Microstructure and mechanical properties of Mg-3.0Nd-0.4Zn-0.4Zr magnesium alloy

Mg-3.0Nd-0.4Zn-0.4Zr magnesium alloy were prepared by cast-extruding and chip-extruding.Microstructure,tensile and creep properties of the alloy were investigated.The results show that the alloy exhibit particle dynamic recrystallization during extrusion.The cast extruded-T6 rods at room temperature have a highest tensile strength of 258.5 MPa and a highest yield strength of 135.7 MPa.With the increase of test temperature,the strength of the alloy declines and the elongation increases.At 473 K,creep strain in the primary creep stage increases with increasing the creep stresses.Under 110 MPa,time spent during primary creep decreases with increasing the test temperatures.Stress exponent and creep activation energy of the alloy are 4.4 and 104 kJ/mol,respectively.Creep of the alloy can be controlled by dislocation climb mechanism.The morphology of the fracture surfaces was examined by employing scanning electron microscope.

Grain refinement impact on the mechanical properties and wear behavior of Mg-9Gd-3Y-2Zn-0.5Zr alloy after decreasing temperature reciprocating upsetting-extrusion

Based on the deforming technique of severe plastic deformation(SPD), the grain refinement of a Mg-9Gd-3Y-2Zn-0.5Zr alloy treated with decreasing temperature reciprocating upsetting-extrusion(RUE) and its influence on the mechanical properties and wear behavior of the alloy were studied. The RUE process was carried out for 4 passes in total, starting at 0 ℃ and decreasing by 10 ℃ for each pass. The results showed that as the number of RUE passes increased, the grain refinement effect was obvious, and the second phase in the alloy was evenly distributed. Room temperature tensile properties of the alloy and the deepening of the RUE degree showed a positive correlation trend, which was due to the grain refinement, uniform distribution of the second phase and texture weakening. And the microhardness of the alloy showed that the microhardness of RUE is the largest in 2 passes. The change in microhardness was the result of dynamic competition between the softening effect of DRX and the work hardening effect. In addition, the wear resistance of the alloy showed a positive correlation with the degree of RUE under low load conditions. When the applied load was higher, the wear resistance of the alloy treated with RUE decreased compared to the initial state alloy. This phenomenon was mainly due to the presence of oxidative wear on the surface of the alloy, which could balance the positive contribution of severe plastic deformation to wear resistance to a certain extent.

Deformation mechanism of fine grained Mg-7Gd-5Y-l.2Nd-0.5Zr alloy under high temperature and high strain rates

Fine grained Mg-7Gd-5Y-1.2Nd-0.5Zr alloy was investigated by dynamic compression tests using a Split Hopkinson Pressure Bar under the strain rates in the range 1000-2000 s^(-1) and the temperature range 293-573 K along the normal direction.The microstructure was measured by optical microscopy,electron back-scattering diffraction,transmission electron microscopy and X-ray diffractometry.The results showed that Mg-7Gd-5Y-1.2Nd-0.5Zr alloy had the positive strain rate strengthening effect and thermal softening effect at high temperature.The solid solution of Gd and Y atoms in Mg-7Gd-5Y-1.2Nd-0.5Zr alloy reduced the asymmetry of α-Mg crystals and changed the critical shear stress of various deformation mechanisms.The main deformation mechanisms were prismatic slip and pyramidal(a)slip,{102}tension twinning,and dynamic recrystallization caused by local deformation such as particle-stimulated nucleation.c 2020 Published by Elsevier B.V.on behalf of Chongqing University.

Friction and wear behavior of Mg–11Y–5Gd–2Zn–0.5Zr(wt%)alloy with oil lubricant

The sliding friction and wear behaviors of Mg-11Y-5Gd-2Zn-0.5Zr （wt%） alloy were investigated under oil lubricant condition by pin-on-disk configuration with a constant sliding distance of 1,000 m in the temperature range of 25-200℃. Results indicate that the volumetric wear rates and average friction coefficients decrease with the increase of sliding speeds, and increase with the increase of test temperature below 150℃. The hard and thermally stable Mg12（Y,Gd）Zn phase with long-period stacking order structure in the alloy presents significant wear resistance, The wear mechanism below 100℃ is abrasive wear as a result of plastic extrusion deformation. The corporate effects of severe abrasive, oxidative, and delaminating wear result in the tribological mechanism above 100℃.