Fractal Fractional Order Operators in Computational Techniques for Mathematical Models in Epidemiology

New fractional operators, the COVID-19 model has been studied in this paper. By using different numericaltechniques and the time fractional parameters, the mechanical characteristics of the fractional order model areidentified. The uniqueness and existence have been established. Themodel’sUlam-Hyers stability analysis has beenfound. In order to justify the theoretical results, numerical simulations are carried out for the presented methodin the range of fractional order to show the implications of fractional and fractal orders.We applied very effectivenumerical techniques to obtain the solutions of themodel and simulations. Also, we present conditions of existencefor a solution to the proposed epidemicmodel and to calculate the reproduction number in certain state conditionsof the analyzed dynamic system. COVID-19 fractional order model for the case of Wuhan, China, is offered foranalysis with simulations in order to determine the possible efficacy of Coronavirus disease transmission in theCommunity. For this reason, we employed the COVID-19 fractal fractional derivative model in the example ofWuhan, China, with the given beginning conditions. In conclusion, again the mathematical models with fractionaloperators can facilitate the improvement of decision-making for measures to be taken in the management of anepidemic situation.

Aquaporin-4-IgG-seropositive neuromyelitis optica spectrum disorders:progress of experimental models based on disease pathogenesis

Neuromyelitis optica spectrum disorders are neuroinflammatory demyelinating disorders that lead to permanent visual loss and motor dysfunction.To date,no effective treatment exists as the exact causative mechanism remains unknown.Therefore,experimental models of neuromyelitis optica spectrum disorders are essential for exploring its pathogenesis and in screening for therapeutic targets.Since most patients with neuromyelitis optica spectrum disorders are seropositive for IgG autoantibodies against aquaporin-4,which is highly expressed on the membrane of astrocyte endfeet,most current experimental models are based on aquaporin-4-IgG that initially targets astrocytes.These experimental models have successfully simulated many pathological features of neuromyelitis optica spectrum disorders,such as aquaporin-4 loss,astrocytopathy,granulocyte and macrophage infiltration,complement activation,demyelination,and neuronal loss;however,they do not fully capture the pathological process of human neuromyelitis optica spectrum disorders.In this review,we summarize the currently known pathogenic mechanisms and the development of associated experimental models in vitro,ex vivo,and in vivo for neuromyelitis optica spectrum disorders,suggest potential pathogenic mechanisms for further investigation,and provide guidance on experimental model choices.In addition,this review summarizes the latest information on pathologies and therapies for neuromyelitis optica spectrum disorders based on experimental models of aquaporin-4-IgG-seropositive neuromyelitis optica spectrum disorders,offering further therapeutic targets and a theoretical basis for clinical trials.

Exploiting fly models to investigate rare human neurological disorders

Rare neurological diseases,while individually are rare,collectively impact millions globally,leading to diverse and often severe neurological symptoms.Often attributed to genetic mutations that disrupt protein function or structure,understanding their genetic basis is crucial for accurate diagnosis and targeted therapies.To investigate the underlying pathogenesis of these conditions,researchers often use non-mammalian model organisms,such as Drosophila(fruit flies),which is valued for their genetic manipulability,cost-efficiency,and preservation of genes and biological functions across evolutionary time.Genetic tools available in Drosophila,including CRISPR-Cas9,offer a means to manipulate gene expression,allowing for a deep exploration of the genetic underpinnings of rare neurological diseases.Drosophila boasts a versatile genetic toolkit,rapid generation turnover,and ease of large-scale experimentation,making it an invaluable resource for identifying potential drug candidates.Researchers can expose flies carrying disease-associated mutations to various compounds,rapidly pinpointing promising therapeutic agents for further investigation in mammalian models and,ultimately,clinical trials.In this comprehensive review,we explore rare neurological diseases where fly research has significantly contributed to our understanding of their genetic basis,pathophysiology,and potential therapeutic implications.We discuss rare diseases associated with both neuron-expressed and glial-expressed genes.Specific cases include mutations in CDK19 resulting in epilepsy and developmental delay,mutations in TIAM1 leading to a neurodevelopmental disorder with seizures and language delay,and mutations in IRF2BPL causing seizures,a neurodevelopmental disorder with regression,loss of speech,and abnormal movements.And we explore mutations in EMC1 related to cerebellar atrophy,visual impairment,psychomotor retardation,and gain-of-function mutations in ACOX1 causing Mitchell syndrome.Loss-of-function mutations in ACOX1 result in ACOX1 deficiency,characterized by very-long-chain fatty acid accumulation and glial degeneration.Notably,this review highlights how modeling these diseases in Drosophila has provided valuable insights into their pathophysiology,offering a platform for the rapid identification of potential therapeutic interventions.Rare neurological diseases involve a wide range of expression systems,and sometimes common phenotypes can be found among different genes that cause abnormalities in neurons or glia.Furthermore,mutations within the same gene may result in varying functional outcomes,such as complete loss of function,partial loss of function,or gain-of-function mutations.The phenotypes observed in patients can differ significantly,underscoring the complexity of these conditions.In conclusion,Drosophila represents an indispensable and cost-effective tool for investigating rare neurological diseases.By facilitating the modeling of these conditions,Drosophila contributes to a deeper understanding of their genetic basis,pathophysiology,and potential therapies.This approach accelerates the discovery of promising drug candidates,ultimately benefiting patients affected by these complex and understudied diseases.

