Loss Factors and their Effect on Resonance Peaks in Mechanical Systems

The loss factors and their effects on the magnitude and frequency of resonance peaks in various mechanical sys-tems are reviewed for acoustic,vibration,and vibration fatigue applications.The main trends and relationships were obtained for linear mechanical models with hysteresis damping.The well-known features(complex module of elasticity,total loss factor,etc.)are clarified for practical engineers and students,and new results are presented(in particular,for 2-DOF in-series models with hysteresis friction).The results are of both educational and prac-tical interest and may be applied for NVH analysis and testing,mechanical and aeromechanical design,and noise and vibration control in buildings.

Losses of Soil Organic Carbon and Nitrogen and Their Mechanisms in the Desertification Process of Sandy Farmlands inHorqin Sandy Land

Soil organic carbon(SOC)and total nitrogen(N)concentrations from bulk soils and soil particle size fractions in the different extent of desertified farmlands(potential, light, medium, severe, and most severe desertified farmlands)were examined to quantitatively elucidate losses of carbon and nitrogen and its mechanisms in the desertification process. Particle size fractions(2 -0.1 mm, 0.1 - 0.05 mm, <0.05 mm)were obtained by granulometric wet sieving from 30 sandy soils(0 - 15cm depth)of different desertified extent. It was shown that soil physical stability index(St)in most severe desertified farmlands was 5 -7% and St in other farmlands was less than 5 %, which contributed to very low soil organic matter content. This was the intrinsic cause that sandy farmlands in Horqin sandy land was subject to risk of desertification. Desertification resulted in considerable losses of SOC and N. Regression analysis indicated that SOC and N content reduced 0.169 g kg-1 and 0.0215 g kg-1 respectively with one percent loss of soil silt and clay content. Losses of SOC and N were mostly the removal of fine particle size fractions(silt and clay, and a less extent very fine sand)from the farmlands by wind erosion, which were rich in organic matter and nutrients, as well as the depletion of organic C and N associated with coarse particles(>0. 05 mm)in desertification process. The concentrations of C and N associated with sand(2 - 0.1 mm and 0.1 - 0.05 mm)significantly decreased with increase of desertified extent. Silt and clay associated C and N concentrations, however, were less changed, and in contrast, were higher in soils under most severe desertified extent than in soils under potential and severe desertified extent. The percentage of distribution in sand(>0.05 mm)associated C and N significantly increased with increase of desertified extent, suggesting that stability of SOC decreased in the desertification process.

Contact force and mechanical loss of multistage cable under tension and bending

A theoretical model for calculating the stress and strain states of cabling structures with different loadings has been developed in this paper. We solve the problem for the first- and second-stage cable with tensile or bending strain. The contact and friction forces between the strands are presented by two-dimensional contact model. Several theoretical models have been proposed to verify the results when the triplet subjected to the tensile strain, including contact force, contact stresses, and mechanical loss. It is found that loadings will affect the friction force and the mechanical loss of the triplet. The results show that the contact force and mechanical loss are dependent on the twist pitch. A shorter twist pitch can lead to higher contact force, while the trend of mechanical loss with twist pitch is complicated. The mechanical loss may be reduced by adjusting the twist pitch reasonably. The present model provides a simple analysis method to investigate the mechanical behaviors in multistage-structures under different loads.

Evaluation of corrosion resistance, mechanical integrity loss and biocompatibility of PCL/HA/TiO_(2) hybrid coated biodegradable ZM21 Mg alloy

