Study of energy-efficient heat resistance and cooling technology for high temperature working face with multiple heat sources in deep mine

In the present research,we proposed a scheme to address the issues of severe heat damage,high energy consumption,low cooling system efficiency,and wastage of cold capacity in mines.To elucidate the seasonal variations of environmental temperature through field measurements,we selected a high-temperature working face in a deep mine as our engineering background.To enhance the heat damage control cability of the working face and minimize unnecessary cooling capac-ity loss,we introduced the multi-dimensional heat hazard prevention and control method called"Heat source barrier and cooling equipment".First,we utilize shotcrete and liquid nitrogen injection to eliminate the heat source and implemented pressure equalization ventilation to disrupt the heat transfer path,thereby creating a heat barrier.Second,we establish divi-sional prediction models for airflow temperature based on the variation patterns obtained through numerical simulation.Third,we devise the location and dynamic control strategy for the cooling equipment based on the prediction models.The results of field application show that the heat resistance and cooling linkage method comply with the safety requirement throughout the entire mining cycle while effectively reducing energy consumption.The ambient temperature is maintained below 30℃,resulting in the energy saving of 10%during the high-temperature period and over 50%during the low-temperature period.These findings serve as a valuable reference for managing heat damage in high-temperature working faces.

A Steady-State Evaluation of Simple Organic Rankine Cycle (SORC) with Low-Temperature Grade Waste Heat Source

The low-grade heat source recovery is usually constrained by the physical characteristics of the hot fluid medium. The present work focuses on the importance of energy recovery from low-temperature waste energy sources and its conversion to useful electrical power. The thermal performance analysis is based on the utilization of R-123, R-134a, R-290, R-245fa, R-1234ze-E, and R-1233zd-E fluids in a simple organic Rankine cycle (SORC). A waste energy source from an industrial sector is suggested to be available at a temperature greater than 110 °C. A hypothetical organic Rankine cycle of 10 kW nominal heat recovery was implemented to evaluate the cycle performance. It operates at evaporation and condensation temperatures of 90 °C and 45 °C, respectively. The selected vapor superheat degree at the expander entrance was 5 °C - 15 °C, and the liquid was subcooled by 5 °C at the discharge port of condenser. The estimated first law cycle thermal efficiency fell in the range of 6.4% - 7.7%. The results showed that the thermal efficiencies of R-134a, R-123, R-245fa, R-1233zd-E, and R-1234ze-E were higher than that of R-290 by 10% - 14%, 11% - 12%, 9% - 12%, 4% - 7% and 1% - 3%, respectively. R-1233zd-E, R-1234ze-E, and R-290 showed close thermal efficiency values, and it fell in the range of 6.7% - 7% for the (SORC) at a superheat degree of 15 °C. At the same superheat degree, the corresponding range of thermal efficiency for R-134a, R-123 and R-245fa fell within 7.5% - 7.7%. R-134a possessed the highest net power output of the (SORC);it reached a value of 0.91 kW as predicted at 15 °C superheat degree. Increasing the expander volumetric efficiency value by 10% improved the cycle thermal efficiency by 10% - 12%.

State-space approach to two-temperature generalized thermoelasticity without energy dissipation of medium subjected to moving heat source

In this work, a model of two-temperature generalized thermoelasticity without energy dissipation for an elastic half-space with constant elastic parameters is constructed. The Laplace transform and state-space techniques are used to obtain the general solution for any set of boundary conditions. The general solutions are applied to a specific problem of a half-space subjected to a moving heat source with a constant velocity. The inverse Laplace transforms are computed numerically, and the comparisons are shown in figures to estimate the effects of the heat source velocity and the two-temperature parameter.