Mathematical Models of Tire-Longitudinal Road Adhesion and Their Use in the Study of Road Vehicle Dynamics

Mathematical models of tire-longitudinal road adhesion for use in the study of road vehicle dynamics are set up so as to express the relations of longitudinal adhesion coefficients with the slip ratio. They perfect the Pacejka's models in practical use by taking into account the influences of all essential parameters such as road surface condition. vehicle velocity. slip angle. vertical load and slip ratio on the longitudinal adhesion coefficients. The new models are more comprehensive more concise. simpler and more convenient in application in all kinds of simulations of car dynamics in various sorts of braking modes.

Mathematical Models of Tire-Lateral Road Adhesion for Use in Road Vehicle Dynamics Studies

Mathematical models of tire-lateral mad adhesion for use in mad vehicle dynamics studies are set up to express the relations of adhesion coefficients with slip ratio in lateral direction.The models of tire-lateral mad adhesion revolutionize the Pacejka's model in concept and therefore make it possible for applications in vehicle dynamics studies by the expression of lateral adhesion coefficient as a function of wheel slip ratio,instead of the wheel slip angle,taking into account in the mean time the influences of mad surface condition, vehicle velocity,vertical load,tire slip angle,and wheel camber angle.

Theoretical research and practical application of Mathematical economic models

Mathematical economic modeling is widely used to provide a reference for policy makers and guidance for the specific work of many departments, such as saving expenditures, reducing costs and improving profit. Particularly, it can predict and estimate the future, playing a great role in promoting the rapid development of science and technology as well as the management of market economy. In general, mathematics does not directly deal with the objective conditions on the management of market economy. In order to use mathematics to solve problems in the field of the management of market economic, it is necessary to carry out mathematical economic modeling.

Flow field simulation and establishment for mathematical models of flow area of spool valve with sloping U-shape notch machined by different methods

Precise function expression of the flow area for the sloping U-shape notch orifice versus the spool stroke was derived. The computational fluid dynamics was used to analyze the flow features of the sloping U-shape notch on the spool, such as mass flow rates, flow coefficients, effiux angles and steady state flow forces under different operating conditions. At last, the reliability of the mathematical model of the flow area for the sloping U-shape notch orifice on the spool was demonstrated by the comparison between the orifice area curve derived and the corresponding experimental data provided by the test. It is presented that the bottom arc of sloping U-shape notch （ABU） should not be omitted when it is required to accurately calculate the orifice area of ABU. Although the theoretical flow area of plain bottom sloping U-shape notch （PBU） is larger than that of ABU at the same opening, the simulated mass flow and experimental flow area of ABU are both larger than these of PBU at the same opening, while the simulated flow force of PBU is larger than that of ABU at the same opening. Therefore, it should be prior to adapt the ABU when designing the spool with proportional character.

Mathematical models and expert system for grate-kiln process of iron ore oxide pellet production.Part Ⅱ:Rotary kiln process control

Rotary kiln process for iron ore oxide pellet production is hard to detect and control.Construction of one-dimensional model of temperature field in rotary kiln was described.And the results lay a solid foundation for online control.Establishment of kiln process control expert system was presented,with maximum temperature of pellet and gas temperature at the feed end as control cores,and interval estimate as control strategy.Software was developed and put into application in a pellet plant.The results show that control guidance of this system is accurate and effective.After production application for nearly one year,the compressive strength and first grade rate of pellet are increased by 86 N and 2.54%,respectively,while FeO content is 0.05% lowered.This system can reveal detailed information of real time kiln process,and provide a powerful tool for online control of pellet production.

