Materials flow and phase transformation in friction stir welding of Al 6013/Mg

Material flow and phase transformation were studied at the interface of dissimilar joint between Al 6013 and Mg, produced by stir friction welding （FSW） experiments. Defect-free weld was obtained when aluminum and magnesium were placed in the advancing side and retreating side respectively and the tool was placed 1 mm off the weld centerline into the aluminum side. In order to understand the material flow during FSW, steel shots were implanted as indexes into the welding path. After welding, using X-ray images, secondary positions of the steel shots were evaluated. It was revealed that steel shots implanted in advancing side were penetrated from the advancing side into the retreating side, whereas the shots implanted in the retreating side remained in the retreating side, without penetrating into the advancing side. The welded specimens were also heat treated. The effects of heat treatment on the mechanical properties of the welds and the formation of new intermetallic layers were investigated. Two intermetallic compounds, Al3Mg2 and Al12Mg17, were formed sequentially at Al6013/Mg interface.

A quantitative analysis of the US materials flow methodology and comparison to the EU methodology for MSW statistics

The European Union(EU)and the United States(US)determine municipal solid waste(MSW)statistics differently.The EU applies a site-specific methodology that directly measures waste whereas the US employs a materials flow methodology that estimates MSW statistics indirectly based on production and recovery data from industries.This study dissects the materials flow methodology and presents quantitative materials flow Sankey diagrams for the primary MSW materials to highlight data gaps that can be addressed to improve the methodology’s accuracy.Private industry plastics data were applied to the materials flow methodology,and the results were within 10%of the plastics statistics reported by the US Environmental Protection Agency(US EPA).Drawbacks to the methodologies include EU measurement inaccuracies due to double-counting and not accounting for residual waste in the US.The latter may partially explain why landfilling tonnages reported by the US EPA were approximately 60%less than the tonnages reported by the Waste to Energy Research and Technology Council(WTERT)in its national MSW survey that applied the EU methodology in the US.Unlike the EU,there is no US national policy that requires states to measure and report state-level waste data to the US EPA.Future improvements in US MSW statistics rely heavily on the implementation of national policies to homogenize the measurement and collection of waste data from states.

Enhancing wood efficiency through comprehensive wood flow analysis:Methodology and strategic insights

Wood,an essential natural resource in human civilization,remains widely used despite advances in technology and material substitution.The surge in greenhouse gas emissions and environmental concerns accentuates the need for optimizing wood utilization.Material flow analysis is a powerful tool for tracking material flows and stocks,aiding resource management and environmental decision-making.However,the full extent of its methodological dimensions,particularly within the context of the wood supply chain,remains relatively unexplored.In this study,we delve into the existing literature on wood flow analysis,discussing its primary objectives,materials involved,temporal and spatial scales,data sources,units,and conversion factors.Additionally,data uncertainty,data reconciliation and crucial assumptions in material flow analysis are highlighted in this paper.Key findings reveal the significance of wood cascading and substitution effects by replacing non-wood materials,where they can reduce greenhouse gas emissions more than the natural carbon sink of forests and wood products.The immediate impact of short-term wood cascading might not be as robust as the substitution effect,with energy substitution showcasing better results than material substitution.However,it's crucial to note that these conclusions could experience significant reversal from a long-term and global perspective.Strategies for improving wood efficiency involve maximizing material use,advancing construction technologies,extending product lifespans,promoting cascade use,and optimizing energy recovery processes.The study underscores the need for standardized approaches in wood flow analysis and emphasizes the potential of wood efficiency strategies in addressing environmental challenges.

A STUDY ON YIELD AND FLOW OF ORTHOTROPIC MATERIALS

On the assumption that the yield criterion of orthotropic materials is isomorphic with Huber-Mises criterion of isotropic materials, we put forward a dimensionless stress yield criterion, and obtained the associated plastic flow law. Using experimental stress-strain curves in various simple stress states, generalized effective stress-strain formulae may be derived correspondingly in various forms.

