SIMULATION OF STRATA MOVEMENTS DUE TO UNDERGROUND MINING USING AN AUTOMATED MEASUREMENT SYSTEM FOR EQUIVALENT MATERIAL MODELING FACILITY

Strata movement simulation was conducted in an equivalent material modeling facility developed by the Department of Mining Engineering, Southern Illinois University at Carbondale, under U. S. Bureau of Mines contracts. An innovative displacement measurement system called videogrammetric system was developed and utilized for recording, measuring and analyzing the deformation and failure process of the models. A room and pillar mining and a longwall mining prototypes were studied in the modeling. Study found that weak floor of coal seam plays an important role in pillar stability and therefore the overburden movements.

STUDY ON JOINING PROCESS FOR LAMINATED OBJECT MANUFACTURING USING METALAS MODELING MATERIALS

In order to solve some key problems associated with the rapid manufacturingof metallic functional part, a new technique using vacuum solid-state pressure diffusion weldingprocess to join the metallic slice sheets is put forward. The following results can be drawn fromthe experiments: only 1 percent shrinkage happened in the stack direction and it came from theregular system error. The atoms diffuse between joint interfaces clearly and new grains formedmeanwhile. The average shear strength of welding zone is more than 100 MPa and micro hardness ofwelding zone is almost the same as that of matrix. It is shown from above results that the vacuumsolid-state pressure diffusion welding process is an available technique to join metal slice sheetsfor the rapid manufacturing of metallic functional parts.

MODELING OF LASER MACHINING ON POLYMETHYL METHACRYLATE TO FABRICATE MICROFLUIDIC CHIP

The use of a CO2 laser system for fabrication of microfluidic chip on polymethyl methacrylate （PMMA） is presented to reduce fabrication cost and time of chip. The grooving process of the laser system and a model for the depth of microchannels are investigated. The relations between the depth of laser-cut channels and the laser beam power, velocity or the number of passes of the beam along the same channel are evaluated. In the experiments, the laser beam power varies from 0 to 50 W, the laser beam scanning velocity varies from 0 to 1 000 mm/s and the passes vary in the range of 1 to 10 times. Based on the principle of conservation of energy, the influence of the laser beam velocity, the laser power and the number of groove passes are examine. Considering the grooving interval energy loss, a modified mathematical model has been obtained and experimental data show good agreement with the theoretical model. This approach provides a simple way of predicting groove depths. The system provides a cost alternative of the other methods and it is especially useful on research work of rnicrofluidic prototyping due to the short cycle time of production.

Material Removal Model Considering Influence of Curvature Radius in Bonnet Polishing Convex Surface

The bonnet tool polishing is a novel, advanced and ultra-precise polishing process, by which the freeform surface can be polished. However, during the past few years, not only the key technology of calculating the dwell time and controlling the surface form in the bonnet polishing has been little reported so far, but also little attention has been paid to research the material removal function of the convex surface based on the geometry model considering the influence of the curvature radius. Firstly in this paper, for realizing the control of the freeform surface automatically by the bonnet polishing, on the basis of the simplified geometric model of convex surface, the calculation expression of the polishing contact spot on the convex surface considering the influence of the curvature radius is deduced, and the calculation model of the pressure distribution considering the influence of the curvature radius on the convex surface is derived by the coordinate transformation. Then the velocity distribution model is built in the bonnet polishing the convex surface. On the basis of the above research and the semi-experimental modified Preston equation obtained from the combination method of experimental and theoretical derivation, the material removal model of the convex surface considering the influence of the curvature radius in the bonnet polishing is established. Finally, the validity of the model through the simulation method has been validated. This research presents an effective prediction model and the calculation method of material removal for convex surface in bonnet polishing and prepares for the bonnet polishing the free surface numerically and automatically.

