Toarcian claystone such as that of the Callovo-Oxfordian is a qualified multiphase material. The claystone samples tested in this study are composed of four main mineral phases: silicates(clay minerals, quartz,feldspa...Toarcian claystone such as that of the Callovo-Oxfordian is a qualified multiphase material. The claystone samples tested in this study are composed of four main mineral phases: silicates(clay minerals, quartz,feldspars, micas)(z86%), sulphides(pyrite)(z3%), carbonates(calcite, dolomite)(z10%) and organic kerogen(z1%). Three sets of measurements of the modulus of deformability were compared as determined in(i) nanoindentation tests with a constant indentation depth of 2 mm,(ii) micro-indentation tests with a constant indentation depth of 20 mm, and(iii) meso-compression tests with a constant displacement of 200 mm. These three experimental methods have already been validated in earlier studies. The main objective of this study is to demonstrate the influence of the scaling effect on the modulus of deformability of the material. Different frequency distributions of the modulus of deformability were obtained at the different sample scales:(i) in nano-indentation tests, the distribution was spread between 15 GPa and 90 GPa and contained one peak at34 GPa and another at 51 GPa;(ii) in the micro-indentation tests, the distribution was spread between 25 GPa and 60 GPa and displayed peaks at 26 GPa and 37 GPa; and(iii) in the meso-compression tests, a narrow frequency distribution was obtained, ranging from 25 GPa to 50 GPa and with a maximum at around 35 GPa.展开更多
This study investigates the mechanical properties of Q235B steel through quasi-static tests at both room temperature and elevated temperature.The initial values of the Johnson-Cook model parameters are determined usin...This study investigates the mechanical properties of Q235B steel through quasi-static tests at both room temperature and elevated temperature.The initial values of the Johnson-Cook model parameters are determined using a fitting method.The global response surface algorithm is employed to optimize and calibrate the Johnson-Cook model parameters for Q235B steel under both room temperature and elevated temperature conditions.A simulation model is established at room temperature,and the simulated mechanical performance curves for displacement and stress are monitored.Multiple optimization algorithms are applied to optimize and calibrate the model parameters at room temperature.The global response surface algorithm is identified as the most suitable algorithm for this optimization problem.Sensitivity analysis is conducted to explore the impact of model parameters on the objective function.The analysis indicates that the optimized material model better fits the experimental values,aligning more closely with the actual test results of material strain mechanisms over a wide temperature range.展开更多
The present study focuses on the formulation of new composite consisting of plaster and raffia vinifera particle (RVP) with the purpose to reducing energy consumption. The aim of this study is to test this new compoun...The present study focuses on the formulation of new composite consisting of plaster and raffia vinifera particle (RVP) with the purpose to reducing energy consumption. The aim of this study is to test this new compound as an insulating eco-material in building in a tropical climate. The composites samples were developed by mixing plaster with raffia vinifera particles (RVP) using three different sizes (1.6 mm, 2.5 mm and 4 mm). The effects of four different RVP incorporations rates (i.e., 0wt%, 5wt%;10wt%;15wt%) on physical, thermal, mechanicals properties of the composites were investigated. In addition, the use of the raffia vinifera particles and plaster based composite material as building envelopes thermal insulation material is studied by the habitable cell thermal behavior instrumentation. The results indicate that the incorporation of raffia vinifera particle leads to improve the new composite physical, mechanical and thermal properties. And the parametric analysis reveals that the sampling rate and the size of raffia vinifera particles are the most decisive factor to impact these properties, and to decreases in the thermal conductivity which leads to an improvement to the thermal resistance and energy savings. The best improvement of plaster composite was obtained at the raffia vinifera particles size between 2.5 and 4.0 mm loading of 5wt% (C95P5R) with a good ratio of thermo-physical-mechanical properties. Additionally, the habitable cell experimental thermal behavior, with the new raffia vinifera particles and plaster-based composite as thermal insulating material for building walls, gives an average damping of 4°C and 5.8°C in the insulated house interior environment respectively for cold and hot cases compared to the outside environment and the uninsulated house interior environment. The current study highlights that this mixture gives the new composite thermal insulation properties applicable in the eco-construction of habitats in tropical environments.展开更多
Natural fiber-reinforced hybrid composites can be a better replacement for plastic composites since these plastic composites pose a serious threat to the environment.The aim of this study is to analyze the effect of s...Natural fiber-reinforced hybrid composites can be a better replacement for plastic composites since these plastic composites pose a serious threat to the environment.The aim of this study is to analyze the effect of surface modification of the natural fibers on the mechanical,thermal,hygrothermal,and water absorption behaviors of flax,sisal,and glass fiber-reinforced epoxy hybrid composites.The mechanical properties of alkaline treated sisal and flax fibers were found to increase considerably.Tensile,flexural and impact strength of glass/flax-fiber-reinforced hybrid samples improved by 58%,36%,and 51%,respectively,after surface alkaline treatment.In addition,the hygrothermal analysis and water absorption capacity are studied and also the Interfacial bonding properties were analyzed using Scanning Electron Microscopic images.The thermal analysis using thermogravimetric analyzer reveals that the decomposition temperature for hybrid fiber reinforced composites are between 306 and 312℃.In conclusion,surface treatment improves the performance of natural fiber in hybrid fiber-reinforced composites,particularly flax fiber.展开更多