A novel PCL/HA/TiO_(2)hybrid coating on ZM21 Mg alloy substrate has been investigated for corrosion resistance, biocompatibility and mechanical integrity loss in terms of bending, compressive and tensile strength in physiological media. The prepared hybrid coating was dip coated over ZM21 from HA/TiO_(2)and PCL solutions followed by creating a microporous PCL layer by utilizing Non-solvent Induced Phase Separation(NIPS) technique. The electrochemical measurement and in-vitro degradation study in SBF after 28 days showed that the PCL/HA/TiO_(2) hybrid coating reduced H2 evolution rate, weight loss, and corrosion rate by 64, 116 and 118 times respectively, as compared to uncoated ZM21 samples. The surface studies carried out using SEM-EDX, FTIR and XRD revealed formation of highly stable 3d flower-like HA crystals with Ca/P ratio of 1.60 in the PCL micropores. This dense apatite growth effectively protected the PCL/HA/TiO_(2)hybrid coated samples to maintain the good mechanical integrity even after 28 days of immersion as compared to HA/TiO_(2)composite coated, As-polished(A/P) and As-machined(A/M) samples. The failure analysis of samples under mechanical loading were performed using SEM-BSE-EBSD.The in-vitro cellular viability of L929 fibroblast cells on PCL/HA/TiO_(2)hybrid coating was found 50.47% higher with respect to control group,whereas bacterial viability was supressed by 57.15 and 62.35% against gram-positive Staphylococcus aureus and gram-negative Escherichia coli bacterial models. The comprehensive assessment indicates PCL/HA/TiO_(2)hybrid coating as a suitable candidate to delay early degradation and mechanical integrity loss of Mg-based alloys for devising biodegradable orthopaedic implant.

Fabrication of a flexible microwave absorber sheet based on a composite filler with fly ash as the core filled silicone rubber

A new type of composite filler was designed by a modified sol-gel method using fly ash(FA),Fe(NO_(3))_(3)·9H_(2)O,and Ni(NO_(3))_(2)·6H_(2)O as raw materials.The composite filler was a spherical core-shell structure composed of FA as the core and NiFe_(2)O_(4)as the shell.Further,the composite filler was added into the silicone rubber to fabricate the high temperature vulcanized microwave absorption materials;X-ray diffraction,fourier transform infrared spectroscopy,X-ray photoelectron spectroscopy,and scanning electron microscope confirmed that NiFe_(2)O_(4)was successfully coated on the surface of FA and formed a uniform and continuous coating layer.As expected,silicone rubber filled with the composite filler had a minimum reflection loss of-23.8 dB at 17.5 GHz with the thickness of 1.8 mm,while the effective absorption bandwidth was as high as 12 GHz.The addition of the composite filler greatly enhanced the microwave absorption properties of the system,which was resulted from multiple losses mechanism:interface polarization losses,magnetic losses,and multiple reflection losses.Also,silicone rubber filled with the composite filler exhibited excellent thermal stability,flexibility,environmental resistance,and hydrophobicity compared with traditional silicone rubber.Therefore,this work not only responds to the green chemistry to achieve efficient FA recovery,but also devises a new strategy to prepare microwave absorption materials with strong potential for civilian applications.

Mechanism of Strength Loss of No-bake Phosphate Bonded Sand Mold/Core

The strength loss mechanism of the phosphate bonded sand mold/core was studied. The morphology and composition of phosphate membrane on the surface of sands was analyzed with electron probe X-ray microanalyzer. Results show that magnesium causes cracks in cured phosphate membrane and results in the decrease of sand molds/cores strength. However, the addition of magne-sium significantly enhanced hygroscopy resistance of phosphate membrane. In addition, the phosphate binder added with the magnesium modifier has more rapid hardening reaction speed compared that without or with low magnesium binder. It can be concluded that the phosphate binder with the addition of magnesium modifier is favorably used in high humid and cold circumstance.

