Utilizing lightweight Al alloys in various industrial applications requires achieving precise pressure tightness and leak requirements.Vacuum pressure impregnation(VPI)with thermosetting polymers is commonly used to a...Utilizing lightweight Al alloys in various industrial applications requires achieving precise pressure tightness and leak requirements.Vacuum pressure impregnation(VPI)with thermosetting polymers is commonly used to address leakage defects in die-cast Al alloys.In this study,the efficacy of the VPI technique in sealing alloy parts was investigated using a combination of nondestructive micro X-ray computed tomography(micro XCT)and a standard leak test.The results demonstrate that the commonly used water leak test is insufficient for determining the sealing performance.Instead,micro XCT shows distinct advantages by enabling more comprehensive analysis.It reveals the presence of a low atomic number impregnates sealant within casting defects,which has low grey contrast and allows for visualizing primary leakage paths in 3D.The effective atomic number of impregnated resin is 6.75 and that of Al alloy is 13.69 by dual-energy X-ray CT.This research findings will contribute to enhancing the standard VPI process parameters and the properties of impregnating sealants to improve quality assurance for impregnation in industrial metals.展开更多
INTRODUCTIONThe studies on the quantitative distribution of the conventional elements and their phases in the sediments of the Changjiang Estuary are of great importance to the understanding of the chemical processes ...INTRODUCTIONThe studies on the quantitative distribution of the conventional elements and their phases in the sediments of the Changjiang Estuary are of great importance to the understanding of the chemical processes of ion exchange, absorption, desorption and flocculation in the estuary.展开更多
Due to seasonal climate alterations,the microstructure and permeability of granite residual soil are easily affected by multiple dry-wet cycles.The X-ray micro computed tomography(micro-CT)acted as a nondestructive to...Due to seasonal climate alterations,the microstructure and permeability of granite residual soil are easily affected by multiple dry-wet cycles.The X-ray micro computed tomography(micro-CT)acted as a nondestructive tool for characterizing the microstructure of soil samples exposed to a range of damage levels induced by dry-wet cycles.Subsequently,the variations of pore distribution and permeability due to drywet cycling effects were revealed based on three-dimensional(3D)pore distribution analysis and seepage simulations.According to the results,granite residual soils could be separated into four different components,namely,pores,clay,quartz,and hematite,from micro-CT images.The reconstructed 3D pore models dynamically demonstrated the expanding and connecting patterns of pore structures during drywet cycles.The values of porosity and connectivity are positively correlated with the number of dry-wet cycles,which were expressed by exponential and linear functions,respectively.The pore volume probability distribution curves of granite residual soil coincide with the χ^(2)distribution curve,which verifies the effectiveness of the assumption of χ^(2)distribution probability.The pore volume distribution curves suggest that the pores in soils were divided into four types based on their volumes,i.e.micropores,mesopores,macropores,and cracks.From a quantitative and visual perspective,considerable small pores are gradually transformed into cracks with a large volume and a high connectivity.Under the action of dry-wet cycles,the number of seepage flow streamlines which contribute to water permeation in seepage simulation increases distinctly,as well as the permeability and hydraulic conductivity.The calculated hydraulic conductivity is comparable with measured ones with an acceptable error margin in general,verifying the accuracy of seepage simulations based on micro-CT results.展开更多
This research reports the processing of magnesium matrix composites reinforced with silicon carbide(SiC)and aluminium oxide(Al_(2)O_(3))using powder metallurgy technique through high energy milling.Samples of Mg-SiC a...This research reports the processing of magnesium matrix composites reinforced with silicon carbide(SiC)and aluminium oxide(Al_(2)O_(3))using powder metallurgy technique through high energy milling.Samples of Mg-SiC and Mg-Al_(2)O_(3)composites subjected to high energy ball milling for different vol%of secondary particles 20,30 and 40%of SiC and Al_(2)O_(3)are studied by X-Ray diffraction technique.The rietveld method as implemented in the Fullprof program is applied in order to determine the quantities of the resulting crystalline phases and amorphous phases at each stage of the mechanical treatment.Microstructural