Mechanical properties of silicon nanobeams are of prime importance in nanoelectromechanical system applications. A numerical experimental method of determining resonant frequencies and Young's modulus of nanobeams by...Mechanical properties of silicon nanobeams are of prime importance in nanoelectromechanical system applications. A numerical experimental method of determining resonant frequencies and Young's modulus of nanobeams by combining finite element analysis and frequency response tests based on an electrostatic excitation and visual detection by using a laser Doppler vibrometer is presented in this paper. Silicon nanobeam test structures are fabricated from silicon-oninsulator wafers by using a standard lithography and anisotropic wet etching release process, which inevitably generates the undercut of the nanobeam clamping. In conjunction with three-dimensional finite element numerical simulations incorporating the geometric undercut, dynamic resonance tests reveal that the undercut significantly reduces resonant frequencies of nanobeams due to the fact that it effectively increases the nanobeam length by a correct value △L, which is a key parameter that is correlated with deviations in the resonant frequencies predicted from the ideal Euler-Bernoulli beam theory and experimentally measured data. By using a least-square fit expression including △L, we finally extract Young's modulus from the measured resonance frequency versus effective length dependency and find that Young's modulus of a silicon nanobeam with 200-nm thickness is close to that of bulk silicon. This result supports that the finite size effect due to the surface effect does not play a role in the mechanical elastic behaviour of silicon nanobeams with thickness larger than 200 nm.展开更多
In this work,the microstructural and mechanical properties of the certain magnesium-based alloys were investigated.The alloys were produced under a controlled atmosphere by a squeeze-casting process and characterized ...In this work,the microstructural and mechanical properties of the certain magnesium-based alloys were investigated.The alloys were produced under a controlled atmosphere by a squeeze-casting process and characterized by optical microscopy(OM),scanning electron microscopy(SEM),an energy-dispersive spectrometer(EDS)and X-ray diffraction(XRD)analysis.The results indicated that the addition of strontium element modified the structure and refined the grain size.The hardness and yield strength of the alloys increased continuously with increasing strontium content,while the elongation was gradually decreased.Also,the tensile strength value of the based alloy was increased by adding Sr up to 1 wt.%.After more addition of Sr,the tensile strength starts to diminish.展开更多
In order to verify the influence of different block proportions S/B on the effect of SBS modified asphalt,the dynamic mechanical performance test and static loading test were performed on the samples composed of diffe...In order to verify the influence of different block proportions S/B on the effect of SBS modified asphalt,the dynamic mechanical performance test and static loading test were performed on the samples composed of different kinds of SBS with base asphalt. It is found that different S/B values fix on different modified effects and different viscoelastic mechanical behaviors,due to biphasic separate fabric of polybutadiene and polystyrene in SBS. In low-speed running pavement,the modified asphalt with lower S/B value shows better pavement performance,while in high-speed running pavement,the modified asphalt with higher S/B value shows better pavement performance. As far as SBS modified asphalt itself is concerned,mixing proportion impacts on resisting displacement and block proportion S/B ratio impacts on strain recovery capacity. In the case that the conditions are the same,SBS modified asphalt with different S/B values can be used for different travelling speed pavement construction demands to get an intelligent use.展开更多
To solve the problems of blindness and inefficiency existing in the determination of meso-level mechanical parameters of particle flow code (PFC) models, we firstly designed and numerically carried out orthogonal test...To solve the problems of blindness and inefficiency existing in the determination of meso-level mechanical parameters of particle flow code (PFC) models, we firstly designed and numerically carried out orthogonal tests on rock samples to investigate the correlations between macro-and meso-level mechanical parameters of rock-like bonded granular materials. Then based on the artificial intelligent technology, the intelligent prediction systems for nine meso-level mechanical parameters of PFC models were obtained by creating, training and testing the prediction models with the set of data got from the orthogonal tests. Lastly the prediction systems were used to predict the meso-level mechanical parameters of one kind of sandy mudstone, and according to the predicted results the macroscopic properties of the rock were obtained by numerical tests. The maximum relative error between the numerical test results and real rock properties is 3.28% which satisfies the precision requirement in engineering. It shows that this paper provides a fast and accurate method for the determination of meso-level mechanical parameters of PFC models.展开更多
