Evaluation of the use of sublevel open stoping in the mining of moderately dipping medium-thick orebodies

The flow of blasted ore during mining of moderately dipping medium-thick orebodies is a challenge.Selecting a suitable mining system for such ore bodies is difficult.This paper proposes a diamond layout sublevel open stoping system using fan blastholes with backfilling to mine such orebodies.To evaluate the performance of system the relationships between ore recovery and stope footwall dip angle,footwall surface roughness,drawpoint spacing and production blast ring burden were investigated.An ore recovery data set from 81 laboratory physical model experiments was established from combinations of the listed factors.Various modules in a back propagation neural network structure were compared,and an optimal network structure identified.An ore recovery backpropagation neural network(BPNN)forecast model was developed.Using the model and sensitivity analysis of the factors affecting the proposed open stope mining system,the significance of each factor on ore recovery was studied.The study results were applied to a case study at the Shandong Gold Group Jiaojia Gold Mine.The results showed that the application of a BPNN and sensitivity analysis models for ore recovery prediction in the proposed mining system and field experimental results confirm that the suggested mining method is feasible.

Optimization design of wide face water slots for medium-thick slab casting mold

A three-dimensional finite-element model has been established to investigate the thermal behavior of the medium-thick slab copper casting mold with different cooling water slot designs. The mold wall temperatures measured using thermocouples buried in different positions of the mold with the original designed cooling system were analyzed to determine the corresponding heat flux profile. This profile was then used for simulation to predict the temperature distribution and the thermal stress distribution of the molds. The predicted temperatures during operation matched the plant measurements. The results showed that the maximum temperature, about 635 K in the wide hot surface, was found about 60 mm below the meniscus and 226 mm from the center of the mold. For the mold with the type I modified design, there was an insignificant decrease in temperature of about 5 K, and for the mold with the type II modified design, the maximum temperature was decreased by about 15 K and the temperature of the hot surface was distributed more uniformly along the length of the mold. The corresponding maximum thermal stress at the hot surface of the mold was reduced from 408 MPa to 386 MPa with the type II modified design. The results indicated that the modified design II is beneficial to the increase of mold life and the quality of casting slabs.

Magnetic Method Surveying and Its Application for the Concealed Ore-Bodies Prospecting of Laba Porphyry Molybdenum Ore Field in Shangri-La, Northwestern Yunnan Province, China

Recently, a number of large molybdenum (-copper) deposits have been discovered successively in the Laba area, Shangri-La county, northwestern Yunnan province. The investigation confirmed that there is a superlarge porphyry-skarn hydrothermal vein type molybdenum-polymetallic- metallogenic system with the total prediction reservoir of more than 150 mt molybdenum. The porphyry intrusions contributed to the mineralization closely, the superficial little vein molybdenum (-copper, lead, silver) ore-bodies are usually located in faults and fractures, and the deep porphyry type ore-bodies occurred in the granodiorite porphyries, the skarn type ore-bodies occurred in the contact zone intrused into Triassic limestone or Permian basalts. Laba ore block is a new exploration area with great prospecting potential. In order to reduce the target area and guide the further exploration work, the magnetic method measurement about 3.3 square kilometres was carried out in the ore field. This paper presents an application of analyzing the horizontal and vertical derivative, using Fast Fourier Transform (FFT) filter (FFT high-pass, low-pass, cosine roll-off, suscepbility), calculated spectra frequency energy to predict the depth and intensity of the apparent remanence magnetization of source (Hilbert). The calculated results and magnetic anomalous show that the remanence anomaly is caused by the intrusions into the Triassic limestone and Permian basalts with small anomalies, and the depth of located source is not great. We have identified a number of positions to the three drilled well, the drilled result specify interpretation with very high accuracy. The magnetic method is helpful to identify porphyry mineralization, and judge the shape and depth of the concealed ore-bearing intrusive bodies under the similar geological condition.

Application of Audio-Magnetotelluric Method for Exploration the Concealed Ore-Bodies in Yuele Lead-Zinc Ore Feild, Daguan County, NE Yunnan Province, China

The results of recent mineral exploration in the Yuele lead-zinc mining area of Daguan County, northeastern Yunnan province, showed that there are much early Paleozoic strata under thick late Paleozoic strata in northeastern Yunnan province, where developed some hidden salt structures (SSs), often with lead-zinc polymetallic mineralization varying degrees along the tension torsional fault (belts) or fracture (joint). The ore-bodies belong to the epigenetic hydrothermal filling vein-type deposit, and the prospecting potential is great. In this area, the superficial mineralization information displayed clear, but the deep mineralization is unknown, so the exploration work is restricted. The audio-megnetotelluric (AMT) surveying is an advantageous method to characterize the size, resistivity and skin depth of the polarizable mineral deposit concealed beneath thick overburden. This paper presents the surveying results using AMT method to evaluate the concealed lead-zinc mineralization in Yuele lead-zinc ore field, Daguancounty, NE Yunnan province, China. After comparing the interpretation result of AMT surveying data with the geological data and the drilling data, it is found that there is some distinct difference in resistivity and polarizable between ore-bodies hosted strata, upper strata and gypsum strata. The results show that AMT method is helpful to identify lead-zinc mineralization under this geological condition.

Study on determining of reinforced concrete false roof strength and design of reinforcement based on reliability theory

Study on efficient mining of the steep incline and fractured ore-bodies in Yongshaba mine of Guizhou Kailin Group shows that ore-body is fractured and difficult to support the roadways in-vein.After research of the actual conditions about the ore-bodies,we have made the initial decision to adopt reconstruction of roof downward sublevel cut-and-fill mining.The men work safely under the false roof supporting the top plate.However,the difficult problem is how to determine the strength of the false roof.In this case,the method based on reliability theory has been put forward.Combined with elastic mechanics and field practice,when practical value of reliable probability is 90 %,the value of the false roof strength has been calculated,and the study shows that stope span greatly influences the false roof strength.With the strength of artificial roof,the reasonable reinforcement design ensures the false roof which can supply the demand of strength under large span and load.

Microstructure and Mechanical Properties of Dissimilar Double-Side Friction Stir Welds Between Medium-Thick 6061-T6 Aluminum and Pure Copper Plates

It is difficult to achieve Al/Cu dissimilar welds with good mechanical properties for medium-thick plates due to the inherent high heat generation rate at the shoulder-workpiece contact interface in conventional friction stir welding.Thus,doubleside friction stir welding is innovatively applied to join 12-mm medium-thick 6061-T6 aluminum alloy and pure copper dissimilar plates,and the effect of welding speeds on the joint microstructure and mechanical properties of Al/Cu welds is systematically analyzed.It reveals that a sound Al/Cu joint without macroscopic defects can be achieved when the welding speed is lower than 180 mm/min,while a nonuniform relatively thick intermetallic compound(IMC)layer is formed at the Al/Cu interface,resulting in lots of local microcracks within the first-pass weld under the plunging force of the tool during friction stir welding of the second-pass,and seriously deteriorates the mechanical properties of the joint.With the increase of welding speed to more than 300 mm/min void defects appear in the joint,but the joint properties are still better than the welds performed at low welding speed conditions since a continuous uniform thin IMCs layer is formed at the Al/Cu interface.The maximum tensile strength and elongation of Al/Cu weld are,respectively,135.11 MPa and 6.06%,which is achieved at the welding speed of 400 mm/min.In addition,due to the influence of welding distortion of the first-pass weld,the secondpass weld is more prone to form void defects than the first-pass weld when the same plunge depth is applied on both sides.The double-side friction stir welding is proved to be a good method for dissimilar welding of medium-thick Al/Cu plates.