Microstructure evolution,mechanical properties and fracture behavior of Al-xSi/AZ91D bimetallic composites prepared by a compound casting

In this paper,the effect of the Si content on microstructure evolution,mechanical properties,and fracture behavior of the Al-xSi/AZ91D bimetallic composites prepared by compound casting was investigated systematically.The obtained results showed that all the Al-xSi/AZ91D bimetallic composites had a metallurgical reaction layer(MRL),whose thickness increased with increasing Si content for the hypoeutectic Al-Si/AZ91D composites,while the hypereutectic Al-Si/AZ91D composites were opposite.The MRL included eutectic layer(E layer),intermetallic compound layer(IMC layer)and transition region layer(T layer).In the IMC layer,the hypereutectic Al-Si/AZ91D composites contained some Si solid solution and flocculent Mg_(2)Si+Al-Mg IMCs phases not presented in the hypoeutectic Al-Si/AZ91D composites.Besides,increasing Si content,the thickness proportion of the T layer increased,forming an inconsistent preferred orientation of the MRL.The shear strengths of the Al-xSi/AZ91D bimetallic composites enhanced with increasing Si content,and the Al-15Si/AZ91D composite obtained a maximum shear strength of 58.6 MPa,which was 73.4% higher than the Al-6Si/AZ91D composite.The fractures of the Al-xSi/AZ91D bimetallic composites transformed from the T layer into the E layer with the increase of the Si content.The improvement of the shear strength of the Al-xSi/AZ91D bimetallic composites was attributed to the synergistic action of the Mg_(2)Si particle reinforcement,the reduction of oxidizing inclusions and the ratio of Al-Mg IMCs as well as the orientation change of the MRL.

Effect of heat treatment on the microstructure,mechanical properties and fracture behaviors of ultra-high-strength SiC/Al-Zn-Mg-Cu composites

A high-zinc composite,12vol%SiC/Al-13.3 Zn-3.27 Mg-1.07Cu(wt%),with an ultra-high-strength of 781 MPa was success-fully fabricated through a powder metallurgy method,followed by an extrusion process.The effects of solid-solution and aging heat treat-ments on the microstructure and mechanical properties of the composite were extensively investigated.Compared with a single-stage sol-id-solution treatment,a two-stage solid-solution treatment(470℃/1 h+480℃/1 h)exhibited a more effective solid-solution strengthen-ing owing to the higher degree of solid-solution and a more uniform microstructure.According to the aging hardness curves of the com-posite,the optimized aging parameter(100℃/22 h)was determined.Reducing the aging temperature and time resulted in finer and more uniform nanoscale precipitates but only yielded a marginal increase in tensile strength.The fractography analysis revealed that intergranu-lar cracking and interface debonding were the main fracture mechanisms in the ultra-high-strength SiC/Al-Zn-Mg-Cu composites.Weak regions,such as the SiC/Al interface containing numerous compounds and the precipitate-free zones at the high-angle grain boundaries,were identified as significant factors limiting the strength enhancement of the composite.Interfacial compounds,including MgO,MgZn2,and Cu5Zn8,reduced the interfacial bonding strength,leading to interfacial debonding.

Influences of shale microstructure on mechanical properties and bedding fractures distribution

The difference in microstructure leads to the diversity of shale mechanical properties and bedding fractures distribution patterns.In this paper,the microstructure and mechanical properties of Longmaxi marine shale and Qingshankou continental shale were studied by X-ray diffractometer(XRD),field emission scanning electron microscope(FE-SEM)with mineral analysis system,and nanoindentation.Additionally,the typical bedding layers area was properly stratified using Focused Ion Beam(FIB),and the effects of microstructure and mechanical properties on the distribution patterns of bedding fractures were analyzed.The results show that the Longmaxi marine shale sample contains more clay mineral grains,while the Qingshankou continental shale sample contains more hard brittle mineral grains such as feldspar.For Longmaxi marine shale sample,hard brittle minerals with grain sizes larger than 20μm is18.24%and those with grain sizes smaller than 20μm is 16.22%.For Qingshankou continental shale sample,hard brittle minerals with grain sizes larger than 20μm is 40.7%and those with grain sizes smaller than 20μm is 11.82%.In comparison to the Qingshankou continental shale sample,the Longmaxi marine shale sample has a lower modulus,hardness,and heterogeneity.Laminated shales are formed by alternating coarse-grained and fine-grained layers during deposition.The average single-layer thickness of Longmaxi marine shale sample is greater than Qingshankou continental shale sample.The two types of shale have similar bedding fractures distribution patterns and fractures tend to occur in the transition zone from coarse-grained to fine-grained deposition.The orientation of the fracture is usually parallel to the bedding plane and detour occurs in the presence of hard brittle grains.The fracture distribution density of the Longmaxi marine shale sample is lower than that of the Qingshankou continental shale sample due to the strong heterogeneity of the Qingshankou continental shale.The current research provides guidelines for the effective development of shale reservoirs in various sedimentary environments.