The in-soil biodegradation of Stipa tenacissima(alfa)leaves was examined.Non-linear mechanical testing was performed at various biodegradation stages.Tensile strength,loading and unloading Young’s moduli and dissipat...The in-soil biodegradation of Stipa tenacissima(alfa)leaves was examined.Non-linear mechanical testing was performed at various biodegradation stages.Tensile strength,loading and unloading Young’s moduli and dissipation energy decreased with the burial time,whereas plasticity increased.Field-emission scanning electron microscopy(FE-SEM)showed that the fracture cracks propagated in the longitudinal direction in the raw material,resulting in a fracture mode consisting of a mixture of middle lamella delamination and fiber pull-out.In contrast,the cracks were perpendicular to the stem axis in the biodegraded material,demonstrating an important strength loss of the load-bearing fibers.This strength loss was correlated with rapid cellulose degradation.A novel X-ray diffraction(XRD)model was implemented in order to take into account anisotropic size broadening.For the first time,XRD demonstrated the action of biodegradation on unrefined plant tissues under quasi in-situ conditions.Biodegradation induced a progressive loss of crystalline cellulose accompanied with anisotropic crystallite thinning.展开更多
Aground firing test of the Chang'e 3 lander was conducted recently to check the mechanical performance of the spacecraft. The test was vital before the propulsion system test of the Chang'e 3 lander and was al...Aground firing test of the Chang'e 3 lander was conducted recently to check the mechanical performance of the spacecraft. The test was vital before the propulsion system test of the Chang'e 3 lander and was also a very important precondition to verify whether the propulsion system design could meet the requirements for in-orbit operation.展开更多
We studied the microstructure evolution of Mg-4Y-3Nd-2Sm-0.5Zr alloy by quasi-in-situ electron backscatter diffraction(EBSD)along with several strains under compression tests,which provided direct evidence for the inf...We studied the microstructure evolution of Mg-4Y-3Nd-2Sm-0.5Zr alloy by quasi-in-situ electron backscatter diffraction(EBSD)along with several strains under compression tests,which provided direct evidence for the influence of different twin-twin geometric structure on the twinning behavior.The results showed that the mechanical properties of the alloy were higher than traditional magnesium alloys(the maximum compressive strength reaches 402.5 MPa)due to the strengthening effect of Sm and Nd elements addition on solution strengthening,precipitation strengthening,and grain refinement.Combined with the quasi-in-situ EBSD technique,two different twin-twin geometric structures,‘parallel structure’and‘cross structure’,were observed directly in the alloy.In the later stage of deformation,for‘parallel structure’,residual stress and a large number of dislocations mainly existed in the twin boundary and tip position.For the‘cross structure’,there was a lot of dislocation density in the interior of twins after fusion.The twin growth rate of‘parallel structure’was much faster than that of‘cross structure’because the stress of twins was mainly concentrated on the tip of twin.When the movement for the tip of twin was blocked,the growth rate of twin would be obviously decreased.Moreover,the‘cross structure’was easy to produce closed space.Due to the constraints of surrounding twins,the confined space was easy to stress concentration,thus inhibiting the growth of twins.At the same time,the‘cross structure’of twins needed a more external force to continue to deform,which also served as a strengthening structure.展开更多
Using the results of physical and chemical researches and mechanical tests of the Pd-Au-Cu-Sn system alloys, a new palladium-based alloy has been chosen and studied in detail. It has a higher plasticity and a lower ha...Using the results of physical and chemical researches and mechanical tests of the Pd-Au-Cu-Sn system alloys, a new palladium-based alloy has been chosen and studied in detail. It has a higher plasticity and a lower hardness than the Palladent alloy, widely used in prosthetic dentistry: its hardness is lower than 300 MPa, and its specific elongation is 10%~14 %. At the same time, such important practical characteristics of the alloys as the strength of adhesion to ceramics and thermal expansion coefficient are almost similar.展开更多
The spatial and temproal evolution of strain. fault displacement and acoustic emissions during deformation of fault systems with different geometrical textures are studied experimentally under biaxial compresison, and...The spatial and temproal evolution of strain. fault displacement and acoustic emissions during deformation of fault systems with different geometrical textures are studied experimentally under biaxial compresison, and the characteristics of typical instability events are analysed. The results show that fault systems with different geometrical textures have different evolutional images of physical field during deformation. Based on the characteristics of physical field and the deformation mechanism, various types of instability - two types of stick-slip, fracturing type and mixed type instability can be recognized. Different types of instability differ clearly in their precursors, and the instability type is closely related with the geometrical texture and the deformation stage of the fault system. Therefore, it is very significant for earthquake prediction and precursor analysis to investigatethe geometrical textures of natural active faults.展开更多
Many structures and materials in nature and physiology have important "meso-scale" structures at the micron lengthscale whose tensile responses have proven difficult to characterize mechanically. Although techniques...Many structures and materials in nature and physiology have important "meso-scale" structures at the micron lengthscale whose tensile responses have proven difficult to characterize mechanically. Although techniques such as atomic force microscopy and micro- and nano-identation are mature for compression and indentation testing at the nano-scale, and standard uniaxial and shear rheometry techniques exist for the macroscale, few techniques are applicable for tensile-testing at the micrometre-scale, leaving a gap in our understanding of hierarchical biomaterials. Here, we present a novel magnetic mechanical testing (MMT) system that enables viscoelastic tensile testing at this critical length scale. The MMT system applies non-contact loading, avoiding gripping and surface interaction effects. We demonstrate application of the MMT system to the first analyses of the pure tensile responses of several native and engineered tissue systems at the mesoscale, showing the broad potential of the system for exploring micro- and meso-scale analysis of structured and hierarchical biological systems.展开更多
