Mg-3.0Nd-0.4Zn-0.4Zr magnesium alloy were prepared by cast-extruding and chip-extruding.Microstructure,tensile and creep properties of the alloy were investigated.The results show that the alloy exhibit particle dynam...Mg-3.0Nd-0.4Zn-0.4Zr magnesium alloy were prepared by cast-extruding and chip-extruding.Microstructure,tensile and creep properties of the alloy were investigated.The results show that the alloy exhibit particle dynamic recrystallization during extrusion.The cast extruded-T6 rods at room temperature have a highest tensile strength of 258.5 MPa and a highest yield strength of 135.7 MPa.With the increase of test temperature,the strength of the alloy declines and the elongation increases.At 473 K,creep strain in the primary creep stage increases with increasing the creep stresses.Under 110 MPa,time spent during primary creep decreases with increasing the test temperatures.Stress exponent and creep activation energy of the alloy are 4.4 and 104 kJ/mol,respectively.Creep of the alloy can be controlled by dislocation climb mechanism.The morphology of the fracture surfaces was examined by employing scanning electron microscope.展开更多
A new rare earth magnesium alloy(Mg-6 Zn-4 Sm-0.4 Zr, wt.%) was prepared by permanent mould casting. The microstructure and mechanical properties of the alloy sample in as-cast and various heat treatment situations we...A new rare earth magnesium alloy(Mg-6 Zn-4 Sm-0.4 Zr, wt.%) was prepared by permanent mould casting. The microstructure and mechanical properties of the alloy sample in as-cast and various heat treatment situations were characterized with an optical microscope(OM), X-ray diffractometer(XRD), scanning electron microscope(SEM) equipped with energy dispersive spectroscope(EDS), transmission electron microscope(TEM) and mechanical tests at room temperature, respectively. The experimental results show that the as-cast alloy mainly consists of α-Mg, eutectic Mg_2Zn_3, MgZnSm and Mg_(41)Sm_5. These eutectic phases with continuous or semicontinuous morphology principally distribute along grain boundaries. Almost all the eutectic compounds dissolve in α-Mg and the grains have no obvious growth trend after optimum solution treatment at 490 °C for 18 h. Meanwhile, the ultimate tensile strength(UTS) of 229 MPa and elongation(EL) to rupture of 9.78% can be achieved through the optimal solution treatment, which increase by 37 MPa and 57.74%, respectively, compared with that of the as-cast alloy. Further aging treatments at 200 °C for different durations lead to the conspicuous increment of mechanical properties and prominent age-hardening response. Peak-aged alloy(treated at 200 °C for 12 h) reveals better mechanical properties(UTS 258 MPa, EL 9.42%, hardness 73.4 HV) compared with the same alloy treated in other aging conditions, which is mainly ascribed to precipitated Mg_2Zn_3 and MgZn_2 phases. Fracture analysis demonstrates that the as-cast alloy belongs to inter-granular and cleavage fracture patterns, while the solutionized alloy(treated at 490 °C for 18 h) reveals trans-granular and quasi-cleavage fracture modes. For the peak-aged alloy, the fracture pattern obeys the mixture of trans-granular and cleavage modes.展开更多
A Mg-6Zn-3Gd(mass fraction,%) alloy,noted as ZG63,was coated by different micro-arc oxidation(MAO) processes,and the coating structure and corrosion resistance of the alloy were studied using scanning electron microsc...A Mg-6Zn-3Gd(mass fraction,%) alloy,noted as ZG63,was coated by different micro-arc oxidation(MAO) processes,and the coating structure and corrosion resistance of the alloy were studied using scanning electron microscopy(SEM),glancing angle X-ray diffractometry(GAXRD) and various electrochemical methods.The micro-arc oxidation process consists of three stages and corresponds with different coating structures.In the initial stage,the coating thickness is linearly increased and is controlled by electrochemical polarization.In the second stage,the coating grows mainly inward and accords with parabolic regularity.In the third stage,the loose coating forms and is controlled by local arc light.The looser coating is mainly composed of MgSiO3 and the compact coating is mainly composed of MgO.From micro-arc oxidation stage to local arc light stage,the corrosion resistance of the coated alloy firstly increases and then decreases.The satisfied corrosion resistance corresponds to the coating time ranging from 6 to10 min.展开更多