Microdynamic mechanical properties and fracture evolution mechanism of monzogabbro with a true triaxial multilevel disturbance method

The far-field microdynamic disturbance caused by the excavation of deep mineral resources and underground engineering can induce surrounding rock damage in high-stress conditions and even lead to disasters.However,the mechanical properties and damage/fracture evolution mechanisms of deep rock induced by microdynamic disturbance under three-dimensional stress states are unclear.Therefore,a true triaxial multilevel disturbance test method is proposed,which can completely simulate natural geostress,excavation stress redistribution(such as stress unloading,concentration and rotation),and subsequently the microdynamic disturbance triggering damaged rock failure.Based on a dynamic true triaxial test platform,true triaxial microdynamic disturbance tests under different frequency and amplitudes were carried out on monzogabbro.The results show that increasing amplitude or decreasing frequency diminishes the failure strength of monzogabbro.Deformation modulus gradually decreases during disturbance failure.As frequency and amplitude increase,the degradation rate of deformation modulus decreases slightly,disturbance dissipated energy increases significantly,and disturbance deformation anisotropy strengthens obviously.A damage model has been proposed to quantitatively characterize the disturbance-induced damage evolution at different frequency and amplitude under true triaxial stress.Before disturbance failure,the micro-tensile crack mechanism is dominant,and the micro-shear crack mechanism increases significantly at failure.With the increase of amplitude and frequency,the micro-shear crack mechanism increases.When approaching disturbance failure,the acoustic emission fractal dimension changes from a stable value to local large oscillation,and finally increases sharply to a high value at failure.Finally,the disturbance-induced failure mechanism of surrounding rock in deep engineering is clearly elucidated.

Effect of fractures on mechanical behavior of sand powder 3D printing rock analogue under triaxial compression

In practical engineering applications,rock mass are often found to be subjected to a triaxial stress state.Concurrently,defects like joints and fractures have a notable impact on the mechanical behavior of rock mass.Such defects are identified as crucial contributors to the failure and instability of the surrounding rock,subsequently impacting the engineering stability.The study aimed to investigate the impact of fracture geometry and confining pressure on the deformation,failure characteristics,and strength of specimens using sand powder 3D printing technology and conventional triaxial compression tests.The results indicate that the number of fractures present considerably influences the peak strength,axial peak strain and elastic modulus of the specimens.Confining pressure is an important factor affecting the failure pattern of the specimen,under which the specimen is more prone to shear failure,but the initiation,expansion and penetration processes of secondary cracks in different fracture specimens are different.This study confirmed the feasibility of using sand powder 3D printing specimens as soft rock analogs for triaxial compression research.The insights from this research are deemed essential for a deeper understanding of the mechanical behavior of fractured surrounding rocks when under triaxial stress state.

Mechanical properties and fracture behaviors on 6061 aluminum alloy under shear stress state

The mechanical properties and fracture behaviors of 6061 aluminum alloy were investigated by the tensile shear tests and in-situ tensile shear tests with tensile shear specimen devised. The results indicate that many slip bands parallel to tensile direction are produced on the surfaces of the specimens. With shear strain rates increasing, the shear yield stress and shear ultimate stress of 6061 aluminum alloy remain constant basically, but the shear fracture strain decreases obviously. The shear strain rates have no influence on the fracture surfaces. The grain boundaries of 6061 aluminum alloy are the weakest area and microcracks initiate at the grain boundaries parallel to tensile direction under shear stress. With the shear stress increasing, the microcracks extend and coalesce. The fracture of specimens is due to coalescence or shearing between the microcracks.