examination is carried out using Scanning Electron Microscope(SEM).In addition,crystal structural analysis using appropriate size and strain models is performed in order to handle the distinctive anistrophy that is observed in convinced crystallographic directions for the magnesium composite.The results are furnished in terms of crystalline domains size enlargement of the magnesium composites phases upon prolonged milling duration and discussed in the light of up to date views and theories on crystal growth of nanocrystaline materials.The hardness of the composite samples is calculated by Vickers’s Hardness tester.Further,dry sling wear test and corrosion test are performed for the fabricated composites.Composite with 30%secondary particles incorporated magnesium composites exhibits better wear and corrosion resistance than the other composites.展开更多
The construction of a new beamline,BL10U1,was completed at the Shanghai synchrotron radiation facility in 2020.This multipurpose beamline was designed to provide X-ray scattering techniques such as ultra-small-angle X...The construction of a new beamline,BL10U1,was completed at the Shanghai synchrotron radiation facility in 2020.This multipurpose beamline was designed to provide X-ray scattering techniques such as ultra-small-angle X-ray scattering(USAXS),small-angle X-ray scattering(SAXS),wide-angle X-ray scattering,and microfocus SAXS(μSAXS)for a broad user community.To realize fast time-resolved USAXS experiments,the beamline adopted an in-vacuum undulator with a total length of 1.6 m as the photon source.An in-house cryogenic-cooled double multilayer monochromator was installed to deliver a photon flux of approximately 10^(13) photons/s at a photon energy of 10 keV.The three-year successful operation of this beamline demonstrated that the monochromator operated smoothly,as expected.BL10U1 has three end stations in succession:USAXS end station,μSAXS end station,and end station for industrial applications.The minimum scattering vector q~0.0042 nm^(-1) at 10 keV can be achieved at the USAXS end station equipped with a 28 m-long and 1.8 m-diameter vacuum flight tube.At theμSAXS end station,a beam spot of less than 10×8μm was achieved for micro-SAXS experiments.In contrast,in situ experimental instruments up to 5 m high and 8 m wide can be mounted at the industrial application end station,which offers industrial scientists the opportunity to use their large industrial equipment.BL10U1 opens up a new capability to investigate phenomena such as non-equilibrium and dynamic processes of materials with a wide length scale from angstroms to micrometers with millisecond time resolution.In this paper,we also report beamline design considerations and commissioning results.展开更多
The visualization and data mining of tumor multidimensional information may play a major role in the analysis of the growth,metastasis,and microenvironmental changes of tumors while challenging traditional imaging and...The visualization and data mining of tumor multidimensional information may play a major role in the analysis of the growth,metastasis,and microenvironmental changes of tumors while challenging traditional imaging and data processing techniques.In this study,a general trans-scale and multi-modality measurement method was developed for the quantitative diagnosis of hepatocellular carcinoma(HCC)using a combination of propagation-based phase-contrast computed tomography(PPCT),scanning transmission soft X-ray microscopy(STXM),and Fourier transform infrared micro-spectroscopy(FTIR).Our experimental results reveal the trans-scale micro-morpho-logical HCC pathology and facilitate quantitative data analysis and comprehensive assessment.These results include some visualization features of PPCT-based tissue microenvironments,STXM-based cellular fine structures,and FTIR-based bio-macromolecular spectral characteris-tics during HCC tumor differentiation and proliferation.The proposed method provides multidimensional feature data support for constructing a high-accuracy machine learning algorithm based on a gray-level histogram,gray-gradient co-occurrence matrix,gray-level co-occurrence matrix,and back-propagation neural network model.Multi-dimensional information analysis and diagnosis revealed the morphological pathways of HCC pathological evolution and we explored the relationships between HCC-related feature changes in inflammatory microenviron-ments,cellular metabolism,and the stretching vibration peaks of biomolecules of lipids,proteins,and nucleic acids.Therefore,the proposed methodology has strong potential for the visualization of complex tumors and assessing the risks of tumor differentiation and metastasis.展开更多
