Revealing the role of pyramidal slip in the high ductility of Mg-Li alloy

The high ductility of Mg-Li alloy has been mainly ascribed to a high activity of pyramidal<c+a>slip to accommodate plastic strain.In the present study,however,a quantitative analysis reveals that Li-addition can only slightly stimulate the activation of pyramidal<c+a>slip under compression along the normal direction of a hot-rolled Mg-4.5 wt.%Li plate,with a relative activity of approximately 18%.Although the limited activity of pyramidal<c+a>slip alone cannot accommodate a large plastic strain,it effectively reduces the number of{10.11}−{10.12}double twins,which are believed to be favorable sites for crack initiation.The evidently reduced activity of double twins leads to a lower cracking tendency,and therefore improves ductility.

Thermo-driven oleogel-based self-healing slippery surface behaving superior corrosion inhibition to Mg-Li alloy

Bioinspired by Nepenthes, lubricant infused surfaces(LIS) have attracted widespread attention in the field of anticorrosion. However,the lubricant coating has some disadvantages such as complex construction processing and easy loss of oil phase in air or dynamic water phase. In this study, oleogel is infused into a lotus leaf inspired super-hydrophobic matrix to form an oleogel infused surface(OIS) for enhancing corrosion resistance of active Mg-Li alloy. For reserving oleogel, firstly, a facile one-step electrodeposition method is used to construct super-hydrophobic surface(SHS) composed by samarium/myristic acid complex micro-nano flower structure onto Mg-Li alloy.The coating exhibits excellent superhydrophobic property at a static contact angle of 160° by applying 30 V electrolysis for 30 min. The protection efficiency of single SHS highly relates with the metal itself. For short period immersion in water phase, SHS can afford protection to Mg-Li alloy. However, the long-term immersion will see the rapid failure of SHS, and the high activity of Mg-Li alloy is one main reason.We assume that SHS cannot be a good choice for protecting Mg-Li alloy. Then, a Nepenthes inspired liquid coating is formed by infusing oleogel into the micro-nano structure by a spin-coating method. The liquid coating performs prominent corrosion resistance with Rctreaching as high as 1.51 × 10^(10)Ω cm^(2). After the mechanical damage from the external environment, the liquid coating can realize self-repair through thermal assistance, and the liquid coating can still restore Rctup to 1.24 × 10^(10)Ω cm^(2) after healing. The corrosion resistance of the liquid coating remains strong by showing Rctas high as 1.14 × 10^(9)Ω cm^(2), even after immersion in representative corrosive 3.5 wt% Na Cl solution for 30 d.

Influence of deformation on the corrosion behavior of LZ91 Mg-Li alloy

The effect of rolling and forging on the microstructure and corrosion behavior of LZ91 alloy was investigated using an electron probe micro-analyzer,immersion and electrochemical tests.Results showed that the area fraction of theβ-Li phase remained unchanged,and the grain size of theβ-Li phase decreased after forging.The as-rolled forged alloy(FR-LZ91)exhibited the highest area fraction of theβ-Li phase and the longest grains.The corrosion resistance of the forged LZ91 alloy increased due to grain refinement that prevented further corrosion during the immersion test.Among the experimental alloys,FR-LZ91 showed the highest resistance of corrosion film and charge transfer resistance values due to its protective film caused by the high area fraction of theβ-Li phase.

Rolling texture development in a dual-phase Mg-Li alloy:The role of temperature

Dual-phase Mg-Li alloys sheets were rolled at four different temperatures ranging from liquid nitrogen to 300℃to explore effect of rolling temperature on texture and mechanical properties of the material.Crystal plasticity simulation was utilized to illustrate the influence of slip activity on rolling texture development.The results show that the rolling texture is largely depended on deformation temperature.Unlike commercial Mg alloys,the critical resolved shear stress of basal slip inα-Mg phase of Mg-Li alloy decreased more significantly by increasing temperature compared to that of pyramidal<c+a>slip.Enhancement of basal slip by increasing temperature triggered a decrease of split angle of basal poles for the double-peak texture.Prismaticslip largely enhanced by increasing temperature upon 200℃,which induced a wider orientation spread along the transverse direction.For theβ-Li phase,the promotion of{110}<111>slip system at elevated temperature triggered the enhancement of{211}<110>and{111}<211>texture components.The cryo-rolled sample exhibited the highest strength compared to the others due to a strong hardening behavior at this temperature.A two-stage hardening behavior was observed in these as-rolled dual-phase alloys.Strain transition at phase boundaries could be the reason for appearance of this two-stage hardening.