Age hardening,fracture behavior and mechanical properties of QE22 Mg alloy

The microstructure,mechanical properties and fracture behavior of an as-received QE22 alloy have been investigated under different thermal conditions,including solution treated(ST),under aged(UA),peak aged(PA)and over aged(OA)conditions.A significant increase in hardness of 27%,yield strength of 60%and ultimate tensile strength of 19%was observed in peak aged sample as compared to solution treated sample.The improvements of mechanical strength properties are mainly associated with the metastable λ and β′precipitates.Grain growth was not observed in the ST samples after subjecting to UA and PA treatments due to the presence of eutectic Mg_(12)Nd particles along the grain boundaries.In over aged sample,significant grain growth occurred because of dissolution of eutectic phase particles.Different natures of crack initiation and propagation were observed under different thermal conditions during tensile testing at room temperature.The mode of failure of solution treated sample is transgranular,cleavage and twin boundary fractures.A mixed mode of transgranular,intergranular,cleavage and twin boundary failure is observed in both peak aged and over aged samples.

Effect of Zn content on microstructure, mechanical properties and fracture behavior of Mg-Mn alloy

The optical microscope, scanning electron microscope and universal testing machine are used to investigate the effect of Zn content on the microstructure, mechanical properties and fracture behavior of Mg- Mn-Zn alloy. The results indicate that fine （Mg, Mn, AI）-containing phases are distributed uniformly in the Mg-Mn alloy matrix, while small amount of （Mg, Zn）-containing phases are formed in the matrix and the grain boundary becomes coarse when 1wt.% Zn is added. As the Zn content increases, the amount of （Mg, Zn）-containing phases increases, and the grain boundary becomes coarser. When the Zn content is between 3wt.%-5wt.%, slender （Mg, Zn）-containing phases precipitate at the grain boundary. The addition of Zn could reduce the grain size and enhance the mechanical properties of the alloy matrix, and both of the effects can be enhanced by increasing the Zn content further more. When the Zn content is more than 3wt.%, grain size stops decrease, the strength cannot be improved any more and elongation decreases significantly. The fracture behavior of Mg-Mn alloy appears to be cleavage fracture, and transforms into quasi-cleavage fracture as Zn is added. When Zn content exceeded 3wt.%, large amount of （Mg, Zn）-containing phases appear on the fracture face, and act as the crack sources.

Effect of reclaimed sand additions on mechanical properties and fracture behavior of furan no-bake resin sand

In this work, the effects of reclaimed sand additions on the microstructure characteristics, mechanical properties and fracture behavior of furan no-bake resin sand have been investigated systematically within the temperature range from 25 to 600 oC. The addition of 20%-100% reclaimed sand showed dramatic strength deterioration effect at the same temperature, which is associated with the formation of bonding bridges. Both the ultimate tensile strength(UTS) and compressive strength(CS) of the moulding sand initially increase with the increase of temperature, and then sharply decrease with the further increase of temperature, which is attributed to the thermal decomposition of furan resin. The addition amount of reclaimed sand has a remarkable effect on the room temperature fracture mode, i.e., with the addition of 0-20% reclaimed sand, the fracture mode was mainly cohesive fracture; the fracture mode converts to be mixture fracture mode as the addition of reclaimed sand increases to 35%-70%; further increasing the addition to 100% results in the fracture mode of typical adhesive fracture. The fracture surface of the bonding bridge changes from a semblance of cotton or holes to smooth with the increase of test temperature.

