Because the bonding interface of dissimilar metal joint between AZ31 B Mg alloy and DP600 galvanized steel by keyholeless friction stir spot welding(KFSSW)is permanent bonding,the interface morphology cannot be direct...Because the bonding interface of dissimilar metal joint between AZ31 B Mg alloy and DP600 galvanized steel by keyholeless friction stir spot welding(KFSSW)is permanent bonding,the interface morphology cannot be directly observed.If the joint is separated by external force,the original features of bonding interface of joint will be destroyed,which has influence on the accuracy for observation and analysis of the result.In this paper,the coordinates of the key point at the interface of every cross-section at intervals of 0.2 mm were measured and connected into an outline.The outline of all interfaces makes up the three-dimensional morphologies of bonding interface between AZ31 B Mg alloy and DP600 steel by KFSSW,which was constructed by Solidworks software to restore the real mechanical bonding state of joint.Combined with the microhardness analysis of cross-section and results of in-situ tensile test,the unique bonding state and morphology of Mg and steel in the welded joint were confirmed.展开更多
The effects of rare earths(RE)-Mg-Ti compound modification on the structures and properties of high-carbon high speed steel(HSS) were researched.The impact toughness(α_k),the fracture toughness(K_(1c))and threshold o...The effects of rare earths(RE)-Mg-Ti compound modification on the structures and properties of high-carbon high speed steel(HSS) were researched.The impact toughness(α_k),the fracture toughness(K_(1c))and threshold of fatigue crack growth(ΔK_(th))are tested.The thermal fatigue test is done on a self-straining thermal fatigue tester,the wear test is done on a high temperature wear test machine.The results show that the matrix can be refined by the RE-Mg-Ti compound modification,the eutectic carbides are inclined to spheroidicize and are distributed evenly,the morphology and distribution of eutectic carbides are improved by appropriate RE-Mg-Ti complex modification.After RE-Mg-Ti compound modification,a little effects can be found on the strength,hardness and red hardness,but the fracture toughness(K_(1c)) and threshold of fatigue crack growth(△K_(th)) are improved in the meantime,the impact toughness (α_k) is increased by over one time,and the resistance to thermal fatigue and wear resistance at an elevated temperature are remarkably improved.展开更多
以不同脱氧方式熔炼的海洋工程用钢为研究对象,利用SEM、EDS及Image-Pro Plus 6.0软件对钢中夹杂物形貌、组成及尺寸分布等进行表征,通过3.5%NaCl溶液中阳极极化及腐蚀实验对钢中夹杂物诱发点蚀的行为进行探究。结果表明,与Al-Mg脱氧钢...以不同脱氧方式熔炼的海洋工程用钢为研究对象,利用SEM、EDS及Image-Pro Plus 6.0软件对钢中夹杂物形貌、组成及尺寸分布等进行表征,通过3.5%NaCl溶液中阳极极化及腐蚀实验对钢中夹杂物诱发点蚀的行为进行探究。结果表明,与Al-Mg脱氧钢相比,Ti-Mg脱氧钢中形成了含有TiO_x的复合氧化物,夹杂数量更多且平均尺寸更小(小于1μm),有利于MnS的异质形核析出及弥散分布;低腐蚀活性的含TiOx复合氧化物及高度分散、异质局部析出MnS夹杂具有较低的点蚀敏感性及自腐蚀催化作用,降低了点蚀的诱发及扩展,有效提高了钢的抗点蚀性能。展开更多
基金supported by Natural Science Foundation of Shandong Province(No.ZR2019PEE042)。
文摘Because the bonding interface of dissimilar metal joint between AZ31 B Mg alloy and DP600 galvanized steel by keyholeless friction stir spot welding(KFSSW)is permanent bonding,the interface morphology cannot be directly observed.If the joint is separated by external force,the original features of bonding interface of joint will be destroyed,which has influence on the accuracy for observation and analysis of the result.In this paper,the coordinates of the key point at the interface of every cross-section at intervals of 0.2 mm were measured and connected into an outline.The outline of all interfaces makes up the three-dimensional morphologies of bonding interface between AZ31 B Mg alloy and DP600 steel by KFSSW,which was constructed by Solidworks software to restore the real mechanical bonding state of joint.Combined with the microhardness analysis of cross-section and results of in-situ tensile test,the unique bonding state and morphology of Mg and steel in the welded joint were confirmed.
文摘The effects of rare earths(RE)-Mg-Ti compound modification on the structures and properties of high-carbon high speed steel(HSS) were researched.The impact toughness(α_k),the fracture toughness(K_(1c))and threshold of fatigue crack growth(ΔK_(th))are tested.The thermal fatigue test is done on a self-straining thermal fatigue tester,the wear test is done on a high temperature wear test machine.The results show that the matrix can be refined by the RE-Mg-Ti compound modification,the eutectic carbides are inclined to spheroidicize and are distributed evenly,the morphology and distribution of eutectic carbides are improved by appropriate RE-Mg-Ti complex modification.After RE-Mg-Ti compound modification,a little effects can be found on the strength,hardness and red hardness,but the fracture toughness(K_(1c)) and threshold of fatigue crack growth(△K_(th)) are improved in the meantime,the impact toughness (α_k) is increased by over one time,and the resistance to thermal fatigue and wear resistance at an elevated temperature are remarkably improved.
文摘以不同脱氧方式熔炼的海洋工程用钢为研究对象,利用SEM、EDS及Image-Pro Plus 6.0软件对钢中夹杂物形貌、组成及尺寸分布等进行表征,通过3.5%NaCl溶液中阳极极化及腐蚀实验对钢中夹杂物诱发点蚀的行为进行探究。结果表明,与Al-Mg脱氧钢相比,Ti-Mg脱氧钢中形成了含有TiO_x的复合氧化物,夹杂数量更多且平均尺寸更小(小于1μm),有利于MnS的异质形核析出及弥散分布;低腐蚀活性的含TiOx复合氧化物及高度分散、异质局部析出MnS夹杂具有较低的点蚀敏感性及自腐蚀催化作用,降低了点蚀的诱发及扩展,有效提高了钢的抗点蚀性能。