Influence of Rare Earth Elements on Microstructure and Mechanical Properties of Mg-Li Alloys

A series of a-based Mg-Li-A1-Zn-xRE alloys were prepared. These alloys have low density ranging from 1.5 to 1.7 g·cm^-3 and high strength properties. The influence of RE element on the microstructure and the mechanical properties of these alloys were studied. The results indicate that the addition of RE （La, Pr, Ce） leads to the formation of rodshaped intermetallic compound Al2Zn2La distributed in the matrix. Al2Zn2La induces reduction of the laminar spacing and causes refinement of the microstructure. Therefore, this compound improves the strength of alloys at a high temperature.

Micro-arc oxidation coatings on Mg-Li alloys

Micro-arc oxidation (MAO) method was used for the surface modification of an Mg-5wt.%Li alloy. Ceramic coatings were in-situ fabricated on the Mg-Li alloy. The morphology feature,phase composition,and corrosion-resistance of the formed ceramic coatings were studied by SEM,XRD,and electrochemical methods,respectively. The results showed that the coatings produced in a sodium silicate solution system were composed of MgO and Mg2SiO4. The ceramic coating became thicker and the content of Mg2SiO4 phase increased as the concentration of Na2SiO3 increased in the solution. The coating was loose at the low concentration of Na2SiO3 and was compact at the high concentration of Na2SiO3. The coated samples had a better corrosion resistance than the Mg-Li substrate in terms of the Tafel polarization curves and the cyclic voltammetry curves (CV).

Cerium Chemical Conversion Coating on a Novel Mg-Li Alloy

A novel Mg-Li alloy was treated in a cerium nitrate solution and cerium chemical conversion coating was obtained on the alloy. Then the forming process, structure and corrosion resistance of the coating were investigated. The influential factors of cerium conversion coating were discussed through orthogonal experiments, and the optimum processing parameters were confirmed. XPS spectra displayed that the conversion coating consisted of cerium compounds, and the major component of the protective layer was a mixture of Ce （IV） oxide and Ce （IV） hydroxide. In addition, XRD pattern illustrated that there was crystalline CeO2 in the conversion coating. Analysis by SEM showed that the cerium conversion coating was uniform with a fiber-like morphology. The thickness of the conversion coating was 12 μm. The results of electrochemical potentiodynamic polarization and hydrogen evolution measurement indicated that the cerium conversion coating provided effective protection to the novel Mg-Li alloy.

Preparation of Mg-Li alloys by electrolysis in molten salt at low temperature

A new technology for preparation of low cost Mg-Li alloys was studied. The alloys were prepared by electrolysis in molten LiCl-KCl （weight ratio is 1：1） electrolyte with Mg rod severing as the consumed cathode. Main factors that affect current efficiency were investigated, and optimal electrolysis parameters were obtained. Mg-Li alloys with low lithium Content （about 25%） were prepared by the unique method of a higher post-thermal treatment temperature after electrolysis at low temperature. The results showed that the electrolysis can be carried out at low temperature, which resulted in reducing preparation cost due to energy saving. The new technology for the oreoaration of Mg-Li alloy by electrolysis in molten salt was laroved to be feasible.

Electrochemical formation and phase control of Mg-Li alloys

The electrochemical formation of Mg-Li alloys was investigated in a molten LiCl-KCl (58-42 mol%) eutectic melt at 723 K. The cyclic voltammogram. for a Mo electrode showed that the electroreduction of Li+ proceeds in a single step and the deposition potential of Li metal was -2.40 V (vs. Ag/AgCl). For Mg electrode, the electroreduction of Li+ takes place at less cathodic potential than that at the Mo electrode which was caused by the formation of Mg-Li alloys. Phase of the deposited Mg-Li alloys could be controlled by the electrolysis potential, and the samples were characterized by X-ray diffraction and scanning electron microscopy. The results showed that alpha-Mg and beta-Li phases were obtained at -2.35 and -2.55 V, respectively. (c) 2007 Mi Lin Zhang. Published by Elsevier B.V. on behalf of Chinese Chemical Society. All rights reserved.