Microstructure and mechanical behavior of the squeeze-casting and squeeze-casting plus T6 heat-treated Mg-8 Gd-2 Y-0.4 Zr magnesium alloys at room and elevated temperatures were investigated. The experimental results ...Microstructure and mechanical behavior of the squeeze-casting and squeeze-casting plus T6 heat-treated Mg-8 Gd-2 Y-0.4 Zr magnesium alloys at room and elevated temperatures were investigated. The experimental results showed that the T6 treated alloy aged at slightly high temperature exhibited good comprehensive strength and ductility. However, the strength of the tested alloys was not sensitive to the change of tensile temperature, i e, the yield strength and ultimate tensile strength did not decrease significantly with increasing tensile temperature, while the ductility increased greatly. In addition, the squeeze-casting alloy exhibited predominant intergranular fracture accompanied by minor transgranular rupture, and the tensile fracture mode for the T6 treated alloy had typical transgranular cleavage fracture.展开更多
Hot compression tests of Mg–11 Gd–4 Y–2 Zn–0.4 Zr alloy(GWZK114)were conducted at a deformation temperature range of 300–500°C and a strain rate range of 0.01–10.0 s-1.Based on systematic microstructure obs...Hot compression tests of Mg–11 Gd–4 Y–2 Zn–0.4 Zr alloy(GWZK114)were conducted at a deformation temperature range of 300–500°C and a strain rate range of 0.01–10.0 s-1.Based on systematic microstructure observation,it is confirmed that long period stacking ordered(LPSO)phase displays essential and evolving roles on the dynamic recrystallization(DRX)behavior.The results indicate that the plastic deformation is mainly coordinated by simultaneous exist of LPSO kinking of lamella 14 H-LPSO phase and DRX at 350–450℃,and DRX at 500℃.Further,it is found that the LPSO kinking induced during 350–450℃can delay the DRX.A phenomenological DRX model of GWZK114 alloy is established to be XDRX=1.exp[-0.5((ε-εc)/ε^*)0.91].Non-uniform distribution of plastic strain during compression was considered via finite element method and it ensures a good prediction of DRX fraction under a large plastic strain.Meanwhile,an enhanced DRX model,taking its formulation as XDRX={1.exp[-0.5((ε-εc)/ε*)0.91]}(T/(226.8)-1)n,n=3.82ε0.083,is proposed for the first time to capture the hindering effect of 14 H-LPSO kinking on DRX behavior.The predicted results of this enhanced DRX model agree well with the experimental cases,where 14 H-LPSO kinking is dominated or partially involved(300–450℃).Besides,a size model of DRX grains is also established and can depict the evolution of DRX grain size for all the investigated compression conditions with accounting for temperature rising at high strain rates(5 s^-1 and 10 s^-1).展开更多
基金The authors gratefully acknowledge the financial support by the Chinese National Science Foundation(No.50674038No.50974048)the HarBin Science and Technology Burean(No.2011RFQXG020).
文摘Mg-3.0Nd-0.4Zn-0.4Zr magnesium alloy were prepared by cast-extruding and chip-extruding.Microstructure,tensile and creep properties of the alloy were investigated.The results show that the alloy exhibit particle dynamic recrystallization during extrusion.The cast extruded-T6 rods at room temperature have a highest tensile strength of 258.5 MPa and a highest yield strength of 135.7 MPa.With the increase of test temperature,the strength of the alloy declines and the elongation increases.At 473 K,creep strain in the primary creep stage increases with increasing the creep stresses.Under 110 MPa,time spent during primary creep decreases with increasing the test temperatures.Stress exponent and creep activation energy of the alloy are 4.4 and 104 kJ/mol,respectively.Creep of the alloy can be controlled by dislocation climb mechanism.The morphology of the fracture surfaces was examined by employing scanning electron microscope.