Mathematical models and expert system for grate-kiln process of iron ore oxide pellet production(Part Ⅰ):Mathematical models of grate process

Grate process is an important step in grate-kiln pellet production.However,as a relatively closed system,the process on grate is inaccessible to direct detection,therefore,it is hard to control.As a result,mathematical models of temperature distribution,moisture distribution and oxidation degree distribution in pellet bed,with good universality,computation speed and calculation accuracy,are presented based on analysis of heat transfer and physical-chemical reactions during grate process.And real-time visualization of temperature,moisture and oxidation degree distribution in pellet bed during grate process is realized.Model validation is displayed,and the similarity of 91% is proved.The results can reveal real time status on grate,and provide a solid foundation for the subsequent study of artificial intelligence control system of pellet production.

Mathematical models for foam-diverted acidizing and their applications

Foam diversion can effectively solve the problem of uneven distribution of acid in layers of different permeabilities during matrix acidizing. Based on gas trapping theory and the mass conservation equation, mathematical models were developed for foam-diverted acidizing, which can be achieved by a foam slug followed by acid injection or by continuous injection of foamed acid. The design method for foam-diverted acidizing was also given. The mathematical models were solved by a computer program. Computed results show that the total formation skin factor, wellhead pressure and bottomhole pressure increase with foam injection, but decrease with acid injection. Volume flow rate in a highpermeability layer decreases, while that in a low-permeability layer increases, thus diverting acid to the low-permeability layer from the high-permeability layer. Under the same formation conditions, for foamed acid treatment the operation was longer, and wellhead and bottomhole pressures are higher. Field application shows that foam slug can effectively block high permeability layers, and improve intake profile noticeably.

Mathematical models for properties of mortars with admixtures and recycled fine aggregates from demolished concretes

In order to expand the engineering application of recycle aggregate mortars （RAM） with aggregates from demolished concretes, the models for the properties of RAM and the replacement rate of these recycled fine aggregates were proposed. First, different kinds of mathematical models for the basic properties （compressive strength, water retention rate, and consistency loss） of RAM with two kinds of admixtures, thickening powders （TP） and self-made powdery admixtures （SSCT） designed for RAM, and the replacement rates were established, while the average relative errors and relative standard errors of these models were calculated. Additionally, the models and their error analyses for the curves of drying shrinkage and curing time of RAM ＋ SSCT at different replacement rates were put forward. The results show that polynomial functions should be used to calculate the basic properties of RAM ＋ TP and RAM ＋ SSCT at different replacement rates. In addition, polynonfial functions are the most optimal models for the sharp shrinkage sections in the curves of drying shrinkage-curing time of RAM ＋ SSCT, while exponential functions should be used as the models for the slow shrinkage sections and steady shrinkage sections.

Foundation of three—dimensional mathematical models for glass furnace regenerator

This paper presents a practical three dimensional mathematical model of circulation and heat transfer in generator of glass melting furnaces. The model was based on the heat transfer between the smoke flow and the lattice units, and between the air flow and the lattice units. This model not only bypassed the difficulty of complicated computation of the heat transfer process in the regenerator of glass furnaces, but also avoided the irrationality of fixing the temperature distribution on the surfaces. Use of the model yielded very important data and also the method for the design of the regenerator of glass furnaces in practical production.

Thermodynamic Consistency of Plate and Shell Mathematical Models in the Context of Classical and Non-Classical Continuum Mechanics and a Thermodynamically Consistent New Thermoelastic Formulation

