious void and crack were observed. Meanwhile, no brittle Al4 C3 phase formed in the system. At this time, the flexure strength and density of samples presented optimal values, reaching up to 106.5 MPa and 90.77% respectively.

Surface Modification of Nanometer TiO_2 and Effect of Preparing TiO_2/P(St-co-DVB) Composites by Dispersion Polymerization

Surface modification of nanometer titanium dioxide particles and effect of preparing TiO2/P （St-co-DVB） composites by dispersion polymerization are described. To introduce vinyl group onto the surface of titanium dioxide particles, the titanium dioxide particles were surface-modified with a silicane coupling agent, methacryloylpropyltrimethoxysilicane. Polymer encapsulation in the presence of either modified-titanium dioxide particles or unmodified-titanium dioxide particles was carried out by dispersion polymerization of styrene, divinylbenzene in ethanol medium with polyvinylpyrroliclone as stabilizer, and 2, 2＇-azobis（isobutyronitrile） as initiator. The modified-titanium dioxide was analyzed with Fourier-transform infrared spectroscopy（FTIR）, UV-Vis spectrophotometer, thermo-gravimetric analysis and transmission microscope. The polymer encapsulation of modified-titanium dioxide and unmodified-titanium dioxide particles was confirmed with FTIR and transmission electron microscope. Results show that compared with unmodified-titanium dioxide, modified-titanium dioxide is more suitable for preparing inorganic core/orclanic shell composites.

The Studies on the Surface Organic Modification of Tourmaline Powder with Stearic Acid and Its Composite

Stearic acid modified tourmaline powder had been investigated to improve the compatibility and dispersed stability between tourmaline and polymer matrix. The experimental results indicated that the activation index was 100% and contact angle reached 120° when the ratio of the ore slurry is 5:50, the dosage of stearic acid and p-toluenesulfonic acid is 10% and 0.5% (of tourmaline powder’s quantity) respectively with reaction at 80°C for 6.0 h, and the modified tourmaline exhibited an excellent hydrophobic property. The introduction of stearic groups reduced the reunion of tourmaline particles clearly and improved the dispersivity in polymers, and the amount of negative ions released of modified tourmaline increased obviously for both modified tourmaline powders and its composite with polyamide-66 compared to the unmodified tourmaline. Moreover, the structure of modified tourmaline was also characterized by means of Fourier Transform infrared spectroscopy, X-ray diffraction, thermal gravimetric analysis, scanning electron microscope.

Research progress in friction stir processing of magnesium alloys and their metal matrix surface composites: Evolution in the 21^(st )century

Rising concerns about climate change drive the demand for lightweight components.Magnesium(Mg)alloys are highly valued for their low weight,making them increasingly important in various industries.Researchers focusing on enhancing the characteristics of Mg alloys and developing their Metal Matrix Composites(MMCs)have gained significant attention worldwide over the past decade,driven by the global shift towards lightweight materials.Friction Stir Processing(FSP)has emerged as a promising technique to enhance the properties of Mg alloys and produce Mg-MMCs.Initially,FSP adapted to refine grain size from the micro to the nano level and accelerated the development of MMCs due to its solid-state nature and the synergistic effects of microstructure refinement and reinforcement,improving strength,hardness,ductility,wear resistance,corrosion resistance,and fatigue strength.However,producing defect-free and sound FSPed Mg and Mg-MMCs requires addressing several variables and their interdependencies,which opens up a broad range of practical applications.Despite existing reviews on individual FSP of Mg,its alloys,and MMCs,an attempt has been made to analyze the latest research on these three aspects collectively to enhance the understanding,application,and effectiveness of FSP for Mg and its derivatives.This review article discusses the literature,classifies the importance of Mg alloys,provides a historical background,and explores developments and potential applications of FSPed Mg alloys.It focuses on novel fabrication methods,reinforcement strategies,machine and tool design parameters,material characterization,and integration with other methods for enhanced properties.The influence of process parameters and the emergence of defects are examined,along with specific applications in mono and hybrid composites and their microstructure evolution.The study identifies promising reinforcement materials and highlights research gaps in FSP for Mg alloys and MMCs production.It concludes with significant recommendations for further exploration,reflecting ongoing advancements in this field.

Microstructure Regulation and Combustion Performance Optimization of PVDF/Al Composite Powder by Non-covalent Functionalized Graphenes

Graphene prepared by non-covalent modification of sulfonated poly(ether-ether-ketone)(SPG)was combined with polyvinylidene fluoride(PVDF)/Al to improve the PVDF/Al thermal conductivity while reducing the effect of the thermal resistance at the graphene-polymer interface.The regulation rule of SPG with different contents on the energy release of fluorine-containing system was studied.When the content of SPG is 4%,the peak pressure and rise rate of SPG/PVDF/Al composite powder during ignition reach the maximum of 4845.28 kPa and 8683.58 kPa/s.When the content of SPG is 5%,the PVDF/Al composite powder is completely coated by SPG,and the calorific value of the material reachs the maximum of 29.094 kJ/g.Through the design and micro-control of the composite powder,the calorific value of the material can be effectively improved,but the improvement of the mass release rate still depends on the graphene content and surface modification state.

Study on Modification of Waste Rubber Powder in Cement-Based Composites Mixed with Waste Rubber Powder

In view of the disadvantage that the mechanical properties of cement-based composites can be significantly reduced by incorporating waste rubber powder in situ, the surface modification methods of the original rubber powder by coupling agent KH560, sodium hydroxide, polyvinyl alcohol (PVA), methyl hydroxyethyl cellulose ether (MHEC) and tetraethyl orthosilicate (TEOS) as precursors were adopted respectively. The modification of waste rubber powder was studied by Change rate of mortar strength of cement-based composite mortar mixed with waste rubber powder. The results show that the hybrid modification method using tetraethyl orthosilicate as precursor has better ef-fect. When 5 phr ethyl orthosilicate is added, the compressive strength and flexural strength of cement-based composite mortar can be increased by 31.7% and 28%. Scanning electron microscopy (SEM) results show that the surface of waste rubber powder with good modification effect has many pro-trusions and flake-like porous structures which are beneficial to its bonding with cement-based materials.