Microstructure, cold rolling, heat treatment, and mechanical properties of Mg-Li alloys

The magnesium-lithium （Mg-Li） alloy exhibits two phase structures between 5.7wt% and 10.3wt% Li contents, consisting of the a （hcp） Mg-rich and the β （bcc） Li-rich phases, at room temperature. In the experiment, Mg-5Li-2Zn, Mg-9Li-2Zn, Mg-16Li-2Zn, Mg-22Li-2Zn, Mg-5Li-2Zn-2Ca, Mg-9Li-2Zn-2Ca, Mg-16Li-2Zn-2Ca, and Mg-22Li-2Zn-2Ca （wt%） were melted. During the melting process, the flux, which was composed of lithium chloride （LiCl） and lithium fluoride （LiF） in the proportion of 3：1 （mass ratio） and argon gas were used to protect the alloys from oxidation. The microstructure, mechanical properties, and cold-rolling workability of the wrought alloys were studied. The crystal grain of the alloys （adding Ga） is fine . The hardness of the studied alloys decreases with an increase in element Li. The density of the studied alloys is in the range of 1.187 to 1.617 g/cm^3. The reduction of the Mg-16Li-2Zn and Mg-22Li-2Zn alloys can exceed 85% at room temperature. The Mg-9Li-2Zn-2Ca alloy was heat treated at 300℃ for 8, 12, 16, and 24 h, respectively. The optimum heat treatment of the Mg-9Li-2Zn-2Ca alloy is 300℃×12h by metallographic observation and by studying the mechanical properties of the alloys.

Quasi-in-situ study on{10-12}twinning-detwinning behavior of rolled Mg-Li alloy in two-step compression(RD)-compression(ND)process

Twinning-detwinning(TDT)behavior in a strongly basal-textured Mg-Li alloy during two-step compression(RD)-compression(ND)process was investigated using quasi-in-situ EBSD.TDT behavior and TDT variants selection were statistically discussed with the loading path for the first time.Non-Schmid twinning behavior was observed in the first step compression,owing to the local stress fluctuations by neighboring twins;in contrast,Schmid’s law well predicted the detwinning variants selection.This asymmetrical TDT behavior was first investigated to date related with the strong basal texture and loading path.Besides,with the progress of compression,Schmid factors for twinning demonstrated a decreasing tendency;however,those for detwinning during the second step displayed an abnormally increasing trend,fundamentally stemming from prior twinning behavior.

Design of an age hardening Mg-Li alloy and its aging behavior

An effort was made to design an age hardening Mg-Li alloy based on the phase diagrams calculated by means of 'THERMO-CALC'—a thermodynamic software. Experiments were carried out to verify the calculated results by melting the alloy and examining its structure and aging behavior. The results show that the alloy possesses a structure constituent as expected, besides, the alloy has apparent aging behavior and over aging happens even at lower temperature. Metastable (Mg, Li, Al, Zn) phase has been identified when the hardness reaches the aging peak. With the increase of the aging time, (Mg, Li, Al, Zn) phase transforms to stable α phase and over aging happens.

Study on Phytic Acid Conversion Coating on Mg-Li Alloy

The impact of phytic acid concentration,immersion time and soaking temperature on phytic acid conversion coating of the Mg-Li alloy are studied.The surface morphology and the corrosion of the phytic acid conversion coating are tested by using scanning electron microscopy and the electrochemical analyzer.The results show that phytic acid concentration and immersion time,soaking temperature affects the microstructure and corrosion resistance of the phytic acid conversion coating.There is a passivation interval with a smaller capacitor and larger resistor in the phytic acid conversion coating.The phytic acid conversion coating is made up of white particle and flake film.

A comparison of the microstructure-dependent corrosion of dual-structured Mg-Li alloys fabricated by powder consolidation methods:Laser powder bed fusion vs pulse plasma sintering

In this study, powder metallurgy methods were used to fabricate Mg-7.5Li-3Al-Zn alloys from repowdered extruded alloys. Extruded alloys were powdered using ultrasonic atomization, and then laser powder bed fusion(LPBF) and pulse plasma sintering(PPS) were used to consolidate the bulk materials. A comparison of the properties of the fabricated alloys with those of a conventionally extruded one was carried out using methods that characterized the microstructure and corrosion resistance. When compared to their conventionally extruded counterpart, LPBF and PPS materials exhibited refined microstructures with low enrichment in Al Li and coarse Al, Zn, Mn precipitates. The main drawback of the LPBF alloy, printed for the needs of this study, was its porosity, which had a negative effect on its corrosion. The presence of unrecrystallized particle boundaries in the PPS alloy was also unbeneficial with regard to corrosion. The advantage of the LPBF and PPS processes was the ability to change the proportion of α(Mg) to β(Li), which when the complete consolidation of the material is achievable, may increase the corrosion resistance of dual-structured Mg-Li alloys. The results show that powder metallurgy routes have a wide potential to be used for the manufacture of Mg-Li based alloys.