Visualization and simulation of plastic material flow in friction stir welding of 2024 aluminium alloy plates

Thin copper sheets as marker material were embedded into weld path of 2024 aluminium alloy plates and their final position after friction stir welding was examined by metallographic techniques. Referring to the visualized material flow patterns, a three-dimensional model was developed to conduct the numerical simulation of the temperature profile and plastic material flow in friction stir welding. The calculated velocity contour of plastic flow in close proximity of the tool is generally consistent with the visualized results. As the tool rotation speed increases at a constant tool travel speed, the material flow near the pin gets stronger. The predicted shape and size of the weld nugget zone match with the experimentally measured ones.

A Study on Alien Invasive Plants from the Interactive Mechanism between Species Niche and Material/Energy Flow

[Objective]This study was to reveal the essence of mechanism about how the alien invasive plants spread.[Method]Species niche and material/energy flow were used as basic research indicators to analyze the intrinsic mechanism of alien plants invasion.[Result]Most of the invasive plants have not been explicitly defined and their effective control methods not brought forward.[Conclusion]Overrun of alien invasive plants depends on whether the niche of a species could be continuously met at spatial level.Based on this we put forward corresponding control measures,proposed an assumption to establish a cylinder-network model and discussed the definition of alien invasive plants.

Effect of welding speed on the material flow patterns in friction stir welding of AZ31 magnesium alloy

The clear zigzag-line pattern on transverse cross sections can be used to explain the formation mechanism of the weld nugget when friction stir welded AZ31 magnesium alloy without any other insert material is used as mark. It provides a simple and useful method to research the joining mechanism of friction stir welding. The rotation speed is kept at 1000 r/min and the welding speed changes from 120 mm/min to 600 mm/min. The macrostructure on the transverse cross section was divided into several parts by faying surface. The results show that the shape and formation procedure of the weld nugget change with the welding speed. There are two main material flows in the weld nugget： one is from the advancing side and the other is from the retreating side. A simple model on the weld nugget formation of FSW is presented in this article.

Impact of material and energy flow variation-based iron /steel ratio on production cost

This paper establishes a model for the production cost of iron and steel enterprise.The variation rule of the production cost versus the iron/steel ratio for two cases, namely,fixed steel production and a fixed amount of molten iron,is analyzed,and the concept of a steel scrap threshold price is proposed.According to the analysis results,when the steel scrap unit price exceeds the steel scrap threshold price, an increase in the iron/steel ratio can reduce the production cost,and vice versa.When the gap between the steel scrap unit price and the steel scrap threshold price is relatively large, the impact of the iron/steel ratio on the production cost is more prominent.According to the calculation example,when steel production is fixed （284 358 t/month）and the steel scrap unit price is 263.2 yuan/t more than the steel scrap threshold price,an increase of 0.01 in the iron/steel ratio causes a monthly production cost reduction of approximately 750 000 yuan （2.63 yuan/t）.When the amount of molten iron is fixed （270 425 t/month）and the steel scrap unit price is 140.7 yuan/t more than the threshold price,an increase of 0.01 in the iron/steel ratio causes a monthly production cost reduction of approximately 430 000 yuan （1.5 yuan/t）.The results indicate that iron and steel enterprise should adjust the production strategy in time when the scrap price fluctuates, and then the production cost will be reduced.

Changes in functions,forms,and locations of lead during its anthropogenic flows to provide services

Knowledge of the changes in a material’s function, form, and location during the transfer and transformation of materials to generate human services will improve our understanding of how humanity interacts with the environment and of how services are formed by human activities. We compared lead’s anthropogenic and biogeochemical cycles and found that the services, pathways, and changes in form requiring the most attention. We traced lead through its life cycle and identified the changes in its functions, forms, and locations by examining technology and engineering information. Lead ore and scrap were the two main anthropogenic sources of lead. When lead provides human services, its main functions included the storage and delivery of electricity, anti-corrosion treatments, and radiation protection; the main forms of lead in these products were Pb, PbO2 and PbSO4, and the main location changed from lithosphere in central China to regions in eastern China.