Friction Stir Welding(FSW)is the most promising solid-state metals joining method introduced in this era.Compared to the conventional fusion welding methods,this FSW can produce joints with higher mechanical and metal...Friction Stir Welding(FSW)is the most promising solid-state metals joining method introduced in this era.Compared to the conventional fusion welding methods,this FSW can produce joints with higher mechanical and metallurgi-cal properties.Formerly,FSW was adopted for low melting metals like aluminum alloys.In recent years it has made significant progress in friction stir welding of steels since unfavourable phase transformations occurred in welds due to the melting of the parent and filler metals in fusion welding can be eliminated.The main advantage of FSW over traditional fusion welding is the reduction in the heat-affected zone(HAZ),and the joints exhibit excellent mechanical and corrosion resistance properties.This article reviews the progress in the relevant issues such as the FSW tool mate-rials and tool profiles for joining steels,microstructure and mechanical properties of steels joints,special problems in joining dissimilar steels.Moreover,in-situ heating sources was used to overcome the main limitations in FSW of hard metals and their alloys,i.e.,tool damages and insufficient heat generation.Different in-situ heating sources like laser,induction heat,gas tungsten arc welding assisted FSW for various types of steels are introduced in this review.On the basis of the up-to-date status,some problems that need further investigation are put forward.展开更多
A statistical theory of disperse damage of materials gained under loading is proposed. It is based on the idea of distribution of potential damage spots within a specimen similar to the distribution of the strength va...A statistical theory of disperse damage of materials gained under loading is proposed. It is based on the idea of distribution of potential damage spots within a specimen similar to the distribution of the strength values found by testing a set of identical specimens. A relation between damage risk and the probability of damage of a single specimen is assumed. It conforms to the relation between risk and probability of strength distribution of a set of identical specimens, according to Weibull’s statistical theory of material strength. The damage risk just like the damage probability are assumed to be functions of loading and time. Damage is modeled regarding two mechanisms—thermo-fluctuation damage based on the kinetic theory of material strength, and damage depending on a parameter called loading degree (percentage), which depends on load and time. The first mechanism adopts two relations regarding energy barrier reduction due to loading. Equations of damage advance under short-term loading (with a constant rate of load increase) and under long-term (constant) loading are derived. Theoretical relations of damage development are compared with experimental evidence gained via specific tests on short glass fibre reinforced polyoximethylene. The damage itself consists of the accumulation of additional internal surfaces within the entire material volume as measured by small angle scattering X-ray refractometry. It is shown that the mechanism of damage as a function of loading degree where time participates implicitly, gains advantage over the kinetic mechanism where time is explicitly present. The cumulative functions derived for damage accumulation can be used to assess not only damage, but also for statistical analysis of the strength and other quantities.展开更多
Mobarakeh Steel Company produces 3 million tons of steel annually with eight 180 tons EBT furnaces. Different types of magnesia-carbon refractories have been employed at slagline during last 5 years. In the present st...Mobarakeh Steel Company produces 3 million tons of steel annually with eight 180 tons EBT furnaces. Different types of magnesia-carbon refractories have been employed at slagline during last 5 years. In the present study the wear and corrosion of MgO-C refractories of these furnaces have been studied via post-mortem analysis of used bricks and the observation of operational effects. Laboratory corrosion tests were also arranged to investigate the effect of slag chemistry and the mechanism of chemical corrosion . Characterization of different magnesia-carbon bricks clarified that the crystal size , type and chemistry of magnesia as well as graphite structure have the main influence on corrosion resistance. The CaO: SiO2 ratio in slag also plays a vital role in the wear of slagline refractories. The iron oxide content of slag also has a major role in graphite oxidation. Of metallurgical parameters , the electric power input and the contact time have great influence on refractories life. The results will be discussed with emphasis on particular operational factors in Mobarakeh steel plant.展开更多
The corrosion failure mechanism of M152 was studied using the neutral salt-spray test to better understand the corrosion behavior of 1Cr12Ni3Mo2VN(M152), provide a basis for the optimization of material selection, a...The corrosion failure mechanism of M152 was studied using the neutral salt-spray test to better understand the corrosion behavior of 1Cr12Ni3Mo2VN(M152), provide a basis for the optimization of material selection, and prevent the occurrence of failure. Moreover, the mechanism was investigated using the mass loss method, polarization curves, electrochemical impedance spectroscopy(EIS), stereology microscopy, scanning electron microscopy, and energy-dispersive X-ray spectroscopy(EDS). The results show that M152 steel suffers severe corrosion, especially pitting corrosion, in a high-salt-spray environment. In the early stage of the experiment, the color of the corrosion products was mainly orange. The products then gradually evolved into a dense, brown substance, which coincided with a decrease of corrosion rate. Correspondingly, the EIS spectrum of M152 in the late test also exhibited three time constants and presented Warburg impedance at low frequencies.展开更多