Temperature field model in surface grinding: a comparative assessment

Grinding is a crucial process in machining workpieces because it plays a vital role in achieving the desired precision and surface quality.However,a significant technical challenge in grinding is the potential increase in temperature due to high specific energy,which can lead to surface thermal damage.Therefore,ensuring control over the surface integrity of workpieces during grinding becomes a critical concern.This necessitates the development of temperature field models that consider various parameters,such as workpiece materials,grinding wheels,grinding parameters,cooling methods,and media,to guide industrial production.This study thoroughly analyzes and summarizes grinding temperature field models.First,the theory of the grinding temperature field is investigated,classifying it into traditional models based on a continuous belt heat source and those based on a discrete heat source,depending on whether the heat source is uniform and continuous.Through this examination,a more accurate grinding temperature model that closely aligns with practical grinding conditions is derived.Subsequently,various grinding thermal models are summarized,including models for the heat source distribution,energy distribution proportional coefficient,and convective heat transfer coefficient.Through comprehensive research,the most widely recognized,utilized,and accurate model for each category is identified.The application of these grinding thermal models is reviewed,shedding light on the governing laws that dictate the influence of the heat source distribution,heat distribution,and convective heat transfer in the grinding arc zone on the grinding temperature field.Finally,considering the current issues in the field of grinding temperature,potential future research directions are proposed.The aim of this study is to provide theoretical guidance and technical support for predicting workpiece temperature and improving surface integrity.

MODEL OF LASER-TIG HYBRID WELDING HEAT SOURCE

The welding mechanism of laser-TIG hybrid welding process is analyzed. Withthe variation of arc current, the welding process is divided into two patterns: deep-penetrationwelding and heat conductive welding. The heat flow model of hybrid welding is presented. As todeep-penetration welding, the heat source includes a surface heat flux and a volume heat flux. Theheat source of heat conductive welding is composed of two Gaussian distribute surface heat sources.With this heat source model, a temperature field is calculated. The finite element code MARC isemployed for this purpose. The calculation results show a good agreement with the experimental data.

Discussion on heat source mechanism and geothermal system of Qinghai Gonghe-Guide Basin

The Qinghai Gonghe-Guide Basin together with the alternatively distributed mountainous region shows characteristics that the conductive geothermal resource of the basin has high geothermal gradient, the granite occurs in the bottom of borehole for geothermal exploration, and the convective hot springs in the basin-edge uplift fracture are in zonal distribution and with high-temperature geothermal water. There are still some divergences about the heat source mechanism of the basin. In this paper, queries to the view of mantle-derived heat source have been put forward, coming up with geochemical evidences to prove that the radiogenic heat of granite is the heat source within the mantle. Additionally, temperature curve is drawn based on the geothermal boring and geochemical geothermometer has been adopted for an estimation of the temperature and depth of the geothermal reservoir, it has been found that the surrounding mountains belong to the medium-temperature geothermal system while the area within the basin belongs to the high-temperature geothermal system with the temperature of borehole bottom reaching up to 175-180 ℃. In this paper, discussions on the problems existing in the calculation of geothermal gradient and the differences generated by the geothermal system have been carried out.

Diffusion Mechanism of Energy Flow in Multi-heat-source Synthesis of SiC

Through the experiments and the numerical simulation of temperature field in multi-heatsource synthesis Si C furnace, in order to research the feature point in multi-heat-source synthesis furnace, the variation law of heat fl ux was studied and the multi-directional energy fl ow diffusion mechanism was revealed. The results show that, due to the shielding action between the heat-source and the superposition effect of thermal fields, the insulating effect is best in multi-heat-source synthesis furnace. The heat emission effect is good outside the common area between heat-sources, but the heat storage is poor. Compared with the synthesis furnace that heat source is parallelly arranged, the furnace of stereoscopic arrangement has a more obvious heat stacking effect and better heat preservation effect, but the air permeability of heat source connecting regions is worse. In the case with the same ingredients, the resistance to thermal diffusion and mass diffusion is higher in heat source connecting regions.

