Effects of stress loading mode on microstructures and properties of Mg-9Gd-2Nd-0.5Zr alloy treated by creep aging

Creep aging forming(CAF) is a potential process used to manufacture large integral components of magnesium(Mg) alloys. The selected stress plays a crucial role in creep aging processes but the mechanism by which stress loading method affects creep aging of Mg alloys is still unclear. In this paper, the microstructural evolution of precipitated phases and precipitation-free zones(PFZ) at grain boundaries with different stress loading modes(unstressed, unidirectional tensile stress, and cyclic stress) at 250 ℃ were investigated along with changes in mechanical properties. The results showed that the addition of stress during aging effectively promoted the precipitation of precipitated phases, while unaffecting grain size. Unidirectional tensile stress caused directional growth of β phase([1010]), as well as rotation of weave towards the basal plane texture, resulting in namely stress orientation effect. Solute atoms diffused in the direction of tensile stress while vacancies moved perpendicular to the direction of tensile stress, resulting in PFZ at grain boundaries(157.06 nm). By contrast, cyclic stresses led to the growth of β phase in three directions([1010], [1100] and [0110]). The solute atoms and vacancies were uniformly distributed in the Mg matrix instead of directional diffusion, effectively reducing the width of PFZ(112.39 nm) at the grain boundary. These features significantly improved the mechanical properties of alloy specimens after cyclic stress creep aging when compared to unidirectional stress creep aging, with yield strength(YS), ultimate tensile strength(UTS), and elongation(EL) enhanced from 171.6 MPa, 305.5 MPa, and 4.4%to 174.8 MPa, 326.3 MPa, and 6.9%, respectively.

Grain refinement impact on the mechanical properties and wear behavior of Mg-9Gd-3Y-2Zn-0.5Zr alloy after decreasing temperature reciprocating upsetting-extrusion

Based on the deforming technique of severe plastic deformation(SPD), the grain refinement of a Mg-9Gd-3Y-2Zn-0.5Zr alloy treated with decreasing temperature reciprocating upsetting-extrusion(RUE) and its influence on the mechanical properties and wear behavior of the alloy were studied. The RUE process was carried out for 4 passes in total, starting at 0 ℃ and decreasing by 10 ℃ for each pass. The results showed that as the number of RUE passes increased, the grain refinement effect was obvious, and the second phase in the alloy was evenly distributed. Room temperature tensile properties of the alloy and the deepening of the RUE degree showed a positive correlation trend, which was due to the grain refinement, uniform distribution of the second phase and texture weakening. And the microhardness of the alloy showed that the microhardness of RUE is the largest in 2 passes. The change in microhardness was the result of dynamic competition between the softening effect of DRX and the work hardening effect. In addition, the wear resistance of the alloy showed a positive correlation with the degree of RUE under low load conditions. When the applied load was higher, the wear resistance of the alloy treated with RUE decreased compared to the initial state alloy. This phenomenon was mainly due to the presence of oxidative wear on the surface of the alloy, which could balance the positive contribution of severe plastic deformation to wear resistance to a certain extent.

Friction and wear behavior of Mg–11Y–5Gd–2Zn–0.5Zr(wt%)alloy with oil lubricant

The sliding friction and wear behaviors of Mg-11Y-5Gd-2Zn-0.5Zr （wt%） alloy were investigated under oil lubricant condition by pin-on-disk configuration with a constant sliding distance of 1,000 m in the temperature range of 25-200℃. Results indicate that the volumetric wear rates and average friction coefficients decrease with the increase of sliding speeds, and increase with the increase of test temperature below 150℃. The hard and thermally stable Mg12（Y,Gd）Zn phase with long-period stacking order structure in the alloy presents significant wear resistance, The wear mechanism below 100℃ is abrasive wear as a result of plastic extrusion deformation. The corporate effects of severe abrasive, oxidative, and delaminating wear result in the tribological mechanism above 100℃.

(Y,Gd)H_(2) phase formation in as-cast Mg-6Gd-3Y-0.5Zr alloy

In this work,a new(Y,Gd)H_(2) precipitate was identified and systematically investigated in the as-cast Mg-6Gd-3Y-0.5Zr alloy by XRD,SEM with EDS,TEM with EDS techniques and thermodynamics analysis.Results show that the as-cast alloy contains α-Mg,Mg_(24)(Gd,Y)_(5),and(Y,Gd)H_(2) phase.The(Y,Gd)H_(2) phase usually forms near the eutectic phase Mg_(24)(Gd,Y)_(5) or in the α-Mg grains,displaying a rectangle-shape.The Mg_(24)(Gd,Y)_(5) and(Y,Gd)H_(2) phases crystalize in bcc and fcc structure,respectively,and the(Y,Gd)H_(2) phase has a semi-coherent relationship with α-Mg matrix.The thermodynamics calculation results reveal that the hydrogen dissolved in the melt leads to the formation of hydrides.It is also found that the(Y,Gd)H_(2) hydride can form directly from the liquid phase during solidification.Additionally,it can precipitate by the decomposition of Mg_(24)(Gd,Y)_(5) phase due to absorbing hydrogen from the remaining melt.