Electrochemical codeposition of typical α+β phases Mg-Li alloys from the molten LiCl-KCl-MgCl_2 system

Electrochemical codeposition of Mg-Li alloys on molybdenum electrodes was investigated in LiCl-KCl（50 wt.%：50 wt.%） melts containing different concentrations of MgCl2 at 973 K.Cyclic voltammograms show that the underpotential deposition of lithium on pre-deposited magnesium leads to the formation of liquid Mg-Li alloys.The deposition potentials of Mg（II） and Li（I） ions gradually near each other with MgCl2 concentration decreasing.Mg-Li alloys with typical α ＋ β phases could be obtained by potentiostatic electrolysis from LiCl-KCl melts containing 5 wt.% MgCl2 at -2.25 V vs.Ag/AgCl（cathodic current density 1.70 A·cm-2） for 2.5 h.α phase, α ＋ β phases, and β phase Mg-Li alloys with different lithium contents were obtained by potentiostatic electrolysis from LiCl-KCl melts with the different concentrations of MgCl2.The samples were characterized by X-ray diffraction and scanning electron microscopy.

MICROSTRUCTURE AND MECHANICAL PROPERTIES OF Mg-Li ALLOY WITH Ca ADDITION

Mg-9wt%Li-2wt%Zn alloy was prepared and studied in this article. The addition of Ca to the alloy from 0.1wt% to 1wt% can refine the α-Mg and the best effect of refinement occurs when Ca content is 0.4wt%-0.5wt%. The billets can be rolled to thin sheets at room temperature, from which it is obvious that the addition of Ca improves alloys ormalin. while it decreases with the excess addition of Ca. The results also show that the ultimate tensile strength （UTS） and yield strength （YS） of the alloy with lwt% Ca may rise by 28% and 25%, respectively, however, the elongation decreases. It is clarified that the adsorption of proper Ca on the grain boundaries refines α-Mg and improves the tensile properties, but the presence of excess Ca and stable Ca2Mg6Zn3phase worsens the elongation.

Comparison of Properties between Phytic Acid and RE-phytic Conversion Coatings of Mg-Li Alloy

The properties among of phytic acid conversion coatings,RE-phytic conversion coatings,rare earth conversion coatings and chromate conversion coatings were compared.The surface micrograph and the corrosion morphology of matrix and various coatings were observed,and the polarization curve,amount of hydrogen evolution and coating binding force were tested.The infrared spectra of phytic acid solution,phytic acid conversion coatings and RE-phytic conversion coatings were compared.The results indicated that the phytic acid coating and RE-phytic acid coating have better corrosion resistance and the RE-phytic acid coating is much better.The infrared spectra indicated that the characteristic peak of phytic acid conversion coatings shift left compared to that of phytic acid.The characteristic peak of RE-phytic conversion coating is similar with that of the phytic acid conversion coating.The di-hydrogen phosphate group of phytic acid reacted with metal matrix or rare earth conversion coating to generate hydrophosphate or phosphate.Phytic acid conversion coating consists of magnesium salt,aluminum salt,zinc salt and ferrous salt.The RE-phytic coating contains cerium salt besides those salts.

Rolling route for refining grains of super light Mg-Li alloys containing Sc and Be

Pioneering work on Sc or/and Be added Mg-Li alloys with refined grains was initiated.Various rolling-based thermo-mechanical treatments on these Mg-Li alloys were carried out.Four Mg-Li alloys were prepared by vacuum melting process.A unique route for producing fine grains was applied which concluded solution treatment at 350°C,cold rolling with 60% thickness reduction and 250°C annealing,successively.

Microstructure, mechanical properties and age-hardening of Mg-Li alloy sheets

Mg-(5-22)(mass fraction, %)Li alloys with Zn addition were produced and studied. The density of studied alloys is 1.19-1.62 g/cm3. It is found that the alloy has excellent cold-workability and can be rolled to thin sheets at room temperature. The tensile tests were carried out at various tensile temperatures and strain rates. It is remarkable that the superplasticity occurs during uniaxial tensions at 150℃. In addition, the sheet is very sensitive to strain-rate even at room temperature. The age-hardening of the sheets at room temperature and 50℃was investigated. The hardening may be caused by the precipitation of MgLi2Zn phase, and overaging occurs owing to the phase transformation from MgLi2Zn to MgLiZn observed by X-ray diffractometry.

Crack propagation of Mg-Li alloys by impact load

Under impact load,using energy estimation and updated finite element method,the crack propagation of Mg-Li alloys was studied,and the relations between high speed impact,time interval and crack propagation velocity were deduced. The effects of impact pattern characteristic parameters such as impact range and time interval on impact fatigue crack growth and propagation rates were discussed. The results show that with the development of crack length,the crack propagation rate along the central sample alloy swiftly increases to the maximum. Then,the crack of other parts has different rate variations. The calculation and simulation results fit well with the experimental ones,which verifies the validity of energy estimation and updated finite element analysis. Impact loading usually induces materials and accelerates the fatigue crack growth.