With the continuous development of today's science and technology,orthopedic research has also achieved continuous updates in materials and machinery.In this case,the mechanics testing technology of orthopedics al...With the continuous development of today's science and technology,orthopedic research has also achieved continuous updates in materials and machinery.In this case,the mechanics testing technology of orthopedics also needs to be further updated and developed,so that it can effectively meet the requirement for today's orthopedic mechanical testing.Based on this,this article analyzes several advanced orthopedic mechanics testing techniques.It is hoped that this analysis can provide a reference for the good application and development of orthopedic mechanics testing technology.展开更多
Bell tests with entangled light have been performed many times in many ways using linear polarizers, but the same tests have never been done with a circular polarizer. Until recently there has never been a true circul...Bell tests with entangled light have been performed many times in many ways using linear polarizers, but the same tests have never been done with a circular polarizer. Until recently there has never been a true circular polarization beamsplitter—an optical component that separates light directly into left and right handed polarizations. Using a true circular polarization beamsplitter based on birefringent gratings, entangled light has been analyzed with unexpected results.展开更多
文摘Toarcian claystone such as that of the Callovo-Oxfordian is a qualified multiphase material. The claystone samples tested in this study are composed of four main mineral phases: silicates(clay minerals, quartz,feldspars, micas)(z86%), sulphides(pyrite)(z3%), carbonates(calcite, dolomite)(z10%) and organic kerogen(z1%). Three sets of measurements of the modulus of deformability were compared as determined in(i) nanoindentation tests with a constant indentation depth of 2 mm,(ii) micro-indentation tests with a constant indentation depth of 20 mm, and(iii) meso-compression tests with a constant displacement of 200 mm. These three experimental methods have already been validated in earlier studies. The main objective of this study is to demonstrate the influence of the scaling effect on the modulus of deformability of the material. Different frequency distributions of the modulus of deformability were obtained at the different sample scales:(i) in nano-indentation tests, the distribution was spread between 15 GPa and 90 GPa and contained one peak at34 GPa and another at 51 GPa;(ii) in the micro-indentation tests, the distribution was spread between 25 GPa and 60 GPa and displayed peaks at 26 GPa and 37 GPa; and(iii) in the meso-compression tests, a narrow frequency distribution was obtained, ranging from 25 GPa to 50 GPa and with a maximum at around 35 GPa.
文摘This study investigates the mechanical properties of Q235B steel through quasi-static tests at both room temperature and elevated temperature.The initial values of the Johnson-Cook model parameters are determined using a fitting method.The global response surface algorithm is employed to optimize and calibrate the Johnson-Cook model parameters for Q235B steel under both room temperature and elevated temperature conditions.A simulation model is established at room temperature,and the simulated mechanical performance curves for displacement and stress are monitored.Multiple optimization algorithms are applied to optimize and calibrate the model parameters at room temperature.The global response surface algorithm is identified as the most suitable algorithm for this optimization problem.Sensitivity analysis is conducted to explore the impact of model parameters on the objective function.The analysis indicates that the optimized material model better fits the experimental values,aligning more closely with the actual test results of material strain mechanisms over a wide temperature range.
文摘The present study focuses on the formulation of new composite consisting of plaster and raffia vinifera particle (RVP) with the purpose to reducing energy consumption. The aim of this study is to test this new compound as an insulating eco-material in building in a tropical climate. The composites samples were developed by mixing plaster with raffia vinifera particles (RVP) using three different sizes (1.6 mm, 2.5 mm and 4 mm). The effects of four different RVP incorporations rates (i.e., 0wt%, 5wt%;10wt%;15wt%) on physical, thermal, mechanicals properties of the composites were investigated. In addition, the use of the raffia vinifera particles and plaster based composite material as building envelopes thermal insulation material is studied by the habitable cell thermal behavior instrumentation. The results indicate that the incorporation of raffia vinifera particle leads to improve the new composite physical, mechanical and thermal properties. And the parametric analysis reveals that the sampling rate and the size of raffia vinifera particles are the most decisive factor to impact these properties, and to decreases in the thermal conductivity which leads to an improvement to the thermal resistance and energy savings. The best improvement of plaster composite was obtained at the raffia vinifera particles size between 2.5 and 4.0 mm loading of 5wt% (C95P5R) with a good ratio of thermo-physical-mechanical properties. Additionally, the habitable cell experimental thermal behavior, with the new raffia vinifera particles and plaster-based composite as thermal insulating material for building walls, gives an average damping of 4°C and 5.8°C in the insulated house interior environment respectively for cold and hot cases compared to the outside environment and the uninsulated house interior environment. The current study highlights that this mixture gives the new composite thermal insulation properties applicable in the eco-construction of habitats in tropical environments.