Micro porosity in aluminum alloys may contribute to fatigue life degradation, which can largely limit the application of alloys. Therefore, the fatigue life of a commercial 7050-T7451 thick plate and an experimental p...Micro porosity in aluminum alloys may contribute to fatigue life degradation, which can largely limit the application of alloys. Therefore, the fatigue life of a commercial 7050-T7451 thick plate and an experimental plate with different porosities was compared in this study. The X-ray computed tomography(XCT) was utilized to characterize the size, number density and spatial distribution of porosity inside various samples, and the fracture surface of fatigued specimens was compared by using scanning electron microscope(SEM). The results showed that the fatigue cracks prefer to initiate from constituent particles in the commercial alloy. Whereas the micro porosity is the predominant site for crack nucleation and subsequent failure in the experimental one. The presence of micro porosity in experimental7050-T7451 thick plate may reduce the fatigue life by an order of magnitude or more compared with the defect-free alloy. The pores close to sample surface are the main fatigue crack initiation site, among which larger and deeper pore leads to a shorter fatigue life. The crack initiation is also affected by the pore geometry and direction. Besides, the overall porosity inside the bulk can affect the crack propagation during fatigue tests.展开更多
Raffia fibres are made from fibrous branches and leaves of Raffia palm. The membrane on the underside of each individual frond leaf is taken off to create a long thin fiber. They are usually waste materials which caus...Raffia fibres are made from fibrous branches and leaves of Raffia palm. The membrane on the underside of each individual frond leaf is taken off to create a long thin fiber. They are usually waste materials which cause a great environmental degradation. The characterization of Raffia palm fibers/ particles was investigated through X-ray diffractometer (XRD), thermogravimetric analysis (TGA/DTA), Fourier transform infrared spectrometry (FTIR), Scanning electron mi croscope with energy dispersive spectrometer (SEM/EDS) and Atomic force microscope (AFM). The various results obtained are equivalent to those of other agro-waste materials generally used in roofing sheets composites production. Hence, this work shows that Raffia palm fibers/particles can be a useful material for cement mortar composites production which can be used for production of roofing sheets.展开更多
Microcrystalline cellulose (MCC) was pretreated by using ionic liquids (ILs)-water mixtures solvent with solid acid catalysts. Different amount of water was considerate as the main variable. The peak shift of pretreat...Microcrystalline cellulose (MCC) was pretreated by using ionic liquids (ILs)-water mixtures solvent with solid acid catalysts. Different amount of water was considerate as the main variable. The peak shift of pretreated sample was determined by FT-IR related to the water content. The XRD was applied to characterize the change in MCC crystalline structure. Thermal decomposition technique was applied to investigate the thermal stability of pretreated MCC. The result indicated that three state of samples were occurred in pretreated MCC sample which was related the amount of water in ILs mixture system. XRD result suggested that the raw sample was distorted and transformed into a less ordered intermediate structure and the smaller crystallite size in lump state sample was obtained which could lead to lower thermal stability. This study revealed the physical chemicals properties, characteristic of molecular structures in MCC using ILs-water mixtures.展开更多
Two non-destructive analytical techniques (gamma spectrometer and X-ray diffractometer) were employed in the analysis of bauxite and rutile ore and their vicinity soil and control sourced within the Kanam and Wase min...Two non-destructive analytical techniques (gamma spectrometer and X-ray diffractometer) were employed in the analysis of bauxite and rutile ore and their vicinity soil and control sourced within the Kanam and Wase mineral exploration sites. The activity concentrations of natural radionuclides <sup>238</sup>U, <sup>232</sup>Th, and <sup>40</sup>K in the soil samples received from bauxite and rutile mineral mining vicinities revealed high concentrations of <sup>238</sup>U, <sup>232</sup>Th, and <sup>40</sup>K compared to the control soil samples sourced 500 m away from the mineral exploration vicinities. Radiological detriments RLI, AUI, Hin and Hex unveiled values exceeding the radiation standard concentration (>1) for soil. X-ray diffraction characterization of bauxite ore revealed the interlocking minerals of Bauxite (18)%, Albite (11)%, Garnet (15)%, Illite (6)% and Muscovite (43)% in various proportions obtained within the 2θ range (9.18 to 64.4) and a peak value (intensity, cps) of 3400. Pure bauxite percentage in the ore meets metallurgical grade (15 - 25)%. X-ray diffraction of rutile ore revealed the minerals of rutile (40)%, quartz (21.4)%, ilmenite (27)% and garnet (11.8)% found within the 2θ range (27.5 to 35.6) and a peak value intensity of 31.1 - 100.0 cps also meeting the metallurgical grade of 15% - 25%. The major environmental concern associated with the mineral-sands industry is the radiation hazards, pollution of ground-water sources from heavy metals, mineral transport with heavy equipment’s, dredging operations in fragile coastal area and clearing of vegetation.展开更多
