Mg-10Y-1.5Sm合金的组织和力学性能

采用合金熔炼、组织分析和拉伸试验,研究了Mg-10Y-1.5Sm合金经过固溶时效后的组织和力学性能。结果表明,合金的组织由α-Mg基体和Mg24Y5相组成,细小的Mg24Y5颗粒相均匀弥散地分布在α-Mg基体上;Sm加入后没有形成新相,而是通过固溶作用,进一步强化了α-Mg基体和Mg24Y5相;合金在200～300℃之间的抗拉强度均大于200 MPa,伸长率均为3%左右,与室温时相比没有发生显著变化;合金的力学性能优于Mg-10Y合金,最高使用温度可达350℃。

Microstructure and mechanical property of a high-strength Mg-10Gd-6Y-1.5Zn-0.5Zr alloy prepared by multi-pass equal channel angular pressing

In this work,a high-strength Mg–10Gd–6Y–1.5Zn–0.5Zr(wt.%)alloy was fabricated by successive multi-pass equal channel angular pressing(ECAP).The microstructure and mechanical property of as-cast and ECAP alloys were systematically researched by X-ray diffractometer,scanning electron microscopy,transmission electron microscopy and compression test.The results show that the microstructure of as-cast alloy consists ofα-Mg grains,Mg24Y5 networks,18R blocks,fine 14H lamellas,and fewY-rich particles.After 8 passes ECAP,dynamic recrystallization ofα-Mg is developed and their average grain size decreases to about 1μm.The network Mg_(24)Y_(5) phase at grain boundaries is broken into small particles with average diameter lower than 0.5μm.Moreover,18R blocks are kinked and delaminated,or broken into small particles and blended with Mg24Y5 particles.14H lamellas grow gradually or are dynamically precipitated within certainα-Mg grains.Compression tests indicate that 8p ECAP alloy exhibits excellent mechanical property with compressive strength of 537 MPa and fracture strain of 17.0%.The significant improvement for both strength and ductility of deformed alloy could be ascribed to DRX grains,refined Mg24Y5 particles,18R kinking and dynamical precipitation of 14H.

Effect of heat treatment on microstructures and mechanical properties of sand-cast Mg-10Gd-3Y-0.5Zr magnesium alloy

The microstructure, mechanical properties and fracture behavior of sand-cast Mg-10Gd-3Y-0.5Zr alloy （mass fraction,%） under T6 condition （air cooling after solid solution and then aging heat treatment） were investigated. The optimum T6 heat treatments for sand-cast Mg-10Gd-3Y-0.5Zr alloy are （525 ℃, 12 h＋225 ℃, 14 h） and （525 ℃, 12 h＋250 ℃, 12 h） according to age hardening curve and mechanical properties, respectively. The ultimate tensile strength, yield strength and elongation of the Mg-10Gd-3Y-0.5Zr alloy treated by the two optimum T6 processes are 339.9 MPa, 251.6 MPa, 1.5%and 359.6 MPa, 247.3 MPa, 2.7%, respectively. The tensile fracture mode of peak-aged Mg-10Gd-3Y-0.5Zr alloy is transgranular quasi-cleavage fracture.

Effect of ageing time on corrosion behavior of Mg-10Gd-4.8Y-0.6Zr extruded-alloy

The corrosion behaviors of Mg-10Gd-4.8Y-0.6Zr extruded-alloys with various ageing time were investigated by immersion test and electrochemical measurements.The results show that the corrosion rate of the experimental alloy decreases with the increase of ageing time from 0 to 108 h.The corrosion resistance of the experimental alloy was found to increase with the increase of the size of the precipitate phases.The open circuit potential of the experimental alloy increases with the increase of the ageing time.The potentiodynamic polarization curves show that the cathodic over-potential increases with the increase of ageing time,leading to a decrease in the current density of anodic current plateau with the increase of ageing time.

Low temperature mechanical properties of as-extruded Mg-10Gd-3Y-0.5Zr magnesium alloy

Influence of multi-cycle cryogenic treatment and tensile temperature on microstructure, mechanical properties and fracture mechanism of as-extruded Mg-10Gd-3Y-0.5Zr magnesium alloy was investigated. The results show that there have no significant changes in tensile properties of the tested alloy after 10 d in liquid nitrogen immersion or 10 cycles of high-low temperature treatment at all test temperatures. The room temperature ultimate tensile strength increases from 398 MPa to 417 MPa after 20 cycles of high-low temperature treatments. Compared with the room temperature, the tested alloys exhibit higher tensile properties at low temperatures. At -196 °C, the yield strength and ultimate tensile strength of the as-extruded-T5 Mg-10Gd-3Y-0.5Zr alloy are 349 MPa and 506 MPa, respectively, increasing by about 18% and 27%, respectively. The transgranular cleavage fracture mechanism is observed at room temperature, while at low temperatures both ductile fracture and cleavage fracture behaviors coexist.

Effects of Sm addition on microstructure and mechanical properties of a Mg-10Y alloy

To further increase the mechanical properties, 0.5wt.% Sm was introduced to a Mg-10Y alloy in this study. The effects of Sm addition on the microstructures and mechanical properties of the Mg-10Y alloy, especially the aged Mg-10Y alloy, were investigated. The microstructure observation and tensile tests were performed by using an optical microscopy, a scanning electron microscopy and a universal material testing machine, respectively. The phase analysis was performed using X-ray diffractometer. The results show that the 0.5wt.% Sm addition can not only promote the formation of fine and dispersed Mg24Y5 phases, but also improve their morphology and distribution; it also increases the thermal stability of Mg24Y5 phases. Sm addition is seen to increase the ultimate tensile strength of Mg-10Y alloy at elevated temperatures(200, 250, 300 and 350 ℃), while decrease the elongation. But the elongation is still up to 7.5% even at 350 ℃. In the range of 250 ℃ to 300℃, the ultimate tensile strength of the alloy reaches its maximum(with a range average of 235 MPa) and is not sensitive to the temperature change, which is very useful to the application of heat-resistant magnesium alloys. Even at 350 ℃, the ultimate tensile strength of Mg-10Y-0.5Sm is still up to 155 MPa. Considering both of the ultimate tensile strength and elongation, the maximum application temperature of the Mg-10Y-0.5Sm alloy can be up to 300 ℃. The strengthening mechanisms of Mg-10Y-0.5Sm alloy are mainly attributed to dispersion strengthening of Mg24Y5 phase particles with a certain solubility of Sm and grain refinement strengthening of α-Mg matrix.

Effect of different casting methods on microstructure and mechanical properties of Mg-10Gd-3Y-0.6Zr alloy

The effects of two different casting methods on the microstructures and mechanical properties of as-cast and T6-cast states of Mg-10Gd-3Y-0.6Zr alloy were studied by using metal mold casting and squeeze casting.The results show that the microstructure of Mg-10Gd-3Y-0.6Zr alloy is mainly composed ofα-Mg primary phase and Mg 24(Gd,Y)5 eutectic phase.The squeeze cast grains are small with a dendrite like morphology,and the tensile strength of the alloy in T6 state can reach 285 MPa.While the metal grains are coarse,the eutectic phases are distributed in the grain boundary,and the tensile strength of the alloy in T6 state is only 250 MPa.