固溶处理对Mg-Dy-Zn合金显微组织和腐蚀性能的影响

采用光学显微镜(OM)、扫描电镜(SEM)、X-射线衍射仪(XRD)、显微硬度计及电化学工作站等设备,研究了固溶处理对Mg-2Dy-0.5Zn(at%)合金显微组织及腐蚀性能的影响。结果表明,铸态合金的显微组织由α-Mg枝晶和分布在枝晶间的析出相组成,其中析出相由片层状Mg12Zn Dy相、蜂窝状Mg8Zn Dy相和少量立方体颗粒状Mg24Dy5相组成。随着固溶温度(500~540℃)和固溶时间(0~12 h)的增加,合金的析出相逐渐溶解,同时有少量颗粒状的(Mg,Zn)xDy相沿晶界析出。合金在530℃固溶8 h,析出相几乎完全固溶到α-Mg基体中,合金基体的显微硬度增加,其值达到74.74 HV0.1。此外,电化学测试结果表明,固溶态(530℃固溶8 h)合金显示出优异的耐蚀性能,其腐蚀电流和腐蚀电位分别为8.650×10-4A和-1.159 V。该优异的耐蚀性主要来自于合金元素的均匀分布,低的析出相体积分数和细小的晶粒尺寸。

Incorporation of Mg-phenolic networks as a protective coating for magnesium alloy to enhance corrosion resistance and osteogenesis in vivo

Magnesium(Mg) and its alloys have been intensively studied to develop the next generation of bone implants recently, but their clinical application is restricted by rapid degradation and unsatisfied osteogenic effect in vivo. A bioactive chemical conversion Mg-phenolic networks complex coating(e EGCG) was stepwise incorporated by epigallocatechin-3-gallate(EGCG) and exogenous Mg^(2+)on Mg-2Zn magnesium alloy. Simplex EGCG induced chemical conversion coating(c EGCG) was set as compare group. The in vitro corrosion behavior of Mg-2Zn alloy, c EGCG and e EGCG was evaluated in SBF using electrochemical(PDP, EIS) and immersion test. The cytocompatibility was investigated with rat bone marrow mesenchymal stem cells(r BMSCs). Furthermore, the in vivo tests using a rabbit model involved micro computed tomography(Micro-CT) analysis, histological observation, and interface analysis. The results showed that the e EGCG is Mgphenolic multilayer coating incorporated Mg-phenolic networks, which is rougher, more compact and much thicker than c EGCG. The e EGCG highly improved the corrosion resistance of Mg-2Zn alloy, combined with its lower average hemolytic ratios, continuous high scavenging effect ability and relatively moderate contact angle features, resulting in a stable and suitable biological environment, obviously promoted r BMSCs adhesion and proliferation. More importantly, Micro-CT, histological and interface elements distribution evaluations all revealed that the e EGCG effectively inhibited degradation and enhanced bone tissue formation of Mg alloy implants. This study puts forward a promising bioactive chemical conversion coating with Mg-phenolic networks for the application of biodegradable orthopedic implants.

Microstructure and Corrosion Behavior of the As-Extruded Mg-4Zn-2Gd-0.5Ca Alloy

In order to study the corrosion resistance of extruded magnesium alloys,the Mg-4Zn-2Gd-0.5Ca alloy was extruded at the speed of 0.01-0.1 mm/s with the temperature of 280-360℃in present study.Hot extrusion results show that the volume fraction of precipitates(Vpre),VDRX(the dynamic recrystallization rate) and the average size of DRXed grain(dDRX) decrease with the decrease in extrusion speed,and the corrosion rate of the alloy also shows a downward trend.On the contrary,the values of Vpre,VDRX and dDRX increase with the increase in extrusion temperature,and the corrosion resistance of Mg-4Zn-2Gd-0.5Ca alloy decreases.When the extrusion speed is 0.01 mm/s and the extrusion temperature is 280℃,the alloy has the best corrosion resistance.The corrosion of extruded Mg-4Zn-2Gd-0.5Ca alloy occurs preferentially on the magnesium matrix around W and I phases in the DRXed zone.With the further corrosion,the corrosion continues to spread along the phase,and the corrosion area gradually increases.Galvanic corrosion plays a leading role in the corrosion process.Moreover,there are a large number of basal plane textures in the unDRXed region,which is conducive to improving the corrosion resistance of magnesium alloys.In addition,the decrease in grain size also makes the corrosion of magnesium alloy more uniform.