文摘Natural fiber-reinforced hybrid composites can be a better replacement for plastic composites since these plastic composites pose a serious threat to the environment.The aim of this study is to analyze the effect of surface modification of the natural fibers on the mechanical,thermal,hygrothermal,and water absorption behaviors of flax,sisal,and glass fiber-reinforced epoxy hybrid composites.The mechanical properties of alkaline treated sisal and flax fibers were found to increase considerably.Tensile,flexural and impact strength of glass/flax-fiber-reinforced hybrid samples improved by 58%,36%,and 51%,respectively,after surface alkaline treatment.In addition,the hygrothermal analysis and water absorption capacity are studied and also the Interfacial bonding properties were analyzed using Scanning Electron Microscopic images.The thermal analysis using thermogravimetric analyzer reveals that the decomposition temperature for hybrid fiber reinforced composites are between 306 and 312℃.In conclusion,surface treatment improves the performance of natural fiber in hybrid fiber-reinforced composites,particularly flax fiber.
基金Project supported by the National Natural Science Foundation of China (Grant Nos. 41075026 and 61001044)the Open Re-search Fund of Key Laboratory of Microelectromechanical System of Ministry of Education,Southeast University,China (Grant Nos. 2009-03 and 2010-02)+1 种基金the Special Fund for Meteorology Research in the Public Interest,China (Grant No. GYHY200906037)the Priority Academic Program Development of Sensor Networks and Modern Meteorological Equipment of Jiangsu Provincial Higher Education Institutions
文摘Mechanical properties of silicon nanobeams are of prime importance in nanoelectromechanical system applications. A numerical experimental method of determining resonant frequencies and Young's modulus of nanobeams by combining finite element analysis and frequency response tests based on an electrostatic excitation and visual detection by using a laser Doppler vibrometer is presented in this paper. Silicon nanobeam test structures are fabricated from silicon-oninsulator wafers by using a standard lithography and anisotropic wet etching release process, which inevitably generates the undercut of the nanobeam clamping. In conjunction with three-dimensional finite element numerical simulations incorporating the geometric undercut, dynamic resonance tests reveal that the undercut significantly reduces resonant frequencies of nanobeams due to the fact that it effectively increases the nanobeam length by a correct value △L, which is a key parameter that is correlated with deviations in the resonant frequencies predicted from the ideal Euler-Bernoulli beam theory and experimentally measured data. By using a least-square fit expression including △L, we finally extract Young's modulus from the measured resonance frequency versus effective length dependency and find that Young's modulus of a silicon nanobeam with 200-nm thickness is close to that of bulk silicon. This result supports that the finite size effect due to the surface effect does not play a role in the mechanical elastic behaviour of silicon nanobeams with thickness larger than 200 nm.
基金The authors wish to thank The Scientific and Technical Research Council of Turkey-TUBITAK(grant number:106M122)for financial support in this study.The authors also would like to thank Mr.Metin GUNAY for his technical support.
文摘In this work,the microstructural and mechanical properties of the certain magnesium-based alloys were investigated.The alloys were produced under a controlled atmosphere by a squeeze-casting process and characterized by optical microscopy(OM),scanning electron microscopy(SEM),an energy-dispersive spectrometer(EDS)and X-ray diffraction(XRD)analysis.The results indicated that the addition of strontium element modified the structure and refined the grain size.The hardness and yield strength of the alloys increased continuously with increasing strontium content,while the elongation was gradually decreased.Also,the tensile strength value of the based alloy was increased by adding Sr up to 1 wt.%.After more addition of Sr,the tensile strength starts to diminish.
基金Sponsored by the National Natural Science Foundation of China (Grant No. 50008005)
文摘In order to verify the influence of different block proportions S/B on the effect of SBS modified asphalt,the dynamic mechanical performance test and static loading test were performed on the samples composed of different kinds of SBS with base asphalt. It is found that different S/B values fix on different modified effects and different viscoelastic mechanical behaviors,due to biphasic separate fabric of polybutadiene and polystyrene in SBS. In low-speed running pavement,the modified asphalt with lower S/B value shows better pavement performance,while in high-speed running pavement,the modified asphalt with higher S/B value shows better pavement performance. As far as SBS modified asphalt itself is concerned,mixing proportion impacts on resisting displacement and block proportion S/B ratio impacts on strain recovery capacity. In the case that the conditions are the same,SBS modified asphalt with different S/B values can be used for different travelling speed pavement construction demands to get an intelligent use.
基金the National Natural Science Foundation of China (Nos. 50674083 and 51074162) for its financial support
文摘To solve the problems of blindness and inefficiency existing in the determination of meso-level mechanical parameters of particle flow code (PFC) models, we firstly designed and numerically carried out orthogonal tests on rock samples to investigate the correlations between macro-and meso-level mechanical parameters of rock-like bonded granular materials. Then based on the artificial intelligent technology, the intelligent prediction systems for nine meso-level mechanical parameters of PFC models were obtained by creating, training and testing the prediction models with the set of data got from the orthogonal tests. Lastly the prediction systems were used to predict the meso-level mechanical parameters of one kind of sandy mudstone, and according to the predicted results the macroscopic properties of the rock were obtained by numerical tests. The maximum relative error between the numerical test results and real rock properties is 3.28% which satisfies the precision requirement in engineering. It shows that this paper provides a fast and accurate method for the determination of meso-level mechanical parameters of PFC models.