Mesoscopic Modeling Approach and Application for Steel Fiber Reinforced Concrete under Dynamic Loading:A Review

Steel fiber reinforced concrete(SFRC)has drawn extensive attention in recent years for its superior mechanical response to dynamic and impact loadings.Based on the existing test results,the highstrength steel fibers embedded in a concrete matrix usually play a strong bridging effect to enhance the bonding force between fiber and the matrix,and directly contribute to the improvement of the post-cracking behavior and residual strength of SFRC.To gain a better understanding of the action behavior of steel fibers in matrix and further capture the failure mechanism of SFRC under dynamic loads,the mesoscopic modeling approach that assumes SFRC to be composed of different mesoscale phases(i.e.,steel fibers,coarse aggregates,mortar matrix,and interfacial transition zone(ITZ))has been widely employed to simulate the dynamic responses of SFRC material and structural members.This paper presents a comprehensive review of the state-of-the-art mesoscopic models and simulations for SFRC under dynamic loading.Generation approaches for the SFRC mesoscale model in the simulation works,including steel fiber,coarse aggregate,and the ITZ between them,are reviewed and compared systematically.The material models for different phases and the interaction relationship between fiber and concrete matrix are summarized comprehensively.Additionally,some example applications for SFRC under dynamic loads(i.e.,compression,tension,and contact blast)simulated using the general mesoscale models are given.Finally,some critical analysis on the current shortcomings of the mesoscale modeling of SFRC is highlighted,which is of great significance for the future investigation and development of SFRC.

Fatigue analysis of closed-cell aluminium foam using different material models

The fatigue analyses of AlSi7 closed-cell aluminium foam were performed using a real porous model and three different homogenised material models:crushable foam model,isotropic hardening model and kinematic hardening model.The numerical analysis using all three homogenised material models is based on the available experimental results previously determined from fatigue tests under oscillating tensile loading with the stress ratio R=0.1.The obtained computational results have shown that both isotropic and kinematic hardening models are suitable to analyse the fatigue behaviour of closed-cell aluminium foam.Besides,the kinematic hardening material model has demonstrated significantly shorter simulation time if compared to the isotropic hardening material model.On the other hand,the crushable foam model is recognized as an inappropriate approach for the fatigue analyses under tension loading conditions.

Deformation Stability of GH4033 Superalloy in the Hot Continuous Rolling Process Based on Dynamic Material Model and Finite Element Model

The flow stress behavior of GH4033 superalloy was determined by the hot compression tests at the temperatures of 1223-1473 K and the total strains of 0.6 with the strain rates of 0.001-30.0 s^(-1) by using cylindrical samples.The processing maps based on the dynamic material model(DMM)combined with the corresponding microstructure observations indicate the reasonable processing domain locating at the strain rates of 0.1-1.0 s^(-1) and the deformation temperature of 1273-1423 K.Meanwhile,the numerical simulation based on finite element model(FEM)described the variation of the effective strain,effective strain rate and the temperature for the core node,and unveiled the influence of the hot rolling parameters considering the initial temperature(T_(0))range of 1223-1473 K and the first-stand biting velocity(v_(0))range of 0.15-0.35 m·s^(-1).Furthermore,the deformation stability of GH4033 superalloy in the round rod hot continuous rolling(HCR)process is described and analyzed by coupling the three-dimensional(3-D)processing map,and the spatial trajectory lines were determined by the numerically simulated temperatures,the strains and the strain rates.Finally,the results show that the hot deformation stability of GH4033 can be achieved by the rolling process parameters located at T_(0)=1423 K and v_(0)=0.25 m·s^(-1).Additionally,the practical HCR processes as T_(0)=1423 K and v_(0)=0.15,0.25,0.35 m·s^(-1) were operated to verify the influence of the hot rolling parameters on the hot deformation stability by the microstructure observation of the final products.

