Role of micro-Ca/In alloying in tailoring the microstructural characteristics and discharge performance of dilute Mg-Bi-Sn-based alloys as anodes for Mg-air batteries

The influence of micro-Ca/In alloying on the microstructural charac teristics,electrochemical behaviors and discharge properties of extruded dilute Mg-0.5Bi-0.5Sn-based(wt.%)alloys as anodes for Mg-air batteries are evaluated.The grain size and texture intensity of the Mg-Bi-Sn-based alloys are significantly decreased after the Ca/In alloying,particularly for the In-containing alloy.Note that,in addition to nanoscale Mg_(3)Bi_(2)phase,a new microscale Mg_(2)Bi_(2)Ca phase forms in the Ca-containing alloy.The electrochemical test results demonstrate that Ca/In micro-alloying can enhance the electrochemical activity.Using In to alloy the Mg-Bi-Sn-based alloy is effective in restricting the cathodic hydrogen evolution(CHE)kinetics,leading to a low self-corrosion rate,while severe CHE occurred after Ca alloying.The micro-alloying of Ca/In to Mg-Bi-Sn-based alloy strongly deteriorates the compactness of discharge products film and mitigates the"chunk effect"(CE),hence the cell voltage,anodic efficiency as well as discharge capacity are greatly improved.The In-containing alloy exhibits outstanding discharge performance under the combined effect of the modified microstructure and discharge products,thus making it a potential anode material for primary Mg-air battery.

Properties of Ti-Based Hydrogen Storage Alloy

An efficient and safe hydrogen storage method is one of the important links for the large-scale development of hydrogen in the future. Because of its low price and simple design, Ti-based hydrogen storage alloys are considered to be suitable for practical applications. In this paper, we review the latest research on Ti-based hydrogen storage alloys. Firstly, the machine learning and density functional theory are introduced to provide theoretical guidance for the optimization of Ti-based hydrogen storage alloys. Then, in order to improve the hydrogen storage performance, we briefly introduce the research of AB type and AB2 type Ti-based alloys, focusing on doping elements and adaptive after treatment. Finally, suggestions for the future research and development of Ti-based hydrogen storage alloys are proposed. .

Hot corrosion behavior of Ni-xCr-6.8Al based alloys

The hot corrosion behaviors of as-cast and preoxidized Ni-xCr-6.8Al based alloys in the mixture of Na2SO4＋25% NaCl at 873 K were studied. The results show that the mass loss of Ni-xCr-6.8Al based alloys decreases with the increase of Cr content. Preoxidation improves the resistance to corrosion regardless of the concentration of Cr. The kinetics of as-cast Ni-12Cr-6.8Al and Ni-16Cr-6.8Al based alloys fits the parabolic law well, while that of the as-cast Ni-20Cr-6.8Al based alloy fits the power law. The kinetics of all the preoxidized samples obey the logarithmic law. The mechanism of the as-cast alloys can be well explained by the acid-base melting model. The behavior of the preoxidized alloys is found to be mainly determined by the properties of the oxide layer formed during the preoxidation to a large extend.

Effects of second phases on mechanical properties and martensitic transformations of ECAPed TiNi and Ti-Mo based shape memory alloys

TiNi and Ti-based shape memory alloys were processed by equal channel angular pressing （ECAP） at 673-773 K along Bc route to obtain ultrafine grains for increasing the strength of parent phase and improving the functional properties. The effects of both thermodynamically stable and metastable second phases on the mechanical properties and martensitic transformations of these alloys were investigated. It is found that thermodynamically stable Ti2Ni phase has no effect on martensitic transformation and superelasticity of Ti-rich TiNi alloy, thermodynamically stable α phase is harmful for ductility of Ti-Mo-Nb-V-Al alloy, but metastable Ti3Ni4 phase is effective for R phase transformation, martensitic transformation and superelasticity of Ni-rich TiNi alloy. The mechanisms of the second phases on the martensitic transformations and mechanical properties were discussed.

Hot corrosion behavior of Ni–16Cr–xAl based alloys in mixture of Na_2SO_4-NaCl at 600 ℃

The hot corrosion behaviors of Ni–16Cr–xAl（x=4.5%, 6.8%, 9.0%, mass fraction） based alloys in Na2SO4–25% NaCl molten salts at 600 °C were investigated. The effects of pre-oxidation and Al content on the resistance to hot corrosion were examined. The hot corrosion resistance of Ni–16Cr–xAl based alloy with Al addition from 4.5% to 9.0% increases with increasing Al content. The alloy with Al content of 9.0% shows the highest hot corrosion resistance among the examined alloys because more β–NiAl phases are obtained to sustain the Al2O3 scale repaired during hot corrosion. Pre-oxidized specimens have a superior hot corrosion resistance compared with the as-cast specimens, due to a protective oxide scale formed after pre-treatment.