文摘The in-soil biodegradation of Stipa tenacissima(alfa)leaves was examined.Non-linear mechanical testing was performed at various biodegradation stages.Tensile strength,loading and unloading Young’s moduli and dissipation energy decreased with the burial time,whereas plasticity increased.Field-emission scanning electron microscopy(FE-SEM)showed that the fracture cracks propagated in the longitudinal direction in the raw material,resulting in a fracture mode consisting of a mixture of middle lamella delamination and fiber pull-out.In contrast,the cracks were perpendicular to the stem axis in the biodegraded material,demonstrating an important strength loss of the load-bearing fibers.This strength loss was correlated with rapid cellulose degradation.A novel X-ray diffraction(XRD)model was implemented in order to take into account anisotropic size broadening.For the first time,XRD demonstrated the action of biodegradation on unrefined plant tissues under quasi in-situ conditions.Biodegradation induced a progressive loss of crystalline cellulose accompanied with anisotropic crystallite thinning.
文摘Aground firing test of the Chang'e 3 lander was conducted recently to check the mechanical performance of the spacecraft. The test was vital before the propulsion system test of the Chang'e 3 lander and was also a very important precondition to verify whether the propulsion system design could meet the requirements for in-orbit operation.
基金supported by the National Natural Sci-ence Foundation of China(Grant no.51571084)financial support from the China Scholarship Council(Grant No.201908410208).
文摘We studied the microstructure evolution of Mg-4Y-3Nd-2Sm-0.5Zr alloy by quasi-in-situ electron backscatter diffraction(EBSD)along with several strains under compression tests,which provided direct evidence for the influence of different twin-twin geometric structure on the twinning behavior.The results showed that the mechanical properties of the alloy were higher than traditional magnesium alloys(the maximum compressive strength reaches 402.5 MPa)due to the strengthening effect of Sm and Nd elements addition on solution strengthening,precipitation strengthening,and grain refinement.Combined with the quasi-in-situ EBSD technique,two different twin-twin geometric structures,‘parallel structure’and‘cross structure’,were observed directly in the alloy.In the later stage of deformation,for‘parallel structure’,residual stress and a large number of dislocations mainly existed in the twin boundary and tip position.For the‘cross structure’,there was a lot of dislocation density in the interior of twins after fusion.The twin growth rate of‘parallel structure’was much faster than that of‘cross structure’because the stress of twins was mainly concentrated on the tip of twin.When the movement for the tip of twin was blocked,the growth rate of twin would be obviously decreased.Moreover,the‘cross structure’was easy to produce closed space.Due to the constraints of surrounding twins,the confined space was easy to stress concentration,thus inhibiting the growth of twins.At the same time,the‘cross structure’of twins needed a more external force to continue to deform,which also served as a strengthening structure.
文摘Using the results of physical and chemical researches and mechanical tests of the Pd-Au-Cu-Sn system alloys, a new palladium-based alloy has been chosen and studied in detail. It has a higher plasticity and a lower hardness than the Palladent alloy, widely used in prosthetic dentistry: its hardness is lower than 300 MPa, and its specific elongation is 10%~14 %. At the same time, such important practical characteristics of the alloys as the strength of adhesion to ceramics and thermal expansion coefficient are almost similar.
文摘The spatial and temproal evolution of strain. fault displacement and acoustic emissions during deformation of fault systems with different geometrical textures are studied experimentally under biaxial compresison, and the characteristics of typical instability events are analysed. The results show that fault systems with different geometrical textures have different evolutional images of physical field during deformation. Based on the characteristics of physical field and the deformation mechanism, various types of instability - two types of stick-slip, fracturing type and mixed type instability can be recognized. Different types of instability differ clearly in their precursors, and the instability type is closely related with the geometrical texture and the deformation stage of the fault system. Therefore, it is very significant for earthquake prediction and precursor analysis to investigatethe geometrical textures of natural active faults.
基金partially supported by the National Natural Science Foundation of China(Grants 11532009,11372243,and 11522219)the China Postdoctoral Science Foundation(Grant 2016M602810)This project was also supported by the Initiative Postdocs Supporting Program(Grant BX201600121)
文摘Many structures and materials in nature and physiology have important "meso-scale" structures at the micron lengthscale whose tensile responses have proven difficult to characterize mechanically. Although techniques such as atomic force microscopy and micro- and nano-identation are mature for compression and indentation testing at the nano-scale, and standard uniaxial and shear rheometry techniques exist for the macroscale, few techniques are applicable for tensile-testing at the micrometre-scale, leaving a gap in our understanding of hierarchical biomaterials. Here, we present a novel magnetic mechanical testing (MMT) system that enables viscoelastic tensile testing at this critical length scale. The MMT system applies non-contact loading, avoiding gripping and surface interaction effects. We demonstrate application of the MMT system to the first analyses of the pure tensile responses of several native and engineered tissue systems at the mesoscale, showing the broad potential of the system for exploring micro- and meso-scale analysis of structured and hierarchical biological systems.