Finite Element Simulation of Flexible Roll Forming with Supplemented Material Data and the Experimental Verification

Flexible roll forming is a promising manufacturing method for the production of variable cross section products. Considering the large plastic strain in this forming process which is much larger than that of uniform deformation phase of uniaxial tensile test, the widely adopted method of simulating the forming processes with non-supplemented material data from uniaxial tensile test will certainly lead to large error. To reduce this error, the material data is supplemented based on three constitutive models. Then a finite element model of a six passes flexible roll forming process is established based on the supplemented material data and the original material data from the uniaxial tensile test. The flexible roll forming experiment of a B pillar reinforcing plate is carried out to verify the proposed method. Final cross section shapes of the experimental and the simulated results are compared. It is shown that the simulation calculated with supplemented material data based on Swift model agrees well with the experimental results, while the simulation based on original material data could not predict the actual deformation accurately. The results indicate that this material supplement method is reliable and indispensible, and the simulation model can well reflect the real metal forming process. Detailed analysis of the distribution and history of plastic strain at different positions are performed. A new material data supplement method is proposed to tackle the problem which is ignored in other roll forming simulations, and thus the forming process simulation accuracy can be greatly improved.

Multi-Material Topology Optimization of Structures Using an Ordered Ersatz Material Model

This paper proposes a new element-based multi-material topology optimization algorithm using a single variable for minimizing compliance subject to a mass constraint.A single variable based on the normalized elemental density is used to overcome the occurrence of meaningless design variables and save computational cost.Different from the traditional material penalization scheme,the algorithm is established on the ordered ersatz material model,which linearly interpolates Young’s modulus for relaxed design variables.To achieve a multi-material design,the multiple floating projection constraints are adopted to gradually push elemental design variables to multiple discrete values.For the convergent element-based solution,the multiple level-set functions are constructed to tentatively extract the smooth interface between two adjacent materials.Some 2D and 3D numerical examples are presented to demonstrate the effectiveness of the proposed algorithm and the possible advantage of the multi-material designs over the traditional solid-void designs.

Elasto-plastic analysis of masonry with anisotropic plastic material model

This paper establishes an anisotropic plastic material model to analyze the elasto-plastic behavior of masonry in plane stress state.Being an anisotropic material,masonry has different constitutive relation and fracture energies along each orthotropic axes.Considering the unique material properties of masonry,a new yield criterion for masonry is proposed combining the Hill's yield criterion and the Rankine's yield criterion.The new yield criterion not only introduces compression friction coefficient of shear but also considers yield functions for independent stress state along two material axes of tension.To solve the involved nonlinear equations in numerical analysis,several nonlinear methods are implemented,including Newton-Raphson method for nonlinear equations and Implicit Euler backward mapping algorithm to update stresses.To verify the proposed material model of masonry,a series of tests are operated.The simulation results show that the new developed material model implements successfully.Compared with isotropic material model,the proposed model performs better in elasto-plastic analysis of masonry in plane stress state.The proposed anisotropic model is capable of simulating elasto-plastic behavior of masonry and can be used in related applications.

Correlation between Single Factor Material Constitutive Model Parameters and Temperature for Ti6Al4V Alloy

Accurate material constitutive model is considered highly necessary to perform finite element simulation and analysis.However,it is difficult to establish the material constitutive model because of uncertainty of mathematical relationship and constraint of existing experimental condition.At present,there exists considerable gap between finite element simulation result and actual cutting process.Particular emphases were put on investigating the correlation between ＂single factor＂ material constitutive model parameters and temperature for Ti6Al4V alloy,and also establishment of material constitutive model for this kind of material.Theoretical analyses based on dislocation theory and material functional relations showed that material model was deeply affected by variation temperature.By the least squares best fit to the available quasi-static and high-speed impact compression experiment data,material parameters at various temperatures were found.Experimental curves analyses and material parameters comparison showed that the ＂single factor＂ material constitutive model parameters were temperature dependent.Using the mathematical mapping between material parameters and temperature,＂single factor＂ material constitutive model of Ti6Al4V alloy was established,which was proven to be right by comparing with experimental measurements.This work makes clear that the ＂single factor＂ material constitutive model parameters of Ti6Al4V alloy are temperature dependent.At the same time,an accurate material constitutive model is established,which helps to optimize cutting process and control machining distortion for Ti6Al4V alloy aerospace parts.