网纹红土红色基质和白色网纹的成分和结构差异性影响并控制着工程特性。文章通过扫描电子显微镜(scanning electron microscope,SEM)实验和数字图像处理技术定量研究原状网纹红土的微孔隙特征,进而基于能量色散谱仪(energy dispersive s...网纹红土红色基质和白色网纹的成分和结构差异性影响并控制着工程特性。文章通过扫描电子显微镜(scanning electron microscope,SEM)实验和数字图像处理技术定量研究原状网纹红土的微孔隙特征,进而基于能量色散谱仪(energy dispersive spectrometer,EDS)和X射线衍射仪(X-ray diffractometer,XRD)分析了红色基质和白色网纹的化学成分和黏土矿物构成,以探讨网纹红土微结构和成分与其力学特征的内在联系。研究得出,网纹红土孔隙主要为小于0.5μm2面积的微孔隙,而面积超过50μm2的大孔隙则较少,但红色基质颗粒表面粗糙、棱角分明,主要由绿泥石/蒙脱石混层和伊利石以及少量的绿泥石和高岭石构成,而白色网纹颗粒则较为圆滑,由伊利石/蒙脱石混层和伊利石构成,且红色基质中Fe元素质量分数高于白色网纹,而两者中的Ti元素质量分数稳定。研究结果可为深入分析网纹红土工程特征提供依据。展开更多
文摘Utilizing lightweight Al alloys in various industrial applications requires achieving precise pressure tightness and leak requirements.Vacuum pressure impregnation(VPI)with thermosetting polymers is commonly used to address leakage defects in die-cast Al alloys.In this study,the efficacy of the VPI technique in sealing alloy parts was investigated using a combination of nondestructive micro X-ray computed tomography(micro XCT)and a standard leak test.The results demonstrate that the commonly used water leak test is insufficient for determining the sealing performance.Instead,micro XCT shows distinct advantages by enabling more comprehensive analysis.It reveals the presence of a low atomic number impregnates sealant within casting defects,which has low grey contrast and allows for visualizing primary leakage paths in 3D.The effective atomic number of impregnated resin is 6.75 and that of Al alloy is 13.69 by dual-energy X-ray CT.This research findings will contribute to enhancing the standard VPI process parameters and the properties of impregnating sealants to improve quality assurance for impregnation in industrial metals.
基金The project was supported by the National Natural Science Foundation of China.
文摘INTRODUCTIONThe studies on the quantitative distribution of the conventional elements and their phases in the sediments of the Changjiang Estuary are of great importance to the understanding of the chemical processes of ion exchange, absorption, desorption and flocculation in the estuary.
基金supported by the National Natural Science Foundation of China (Grant Nos. 12102312 and 41372314)State Key Laboratory of Geohazard Prevention and Geoenvironment Protection Open Foundation, Chengdu University of Technology, China (Grant No. SKLGP2021K011)
文摘Due to seasonal climate alterations,the microstructure and permeability of granite residual soil are easily affected by multiple dry-wet cycles.The X-ray micro computed tomography(micro-CT)acted as a nondestructive tool for characterizing the microstructure of soil samples exposed to a range of damage levels induced by dry-wet cycles.Subsequently,the variations of pore distribution and permeability due to drywet cycling effects were revealed based on three-dimensional(3D)pore distribution analysis and seepage simulations.According to the results,granite residual soils could be separated into four different components,namely,pores,clay,quartz,and hematite,from micro-CT images.The reconstructed 3D pore models dynamically demonstrated the expanding and connecting patterns of pore structures during drywet cycles.The values of porosity and connectivity are positively correlated with the number of dry-wet cycles,which were expressed by exponential and linear functions,respectively.The pore volume probability distribution curves of granite residual soil coincide with the χ^(2)distribution curve,which verifies the effectiveness of the assumption of χ^(2)distribution probability.The pore volume distribution curves suggest that the pores in soils were divided into four types based on their volumes,i.e.micropores,mesopores,macropores,and cracks.From a quantitative and visual perspective,considerable small pores are gradually transformed into cracks with a large volume and a high connectivity.Under the action of dry-wet cycles,the number of seepage flow streamlines which contribute to water permeation in seepage simulation increases distinctly,as well as the permeability and hydraulic conductivity.The calculated hydraulic conductivity is comparable with measured ones with an acceptable error margin in general,verifying the accuracy of seepage simulations based on micro-CT results.