Calculating Method for Influence of Material Flow on Energy Consumption in Steel Manufacturing Process

From the viewpoint of systems energy conservation, the influences of material flow on its energy consumption in a steel manufacturing process is an important subject. The quantitative analysis of the relationship between material flow and the energy intensity is useful to save energy in steel industry. Based on the concept of standard material flow diagram, all possible situations of ferric material flow in steel manufacturing process are analyzed. The expressions of the influence of material flow deviated from standard material flow diagram on energy consumption are put forward.

Material flow control technology of ironmaking and steelmaking interface

In order to achieve higher efficient cohesion match of procedure and equipment between ironmaking and steelmaking interface, the theory of multi-dimensional material flow control was applied to analyze torpedo ladle-iron ladle transportation process between blast furnace and basic oxygen furnace. Moreover, basic parameters of material flow were analyzed and optimized, such as time, temperature and material quantity. Based on operating principles of material flow, control methods were optimized, such as product organization mode, scheduling discipline and scheduling plan of hot metal ladle. Finally, the material flow control technology of ironmaking and steelmaking interface was integrated. Satisfactory effects are obtained after applying the technology in practice. The total turnover number of torpedo ladle decreases from 20 to 18, the hot metal temperature of 1# BF torpedo ladle decreases from 36 °C to 19.5 °C, the hot metal temperature of 2# BF torpedo ladle decreases from 36.6 °C to 19.8 °C, the temperature drop of desulfurization hot metal decreases by 4 °C, and the temperature drop of non-desulfurization hot metal decreases by 2.8 °C. Furthermore, the ironmaking and steelmaking interface system will realize high-efficiency control by using this control technology.

Influence of welding parameters on material flow,mechanical property and intermetallic characterization of friction stir welded AA6063 to HCP copper dissimilar butt joint without offset

Joining of dissimilar aluminium-copper is an emerging area of interest for both research and industry due to its complex nature.Friction stir welding was attempted to evaluate the joint strength without offset at the butt line between AA6063 to HCP copper sheet under different combination of rotational speed of 800 and 1000 r/min and travel speed of 20 and 40 mm/min.Material flow was studied in detail for different combinations of parameters with optical microscopy and elemental mapping by energy dispersive X-ray spectroscopy（EDS）.The results were correlated with the microstructural characteristics and formation of intermetallics at the bond interface using microhardness test and X-ray diffraction（XRD） technique.Material flow clearly suggests that energy input at 800 r/min and 20 mm/min is sufficient to plasticize both the materials with formation of higher amount of thermodynamically stable and hard intermetallic phases Al4Cu9 and Al Cu4（slower cooling rate of 88 K/s） than that at 800 r/min and 40 mm/min（faster cooling rate of 154 K/s）,attributed maximum joint strength（~78.6% of aluminium base metal）.

Effect of knurling shoulder design with polygonal pins on material flow and mechanical properties during friction stir welding of Al-Mg-Si alloy

Understanding the material flow facilitated by tool geometry in friction stir welds is challenging for quality weld production in industrial applications.The optimal tool shoulder and pin design combination,which plays a vital role in material flow was addressed.The flow of plasticized material was analyzed using a marker insert technique.The results show that the knurling shoulder design with square and hexagonal pin design facilitated constant stability force with reference to weld length/time.The uniform mixing and distribution of plasticized material were facilitated by the knurling shoulder design with square tool pin shape(TK)S(sticking length minimum)below which fragmented copper was observed.(TK)S tool facilitated higher mechanical properties for the welds,i.e.strength(182 MPa)and hardness(HV 78)in stir zone.

Effects of pin geometry on the material flow behavior of friction stir spot welded 2A12 aluminum alloy

A three-dimensional finite volume model was established by the ANSYS FLUENT software to simulate the material flow behavior during the friction stir spot welding （FSSW） process. Effects of the full-threaded pin and the reverse-threaded pin on the material flow behavior were mainly discussed. Results showed that the biggest material flow velocity appeared at the outer edge of the tool shoulder. The velocity value became smaller with the increase of the distance away from the tool surface. In general, material flows downwards along the pin thread when the full-threaded pin is used. Meanwhile, both the materials of the upper and the lower plates flow towards the lap interface along the pin thread when the reverse-threaded pin is used. The numerical simulation results were investigated by experiment, in which 2A12 aluminum alloy was used as the research object. The effective sheet thickness （EST） and stir zone （SZ） width of the joint by the reverse-threaded pin were much bigger than those by the full-threaded pin. Accordingly, cross tension failure load of the joint by the reverse-threaded pin is 23% bigger than the joint by the full-threaded pin.