Aging behavior and mechanical properties of 6013 aluminum alloy processed by severe plastic deformation

Structural features, aging behavior, precipitation kinetics and mechanical properties of a 6013 Al–Mg–Si aluminum alloy subjected to equal channel angular pressing （ECAP） at different temperatures were comparatively investigated with that in conventional static aging by quantitative X-ray diffraction （XRD） measurements, differential scanning calorimetry （DSC） and tensile tests. Average grain sizes measured by XRD are in the range of 66-112 nm while the average dislocation density is in the range of 1.20×10^14-1.70×10^14 m^-2 in the deformed alloy. The DSC analysis reveals that the precipitation kinetics in the deformed alloy is much faster as compared with the peak-aged sample due to the smaller grains and higher dislocation density developed after ECAP. Both the yield strength （YS） and ultimate tensile strength （UTS） are dramatically increased in all the ECAP samples as compared with the undeformed counterparts. The maximum strength appears in the samples ECAP treated at room temperature and the maximum YS is about 1.6 times that of the statically peak-aged sample. The very high strength in the ECAP alloy is suggested to be related to the grain size strengthening and dislocation strengthening, as well as the precipitation strengthening contributing from the dynamic precipitation during ECAP.

Effect of heat treatment on microstructure, mechanical properties and in vitro degradation behavior of as-extruded Mg-2.7Nd-0.2Zn-0.4Zr alloy

Mg-2.7Nd-0.2Zn-0.4Zr （mass fraction, %） alloy was designed for degradable biomedical material. The ingots of the alloy were solution treated and then hot extruded. The extruded rods were heat treated with aging treatment, solution treatment and solution＋aging treatment, respectively. Microstructures of the alloy were observed by optical microscopy （OM） and scanning electron microscopy （SEM）. Mechanical properties at room temperature were tested. In vitro degradation behavior of the alloy immersed in simulated body fluid was measured by hydrogen evolution and mass loss tests. The degradation morphologies of the alloy with and without degradation products were observed by SEM. The results show that the grains grow apparently after solution treatment. Solution treatment improves the elongation of as-extruded alloy significantly and decreases the strength, while aging treatment improves the strength and reduces the elongation of the alloy. The yield ratio is reduced by heat treatment. The in vitro degradation results of the alloy show that solution treatment on the as-extruded alloy results in a little higher degradation rate and aging treatment on the alloy can reduce degradation rate slightly.

Mechanical properties and fracture toughness of rail steels and thermite welds at low temperature

Brittle fracture occurs frequently in rails and thermite welded joints, which intimidates the security and reliability of railway ser- vice. Railways in cold regions, such as Qinghai-Tibet Railway, make the problem of brittle fi＇acture in rails even worse. A series of tests such as uniaxial tensile tests, Charpy impact tests, and three-point bending tests were carried out at low temperature to investigate the mechanical properties and fracture toughness of U71Mn and U75V rail steels and their thermite welds. Fracture micromechanisms were analyzed by scanning electron microscopy （SEM） on the fracture surfaces of the tested specimens. The ductility indices （percentage elongation aider frac- ture and percentage reduction of area） and the toughness indices （Charpy impact energy Ak and plane-strain fracture toughness Kic） of the two kinds of rail steels and the corresponding thermite welds all decrease as the temperature decreases. The thermite welds are more critical to fracture than the rail steel base metals, as indicated by a higher yield-to-ultimate ratio and a much lower Charpy impact energy. U71Mn rail steel is relatively higher in toughness than U75V, as demonstrated by larger Ak and Klc values. Therefore, U71Mn rail steel and the corresponding thermite weld are recommended in railway construction and maintenance in cold regions.

Microstructure,mechanical properties and corrosion behavior of Al-Si-Cu-Zn-X(X=Bi,Sb,Sr) die cast alloy

The microstructure evolution, mechanical and corrosion properties of Al-11Si-2Cu-0.8Zn die cast alloy treated with Bi, Sb and Sr additions were investigated. The results of mechanical testing showed that all additions increased impact toughness, ultimate tensile strength, and elongation of the alloy as a result of change in eutectic Si morphology. The analysis of fracture surfaces revealed that with addition of Sr and to lesser extent Bi and Sb, the alloy exhibited a predominantly ductile fracture rather than quasi-cleavage brittle fracture. Moreover, with the additions of Sr, Bi and Sb, the quality index increased to 164.7 MPa, 156.3 MPa and 152.6 MPa respectively from 102 MPa for the base alloy. Polarization corrosion tests conducted in sodium chloride solution showed that the corrosion potential shifted to more negative values with additions of Sb, Bi and Sr, respectively. Corrosion immersion tests also revealed that the element additions have a detrimental effect on the corrosion rate of alloys, due to the increase of boundaries between the Al and eutectic Si phases.

