A new type of Ni/MgO catalyst was prepared using atmospheric high-frequency discharge cold plasma. The influences of conventional method, plasma method, and plasma plus calcination method on the catalytic activity wer...A new type of Ni/MgO catalyst was prepared using atmospheric high-frequency discharge cold plasma. The influences of conventional method, plasma method, and plasma plus calcination method on the catalytic activity were studied and the CO2 reforming of methane was chosen as the probe reaction. The catalysts were characterized by X-ray diffraction （XRD）, transmission electron microscope （TEM）, X-ray photoelectron spectroscopy, and CO2 temperature-programmed surface reaction techniques. The results suggested that the nickel-based catalyst prepared by plasma plus calcination method possessed a smaller particle size and a higher dispersion of active component, better low-temperature activity and enhanced anti-coking ability. The conversion of CO2 and CH4 was 90.70% and 89.37%, respectively, and the reaction lasted for 36 h without obvious deactivation under 101.325 kPa and 750°C with CO2/CH4 = 1/1.展开更多
Sulphur-containing aromatic amines were prepared efficiently in good to excellent yields by reduction of the corresponding sulphur-containing aromatic nitro compounds with hydrazine hydrate in the presence of iron（Ⅲ...Sulphur-containing aromatic amines were prepared efficiently in good to excellent yields by reduction of the corresponding sulphur-containing aromatic nitro compounds with hydrazine hydrate in the presence of iron（Ⅲ） oxide-MgO catalyst. The catalyst exhibited high activity and stability for the reduction of sulphur-containing aromatic nitro compounds. The yields of sulphur-containing aromatic amines were up to 91-99 % at 355 K after reduction for 1-4 h over this catalyst.展开更多
Pt-CeO2-ZrO2/MgO （Pt-CZ/MgO） catalysts with 0.8 wt% Pt, 3.0 wt% CeO2 and 3.0 wt% ZrO2 were prepared by wet impregnation method. Support MgO was obtained using ion exchange resin method or using commercial MgO. XRD, ...Pt-CeO2-ZrO2/MgO （Pt-CZ/MgO） catalysts with 0.8 wt% Pt, 3.0 wt% CeO2 and 3.0 wt% ZrO2 were prepared by wet impregnation method. Support MgO was obtained using ion exchange resin method or using commercial MgO. XRD, BET, SEM, TEM, DTA-TG and CO2-TPD were used to characterize the catalysts. CH4-CO2 reforming to synthesis gas （syngas） was performed to test the catalytic behavior of the catalysts. The catalyst Pt-CZ/MgO-IE（D） prepared using ion exchange resin exhibits more regular structure, smaller and more unique particle sizes, and stronger basicity than the catalyst Pt-CZ/MgO prepared from commercial MgO. At 1073 K and atmospheric pressure, Pt-CZ/MgO-IE（D） catalyst has a higher activity and greater stability than Pt-CZ/MgO catalyst for CH4-CO2 reforming reaction at high gas hourly space velocity of 36000 mL/（g.h） with a stoichiometric feed of CH4 and C02. Activity measurement and characterization results demonstrate that modification of the support using ion exchange resin method can promote the surface structural property and stability, therefore enhancing the activity and stability for CH4-CO2 reforming reaction.展开更多
Ab initio calculations based on density functional theory have been used to study thedecompsition of N_2O on MgO. The reaction is predicted to occur on O_3c and O_(4c) atoms, but not onO_(5c) atoms, with an activation...Ab initio calculations based on density functional theory have been used to study thedecompsition of N_2O on MgO. The reaction is predicted to occur on O_3c and O_(4c) atoms, but not onO_(5c) atoms, with an activation barrier of 25-27 kcal/mol, in agreement with the experimental valueof 35 kcal/mol. Natural bond orbital analysis shows that the reaction leaves O ad-atoms on thosesurface O anions to form a peroxide-like 'O^2_(2-)' species. The )O-O bond stretching frequency ispredicted to be in the range from 820 cm(-1) to 825 cm(-1).展开更多
The structures and catalytic performances of V_2O_5, Mg_3V_2O_8 and V/MgO catalysts have been correlated by means of XRD, FTIR, TPR and flow micro-reactor tests. The postulation about active site has been made. Based ...The structures and catalytic performances of V_2O_5, Mg_3V_2O_8 and V/MgO catalysts have been correlated by means of XRD, FTIR, TPR and flow micro-reactor tests. The postulation about active site has been made. Based on it, better catalysts have been first prepared via grafting and modification with Sb which are better than that via impregnation.展开更多