3D visualization of the material flow in friction stir welding process

The material flow in friction stir welded 2014 Al alloy has been investigated using a marker insert technique （MIT）. Results of the flow visualization show that the material flow is asymmetrical during the friction stir welding （FSW） process and there are also significant differences in the flow patterns observed on advancing side and retreating side. On advancing side, some material transport forward and some move backward, but on retreating side, material only transport backward. At the top surface of the weld, significant material transport forward due to the action of the rotating tool shoulder. Combining the data from all the markers, a three-dituensional flow visualization, similar to the 3D image reconstruction technique, was obtained. The three-dimensional plot gives the tendency chart of material flow in friction stir welding process and from the plot it can be seen that there is a vertical, circular motion around the longitudinal axis of the weld. On the advancing side of the weld, the material is pushed downward but on the retreating side, the material is pushed toward the crown of the weld. The net result of the two relative motions in both side of the advancing and the retreating is that a circular motion comes into being. Comparatively, the material flow around the longitudinal axis is a secondary motion.

Numerical simulations on material flow behaviors in whole process of friction stir welding

A finite element model based on solid mechanics was developed with ABAQUS to study the material flow in wholeprocess of friction stir welding （FSW）, with the technique of tracer particles. Simulation results indicate that the flow pattern of thetracer particles around the pin is spiral movement. There are very different flow patterns at the upper and lower parts of the weld. Thematerial on the upper surface has the spiral downward movement that is affected by the shoulder and the lower material has the spiralupward movement that is affected by the pin. The velocity of the material flow on the periphery of the stirring pin is higher than thatat the bottom of the stirring pin. The material can be rotated with a stirring pin a few times, agreeing well with the previousexperimental observation by tungsten tracer particles.

Simulation of 3D material flow in friction stir welding of AA6061-T6

This paper reports the numerical simulation of the 3D material flow in friction stir welding process by using finite element methods based on solid mechanics. It is found that the material flow behind the pin is much faster than that in front of the pin. The material in front of the pin moves upwards and then rotates with the pin due to the effect of the rotating tool. Behind of the pin, the material moves downwards. This process of material movement is the real cause to make the friction stir welding process continuing successfully. With the increase of the translational velocity or the rotational velocity of the pin, the material flow becomes faster.

Influence of Material Flow in Steel Manufacturing Process on Atmosphere Environmental Load

The standard material flow diagram in steel manufacturing process was proposed to analyze the influences of various material flows on environmental load of 1tof final product.Two influence factors and reducing measures of environmental load were pointed out.The environmental load was appraised for a typical technological process in a Chinese steel plant.

INTEGRATED LAYOUT DESIGN OF CELLS AND FLOW PATHS

The integrated layout problem in manufacturing Systems is investigated. Anintegrated model for Concurrent layout design of cells and flow paths is formulated. A hybridapproach combined an enhanced branch-and-bound algorithm with a simulated annealing scheme isproposed to solve this problem. The integrated layout method is applied to re-layout the gear pumpshop of a medium-size manufacturer of hydraulic pieces. Results show that the proposed layout methodcan concurrently provide good solutions of the cell layouts and the flow path layouts.

Analysis of material flow and heat transfer in friction stir welding of aluminium alloys

A three-dimensional viscous-plastic.finite element model is established based on computational fluid mechanics. The material during the welding process is considered as non-Newtonian fluid abided by Norton-Hoff constitutive law, and viscous dissipation is assumed as the unique heat source. The model is used to numerically simulate the material flow and heat transfer in friction stir welding, and capture some useful process characteristics, .such as heat generation, temperature distribution and fluid.flow; besides, the velocity field is used to calculate streamlines of material flow, and the dimension of the deformation zone is measured.