Effect of Re element on oxidation resistance of Ni_3Al-Mo based alloys at 1150 ℃

The isothermal oxidation behaviors of three kinds of Ni3Al-Mo based alloys at 1150 ℃ were studied.The morphology,structure and element distribution of oxide scales of the alloys were researched by scanning electron microscopy,X-ray diffraction and electron probe microanalysis.The research results show that there are three oxide layers,an outer layer of NiO,an intermediate layer mainly composed of NiO,NiAl2O4 and a small amount of NiMoO4,and an inner layer of NiAl2O4 and Al2O3.Re element was mainly distributed in the intermediate layer,which plays a role as ＂diffusion barrier＂ in the process of oxidation,and effectively reduces the diffusion rate of Al and Mo elements outward and diffusion rate of O element inward.As a result,a Al-rich oxide layer formed in the inner layer inhibits the growth of oxide layer and improves the oxidation resistance of the alloy.

Crystal Nucleation and Growth of Al-based Alloys Produced by Electrolysis

The nucleation and growth of grains in a series of Al-based alloys produced by electrolysis are observed under SEM. The atomic Ti/AI ratios of the nuclei and the distribution of Ti at certain points are analyzed by point EDS. The particles in different atomic Ti/AI ratios might act as the nuclei of α-Al. At the early stage of growth, the spherical Ti-enriched regions might form around these particles within very limited temperature ranges in which the reactions such as the peritectic reactions etc occur. At the latter stage of growth, the dendrites freely develop in the radial orientations, and the concentration of Ti decreases linearly along the dendrite arm and becomes negligible in the region near the periphery of the dendrite. It is believed that the nucleation is closely related with the number and dispersion of primary spherical areas in the melts, and the segregation of Ti leads to the free growth of dendrite, which is necessary for the formation of equiaxial grains.

MICROSTRUCTURES OF TiAl BASED ALLOYS PREPARED BY HOT PRESSING ELEMENTAL POWDERS

１ＩＮＴＲＯＤＵＣＴＩＯＮＴｉＡｌｂａｓｅｄａｌｏｙｓｈａｖｅｂｅｅｎｒｅｇａｒｄｅｄａｓｐｒｏｍｉｓｉｎｇｈｉｇｈｔｅｍｐｅｒａｔｕｒｅｓｔｒｕｃｔｕｒｅｍａｔｅｒｉａｌｓ，ｆｏｒｔｈｅｉｒｈｉｇｈｓｐｅｃｉｆｉｃｓｔｒｅｎｇｔｈ，ｒｉｇｉｄｉｔｙ...

Tensile properties and fracture behavior of Ti_2AlNb based alloys at room temperature

The tensile mechanical properties and fracture behaviors of Ti 22Al 20Nb 7Ta alloys were studied at room temperature. Three typical microstructures of Ti 2AlNb based alloys were obtained by combination of thermal mechanical processing and heat treat ment. They are: 1) lath mixture of O + B 2 with remaining β grain boundaries and α 2 phase; 2) equiaxed O phase in B 2 matrix; 3) fine lath mixture of O + B 2 without remaining β grain boundaries. It is shown that the microstructure obviously affects the tensile properties of Ti 2AlNb based alloys. The microstructure of fine lath mixture of O + B 2 without remaining β grain boundaries has good combination of yield stress and ductility, while the microstructure with lath mixture of O + B 2 with remaining β grain boundaries and α 2 phase has low yield stress and elongation. The fracture mode was also controlled by the microstructure of Ti 2AlNb based alloys. By means of SEM, it was found that the dominated fracture mode of microstructure with lath mixture of O + B 2 with remained β grain boundary and α 2 phase was intergranular, and the fracture mode of the other two microstructures was mainly transgranular.

Effect of Nb additions on microstructure and properties of γ-TiAl based alloys fabricated by selective laser melting

The γ-TiAl based Ti.Al.Mn.Nb alloys with different Nb additions were fabricated by selective laser melting (SLM) on the TC4 substrate. The effects of Nb content on microstructure and properties of the alloys were investigated. The results reveal that the alloys consist of γ-TiAl phase with tetragonal lattice structure and α2-Ti3Al phase with hcp lattice structure, and show a sequential structure change from near full dendrite to near lamellar structure with the increase of Nb addition. Owing to the higher Nb content in γ-TiAl phase and the formation of near lamellar structure, the alloy with 7.0 at.% Nb addition has the best combination of properties among the studied alloys, namely, not only a high hardness of HV 2000, a high strength of 1390 MPa and a plastic deformation of about 24.5%, but also good tribological properties and high-temperature oxidation resistance.