Carbon deposition is sensitive to the metal particle sizes of supported Ni catalysts in CH_4/CO_2 reforming.To explore the reason of this phenomenon,Ni4,Ni8,and Ni12 which re flect the different cluster thicknesses su...Carbon deposition is sensitive to the metal particle sizes of supported Ni catalysts in CH_4/CO_2 reforming.To explore the reason of this phenomenon,Ni4,Ni8,and Ni12 which re flect the different cluster thicknesses supported on the MgO(100) slabs,have been employed to simulate Ni/MgO catalysts,and the reaction pathways of CH_4/CO_2 reforming on Nix/MgO(100) models are investigated by density functional theory.The reforming mechanisms of CH_4/CO_2 on different Nix/MgO(100) indicate the energy barriers of CH_4 dissociated adsorption,CH dissociation,and C oxidation three factors are all declining with the decrease of the Ni cluster sizes.The Hirshfeld charges analyses of three steps as described above show only Ni atoms in bottom two layers can obtain electrons from the MgO supporters,and the main electron transfer occurs between adsorbed species and their directly contacted Ni atoms.Due to more electron-rich Ni atoms in contact with the MgO supporters,the Ni/MgO catalysts with small Ni particles have a strong metal particle size effect and lead to its better catalytic activity.展开更多
A series of Cu-MgO catalysts was prepared via a urea-nitrate combustion method, and their catalytic per-formance was examined in the vapor phase hydrogenation of furfural. Characterization results showed that the amou...A series of Cu-MgO catalysts was prepared via a urea-nitrate combustion method, and their catalytic per-formance was examined in the vapor phase hydrogenation of furfural. Characterization results showed that the amount of urea had important effects on the surface area, Cu dispersion and crystallite size of the catalysts. The Cu-MgO catalyst with a Cu loading of 12.1%（mass fraction） showed higher furfural conversion than the catalyst prepared by coprecipitation. The high activity was attributed to the higher dispersion of Cu on the catalyst surface. These results suggest that the combustion method is an efficient and simple route for the preparation of high activity Cu-MgO catalysts for furfural hydrogenation.展开更多
MgO-modified Ni/Al2O3 catalysts with different Ni loadings were prepared and employed in dry reforming of methane （DRM）. The effect of Ni loadings on the activity and coke formation of Ni/MgO-A1203 catalysts were in...MgO-modified Ni/Al2O3 catalysts with different Ni loadings were prepared and employed in dry reforming of methane （DRM）. The effect of Ni loadings on the activity and coke formation of Ni/MgO-A1203 catalysts were investigated. The synthesized catalysts were characterized by XRD, N2 adsorption-desorption, SEM, TPO and TPR techniques. The obtained results showed that increasing nickel loading decreased the BET surface area and increased the catalytic activity and amount of deposited carbon. In addition, the effect of gas hourly space velocity （GHSV） and feed ratio were studied.展开更多
Nano ZrO2 and MgO-ZrO2 were prepared by a self-assembly route and were employed as the support for Ni catalysts used in hydrogen production from glycerol reforming in supercritical water （SCW）. The reforming experim...Nano ZrO2 and MgO-ZrO2 were prepared by a self-assembly route and were employed as the support for Ni catalysts used in hydrogen production from glycerol reforming in supercritical water （SCW）. The reforming experiments were conducted in a tubular fixed-bed flow reactor over a temperature range of 600-800 ℃. The influences of process variables such as temperature, contact time, and water to glycerol ratio on hydrogen yield were investigated and the catalysts were charactered by ICP, BET, XRD and SEM. The results showed that high hydrogen yield was obtained from glycerol by reforming in supercritical water over the Ni/MgO-ZrO2 catalysts in a short contact time. The MgO in the catalyst showed significant promotion effect for hydrogen production likely due to the formation of the alkaline active site. Even when the glycerol feed concentration was up to 45 wt%, glycerol was completely gasified and transfered to the gas products containing hydrogen, carbon dioxide, and methane along with small amounts of carbon monoxide. At a diluted feed concentration of 5 wt%, near theoretical yield of 7 mole of H2/mol of glycerol could be obtained.展开更多
