The dynamic recrystallization and static recrystallization in a low carbon steel were investigated through single-pass and double-pass experiments. The results indicate that as the deformation temperature increases an...The dynamic recrystallization and static recrystallization in a low carbon steel were investigated through single-pass and double-pass experiments. The results indicate that as the deformation temperature increases and the strain rate decreases, the shape of the stress-strain curve is changed from dynamic recovery shape to dynamic recrystallization shape. The austenite could not recrystallize within a few seconds after deformation at temperature below 900 ℃. According to the change in microstructure during deformation, the controlled rolling of low carbon steel can be divided into four stages： dynamic recrystallization, dynamic recovery, strain-induced ferrite transformation, and rolling in two-phase region. According to the microstructure after deformation, the controlled rolling of low carbon steel can be divided into five regions： non-recrystallized austenite, partly-recrystallized austenite, fully-recrystallized austenite, austenite to ferrite transformation, and dual phase.展开更多
A low carbon steel was used to determine the critical strain εc for completion of deformation enhanced ferrite transformation （DEFT） through a series of hot compression tests. In addition, the influence of prior au...A low carbon steel was used to determine the critical strain εc for completion of deformation enhanced ferrite transformation （DEFT） through a series of hot compression tests. In addition, the influence of prior austenite grain size （PAGS） on the critical strain was systematically investigated. Experimental results showed that the critical strain is affected by PAGS. When γ→α transformation completes, the smaller the PAGS is, the smaller the critical strain is. The ferrite grains obtained through DEFT can be refined to about 3 μm when the DEFT is completed.展开更多
Microstructure of metastable austenitic manganese steel after reverse transformation treatment was investi gated using optical microscopy, X ray diffraction （XRD）, electrical resistivity and hardness testing. Austen...Microstructure of metastable austenitic manganese steel after reverse transformation treatment was investi gated using optical microscopy, X ray diffraction （XRD）, electrical resistivity and hardness testing. Austenite grain refinement was successfully achieved by a two-step heat treatment. First, martensite was produced by cooling the so- lution-treated samples to --196 ℃. Then, the deep cryogenic treated samples were heated to 850 ℃ upon slow or rapid heating. The mean size of original austenite grain was about 400 fire. But the mean size of equiaxed reversion austenite was refined to 50 μm. Microstructure evolution and electrical resistivity change showed that martensite plates underwent tempering action upon slow heating, and the residual austenite was decomposed, resulting in the formation of pearlite nodules at the austenite grains boundaries. The refinement mechanism upon slow heating is the diffusion-controlled nucleation and growth of austenite. However, the reverse transformation upon rapid heating was predominated by displacive manner. The residual austenite was not decomposed. The plate α-phase was carbon-super- saturated until the starting of reverse transformation. The reverse transformation was accompanied by surface effect, resulting in the formation of plate austenite with high density dislocations. The refinement mechanism upon rapid heating is the recrystallization of displacive reversed austenite.展开更多
基金Item Sponsored by High Technology Development Programof China (2001AA332020) and National Natural ScienceFoundation of China (50271015)
文摘The dynamic recrystallization and static recrystallization in a low carbon steel were investigated through single-pass and double-pass experiments. The results indicate that as the deformation temperature increases and the strain rate decreases, the shape of the stress-strain curve is changed from dynamic recovery shape to dynamic recrystallization shape. The austenite could not recrystallize within a few seconds after deformation at temperature below 900 ℃. According to the change in microstructure during deformation, the controlled rolling of low carbon steel can be divided into four stages： dynamic recrystallization, dynamic recovery, strain-induced ferrite transformation, and rolling in two-phase region. According to the microstructure after deformation, the controlled rolling of low carbon steel can be divided into five regions： non-recrystallized austenite, partly-recrystallized austenite, fully-recrystallized austenite, austenite to ferrite transformation, and dual phase.
基金This work was financially supported by the National Science and Technology Ministry to the research project ‘Advanced industriali-zation technique of manufacture for carbon steel of 500 MPa grade’ (No.2001AA332020).
文摘A low carbon steel was used to determine the critical strain εc for completion of deformation enhanced ferrite transformation （DEFT） through a series of hot compression tests. In addition, the influence of prior austenite grain size （PAGS） on the critical strain was systematically investigated. Experimental results showed that the critical strain is affected by PAGS. When γ→α transformation completes, the smaller the PAGS is, the smaller the critical strain is. The ferrite grains obtained through DEFT can be refined to about 3 μm when the DEFT is completed.
基金Sponsored by National Natural Science Foundation of China(51071075)
文摘Microstructure of metastable austenitic manganese steel after reverse transformation treatment was investi gated using optical microscopy, X ray diffraction （XRD）, electrical resistivity and hardness testing. Austenite grain refinement was successfully achieved by a two-step heat treatment. First, martensite was produced by cooling the so- lution-treated samples to --196 ℃. Then, the deep cryogenic treated samples were heated to 850 ℃ upon slow or rapid heating. The mean size of original austenite grain was about 400 fire. But the mean size of equiaxed reversion austenite was refined to 50 μm. Microstructure evolution and electrical resistivity change showed that martensite plates underwent tempering action upon slow heating, and the residual austenite was decomposed, resulting in the formation of pearlite nodules at the austenite grains boundaries. The refinement mechanism upon slow heating is the diffusion-controlled nucleation and growth of austenite. However, the reverse transformation upon rapid heating was predominated by displacive manner. The residual austenite was not decomposed. The plate α-phase was carbon-super- saturated until the starting of reverse transformation. The reverse transformation was accompanied by surface effect, resulting in the formation of plate austenite with high density dislocations. The refinement mechanism upon rapid heating is the recrystallization of displacive reversed austenite.