Temperature field analysis of two rotating and squeezing steel-rubber rollers

Rubber has strong nonlinear viscoelastic characteristic. Under effect of the periodically changing external force,it will show the phenomenon of lagging deformation and mechanical loss,which means deformation lags behind stress changes and the situation of loss of work is caused by the hysteresis. Loss of work will be transformed into thermal energy and makes the temperature of rubber and the object in contact with it rise,which will thereby affect the dynamic characteristics of the structure. Based on a pair of mutual rotating and squeezing steel-rubber rollers as the research object,the finite element simulation software Ansys is used in this paper to analyze the temperature field of the structure. As a result,temperature distribution characteristics of two directions are obtained. One is squeezing area along the direction of the wall,the other is along the direction of thickness of rubber. Then the influence of the rotating speed and the pressure between two rollers on temperature of rubber is analyzed. The temperature experiment of mutual squeezing contact steelrubber roller is carried out on the experimental platform via using infrared thermal imager and infrared thermometer. The experiment data are in accordance with the simulation results on regulation of temperature distribution as well as high degree of similarity on value,which shows the effectiveness of simulation. Research results are of great significance for temperature characteristic analysis of rubber structure.

Biochemical Genetic Mechanism and QTLs of Early Maturing without Yield Loss in Short-season Upland Cotton(Gossypium hirsutum L.)

The short season cotton(SSC) was important Upland plant ecotype(Gossypium hirsutum L.).The growth of SSC was very short that is 105 ～ 110 days(after planting). SSC could increase

Investigation of the Antioxidant and UV Absorption Properties of 2-(2’-hydroxy-5’-methylphenyl)-benzotriazole and Its Ortho-Substituted Derivatives via DFT/TD-DFT

The demand and pursuit of chemical entities with UV filtration and antioxidant properties for enhanced photoprotection have been driven in recent times by acute exposure of humans to solar ultraviolet radiations. The structural, electronic, antioxidant and UV absorption properties of drometrizole (PBT) and designed ortho-substituted derivatives are reported via DFT and TD-DFT in the gas and aqueous phases. DFT and TD-DFT computations were performed at the M062x-D3Zero/6-311++G(d,p)//B97-3c and PBE0-D3(BJ)/def2-TZVP levels of theory respectively. Reaction enthalpies related to hydrogen atom transfer (HAT), single-electron transfer followed by proton transfer (SET-PT), and sequential proton loss electron transfer (SPLET) mechanisms were computed and compared with those of phenol. Results show that the presence of -NH2 substituent reduces the O-H bond dissociation enthalpy and ionization potential, while that of -CN increases the proton affinity. The HAT and SPLET mechanisms are the most plausible in the gas and aqueous phases respectively. The molecule with the -NH2 substituent (PBT1) was identified to be the compound with the highest antioxidant activity. The UV spectra of the studied compounds are characterized by two bands in the 280 - 400 nm regions. Results from this study provide a better comprehension antioxidant mechanism of drometrizole and present a new perspective for the design of electron-donor antioxidant molecules with enhanced antioxidant-photoprotective efficiencies for applications in commercial sunscreens.

Flow Loss Mechanism in a Supercritical Carbon Dioxide Centrifugal Compressor at Low Flow Rate Conditions

With the advantages of high efficiency and compact structure,supercritical carbon dioxide(sC02)Brayton cycles have bright prospects for development in energy conversion field.As one of the core components of the power cycle,the centrifugal compressor tends to operate near the critical point(304.13 K,7.3773 MPa).Normally,the compressor efficiency increases as the inlet temperature decreases.When the inlet temperature is close to the critical point,the density increases sharply as the temperature decreases,which results in quickly decreasing of volume flow rate and efficiency reducing.The flow loss mechanism of the sCO_(2) compressor operating at low flow rate is studied in this paper.Computational fluid dynamics(CFD) simulations for sCO_(2)compressor were carried out at various inlet temperatures and various mass flow rates.When the sCO_(2)compressor operates at low volume flow rate,the flow loss is generated mainly on the suction side near the trailing edge of the blade.The flow loss is related to the counterclockwise vortexes generated on the suction side of the main blade.The vortexes are caused by the flow separation in the downstream region of the impeller passage,which is different from air compressors operating at low flow rates.The reason for this flow separation is that the effect of Coriolis force is especially severe for the sCO_(2) fluid,compared to the viscous force and inertial force.At lower flow rates,with the stronger effect of Coriolis force,the direction of relative flow velocity deviates from the direction of radius,resulting in its lower radial component.The lower radial relative flow velocity leads to severe flow separation on the suction side near the trailing edge of the main blade.

