Alloying elements, present in the aluminum solid solution or the precipitates, influence the corrosion resistance of A1-Mg-Mn-Zn alloys. In this study, sensi- tizing treatment was applied to an A1-Mg-Mn-Zn alloy to mo...Alloying elements, present in the aluminum solid solution or the precipitates, influence the corrosion resistance of A1-Mg-Mn-Zn alloys. In this study, sensi- tizing treatment was applied to an A1-Mg-Mn-Zn alloy to modify the precipitation at the grain boundaries or in the grains. Transmission electron microscopy （TEM） and scanning electron microscope （SEM） were used to characterize various second-phase particles and determine their orientation relationship with the A1 matrix. After sensitizing treatment, z-phase （Mg32（Al, Zn）49） is observed to precipitate along the grain boundaries in a coarser size, producing a discontinuous grain boundary precipitate structure. In addition, Mn-rich particles are found to form with various shapes, such as global, plate and rhombus.展开更多
The effects of Y on the microstructure and mechanical properties of Mg-6Zn-lMn alloy were investigated. The results show that the addition of Y has significant effect on the phase composition, microstructure and mecha...The effects of Y on the microstructure and mechanical properties of Mg-6Zn-lMn alloy were investigated. The results show that the addition of Y has significant effect on the phase composition, microstructure and mechanical properties of Mg-6Zn-lMn alloy. Varied phases compositions, including Mg7Zn3, I-phase （Mg3YZn6）, W-phase （Mg3Y2Zn3） and X-phase （MgI2YZn）, are obtained by adjusting the Zn to Y mass ratio. Mn element exists as the fine Mn particles, which are well distributed in the alloy. Thermal analysis and microstructure observation reveal that the phase stability follows the trend of X〉W〉/〉MgTZn3. In addition, Y can improve the mechanical properties of Mg-Zn-Mn alloy significantly, and the alloy with Y content of 6.09% has the best mechanical properties. The high strength is mainly due to the strengthening by the grain size refinement, dispersion strengthening by fine Mn particles, and introduction of the Mg-Zn-Y ternary phases.展开更多
The roles of Zn content and thermo-mechanical treatment in affecting microstructures and mechanical properties of Mg-x%Zn-1%Mn（mass fraction,x=4,5,6,7,8,9） wrought Mg alloys were investigated.The microstructure was ...The roles of Zn content and thermo-mechanical treatment in affecting microstructures and mechanical properties of Mg-x%Zn-1%Mn（mass fraction,x=4,5,6,7,8,9） wrought Mg alloys were investigated.The microstructure was extremely refined by dynamic recrystallization（DRC） during extrusion.With increasing Zn content,the DRC grains tended to grow up,at the same time,more second phase streamlines would be present,which restricted the further growing.During solution treatment,the DRC grains would rapidly grow up;however,higher Zn content could hinder the grain boundary expanding,which results in finer ultimate grains.MgZn2 dispersoid particles which are coherent with the matrix would precipitate from the supersaturated solid solution during the one-step aging process,and nano-sized GP zones formed during the pre-aging stage of the two-step aging provide a huge amount of effective nuclei for the MgZn2 phases formed in the second stage,which makes the MgZn2 particles much finer and more dispersed.The mechanical properties of as-extruded samples were not so sensitive to the variation of Zn content,the tensile strength fluctuates between 300 and 320 MPa,and the elongation maintains a high value between 11% and 14%.The strength of aged samples rises as a parabolic curve with increasing Zn content,specifically,the tensile strength of one-step aged samples rises from 278 to 374 MPa,and that of two-step aged ones rises from 284 to 378 MPa,yet the elongation of all aged samples is below 8%.When Zn content exceeds its solid solution limit in Mg-Zn system（6.2%,mass fraction）,the strength rises slowly but the elongation deteriorates sharply,so a Mg-Zn-Mn alloy with 6% Zn possesses the best mechanical properties,that is,the tensile strengths after one-and two-step aging are 352 and 366 MPa,respectively,and the corresponding elongations are 7.98% and 5.2%,respectively.展开更多
The microstructures and mechanical properties of Mg-6Zn-1Mn-4Sn and Mg-6Zn-1Mn-4Sn-0.5Y alloys under extrusion and T6 aging conditions were investigated by optical microscopy（OM）, X-ray diffraction（XRD）, scanning ...The microstructures and mechanical properties of Mg-6Zn-1Mn-4Sn and Mg-6Zn-1Mn-4Sn-0.5Y alloys under extrusion and T6 aging conditions were investigated by optical microscopy（OM）, X-ray diffraction（XRD）, scanning electron microscopy（SEM） and tensile test. The results show that Y element refines the grains and improves the comprehensive mechanical properties of ZMT614-0.5Y both in as-extruded and T6 states. The phase compositions of Mg-6Zn-1Mn-4Sn-0.5Y are α-Mg, Mg Zn2, Mn, Mg2 Sn and Mg Sn Y phases. After T6 treatment, the ultimate tensile strength（UTS） and yield strength（YS） increase while the elongation decreases severely. For both of these alloys, the theoretical results combined with the experimental values demonstrate that the grain boundary strengthening and solid solution strengthening play an important role in enhancing the YS in the as-extruded state, while the precipitation strengthening is the key factor for the enhancement of YS in the T6 state.展开更多
基金financially supported by the National Natural Science Foundation of China (No.51301017)the Common Construction Project from Beijing Municipal Commission of Education
文摘Alloying elements, present in the aluminum solid solution or the precipitates, influence the corrosion resistance of A1-Mg-Mn-Zn alloys. In this study, sensi- tizing treatment was applied to an A1-Mg-Mn-Zn alloy to modify the precipitation at the grain boundaries or in the grains. Transmission electron microscopy （TEM） and scanning electron microscope （SEM） were used to characterize various second-phase particles and determine their orientation relationship with the A1 matrix. After sensitizing treatment, z-phase （Mg32（Al, Zn）49） is observed to precipitate along the grain boundaries in a coarser size, producing a discontinuous grain boundary precipitate structure. In addition, Mn-rich particles are found to form with various shapes, such as global, plate and rhombus.