基金Supported by National Natural Science Foundation of China(Grant No.51842507).
文摘Friction Stir Welding(FSW)is the most promising solid-state metals joining method introduced in this era.Compared to the conventional fusion welding methods,this FSW can produce joints with higher mechanical and metallurgi-cal properties.Formerly,FSW was adopted for low melting metals like aluminum alloys.In recent years it has made significant progress in friction stir welding of steels since unfavourable phase transformations occurred in welds due to the melting of the parent and filler metals in fusion welding can be eliminated.The main advantage of FSW over traditional fusion welding is the reduction in the heat-affected zone(HAZ),and the joints exhibit excellent mechanical and corrosion resistance properties.This article reviews the progress in the relevant issues such as the FSW tool mate-rials and tool profiles for joining steels,microstructure and mechanical properties of steels joints,special problems in joining dissimilar steels.Moreover,in-situ heating sources was used to overcome the main limitations in FSW of hard metals and their alloys,i.e.,tool damages and insufficient heat generation.Different in-situ heating sources like laser,induction heat,gas tungsten arc welding assisted FSW for various types of steels are introduced in this review.On the basis of the up-to-date status,some problems that need further investigation are put forward.
文摘A statistical theory of disperse damage of materials gained under loading is proposed. It is based on the idea of distribution of potential damage spots within a specimen similar to the distribution of the strength values found by testing a set of identical specimens. A relation between damage risk and the probability of damage of a single specimen is assumed. It conforms to the relation between risk and probability of strength distribution of a set of identical specimens, according to Weibull’s statistical theory of material strength. The damage risk just like the damage probability are assumed to be functions of loading and time. Damage is modeled regarding two mechanisms—thermo-fluctuation damage based on the kinetic theory of material strength, and damage depending on a parameter called loading degree (percentage), which depends on load and time. The first mechanism adopts two relations regarding energy barrier reduction due to loading. Equations of damage advance under short-term loading (with a constant rate of load increase) and under long-term (constant) loading are derived. Theoretical relations of damage development are compared with experimental evidence gained via specific tests on short glass fibre reinforced polyoximethylene. The damage itself consists of the accumulation of additional internal surfaces within the entire material volume as measured by small angle scattering X-ray refractometry. It is shown that the mechanism of damage as a function of loading degree where time participates implicitly, gains advantage over the kinetic mechanism where time is explicitly present. The cumulative functions derived for damage accumulation can be used to assess not only damage, but also for statistical analysis of the strength and other quantities.
文摘Mobarakeh Steel Company produces 3 million tons of steel annually with eight 180 tons EBT furnaces. Different types of magnesia-carbon refractories have been employed at slagline during last 5 years. In the present study the wear and corrosion of MgO-C refractories of these furnaces have been studied via post-mortem analysis of used bricks and the observation of operational effects. Laboratory corrosion tests were also arranged to investigate the effect of slag chemistry and the mechanism of chemical corrosion . Characterization of different magnesia-carbon bricks clarified that the crystal size , type and chemistry of magnesia as well as graphite structure have the main influence on corrosion resistance. The CaO: SiO2 ratio in slag also plays a vital role in the wear of slagline refractories. The iron oxide content of slag also has a major role in graphite oxidation. Of metallurgical parameters , the electric power input and the contact time have great influence on refractories life. The results will be discussed with emphasis on particular operational factors in Mobarakeh steel plant.
基金financially supported by the Major State Basic Research Development Program of China (No. 2014CB643300)
文摘The corrosion failure mechanism of M152 was studied using the neutral salt-spray test to better understand the corrosion behavior of 1Cr12Ni3Mo2VN(M152), provide a basis for the optimization of material selection, and prevent the occurrence of failure. Moreover, the mechanism was investigated using the mass loss method, polarization curves, electrochemical impedance spectroscopy(EIS), stereology microscopy, scanning electron microscopy, and energy-dispersive X-ray spectroscopy(EDS). The results show that M152 steel suffers severe corrosion, especially pitting corrosion, in a high-salt-spray environment. In the early stage of the experiment, the color of the corrosion products was mainly orange. The products then gradually evolved into a dense, brown substance, which coincided with a decrease of corrosion rate. Correspondingly, the EIS spectrum of M152 in the late test also exhibited three time constants and presented Warburg impedance at low frequencies.
文摘With the continuous development of today's science and technology,orthopedic research has also achieved continuous updates in materials and machinery.In this case,the mechanics testing technology of orthopedics also needs to be further updated and developed,so that it can effectively meet the requirement for today's orthopedic mechanical testing.Based on this,this article analyzes several advanced orthopedic mechanics testing techniques.It is hoped that this analysis can provide a reference for the good application and development of orthopedic mechanics testing technology.
文摘Bell tests with entangled light have been performed many times in many ways using linear polarizers, but the same tests have never been done with a circular polarizer. Until recently there has never been a true circular polarization beamsplitter—an optical component that separates light directly into left and right handed polarizations. Using a true circular polarization beamsplitter based on birefringent gratings, entangled light has been analyzed with unexpected results.