Development of Mathematical Model on Preparation of Functionally Graded Material by Co-sedimentation

From the process of sedimentation the mathematical relationships among deposition Volume and powder properties as well as sedimentation parameters were deduced. Based on the formula a mathematical model was set up and simulated through the computer. At last the validity of mathematical model was supported by the representative experiment on Ti-Mo system FGM prepared by co-sedimentation.

Hybrid graded element model for transient heat conduction in functionally graded materials

This paper presents a hybrid graded element model for the transient heat conduction problem in functionally graded materials （FGMs）. First, a Laplace transform approach is used to handle the time variable. Then, a fundamental solution in Laplace space for FGMs is constructed. Next, a hybrid graded element is formulated based on the obtained fundamental solution and a frame field. As a result, the graded properties of FGMs are naturally reflected by using the fundamental solution to interpolate the intra-element field. Further, Stefest＇s algorithm is employed to convert the results in Laplace space back into the time-space domain. Finally, the performance of the proposed method is assessed by several benchmark examples. The results demonstrate well the efficiency and accuracy of the proposed method.

Thermal-stress induced phenomena in two-component material:part I

The paper deals with analytical fracture mechanics to consider elastic thermal stresses acting in an isotropic multi-particle-matrix system. The multi-particle-matrix system consists of periodically distributed spherical particles in an infinite matrix. The thermal stresses originate during a cooling process as a consequence of the difference αm - αp in thermal expansion coefficients between the matrix and the particle, αm and αp, respectively. The multi-particle-matrix system thus represents a model system applicable to a real two-component material of a precipitation-matrix type. The infinite matrix is imaginarily divided into identical cubic cells. Each of the cubic cells with the dimension d contains a central spherical particle with the radius R, where d thus corresponds to inter-particle distance. The parameters R, d along with the particle volume fraction v = v（R, d） as a function of R, d represent microstructural characteristics of a twocomponent material. The thermal stresses are investigated within the cubic cell, and accordingly are functions of the microstructural characteristics. The analytical fracture mechanics includes an analytical analysis of the crack initiation and consequently the crack propagation both considered for the spherical particle （q = p） and the cell matrix （q = m）. The analytical analysis is based on the determination of the curve integral Wcq of the thermal-stress induced elastic energy density Wq. The crack initiation is represented by the determination of the critical particle radius Rqc = Rqc（V）. Formulae for Rqc are valid for any two-component mate- rial of a precipitate-matrix type. The crack propagation for R 〉 Rqc is represented by the determination of the function fq describing a shape of the crack in a plane perpendicular

Evolution and Development of the Information Concept in Biological Systems: From Empirical Description to Informational Modeling of the Living Structures

With the purpose to smooth the way of a correct understanding of information concepts and their evolution,in this paper,is discussed the evolution and development of the concept of information in biological systems,showing that this concept was intuitively perceived even since ancient times by our predecessors,and described according to their language level of that times,but the crystallization of the real meaning of information is an achievement of our nowadays,by successive contribution of various scientific branches and personalities of the scientific community of the world,leading to a modern description/modeling of reality,in which information plays a fundamental role.It is shown that our reality can be understood as a contribution of matter/energy/information and represented/discussed as the model of the Universal Triangle of Reality(UTR),where various previous models can be suggestively inserted,as a function of their basic concern.The modern concepts on information starting from a theoretic experiment which would infringe the thermodynamics laws and reaching the theory of information and modern philosophic concepts on the world structuration allow us to show that information is a fundamental component of the material world and of the biological structures,in correlation with the structuration/destructuration processes of matter,involving absorption/release of information.Based on these concepts,is discussed the functionality of the biologic structures and is presented the informational model of the human body and living structures,as a general model of info-organization on the entire biological scale,showing that a rudimentary proto-consciousness should be operative even at the low-scale biological systems,because they work on the same principles,like the most developed bio-systems.The operability of biologic structures as informational devices is also pointed out.