Tensile properties and fracture behavior of Ti_2AlNb based alloys at room temperature

The tensile mechanical properties and fracture behaviors of Ti 22Al 20Nb 7Ta alloys were studied at room temperature. Three typical microstructures of Ti 2AlNb based alloys were obtained by combination of thermal mechanical processing and heat treat ment. They are: 1) lath mixture of O + B 2 with remaining β grain boundaries and α 2 phase; 2) equiaxed O phase in B 2 matrix; 3) fine lath mixture of O + B 2 without remaining β grain boundaries. It is shown that the microstructure obviously affects the tensile properties of Ti 2AlNb based alloys. The microstructure of fine lath mixture of O + B 2 without remaining β grain boundaries has good combination of yield stress and ductility, while the microstructure with lath mixture of O + B 2 with remaining β grain boundaries and α 2 phase has low yield stress and elongation. The fracture mode was also controlled by the microstructure of Ti 2AlNb based alloys. By means of SEM, it was found that the dominated fracture mode of microstructure with lath mixture of O + B 2 with remained β grain boundary and α 2 phase was intergranular, and the fracture mode of the other two microstructures was mainly transgranular.

Influence of Ca addition on microstructure,mechanical properties and corrosion behavior of Mg-2Zn alloy

The microstructure,mechanical properties and corrosion behaviors of as-cast ternary Mg-2Zn-x Ca(x=0,0.2,0.4,0.8)alloys have been investigated in this study.Results indicate that the microstructure of Mg-Zn-Ca alloys can be significantly refined with increasing Ca concentration.Moreover,the alloys with different contents of Ca exhibit the different phases formation behaviors,i.e.α-Mg+Ca_2Mg_6Zn_3 phases for Mg-2Zn-0.2Ca and Mg-2Zn-0.4Ca alloys,andα-Mg+Ca_2Mg_6Zn_3+Mg_2Ca phases for Mg-2Zn-0.8Ca alloy,respectively.Among all the alloys,the maximum ultimate tensile strength and elongation(161 MPa and 9.1%)can be attained for the Mg-2Zn-0.2Ca alloy.Corrosion tests in Hanks’balanced salt solution indicated that Ca addition is detrimental to corrosion resistance of Mg-2Zn alloy.The relationship between as-cast microstructure and properties for different Ca-containing alloys is also discussed in detail.

Mechanical properties and fracture mechanism of as-cast MnFeCoCuNix high-entropy alloys

MnFeCoCuNix high-entropy alloys(HEAs)with different Ni contents were fabricated by vacuum induction melting.XRD and SEM−EDS were used to analyze the phase constitution and structure,and the tensile properties of the samples were determined using a universal tensile tester.The results show that the HEAs consist of a dual-phase structure,in which FCC1 phase is rich in Fe and Co,while the FCC2 phase has high contents of Cu and Mn.As Ni content increases,the segregation of Cu decreases,accompanied by the decrease of FCC2 phase.Moreover,the tensile strength of the HEAs increases first and then decreases,and the elongation increases slightly.This is attributed to the combined effect of interface strengthening and solid solution strengthening.The in-situ stretched MnFeCoCuNi0.5 alloy shows obvious neck shrinkage during the tensile fracture process.In the initial deformation stage,the slip lines show different morphologies in the dual-phase structure.However,in the later stage,the surface slip lines become longer and denser due to the redistribution of atoms and the re-separation of the dissolved phase.

Effect of Zr modification on solidification behavior and mechanical properties of Mg–Y–RE (WE54) alloy

Magnesium alloys containing rare earth elements (RE) have received considerable attention in recent years due to their high mechanical strength and good heat-resisting performance. Among them, Mg–5%Y–4%RE (WE54) magnesium alloy is a high strength sand casting magnesium alloy for use at temperatures up to 300 ℃, which is of great interest to engineers in the aerospace industry. In the present work, the solidification behavior of Zr-containing WE54 alloy and Zr-free alloy was investigated by computer-aided cooling curve analysis (CA-CCA) technique. And the solidification microstructure and mechanical properties of them were also investigated comparatively. It is found from the cooling curves and as-cast microstructure of WE54 alloy that the nucleation temperature of α-Mg in WE54 alloy increases after Zr addition, and the as-cast microstructure of the alloy is significantly refined by Zr. While the phase constitution of WE54 alloy is not changed after Zr addition. These phenomena indicate that Zr acts as heterogeneous nuclei during the solidification of WE54 alloy. Due to refined microstructure, the mechanical properties of Zr-containing WE54 alloy is much higher than Zr-free WE54 alloy.