The calculation of mechanical energy loss for incompressible steady pipe flow of homogeneous fluid

The calculation of the mechanical energy loss is one of the fundamental problems in the field of Hydraulics and Engineering Fluid Mechanics. However, for a non-uniform flow the relation between the mechanical energy loss in a volume of fluid and the kinematical and dynamical characteristics of the flow field is not clearly established. In this paper a new mechanical energy equation for the incompressible steady non-uniform pipe flow of homogeneous fluid is derived, which includes the variation of the mean turbulent kinetic energy, and the formula for the calculation of the mechanical energy transformation loss for the non-uniform flow between two cross sections is obtained based on this equation. This formula can be simplified to the Darcy-Weisbach formula for the uniform flow as widely used in Hydraulics. Furthermore, the contributions of the mechanical energy loss relative to the time averaged velocity gradient and the dissipation of the turbulent kinetic energy in the turbulent uniform pipe flow are discussed, and the contributions of the mechanical energy loss in the viscous sublayer, the buffer layer and the region above the buffer layer for the turbulent uniform flow are also analyzed.

Theoretical analysis and numerical simulation of mechanical energy loss and wall resistance of steady open channel flow

The mechanical energy loss and the wall resistance are very important in practical engineering. These problems are investigated through theoretical analysis and numerical simulation in this paper, The results are as follows. （1） A new mechanical energy equation for the total flow is obtained, and a general formula for the calculation of the mechanical energy loss is proposed. （2） The general relationship between the wall resistance and the mechanical energy loss for the steady channel flow is obtained, the simplified form of which for the steady uniform channel flow is in consistent with the formula used in Hydraulics deduced by 7r theorem and dimensional analysis. （3） The steady channel flow over a backward facing step with a small expansion ratio is numerica- lly simulated, and the mechanical energy loss, the wall resistance as well as the relationship between the wall resistance and the mechanical energy loss are calculated and analyzed.

Pushing the limits of microwave absorption capability of carbon fiber in fabric design based on genetic algorithm

The field of electromagnetic wave absorption(EWA)requires the adaptability,tenability,and multifunction of high-performance materials in the future.The design and preparation of EWA materials aiming at performance requirements is the latest research hotspot.Here,a performancedriven strategy for simultaneously coordinating different target performances was proposed to optimize the structure of the periodical long continuous carbon/glass fiber fabric(PCGF)materials through algorithm and simulation.The optimized structure of the PCGF not only improves the impedance matching,but also introduces the induced orientation effect for a high cooperative loss of conductivity,resonance,and periodic structure.The flexible PCGF shows a broad effective absorption bandwidth(EAB)of 32.7 GHz covering a part of the C-band and the whole X-,Ku-,K-,and Ka-bands with a thickness(d)of only 0.92 mm and a density of 5.6×10^(−4) kg·cm^(−3).This highly designable fabric is promising for the EWA practical application owing to integrating the characteristics of good flexibility,acid and alkali resistance,bending resistance,excellent mechanical properties,and easy large-scale preparation.

Numerical simulation of turbulent flow behind sluice gate under submerged discharge conditions

