Detonation Propagation Characteristics of Superposition Explosive Materials

In order to investigate detonation propagation characteristics of different charge patterns,the detonation velocities of superposition strip shaped charges made up of a detonating cord and explosives were measured by a detonation velocity measuring instrument under conditions of different ignition.The experimental results and theoretical analysis show that the maximum detonation propagation velocity depends on the explosive materials with the maximum velocity among all the explosive materials.Using detonating cord in a superposition charge can shorten detonation propagation time and improve the efficiency of explosive energy.The measurement method of detonation propagation velocity and experimental results are presented and investigated.

Measurement of the echo reduction for underwater acoustic passive materials by using the time reversal technique

A measuring method of the echo reduction of passive materials by using the time reversal（TR） technique is presented. To measure the echo reduction of a sample with this approach, the received signals are firstly focused according to the TR theory. Then, the sample is removed and the TR processing is again employed to realize the focus of the received signal.Finally, the echo reduction of the sample is evaluated with these focusing signals. Besides, to calibrate the measured echo reduction via the TR technique, a standard sample is employed to measure a constant coefficient that only depends on the measurement environment. An aluminum plate sample and a steel plate sample with the same size of 1.1 mxl.O m x0.005 m axe tested in a wave guide tank. The experimental results show that the calibrated values are well consistent with theoretical results under the free field at the measured frequency range of0.5-20 kHz. The relative errors of all the measured values are less than 10% and the values of the expanded uncertainty are less than 1.5 dB. The TR processing focuses the energy in spatial domain and temporal domain, so it can be used to measure the echo reduction of passive materials in the environments with reflections induced by boundaries and low frequency sources.

Measurement of insertion loss for underwater acoustic passive materials with the time reversal technique

A method using the time reversal（TR） technique to measure the insertion loss（IL） of passive materials is presented.Firstly the received signals are focused according to the TR theory when there is not a sample between the source and the received array.Then,the sample is placed near the received array and the TR processing is again employed to realize the focus of the received signal.Finally,the IL of the sample is evaluated from these focusing signals.Because the TR processing can focus the energy in spatial domain and time domain,the method can be used to measure acoustic properties of passive materials in a waveguide tank with reflections induced by boundaries or with low source frequencies.Two samples with the same size of 1.1 m×1.0 m×5 mm are tested in the waveguide tank.The method is demonstrated by the comparison of the theoretical and the experimental results in the measured frequency range of 1-20 kHz.

Research on sound velocity measurement in a laboratory for large elastic materials

A measurement scheme carried out in a tank is designed to obtain the compressionaland shear-wave velocities of a large elastic material.A hydrophone is used to receive the high frequency acoustic signals which penetrate the tested material,in order to determine the transmission time from the source to the hydrophone,the transmission time is also calculated according to the ray acoustic theory in layered media.A cost function is built based on the measured and the calculated transmission time,then the compressional- and shear-wave velocities can be obtained using the optimization algorithm.Compared with the traditional measurement scheme,this approach can not only get the 2 kinds of sound velocities in the tested material at the same time,but also keep the integrality of the tested material.With the proposed measurement system,the uncertainty of measurement results is less than 3.5%.

Method based on broadband compressed pulse superposition to measure properties of underwater acoustic materials

A method is proposed for the measurements of the performances of underwater acoustic finite sized large area material samples in a free field by using broadband pulse compression technique. As the result of which, the low-frequency cutoff of the standard tests is obviously reduced, and the broadband measurements are also realized. The experimental system provides measurements of complex reflection and transmission coefficients at continuous frequency points. From the data one can obtain the following acoustic parameters: echo reduction and insertion loss, absorption and attenuation coefficients, etc. The measurements are performed for two actual panels with the size 1 m x 1 m in the frequency range from 2-20 kHz.

Investigation on method for measuring dynamic shear modulus of underwater acoustic structure materials

A new method is described to measure the dynamic shear modulus of underwater acoustic structure materials in a small anechoic water tank by using a broadband parametric source, a precise coordinate installation and techniques of signal processing in the frequency range of 20 kHz - 100 kHz. The typical size of material samples is 500×500 mm2. Basic principles, experiment installation and measured results are also presented

Mixing of particles and powders:Where next?

Industrial mixers for powders and granular materials operate with no effective control of mixture quality and lack scientific design. The last twenty years have seen growth in understanding of mixing and mixers. However, research falls far short of what is needed for on-line characterisation of mixture quality. Secondly, although theoretical descriptions of a few mixer types have been reported, these fall far short of what is needed for equipment design. Two thrusts could revolutionise this situation. One is a scientific characterisation of mixer structure applicable to industrial scale as well as laboratory scale equipment; this is now within our grasp using digital imaging. The other is the development of ideas to overcome the restricted number of particles that can be used in the Distinct Element Method （DEM） for mixers. The goal should be to take the designer through a sequence of steps to the most appropriate mixer size, configuration and operating conditions for a given process duty.