Research on Performance of Ground-Source Heat Pump Double U Underground Pipe Heat Exchange

This paper uses FLUENT software building the three-dimensional unsteady state model of ground source heat pump single U and double U underground pipe to study on heat exchange of underground pipe system in the condition of unsteady state long-term continuous running, analyzes the change of soil temperature filed around underground pipe and performance of underground pipe heat exchange between single U and double U pipe system. The results show that double U pipe system is better than single U system, which can improve unit depth heat exchange efficiency, reduce the number of wells and reduce the initial investment.

Effect of Heat Source/Sink on Free Convective Flow of a Polar Fluid between Vertical Concentric Annuli

The purpose of this paper is to find the effect of heat source/sink parameter on free convective flow of a polar fluid in open-ended vertical concentric annuli. Exact solutions of the non-dimensional differential equations describing the flow model have been obtained one by one for two different cases of source and sink. To observe the effect of the physical parameters such as source/sink and vertex viscosity, the numerical results of the velocity and microrotational velocity are finally shown on the graphs.

INTERANNUAL VARIATIONS OF ATMOSPHERIC HEAT SOURCES AND MOISTURE SINKS OVER THE EQUATORIAL PACIFIC AND THEIR RELATIONS TO THE SST ANOMALIES

The interannual variations of atmospheric heat sources and moisture sinks over the Equatorial Pacific and their relations with the SST anomalies are studied using ECMWF reanalysis data from 1979 to 1993. It is found by singular value decomposition (SVD) analysis that the region in the tropical Pacific with high positive correlation between the vertically integrated heat source <Q1> anomaly and the SST anomaly, and between the vertically integrated moisture sink <Q2> anomaly and the SST anomaly, is mainly located in a long and narrow belt to the east of 170 °E between 5 °S and 5 °N. The analysis of the vertical structure of atmospheric heat sources and moisture sinks shows that the interannual variations of Q1, Q2 and SST in the equatorial central and eastern Pacific are strongly and positively correlated in the whole troposphere except the bottom (962.5 hPa) and the top (85 hPa) layers. However, in the western Pacific, the interannual variations of Q1 below 850 hPa is negatively related to the SST. The correlation coefficient at the level 962.5 hPa reaches even –0.59. In other layers the positive correlation between the interannual variations of Q1, Q2 and the SST are weak in the western Pacific.

Numerical simulation of gas metal arc welding temperature field

The infrared camera is used to investigate the temperature field of gas metal arc welding. The results show that the temperature distribution of weld pool and adjacent area appears cone shape. A new heat source model combined by Gaussian distribution heat source of the arc and conical distribution heat source of the droplet is set up based on the experimental results, and with the combined boundary conditions, the temperature field of gas metal arc welding is simulated using finite element method. According to the comparison between the results of experiment and simulation in temperature field shows that the new combined heat source model is more accurate and effective than the Gauss heat source model.

Modelling of the plasma-MIG welding temperature field

A three-dimensional simulation model for the plasma-MIG welding process, which takes the interaction between the plasma arc and MIG arc into account, is presented and the quasi-steady temperature fields on the workpiece are calculated with the model. The 10 mm-5A06 aluminum alloy is welded and the temperature fields are measured with the thermoelectric couple. The simulation results and measured results show that the biggest deviation of peak temperature between them is below 20 ℃, which indicates good coincidence between the simulation and measurement.

Finite element simulation of three-dimensional temperature field in underwater welding

Mathematical models of three-dimensional temperature fields in underwater welding with moving heat sources are built. Double ellipsoid Gauss model is proposed as heat sources models. Several factors which affect the temperature fields of underwater welding are analyzed. Water has little influence on thermal efftciency. Water convection coefftcient varies with the temperature difference between the water and the workpiece , and water convection makes molten pool freeze quickly. With the increase of water depth, the dimensions of heat sources model should be reduced as arc shrinks. Finite element technology is used to solve mathematical models. ANSYS software is used as finite element tool, and ANSYS Parametric Design Language is used to develop subprograms for loading the moving heat sources and the various convection coefftcients. Experiment results show that computational results by using double ellipsoid Gauss heat sources model accord well with the experimental results.