Inclusion of dissipation and memory mechanisms, non-classical elasticity and thermal effects in the currently used plate/shell mathematical models require that we establish if these mathematical models can be derived using the conservation and balance laws of continuum mechanics in conjunction with the corresponding kinematic assumptions. This is referred to as thermodynamic consistency of the mathematical models. Thermodynamic consistency ensures thermodynamic equilibrium during the evolution of the deformation. When the mathematical models are thermodynamically consistent, the second law of thermodynamics facilitates consistent derivations of constitutive theories in the presence of dissipation and memory mechanisms. This is the main motivation for the work presented in this paper. In the currently used mathematical models for plates/shells based on the assumed kinematic relations, energy functional is constructed over the volume consisting of kinetic energy, strain energy and the potential energy of the loads. The Euler’s equations derived from the first variation of the energy functional for arbitrary length when set to zero yield the mathematical model(s) for the deforming plates/shells. Alternatively, principle of virtual work can also be used to derive the same mathematical model(s). For linear elastic reversible deformation physics with small deformation and small strain, these two approaches, based on energy functional and the principle of virtual work, yield the same mathematical models. These mathematical models hold for reversible mechanical deformation. In this paper, we examine whether the currently used plate/shell mathematical models with the corresponding kinematic assumptions can be derived using the conservation and balance laws of classical or non-classical continuum mechanics. The mathematical models based on Kirchhoff hypothesis (classical plate theory, CPT) and first order shear deformation theory (FSDT) that are representative of most mathematical models for plates/shells are investigated in this paper for their thermodynamic consistency. This is followed by the details of a general and higher order thermodynamically consistent plate/shell thermoelastic mathematical model that is free of a priori consideration of kinematic assumptions and remains valid for very thin as well as thick plates/shells with comprehensive nonlinear constitutive theories based on integrity. Model problem studies are presented for small deformation behavior of linear elastic plates in the absence of thermal effects and the results are compared with CPT and FSDT mathematical models.

Consistency and Validity of the Mathematical Models and the Solution Methods for BVPs and IVPs Based on Energy Methods and Principle of Virtual Work for Homogeneous Isotropic and Non-Homogeneous Non-Isotropic Solid Continua

Energy methods and the principle of virtual work are commonly used for obtaining solutions of boundary value problems (BVPs) and initial value problems (IVPs) associated with homogeneous, isotropic and non-homogeneous, non-isotropic matter without using (or in the absence of) the mathematical models of the BVPs and the IVPs. These methods are also used for deriving mathematical models for BVPs and IVPs associated with isotropic, homogeneous as well as non-homogeneous, non-isotropic continuous matter. In energy methods when applied to IVPs, one constructs energy functional (I) consisting of kinetic energy, strain energy and the potential energy of loads. The first variation of this energy functional (δI) set to zero is a necessary condition for an extremum of I. In this approach one could use δI = 0 directly in constructing computational processes such as the finite element method or could derive Euler’s equations (differential or partial differential equations) from δI = 0, which is also satisfied by a solution obtained from δI = 0. The Euler’s equations obtained from δI = 0 indeed are the mathematical model associated with the energy functional I. In case of BVPs we follow the same approach except in this case, the energy functional I consists of strain energy and the potential energy of loads. In using the principle of virtual work for BVPs and the IVPs, we can also accomplish the same as described above using energy methods. In this paper we investigate consistency and validity of the mathematical models for isotropic, homogeneous and non-isotropic, non-homogeneous continuous matter for BVPs that are derived using energy functional consisting of strain energy and the potential energy of loads. Similar investigation is also presented for IVPs using energy functional consisting of kinetic energy, strain energy and the potential energy of loads. The computational approaches for BVPs and the IVPs designed using energy functional and principle of virtual work, their consistency and validity are also investigated. Classical continuum mechanics (CCM) principles i.e. conservation and balance laws of CCM with consistent constitutive theories and the elements of calculus of variations are employed in the investigations presented in this paper.

Mathematical Models for Vacuum Drying Characteristics of Pomegranate Aril

The aim of this study was to investigate and determine the best mathematical models in describing vacuum drying characteristic of pomegranate arils in the range of 55-75 ℃. The vacuum batch dryer used in the evaluation was successful in drying a thin layer of pomegranate arils from the initial moisture content of 464.02% （d.b.） to 6.18% （d.b.） within 6.5 to 13.5 hr of continuous drying at the above mentioned temperature range. The drying rates increased with an increase in temperature and drying time. Five of the well known semi-theoretical and empirical models were fitted to the vacuum drying of pomegranate arils. The semi-empirical Midilli model has shown an excellent fit to predict drying behavior of the pomegranate arils because this model gave the highest coefficient of determination （RE）, the least chi-square （X2）, and the lowest root mean square error （RMSE）. The total drying occurs during falling period, signifying the influence of moisture diffusion during the drying. The effective diffusivity varied from 1.25× 10^10 to 2.91 × 10^10 m^2/s over the temperature range. Temperature dependence of the diffusivity was well documented by Arrhenius models. The activation energy of moisture diffusion during drying was found to be 40.46 kJ/mol.