The turbulent flow discharging under a sluice gate is one kind of typical flows with complicated boundaries in hydraulic and hydroelectric engineering, and the characteristics of its flow field and flow evolution are important in engineering hydraulics. Although there were many studies in this regard, which mainly focus on the discharge capacity, the local scour and the mean flow field, some issues remain to be further investigated, for example, the variation of the mechanical energy during the scouring process, and the adjustment of the unsteady turbulent flow after the local scour with the downstream steady uniform flow. In this paper, the turbulent flow behind a sluice gate is divided into a rapidly varied flow region and a gradually varied flow region, and the above problems are investigated by theoretical analysis and numerical simulation. The main conclusions are as follows：（1） In the discharging process of the turbulent flow under a sluice gate, the river bed would be scoured continuously and the water–air interface is adjusted accordingly, which leads to a decrease of the mechanical energy of the total flow in the rapidly varied flow region, and the mechanical energy loss would also decrease with the increase of the time, yet the variation of the flow discharge under the sluice gate is very small.（2） In the link between the rapidly varied flow and the uniform flow downstream, the mean wall shear stress and the coefficient for the mechanical energy loss would decrease in the longitudinal direction, the decay of the turbulent kinetic energy near the free surface is much more significant than that near the bed in the longitudinal direction, and the mean turbulent kinetic energy in the section would decrease in the longitudinal direction and the decreasing rate is smaller than that of the mean wall shear stress.

A Critical Review of Real Gas Effects on the Regenerative Refrigerators

The regenerative refrigeration is an important reverse work-heat conversion cycle with a theoretical coefficient of performance(COP)identical to the Carnot efficiency.Practical regenerative refrigerators are capable of working down to 4 K and largely fulfill the refrigeration requirement of modern technologies in many fields,especially for space applications.However,the enthalpy flow associated with the pressure dependence,abbreviated as pressure-induced enthalpy flow,brought about by real gas effects degrades the theoretical COP of the refrigerator to below about 30% of the Carnot efficiency at the temperatures of below the critical point.This paper reviews the long history of exploring the real gas effects which dates back to the 1970 s and continues to now.Important explorations of uncovering the loss mechanism and reducing such losses are summarized.The theories that are in accordance with experimental results and simulation results are expounded.We further carry out analyses on the expansion components,including the pulse tube and the clearance gap.Several inferences are made in order to explore the long-lasting puzzles about real gas effects.It is emphasized that the underlying cause of the loss in the regenerator is an indirect effect of the real gas properties.Further study about carrying out a direct verification of the theory is proposed.

Hybrid approach for loss recovery mechanism in OBS networks

This letter reports a study of a hybrid burst assembly and a hybrid burst loss recovery scheme （delay-based burst assembly and hybrid loss recovery （DBAHLR）） which selectively employs proactive or reactive loss recovery techniques depending on the classification of traffic into short term and long term, respectively. Traffic prediction and segregation of optical burst switching network flows into the long term and short term are conducted based on predicted link holding times using the hidden Markov model （HMM）. The hybrid burst assembly implemented in DBAHLR uses a consecutive average-based burst assembly to handle jitter reduction necessary in real-time applications, with variations in burst sizes due to the non-monotonic nature of the average delay handled by additional burst length thresholding. This dynamic hybrid approach based on HMM prediction provides overall a lower blocking probability and delay and more throughput when compared with forward segment redundancy mechanism or purely HMM prediction-based adaptive burst sizing and wavelength allocation （HMM-TP）.

Entropy Generation Analysis around Airfoil using Multi-Block Lattice Boltzmann Method

This present paper proposes aerodynamic forces and entropy generation characteristics on theflow past two-dimensional airfoil at low Reynolds number by multiple-relaxation-time lattice Boltzmann method to clarify theflow loss mechanism.The block mesh refinement was adopted in which a higher accuracy was needed in parts of the domain characterized by complexflow.The interpolated bounce-back method was used to treat the irregular curve.This numerical method can effectively solve the complexflowfield simulation problems with reasonable accuracy and reli-ability by simulatingflow around plate and airfoil.Based on second law of thermo-dynamics,an expression of entropy generation rate for arbitrary control volume was derived theoretically which could accurately quantify the local irreversible loss of theflowfield at any position.After that,a comprehensive numerical study was conducted to analyze relationship of entropy generation and drag force by taking NACA0012 air-foil as the research object.For unsteady condition,entropy generation rate and the drag force are not linearly related any more.Losses due to steady effects mainly con-sider the irreversibility in the boundary layer and wake while the unsteady effects come from the interaction between the main separation vortex and the trailing shed-ding vortex.