基金financially supported by the National Nature Science Foundations of China(51464032)National Basic Research Program of China(Grant No.2010CB635106)
文摘A new rare earth magnesium alloy(Mg-6 Zn-4 Sm-0.4 Zr, wt.%) was prepared by permanent mould casting. The microstructure and mechanical properties of the alloy sample in as-cast and various heat treatment situations were characterized with an optical microscope(OM), X-ray diffractometer(XRD), scanning electron microscope(SEM) equipped with energy dispersive spectroscope(EDS), transmission electron microscope(TEM) and mechanical tests at room temperature, respectively. The experimental results show that the as-cast alloy mainly consists of α-Mg, eutectic Mg_2Zn_3, MgZnSm and Mg_(41)Sm_5. These eutectic phases with continuous or semicontinuous morphology principally distribute along grain boundaries. Almost all the eutectic compounds dissolve in α-Mg and the grains have no obvious growth trend after optimum solution treatment at 490 °C for 18 h. Meanwhile, the ultimate tensile strength(UTS) of 229 MPa and elongation(EL) to rupture of 9.78% can be achieved through the optimal solution treatment, which increase by 37 MPa and 57.74%, respectively, compared with that of the as-cast alloy. Further aging treatments at 200 °C for different durations lead to the conspicuous increment of mechanical properties and prominent age-hardening response. Peak-aged alloy(treated at 200 °C for 12 h) reveals better mechanical properties(UTS 258 MPa, EL 9.42%, hardness 73.4 HV) compared with the same alloy treated in other aging conditions, which is mainly ascribed to precipitated Mg_2Zn_3 and MgZn_2 phases. Fracture analysis demonstrates that the as-cast alloy belongs to inter-granular and cleavage fracture patterns, while the solutionized alloy(treated at 490 °C for 18 h) reveals trans-granular and quasi-cleavage fracture modes. For the peak-aged alloy, the fracture pattern obeys the mixture of trans-granular and cleavage modes.
文摘A Mg-6Zn-3Gd(mass fraction,%) alloy,noted as ZG63,was coated by different micro-arc oxidation(MAO) processes,and the coating structure and corrosion resistance of the alloy were studied using scanning electron microscopy(SEM),glancing angle X-ray diffractometry(GAXRD) and various electrochemical methods.The micro-arc oxidation process consists of three stages and corresponds with different coating structures.In the initial stage,the coating thickness is linearly increased and is controlled by electrochemical polarization.In the second stage,the coating grows mainly inward and accords with parabolic regularity.In the third stage,the loose coating forms and is controlled by local arc light.The looser coating is mainly composed of MgSiO3 and the compact coating is mainly composed of MgO.From micro-arc oxidation stage to local arc light stage,the corrosion resistance of the coated alloy firstly increases and then decreases.The satisfied corrosion resistance corresponds to the coating time ranging from 6 to10 min.
基金Funded by the Major State Basic Research Development Program of China(2016YFB0701405)the National Natural Science Foundation of China(51705314)
文摘Microstructure and mechanical behavior of the squeeze-casting and squeeze-casting plus T6 heat-treated Mg-8 Gd-2 Y-0.4 Zr magnesium alloys at room and elevated temperatures were investigated. The experimental results showed that the T6 treated alloy aged at slightly high temperature exhibited good comprehensive strength and ductility. However, the strength of the tested alloys was not sensitive to the change of tensile temperature, i e, the yield strength and ultimate tensile strength did not decrease significantly with increasing tensile temperature, while the ductility increased greatly. In addition, the squeeze-casting alloy exhibited predominant intergranular fracture accompanied by minor transgranular rupture, and the tensile fracture mode for the T6 treated alloy had typical transgranular cleavage fracture.
文摘Hot compression tests of Mg–11 Gd–4 Y–2 Zn–0.4 Zr alloy(GWZK114)were conducted at a deformation temperature range of 300–500°C and a strain rate range of 0.01–10.0 s-1.Based on systematic microstructure observation,it is confirmed that long period stacking ordered(LPSO)phase displays essential and evolving roles on the dynamic recrystallization(DRX)behavior.The results indicate that the plastic deformation is mainly coordinated by simultaneous exist of LPSO kinking of lamella 14 H-LPSO phase and DRX at 350–450℃,and DRX at 500℃.Further,it is found that the LPSO kinking induced during 350–450℃can delay the DRX.A phenomenological DRX model of GWZK114 alloy is established to be XDRX=1.exp[-0.5((ε-εc)/ε^*)0.91].Non-uniform distribution of plastic strain during compression was considered via finite element method and it ensures a good prediction of DRX fraction under a large plastic strain.Meanwhile,an enhanced DRX model,taking its formulation as XDRX={1.exp[-0.5((ε-εc)/ε*)0.91]}(T/(226.8)-1)n,n=3.82ε0.083,is proposed for the first time to capture the hindering effect of 14 H-LPSO kinking on DRX behavior.The predicted results of this enhanced DRX model agree well with the experimental cases,where 14 H-LPSO kinking is dominated or partially involved(300–450℃).Besides,a size model of DRX grains is also established and can depict the evolution of DRX grain size for all the investigated compression conditions with accounting for temperature rising at high strain rates(5 s^-1 and 10 s^-1).