A series of nano-size gold catalysts were prepared by deposition-precipitation method using silica material promoted with different amounts of MgO as the carrier. The influences of MgO addition on the structure and pr...A series of nano-size gold catalysts were prepared by deposition-precipitation method using silica material promoted with different amounts of MgO as the carrier. The influences of MgO addition on the structure and property of the nano-size gold catalysts were characterized by X-ray diffraction （XRD）, transmission electron microscopy （TEM）, O2 temperature-programmed desorption （O2-TPD）, and inductively coupled with plasma atomic emission spectroscopy （ICP-AES） techniques. The total oxidation of CO was chosen as the probe reaction. The results suggest that for the gold catalysts supported on the silica material after MgO modification, the size of the gold particles is pronouncedly reduced, the oxygen mobility is enhanced, and the catalytic activity for low-temperature CO oxidation is greatly improved. The gold catalyst modified by 6 wt% MgO （Mg/SiO2 weight ratio） shows higher CO oxidation activity, over which the temperature of CO total oxidation is lower about 150 K than that over the silica directly supported gold catalyst.展开更多
基金supported by the National Natural Science Foundation of China(No.11075113)the Doctoral R&D Foundation of Yibin University(2010B12)
文摘A new type of Ni/MgO catalyst was prepared using atmospheric high-frequency discharge cold plasma. The influences of conventional method, plasma method, and plasma plus calcination method on the catalytic activity were studied and the CO2 reforming of methane was chosen as the probe reaction. The catalysts were characterized by X-ray diffraction （XRD）, transmission electron microscope （TEM）, X-ray photoelectron spectroscopy, and CO2 temperature-programmed surface reaction techniques. The results suggested that the nickel-based catalyst prepared by plasma plus calcination method possessed a smaller particle size and a higher dispersion of active component, better low-temperature activity and enhanced anti-coking ability. The conversion of CO2 and CH4 was 90.70% and 89.37%, respectively, and the reaction lasted for 36 h without obvious deactivation under 101.325 kPa and 750°C with CO2/CH4 = 1/1.
文摘Sulphur-containing aromatic amines were prepared efficiently in good to excellent yields by reduction of the corresponding sulphur-containing aromatic nitro compounds with hydrazine hydrate in the presence of iron（Ⅲ） oxide-MgO catalyst. The catalyst exhibited high activity and stability for the reduction of sulphur-containing aromatic nitro compounds. The yields of sulphur-containing aromatic amines were up to 91-99 % at 355 K after reduction for 1-4 h over this catalyst.
基金supported by the National Natural Science Foundation of China (No. 20873013)
文摘Pt-CeO2-ZrO2/MgO （Pt-CZ/MgO） catalysts with 0.8 wt% Pt, 3.0 wt% CeO2 and 3.0 wt% ZrO2 were prepared by wet impregnation method. Support MgO was obtained using ion exchange resin method or using commercial MgO. XRD, BET, SEM, TEM, DTA-TG and CO2-TPD were used to characterize the catalysts. CH4-CO2 reforming to synthesis gas （syngas） was performed to test the catalytic behavior of the catalysts. The catalyst Pt-CZ/MgO-IE（D） prepared using ion exchange resin exhibits more regular structure, smaller and more unique particle sizes, and stronger basicity than the catalyst Pt-CZ/MgO prepared from commercial MgO. At 1073 K and atmospheric pressure, Pt-CZ/MgO-IE（D） catalyst has a higher activity and greater stability than Pt-CZ/MgO catalyst for CH4-CO2 reforming reaction at high gas hourly space velocity of 36000 mL/（g.h） with a stoichiometric feed of CH4 and C02. Activity measurement and characterization results demonstrate that modification of the support using ion exchange resin method can promote the surface structural property and stability, therefore enhancing the activity and stability for CH4-CO2 reforming reaction.
文摘Ab initio calculations based on density functional theory have been used to study thedecompsition of N_2O on MgO. The reaction is predicted to occur on O_3c and O_(4c) atoms, but not onO_(5c) atoms, with an activation barrier of 25-27 kcal/mol, in agreement with the experimental valueof 35 kcal/mol. Natural bond orbital analysis shows that the reaction leaves O ad-atoms on thosesurface O anions to form a peroxide-like 'O^2_(2-)' species. The )O-O bond stretching frequency ispredicted to be in the range from 820 cm(-1) to 825 cm(-1).
文摘The structures and catalytic performances of V_2O_5, Mg_3V_2O_8 and V/MgO catalysts have been correlated by means of XRD, FTIR, TPR and flow micro-reactor tests. The postulation about active site has been made. Based on it, better catalysts have been first prepared via grafting and modification with Sb which are better than that via impregnation.