文摘This research reports the processing of magnesium matrix composites reinforced with silicon carbide(SiC)and aluminium oxide(Al_(2)O_(3))using powder metallurgy technique through high energy milling.Samples of Mg-SiC and Mg-Al_(2)O_(3)composites subjected to high energy ball milling for different vol%of secondary particles 20,30 and 40%of SiC and Al_(2)O_(3)are studied by X-Ray diffraction technique.The rietveld method as implemented in the Fullprof program is applied in order to determine the quantities of the resulting crystalline phases and amorphous phases at each stage of the mechanical treatment.Microstructural examination is carried out using Scanning Electron Microscope(SEM).In addition,crystal structural analysis using appropriate size and strain models is performed in order to handle the distinctive anistrophy that is observed in convinced crystallographic directions for the magnesium composite.The results are furnished in terms of crystalline domains size enlargement of the magnesium composites phases upon prolonged milling duration and discussed in the light of up to date views and theories on crystal growth of nanocrystaline materials.The hardness of the composite samples is calculated by Vickers’s Hardness tester.Further,dry sling wear test and corrosion test are performed for the fabricated composites.Composite with 30%secondary particles incorporated magnesium composites exhibits better wear and corrosion resistance than the other composites.
基金This work was supported by the National Key R&D Program of China(No.2020YFA0405802)the Shanghai Large Scientific Facilities Center.
文摘The construction of a new beamline,BL10U1,was completed at the Shanghai synchrotron radiation facility in 2020.This multipurpose beamline was designed to provide X-ray scattering techniques such as ultra-small-angle X-ray scattering(USAXS),small-angle X-ray scattering(SAXS),wide-angle X-ray scattering,and microfocus SAXS(μSAXS)for a broad user community.To realize fast time-resolved USAXS experiments,the beamline adopted an in-vacuum undulator with a total length of 1.6 m as the photon source.An in-house cryogenic-cooled double multilayer monochromator was installed to deliver a photon flux of approximately 10^(13) photons/s at a photon energy of 10 keV.The three-year successful operation of this beamline demonstrated that the monochromator operated smoothly,as expected.BL10U1 has three end stations in succession:USAXS end station,μSAXS end station,and end station for industrial applications.The minimum scattering vector q~0.0042 nm^(-1) at 10 keV can be achieved at the USAXS end station equipped with a 28 m-long and 1.8 m-diameter vacuum flight tube.At theμSAXS end station,a beam spot of less than 10×8μm was achieved for micro-SAXS experiments.In contrast,in situ experimental instruments up to 5 m high and 8 m wide can be mounted at the industrial application end station,which offers industrial scientists the opportunity to use their large industrial equipment.BL10U1 opens up a new capability to investigate phenomena such as non-equilibrium and dynamic processes of materials with a wide length scale from angstroms to micrometers with millisecond time resolution.In this paper,we also report beamline design considerations and commissioning results.
基金supported by the Natural Science Foundation of Shandong Province,China(No.ZR2020MA088)Natural Science Foundation of Xinjiang Uygur Autonomous Region,China(No.2019D01C188)+1 种基金National Key Research and Development Program of China(No.2018YFC1200204)National Natural Science Foundation of China(No.12175127).
文摘The visualization and data mining of tumor multidimensional information may play a major role in the analysis of the growth,metastasis,and microenvironmental changes of tumors while challenging traditional imaging and data processing techniques.In this study,a general trans-scale and multi-modality measurement method was developed for the quantitative diagnosis of hepatocellular carcinoma(HCC)using a combination of propagation-based phase-contrast computed tomography(PPCT),scanning transmission soft X-ray microscopy(STXM),and Fourier transform infrared micro-spectroscopy(FTIR).Our experimental results reveal the trans-scale micro-morpho-logical HCC pathology and facilitate quantitative data analysis and comprehensive assessment.These results include some visualization features of PPCT-based tissue microenvironments,STXM-based cellular fine structures,and FTIR-based bio-macromolecular spectral characteris-tics during HCC tumor differentiation and proliferation.The proposed method provides multidimensional feature data support for constructing a high-accuracy machine learning algorithm based on a gray-level histogram,gray-gradient co-occurrence matrix,gray-level co-occurrence matrix,and back-propagation neural network model.Multi-dimensional information analysis and diagnosis revealed the morphological pathways of HCC pathological evolution and we explored the relationships between HCC-related feature changes in inflammatory microenviron-ments,cellular metabolism,and the stretching vibration peaks of biomolecules of lipids,proteins,and nucleic acids.Therefore,the proposed methodology has strong potential for the visualization of complex tumors and assessing the risks of tumor differentiation and metastasis.