Urinary levels of nickel and chromium associated with dental restoration by nickel-chromium based alloys

This paper aims to investigate if the dental restoration of nickel-chromium based alloy(Ni-Cr) leads to the enhanced excretions of Ni and Cr in urine.Seven hundred and ninety-five patients in a dental hospital had single or multiple Ni-Cr alloy restoration recently and 198 controls were recruited to collect information on dental restoration by questionnaire and clinical examination.Urinary concentrations of Ni and Cr from each subject were measure by graphite furnace atomic absorption spectrometry.Compared to the control group,the urinary level of Ni was significantly higher in the patient group of < 1 month of the restoration duration,among which higher Ni excretions were found in those with either a higher number of teeth replaced by dental alloys or a higher index of metal crown not covered with the porcelain.Urinary levels of Cr were significantly higher in the three patient groups of <1,1 to <3 and 3 to <6 months,especially in those with a higher metal crown exposure index.Linear curve estimations showed better relationships between urinary Ni and Cr in patients within 6-month groups.Our data suggested significant increased excretions of urinary Ni and Cr after dental restoration.Potential short- and long-term effects of Ni-Cr alloy restoration need to be investigated.

DEVELOPMENT OF MoS_2-CONTAINING Ni-Cr BASED ALLOYS AND THEIR HIGH-TEMPERATURE TRIBOLOGICAL PROPERTIES

ＤＥＶＥＬＯＰＭＥＮＴＯＦＭｏＳ２ＣＯＮＴＡＩＮＩＮＧＮｉＣｒＢＡＳＥＤＡＬＬＯＹＳＡＮＤＴＨＥＩＲＨＩＧＨＴＥＭＰＥＲＡＴＵＲＥＴＲＩＢＯＬＯＧＩＣＡＬＰＲＯＰＥＲＴＩＥＳ①ＸｉｏｎｇＤａｎｇｓｈｅｎｇＣｏｌｅｇｅｏｆＭｅｃｈａｎｉｃａｌＥｌ...

Microstructure and texture evolution of Ti-Nb-Si based alloys for biomedical applications

Microstructure and texture of Ti-Nb-Si based alloys, prepared by water quenching from β-phase field, cold rolling and recrystallization heat treatment followed by water quenching, were investigated in terms of optical microstructure and analysis of X-ray pole figure result. In as-quenched sample, relatively random distribution of pole figure was detected without showing a specific texture component. In as-cold rolled sample, however, it is found well-developed several texture components consisting of rotated cube, α-fiber and γ-fiber texture components which are frequently observed in bcc-structured metals and alloys were found. Therefore, texture components developed in the present alloys are closely related to the deformation of β-phase even though small amount of α″ phase co-exist in the microstructure. In recrystallized sample, α-fiber texture component is weakly detected while the other texture components, rotated cube and γ-fiber components, appears to be relatively unchanged. No additional texture components were detected besides those texture components observed in the cold rolled samples.

MICROSTRUCTURAL STABILITY OF LAMELLAR TiAl BASED ALLOYS AT HIGH TEMPERATURES

The microstructural stability of lamellar TiAl base alloys at high temperatures was studied by conventional and high resolution transmission electron microscopy. The influence of substructures on the thermal stability of lamellar structure was emphasized. These substructures produced by thermal mechanical treatments include the interfacial dislocations and ledges, the subgrain boundaries, the impinged T(Q) twins and misorientated lamellar interfaces. The microstructural change of three kinds of lamellar TiAl base alloys containing differents type and densities of substructures were compared during exposure at 800~1 000 ℃. It was found that the existence of such substructures could accelerate the degeneration of lamellar structure, leading to the rapid necking and break up of α 2 plates, the coarsening of γ plates, and the formation of new γ grains. As a result, the lamellar structure with substructures started to degenerate after thermal exposure at 800℃ for 4.5 h. While only slight coarsening was observed at the colony boundaries in the lamellar structure without substructures even after exposure at 900 ℃ for 7 d.

JOINING OF TiAl BASEDALLOYS BY HOT PRESSING

By hot pressing in an inert atmosphere, the joining interface between coarse lamellar structures and that between a coarse lamellar structure and a fine duplex structure of a Ti 33Al 3Cr(%, mass fraction) alloy, and the effect of heat treatment on the microstructure at the interfaces have been studied. The results showed that the microstructure at the interface between two coarse lamellar structures depends on the orientations of lamellae. And microcavities are found at such interfaces. After heat treatment at 1 250 ℃, the recrystallization structure widened. As to the interface between a coarse lamellar structure and a fine duplex structure, a new duplex structure formed within the original duplex structure at the interface and further widened after subsequent heat treatment at 1 250 ℃ for 4 h. Microcavities are rare at such interfaces, and the joining appears better than that between two coarse lamellar structures.