基金Supported by the National Natural Science Foundation of China(U1361202,51276120)
文摘Carbon deposition is sensitive to the metal particle sizes of supported Ni catalysts in CH_4/CO_2 reforming.To explore the reason of this phenomenon,Ni4,Ni8,and Ni12 which re flect the different cluster thicknesses supported on the MgO(100) slabs,have been employed to simulate Ni/MgO catalysts,and the reaction pathways of CH_4/CO_2 reforming on Nix/MgO(100) models are investigated by density functional theory.The reforming mechanisms of CH_4/CO_2 on different Nix/MgO(100) indicate the energy barriers of CH_4 dissociated adsorption,CH dissociation,and C oxidation three factors are all declining with the decrease of the Ni cluster sizes.The Hirshfeld charges analyses of three steps as described above show only Ni atoms in bottom two layers can obtain electrons from the MgO supporters,and the main electron transfer occurs between adsorbed species and their directly contacted Ni atoms.Due to more electron-rich Ni atoms in contact with the MgO supporters,the Ni/MgO catalysts with small Ni particles have a strong metal particle size effect and lead to its better catalytic activity.
文摘A series of Cu-MgO catalysts was prepared via a urea-nitrate combustion method, and their catalytic per-formance was examined in the vapor phase hydrogenation of furfural. Characterization results showed that the amount of urea had important effects on the surface area, Cu dispersion and crystallite size of the catalysts. The Cu-MgO catalyst with a Cu loading of 12.1%（mass fraction） showed higher furfural conversion than the catalyst prepared by coprecipitation. The high activity was attributed to the higher dispersion of Cu on the catalyst surface. These results suggest that the combustion method is an efficient and simple route for the preparation of high activity Cu-MgO catalysts for furfural hydrogenation.
基金supported by the University of Kashan(Grant No.158426/16)
文摘MgO-modified Ni/Al2O3 catalysts with different Ni loadings were prepared and employed in dry reforming of methane （DRM）. The effect of Ni loadings on the activity and coke formation of Ni/MgO-A1203 catalysts were investigated. The synthesized catalysts were characterized by XRD, N2 adsorption-desorption, SEM, TPO and TPR techniques. The obtained results showed that increasing nickel loading decreased the BET surface area and increased the catalytic activity and amount of deposited carbon. In addition, the effect of gas hourly space velocity （GHSV） and feed ratio were studied.
基金supported by the National Natural Science Foundation (21076047 and 21276054)the Natural Science Foundation of Zhongkai University of Agriculture and Engineering (G3100026)
文摘Nano ZrO2 and MgO-ZrO2 were prepared by a self-assembly route and were employed as the support for Ni catalysts used in hydrogen production from glycerol reforming in supercritical water （SCW）. The reforming experiments were conducted in a tubular fixed-bed flow reactor over a temperature range of 600-800 ℃. The influences of process variables such as temperature, contact time, and water to glycerol ratio on hydrogen yield were investigated and the catalysts were charactered by ICP, BET, XRD and SEM. The results showed that high hydrogen yield was obtained from glycerol by reforming in supercritical water over the Ni/MgO-ZrO2 catalysts in a short contact time. The MgO in the catalyst showed significant promotion effect for hydrogen production likely due to the formation of the alkaline active site. Even when the glycerol feed concentration was up to 45 wt%, glycerol was completely gasified and transfered to the gas products containing hydrogen, carbon dioxide, and methane along with small amounts of carbon monoxide. At a diluted feed concentration of 5 wt%, near theoretical yield of 7 mole of H2/mol of glycerol could be obtained.
基金supported by the Youth Fund Project(2002B25)of Sichuan Department of Educationthe Scientific Research Foundation for Doctor from Yibin College of China(2010B12)
文摘A series of nano-size gold catalysts were prepared by deposition-precipitation method using silica material promoted with different amounts of MgO as the carrier. The influences of MgO addition on the structure and property of the nano-size gold catalysts were characterized by X-ray diffraction （XRD）, transmission electron microscopy （TEM）, O2 temperature-programmed desorption （O2-TPD）, and inductively coupled with plasma atomic emission spectroscopy （ICP-AES） techniques. The total oxidation of CO was chosen as the probe reaction. The results suggest that for the gold catalysts supported on the silica material after MgO modification, the size of the gold particles is pronouncedly reduced, the oxygen mobility is enhanced, and the catalytic activity for low-temperature CO oxidation is greatly improved. The gold catalyst modified by 6 wt% MgO （Mg/SiO2 weight ratio） shows higher CO oxidation activity, over which the temperature of CO total oxidation is lower about 150 K than that over the silica directly supported gold catalyst.