Response of Northern Hemispheric Air Temperature to Arctic Sea Ice Decline

Two numerical experiments were performed by using the Community Atmosphere Model version 3 (CAM3) with different sea ice datasets to assess the contribution of the decline of Arctic sea ice to warming in the Northern Hemisphere. One experiment was driven by observed sea ice cover data; for the other one, the authors used the sea ice data of the 4×CO2 scenario simulated by the fourth-generation European Centre Hamburg atmospheric general circulation Model of Istituto Nazionale di Geofisica e Vulcanologia, Italy (INGV_ECHAM4). The comparison of the two experiments indicates that the decline of the Arctic sea ice leads to a dramatic warming over the high latitudes of the Northern Hemisphere, characterized by a maximum warming of more than 26℃ over the Arctic region. The significant warming is closely related to the enhanced atmospheric heat source. A 40-60 Wm-2 increase in the apparent heat source was simulated in winter due to the decline of Arctic sea ice. In contrast, no significant change was found in the atmospheric apparent heat source in summer. As a result, the summer temperature change induced by the decline of Arctic sea ice appears to be weak. This study suggests that accurate sea ice cover data is crucial for future climate projection of air temperature in high latitudes.

A Study of Power Loss for 3 Phase Voltage Source Converter of Elevator

In this paper,to study the power loss of converter for elevator,The analysis is to establish relationship between parameters(current,voltages and losses in the inverter and converter) relevant for sizing of major components of the drive was done.) For high PWM(pulse width modulation) frequency like in elevator applications of fpwm =10kHz,switching losses are dominant and are about 2/3 of the total losses on IGBT switch.Transition from continuous 3 phase to discontinuous 2 phase PWM results in 50% reduction of switching loses on IGBT devices providing that PWM is not done over 60deg angle in a particular phase when current has maximum value.Total losses on IGBT(conduction + switching) are reduced approximately by ～1/3 what is still a significant reduction.Two phase PWM with reduced losses can be used for applications when acoustic noise due to increased current ripple is not significant and fall back solution to regular 3 phase PWM when drive operates under rare extreme conditions resulting in increased heat sink temperature.The analysis will be examined by further laboratory testing simulating 60% duty cycle on a dynamometer.

基于ANFIS的太阳能-空气源热泵供暖系统温度控制研究

针对太阳能-空气源热泵供暖系统运行环境复杂多变,模糊控制器的设计高度依赖人工经验的问题,提出一种基于自适应神经模糊推理系统(ANFIS)改进的模糊控制方法。该方法利用ANFIS在复杂系统建模中的优势,结合供暖系统温度响应特性和实际运行数据,建立联合供暖系统变工况ANFIS模型,生成与系统性能适配的模糊规则库并传递给模糊控制器执行。Matlab/Simulink仿真对比试验表明,与单一的模糊控制相比,该方法的控制精度提高了17.65%,调节时间缩短了36.4%,具有更高的控制精度和响应速度。

超声混粉电火花加工热力学仿真及表面形貌研究

为了研究超声振动和混粉对电火花加工的影响,基于传热理论,结合超声和混粉特性建立了超声混粉电火花传热模型。基于建立的传热模型对超声混粉电火花加工去除材料过程进行瞬态热力学仿真,并通过实验验证了仿真结果的准确性。通过仿真和实验分析了普通电火花、超声电火花、混粉电火花和超声混粉电火花四种加工方式,结果表明超声混粉电火花加工效率比普通电火花加工效率提高了23%。加入混粉和施加超声可以减少加工表面积碳,提高表面质量;可以使放电凹坑变得更加规则,使表面粗糙度降低。混粉电火花加工相对于普通电火花加工其表面粗糙度平均降低了8.9%,超声混粉电火花表面粗糙度相对于普通电火花平均降低了4.3%。