Microstructure,mechanical properties and corrosion behavior of quaternary Mg−1Zn−0.2Ca−xAg alloy wires applied as degradable anastomotic nails

The microstructure,mechanical properties and corrosion behavior of quaternary degradable Mg−1Zn−0.2Ca−xAg(x=1,2,4 wt.%)alloy wires,intended as anastomotic nails,were investigated.It was found that these Ag-containing alloy wires mainly consist of Mg matrix and Ag17Mg54 phase,characterized by SEM,EDS,XRD and TEM.Tensile and knotting tests results demonstrate the superior mechanical properties of these alloy wires.Especially,Mg−1Zn−0.2Ca−4Ag alloy exhibits the highest mechanical properties,i.e.an ultimate tensile strength of 334 MPa and an elongation of 8.6%.Moreover,with increasing Ag content,the corrosion rates of these alloy wires remarkably increase due to the formation of more micro-galvanic coupling between Mg matrix and Ag17Mg54 phase,shown by mass loss and scanning Kelvin probe force microscopy(SKPFM)results.The present alloy can be completely degraded within 28 d,satisfying the property requirements of anastomotic nails.

Enhancing the mechanical properties of casting eutectic high -entropy alloys via W addition

The effect of W element on the microstructure evolution and mechanical properties of Al_(1.25)CoCrFeNi3 eutectic high-entropy alloy and Al_(1.25)CoCrFeNi_(3-x)W_(x)(x=0,0.05,0.1,0.3,and 0.5;atomic ratio)high-entropy alloys(HEAs)were explored.Results show that the Al_(1.25)CoCrFeNi_(3-x)W_(x) HEAs are composed of face-centered cubic and body-centered cubic(BCC)phases.As W content increases,the microstructure changes from eutectic to dendritic.The addition of W lowers the nucleation barrier of the BCC phase,decreases the valence electron concentration of the HEAs,and replaces Al in the BCC phase,thus facilitating the nucleation of the BCC phase.Tensile results show that the addition of W greatly improves the mechanical properties,and solid-solution,heterogeneous-interface,and second-phase strengthening are the main strengthening mechanisms.The yield strength,tensile strength,and elongation of the Al_(1.25)CoCrFeNi2.95W0.05 HEA are 601.44 MPa,1132.26 MPa,and 15.94%,respectively,realizing a balance between strength and plasti-city.The fracture mode of the Al_(1.25)CoCrFeNi_(3-x)W_(x) HEAs is ductile–brittle mixed fracture,and the crack propagates and initiates in the BCC phase.The eutectic lamellar structure impedes crack propagation and maintains plasticity.

Creep behavior and mechanical properties of Al-Li-S4 alloy at different aging temperatures

Creep age forming techniques have been widely used in aerospace industries. In this study, we investigated the effect of aging temperature(143 °C-163 °C) on the creep behavior of Al-Li-S4 aluminum alloy and their mechanical properties at room temperature. The mechanical properties were tested by tensile testing, and the microstructural evolution at different aging temperatures was examined by transmission electron microscopy. Results show that the creep strains and the room-temperature mechanical properties after creep aging increase with the aging temperature. As the aging temperature increases, the creep strain increases from 0.018% at 143 °C to 0.058% at 153 °C, and then to 0.094% at 163 °C. Within 25 h aging, the number of creep steps increases and the duration time of the same steps is shortened with the growth of aging temperatures. Therefore, the increase in aging temperatures accelerates the progress of the entire creep. Two main strengthening precipitates θ′(Al2 Cu) and T1(Al2 Cu Li) phases were characterized. This work indicates that the creep strain and mechanical properties of Al-Li-S4 alloys can be improved by controlling aging temperatures.