Mathematical Models for a Social Partitioning Problem

In this paper we develop modeling techniques for a social partitioning problem. Different social interaction regulations are imposed during pandemics to prevent the spread of diseases. We suggest partitioning a set of company employees as an effective way to curb the spread, and use integer programming techniques to model it. The goal of the model is to maximize the number of direct interactions between employees who are essential for company’s work subject to the constraint that all employees should be partitioned into components of no more than a certain size implied by the regulations. Then we further develop the basic model to take into account different restrictions and provisions. We also give heuristics for solving the problem. Our computational results include sensitivity analysis on some of the models and analysis of the heuristic performance.

REVIEW ON MATHEMATICAL ANALYSIS OF SOME TWO-PHASE FLOW MODELS

The two-phase flow models are commonly used in industrial applications, such as nuclear, power, chemical-process, oil-and-gas, cryogenics, bio-medical, micro-technology and so on. This is a survey paper on the study of compressible nonconservative two-fluid model, drift-flux model and viscous liquid-gas two-phase flow model. We give the research developments of these three two-phase flow models, respectively. In the last part, we give some open problems about the above models.

ESTABLISHMENT AND APPLICATIONS OF MATHEMATICAL MODELS FOR CONCENTRATION DISTRIBUTION IN Mo－Fe－Ni－Co DIFFUSION QUARTERNARY──（Ⅱ） Characteristics and Applications of Mathematical Models

ＥＳＴＡＢＬＩＳＨＭＥＮＴＡＮＤＡＰＰＬＩＣＡＴＩＯＮＳＯＦＭＡＴＨＥＭＡＴＩＣＡＬＭＯＤＥＬＳＦＯＲＣＯＮＣＥＮＴＲＡＴＩＯＮＤＩＳＴＲＩＢＵＴＩＯＮＩＮＭｏ－Ｆｅ－Ｎｉ－ＣｏＤＩＦＦＵＳＩＯＮＱＵＡＲＴＥＲＮＡＲＹ──（Ⅱ）Ｃｈａｒａｃｔｅｒｉｓ...

Review of Non-Newtonian Mathematical Models for Rheological Characteristics of Viscoelastic Composites

This study presents an overview of viscoelastic characteristics of biocomposites derived of natural-fibre-reinforced thermoplastic polymers and predictive models have been presented in order to understand their rheological behavior. Various constitutive equations are reviewed for a better understanding of their applicability to polymer melt in determining the viscosity. The models to be investigated are the Giesekus-Leonov model, the Upper Convected Maxwell (UCM) model, the White-Metzner model, K-BKZ model, the Oldroyd-B model, and the Phan-Thien-Tanner models. The aforementioned models are the most powerful for predicting the rheological behavior of hybrid and green viscoelastic materials in the presence of high shear rate and in all dimensions. The Phan-Thien Tanner model, the Oldroyd-B model, and the Giesekus model can be used in various modes to fit the relaxation modulus accurately and to predict the shear thinning as well as shear thickening characteristics. The Phan-Thien Tanner, K-BKZ, Upper convected Maxwell, Oldroyd-B, and Giesekus models predicted the steady shear viscosity and the transient first normal stress coefficient better than the White-Metzner model for green-fibre-reinforced thermoplastic composites.

Adjustment of Mathematical Models and the Quality of Drying the Pulped Coffee at Different Air Conditions

The aim of the study was to describe the drying kinetics of washed coffee (Coffea arabica L.) and evaluate the best mathematical model to fit the experimental drying data conducted with different air humidity (40%, 50% and 60%), temperatures (23, 40 and 60 °C) and the quality of the coffee. The cherries coffee were separated and standardized in the processes of washing, mechanical and manual separation. Then, approx. 85 kg of coffee cherries were pulped and taken directly to the yard. The washed coffee was completed dried in a mechanical dryer and yard. The results showed that the different conditions of the ambient air significantly influenced the processes of drying. The water content of the hygroscopic equilibrium of pulped coffee is directly proportional to the water activity and relative humidity (RH), decreasing with increasing temperature, for the same value of equilibrium. The Oswin model was best represented by the hygroscopicity of the pulped coffee, while the Midilli model shows the best fit to describe the drying curves of the washed coffee. The effective diffusion coefficient increases with increasing temperature of the drying air and reducing of RH, being described by the Arrhenius equation. Electrical conductivity, potassium leaching, total titratable acidity and grease acidity increase with increasing drying temperature regardless of the type of processing. Reducing sugars, total sugars and the sensorial quality was negatively affected with increasing drying temperature regardless of the type of processing. The drying at 60 °C/40% RH negatively affected the coffee quality.