Effect of Al_(3)Zr particles on hot-compression behavior and processing map for Al-Cu-Li based alloys at elevated temperatures

The influence of Al3Zr particles on the hot compression behavior and processing map(PM)of Al-Cu-Li based alloys under isothermal plane-strain compression in the temperature range of 400-500℃and at the strain rates of 0.01-10 s^-1 was investigated.The corresponding microstructure was analyzed using optical microscopy(OM),electron back-scattered diffraction(EBSD)and transmission electron microscope(TEM).The results showed that dynamic recovery(DRV)played a greater role than dynamic recrystallization(DRX)in dynamic softening.At low temperatures,the Al3Zr particles were the significant barriers to inhibit DRV and DRX grain growth.When the temperature reached 500℃,the Al3Zr particles readily spread along grain boundaries just like a necklace due to the dissolution of Al3Zr particles and rapid diffusion of Zr through grain boundary,resulting in generating the macroscopic cracks and forming an instability domain at 490-500℃,0.01 s^-1 in the PM.

Effects of MoS_2 on mechanical and tribological properties of NiCr-based alloys

Ni Cr based alloys with a wide temperature range self lubrication were made by hot pressing the mixture powder of alloyed Ni Cr powder, elemental Mo, Al, Ti and B powders and MoS 2 powder. The mechanical and tribological properties of these alloys when rubbing with Al 2O 3 ceramics and W18Cr4V high speed steel were measured in the temperature range of 20～700 ℃, and the mechanisms of self lubrication and wear resistance were studied. The results showed that the alloy containing 10% MoS 2 has the best combination of mechanical properties, antifriction and wear resistance. Over a wide temperature range from 20 ℃ to 700 ℃, when rubbing with Al 2O 3, its friction coefficient and wear rate are 0.19～0.3 and (1.1～1.5)10 -14 m 3/(N·m), respectively; when rubbing with the high speed steel, those values are 0.18 ～ 0.26 and (0.6～3.2)×10 -15 m 3/(N·m), respectively.

STRENGTHENING MECHANISMSIN TiAl BASED ALLOYS

The influence of heat treatment and of thermomechanical processing on the structure and properties of a range of TiAl based alloys has been assessed and in agreement with other reports it has been found that increased refinement of the microstructure leads to improved mechanical strength at room temperature, both for the lamellar and the duplex structures. In the case of alloys cooled rapidly from the alpha phase field the increased refinement in lamellar spacing leads to significant increases in room temperature strength but thermomechanical processing can lead to far greater increases. The origin of this increase in strength in samples with a lamellar structure has been assessed in terms of the ability of dislocations to cross gamma/gamma and gamma/alpha 2 lamellar interfaces. It was concluded that the alpha 2 gamma interfaces and the alpha itself are important factors in strengthening the lamellar alloys. The stability of the various structures developed either by appropriate heat treatments or by thermomechanical processing has been investigated by exposing samples for a range of times at temperatures between 700 and 1 000 ℃. It has been found that the yield strength and the ultimate tensile strength generally decreased by about 20% during high temperature exposure at 700 ℃ for 3 000 h. The detailed behaviour on exposure at 700 ℃ has been found to be a function of alloy composition, with complex precipitates being formed in some alloys, but in all cases the amount of alpha 2 decreased with increased heat treatment time. It has been found that during exposure the alpha 2 lamellae decomposed to gamma phase by a mechanism that can involve the formation of thin gamma lamellae within the original alpha 2 lamellae.

EFFECT OF DYNAMIC RECRYSTALLIZATION ON SHAPE MEMORY EFFECT IN Fe－Mn－Si BASED ALLOYS

Improvement of shape, memory effect (SME) in Fe-Mn-Si based alloys has been investigated, compared with that by conventional 'training' treatment. It is found that SME in Fe-Mn-Si alloy can be greatly improved by ausforming and 3.8%recovery strain and 2.2% complete recovery strain can be reached by ausforming at 973 K when dynamic recrystallization has just occurred. The mechanism for the improvement of SME is proposed.

EFFECTS OF Ca ADDITIONON TiAl-BASED ALLOYS

ＥＦＦＥＣＴＳＯＦＣａＡＤＤＩＴＩＯＮＯＮＴｉＡｌＢＡＳＥＤＡＬＬＯＹＳ①①ＣａｏＰｅｎｇ，ＨｕａｎｇＢａｉｙｕｎ，ＨｅＹｕｅｈｕｉ，ＱｕＸｕａｎｈｕｉＰｏｗｄｅｒＭｅｔａｌｕｒｇｙＲｅｓｅａｒｃｈＩｎｓｔｉｔｕｔｅ，ＣｅｎｔｒａｌＳｏｕｔｈＵｎｉ...