基金Project(2019KJ2X08-4) supported by Chinalco Technology Development Project Fund,China。
文摘Micro porosity in aluminum alloys may contribute to fatigue life degradation, which can largely limit the application of alloys. Therefore, the fatigue life of a commercial 7050-T7451 thick plate and an experimental plate with different porosities was compared in this study. The X-ray computed tomography(XCT) was utilized to characterize the size, number density and spatial distribution of porosity inside various samples, and the fracture surface of fatigued specimens was compared by using scanning electron microscope(SEM). The results showed that the fatigue cracks prefer to initiate from constituent particles in the commercial alloy. Whereas the micro porosity is the predominant site for crack nucleation and subsequent failure in the experimental one. The presence of micro porosity in experimental7050-T7451 thick plate may reduce the fatigue life by an order of magnitude or more compared with the defect-free alloy. The pores close to sample surface are the main fatigue crack initiation site, among which larger and deeper pore leads to a shorter fatigue life. The crack initiation is also affected by the pore geometry and direction. Besides, the overall porosity inside the bulk can affect the crack propagation during fatigue tests.
文摘Raffia fibres are made from fibrous branches and leaves of Raffia palm. The membrane on the underside of each individual frond leaf is taken off to create a long thin fiber. They are usually waste materials which cause a great environmental degradation. The characterization of Raffia palm fibers/ particles was investigated through X-ray diffractometer (XRD), thermogravimetric analysis (TGA/DTA), Fourier transform infrared spectrometry (FTIR), Scanning electron mi croscope with energy dispersive spectrometer (SEM/EDS) and Atomic force microscope (AFM). The various results obtained are equivalent to those of other agro-waste materials generally used in roofing sheets composites production. Hence, this work shows that Raffia palm fibers/particles can be a useful material for cement mortar composites production which can be used for production of roofing sheets.
文摘Microcrystalline cellulose (MCC) was pretreated by using ionic liquids (ILs)-water mixtures solvent with solid acid catalysts. Different amount of water was considerate as the main variable. The peak shift of pretreated sample was determined by FT-IR related to the water content. The XRD was applied to characterize the change in MCC crystalline structure. Thermal decomposition technique was applied to investigate the thermal stability of pretreated MCC. The result indicated that three state of samples were occurred in pretreated MCC sample which was related the amount of water in ILs mixture system. XRD result suggested that the raw sample was distorted and transformed into a less ordered intermediate structure and the smaller crystallite size in lump state sample was obtained which could lead to lower thermal stability. This study revealed the physical chemicals properties, characteristic of molecular structures in MCC using ILs-water mixtures.
文摘Two non-destructive analytical techniques (gamma spectrometer and X-ray diffractometer) were employed in the analysis of bauxite and rutile ore and their vicinity soil and control sourced within the Kanam and Wase mineral exploration sites. The activity concentrations of natural radionuclides <sup>238</sup>U, <sup>232</sup>Th, and <sup>40</sup>K in the soil samples received from bauxite and rutile mineral mining vicinities revealed high concentrations of <sup>238</sup>U, <sup>232</sup>Th, and <sup>40</sup>K compared to the control soil samples sourced 500 m away from the mineral exploration vicinities. Radiological detriments RLI, AUI, Hin and Hex unveiled values exceeding the radiation standard concentration (>1) for soil. X-ray diffraction characterization of bauxite ore revealed the interlocking minerals of Bauxite (18)%, Albite (11)%, Garnet (15)%, Illite (6)% and Muscovite (43)% in various proportions obtained within the 2θ range (9.18 to 64.4) and a peak value (intensity, cps) of 3400. Pure bauxite percentage in the ore meets metallurgical grade (15 - 25)%. X-ray diffraction of rutile ore revealed the minerals of rutile (40)%, quartz (21.4)%, ilmenite (27)% and garnet (11.8)% found within the 2θ range (27.5 to 35.6) and a peak value intensity of 31.1 - 100.0 cps also meeting the metallurgical grade of 15% - 25%. The major environmental concern associated with the mineral-sands industry is the radiation hazards, pollution of ground-water sources from heavy metals, mineral transport with heavy equipment’s, dredging operations in fragile coastal area and clearing of vegetation.