Selective ensemble modeling based on nonlinear frequency spectral feature extraction for predicting load parameter in ball mills

Strong mechanical vibration and acoustical signals of grinding process contain useful information related to load parameters in ball mills. It is a challenge to extract latent features and construct soft sensor model with high dimensional frequency spectra of these signals. This paper aims to develop a selective ensemble modeling approach based on nonlinear latent frequency spectral feature extraction for accurate measurement of material to ball volume ratio. Latent features are first extracted from different vibrations and acoustic spectral segments by kernel partial least squares. Algorithms of bootstrap and least squares support vector machines are employed to produce candidate sub-models using these latent features as inputs. Ensemble sub-models are selected based on genetic algorithm optimization toolbox. Partial least squares regression is used to combine these sub-models to eliminate collinearity among their prediction outputs. Results indicate that the proposed modeling approach has better prediction performance than previous ones.

An Elastic-Plastic Iceberg Material Model Considering Temperature Gradient Effects and its Application to Numerical Study

To simulate the FPSO-iceberg collision process more accurately, an elastic-plastic iceberg material model considering temperature gradient effects is proposed and applied. The model behaves linearly elastic until it reaches the ‘Tsai-Wu’ yield surfaces, which are a series of concentric elliptical curves of different sizes. Decreasing temperature results in a large yield surface. Failure criteria, based on the influence of accumulated plastic strain and hydrostatic pressure, are built into the model. Based on published experimental data on the relationship between depth and temperature in icebergs, three typical iceberg temperature profiles are proposed. According to these, ice elements located at different depths have different temperatures. The model is incorporated into LS-DYNA using a user-defined subroutine and applied to a simulation of FPSO collisions with different types of icebergs. Simulated area-pressure curves are compared with design codes to validate the iceberg model. The influence of iceberg shape and temperature on the collision process is analyzed. It is indicated that FPSO structural damage not only depends on the relative strength between the iceberg and the structure, but also depends on the local shape of the iceberg.

Establishment and Analysis on Material Flow Model in Argo-animal Husbandry Ecosystem

This paper analyzed the material flow situation in argo-animal husbandry ecosystem by compartment model. This model was an important mean for investigating the whole structural characteristics in ecosystem. Based on this analysis, characteristics of material cycle and integrity in the system were mastered. As an example of natural conditions in Yonghe Village, Shuangcheng Township, Shuangeheng Municipal, Heilongjang Province, the system of linear differential equations in system was established by extracting each compartment and investigating material flow and stability of this model was proved by Lyapunov linear theory. The result showed that this system could not be interfered by initial value in the state of present, input and output.

A Virtual Work Approach to Modeling the Nonlinear Behavior of Steel Frames

The stiffness reduction is studied in detail of compact W-Shapes （wide-flange steel shapes） that results from yielding of the cross-section due to uniaxial bending and axial compression. Three-dimensional m-p-τ surface plots developed from detailed fiber element models of a W8x31 are used to develop a generalized material model for direct implementation in the virtual work method. A portal steel frame is used to illustrate the virtual work method with the nonlinear material model in a first-order, inelastic analysis implementation and in a second-order, inelastic analysis condition. The nonlinear modeling capabilities of MASTAN2 are used to verify the accuracy of the virtual work results and are found to be in very close agreement.

Beam Element Material Model for Rotary-Straightened Steel W-Shapes

An inelastic material model that was previously developed by the author for standard W-Shapes was adapted for use to model the behavior and strength of rotary-straightened hot rolled W-Shape sections.Using a published residual stress model for these W-Shapes,limit load analyses were conducted using the material model in MASTAN2 and were compared with published finite element results.The material model required an adjustment to the initial yield moment conditions and residual stress ratios.Comparisons with published results indicate that these minor modifications were sufficient to provide very good modeling agreement.The previously developed material model can be used effectively to model the limit load conditions of rotary-straightened hot rolled W-Shape beams and beam-columns in steel frames.The effect of rotary-straightening W-Shapes is more significant for minor axis bending conditions and this becomes more pronounced as the floor load magnitudes increase.