基金Project(2007CB613700)supported by the National Basic Research Program of ChinaProject(2011BAE22B01-3)supported by the National Key Technologies R&D Program of China+1 种基金Project(2010DFR50010,2008DFR50040)supported by the International Scientific and Technological Cooperation Program of Ministry of Science and Technology of ChinaProject(CSTC,2010AA4048)supported by Chongqing Science and Technology Commission,China
文摘The effects of Y on the microstructure and mechanical properties of Mg-6Zn-lMn alloy were investigated. The results show that the addition of Y has significant effect on the phase composition, microstructure and mechanical properties of Mg-6Zn-lMn alloy. Varied phases compositions, including Mg7Zn3, I-phase （Mg3YZn6）, W-phase （Mg3Y2Zn3） and X-phase （MgI2YZn）, are obtained by adjusting the Zn to Y mass ratio. Mn element exists as the fine Mn particles, which are well distributed in the alloy. Thermal analysis and microstructure observation reveal that the phase stability follows the trend of X〉W〉/〉MgTZn3. In addition, Y can improve the mechanical properties of Mg-Zn-Mn alloy significantly, and the alloy with Y content of 6.09% has the best mechanical properties. The high strength is mainly due to the strengthening by the grain size refinement, dispersion strengthening by fine Mn particles, and introduction of the Mg-Zn-Y ternary phases.
基金Project(2007CB613700)supported by the National Basic Research Program of ChinaProject(2007BAG06B04)supported by the National Science and Technology Pillar Program During the 11th Five-Year Plan Period,China+1 种基金Project(50725413)supported by the National Natural Science Foundation of ChinaProject(CDJXS10132202)supported by the Fundamental Research Funds for the Central Universities,China
文摘The roles of Zn content and thermo-mechanical treatment in affecting microstructures and mechanical properties of Mg-x%Zn-1%Mn（mass fraction,x=4,5,6,7,8,9） wrought Mg alloys were investigated.The microstructure was extremely refined by dynamic recrystallization（DRC） during extrusion.With increasing Zn content,the DRC grains tended to grow up,at the same time,more second phase streamlines would be present,which restricted the further growing.During solution treatment,the DRC grains would rapidly grow up;however,higher Zn content could hinder the grain boundary expanding,which results in finer ultimate grains.MgZn2 dispersoid particles which are coherent with the matrix would precipitate from the supersaturated solid solution during the one-step aging process,and nano-sized GP zones formed during the pre-aging stage of the two-step aging provide a huge amount of effective nuclei for the MgZn2 phases formed in the second stage,which makes the MgZn2 particles much finer and more dispersed.The mechanical properties of as-extruded samples were not so sensitive to the variation of Zn content,the tensile strength fluctuates between 300 and 320 MPa,and the elongation maintains a high value between 11% and 14%.The strength of aged samples rises as a parabolic curve with increasing Zn content,specifically,the tensile strength of one-step aged samples rises from 278 to 374 MPa,and that of two-step aged ones rises from 284 to 378 MPa,yet the elongation of all aged samples is below 8%.When Zn content exceeds its solid solution limit in Mg-Zn system（6.2%,mass fraction）,the strength rises slowly but the elongation deteriorates sharply,so a Mg-Zn-Mn alloy with 6% Zn possesses the best mechanical properties,that is,the tensile strengths after one-and two-step aging are 352 and 366 MPa,respectively,and the corresponding elongations are 7.98% and 5.2%,respectively.
基金Project(2013CB632200)supported by National Basic Research Program of ChinaProject(2010DFR50010)supported by International Scientific and Technological Cooperation Program of Ministry of Science and Technology of ChinaProject supported by Sharing Fund of Chongqing University’s Large-scale Equipment,China
文摘The microstructures and mechanical properties of Mg-6Zn-1Mn-4Sn and Mg-6Zn-1Mn-4Sn-0.5Y alloys under extrusion and T6 aging conditions were investigated by optical microscopy（OM）, X-ray diffraction（XRD）, scanning electron microscopy（SEM） and tensile test. The results show that Y element refines the grains and improves the comprehensive mechanical properties of ZMT614-0.5Y both in as-extruded and T6 states. The phase compositions of Mg-6Zn-1Mn-4Sn-0.5Y are α-Mg, Mg Zn2, Mn, Mg2 Sn and Mg Sn Y phases. After T6 treatment, the ultimate tensile strength（UTS） and yield strength（YS） increase while the elongation decreases severely. For both of these alloys, the theoretical results combined with the experimental values demonstrate that the grain boundary strengthening and solid solution strengthening play an important role in enhancing the YS in the as-extruded state, while the precipitation strengthening is the key factor for the enhancement of YS in the T6 state.
