WC-Co is used widely in die and mold industries due to its unique combination of hardness, strength and wear-resistance. For machining difficult-to-cut materials, such as tungsten carbide, micro-electrical discharge m...WC-Co is used widely in die and mold industries due to its unique combination of hardness, strength and wear-resistance. For machining difficult-to-cut materials, such as tungsten carbide, micro-electrical discharge machining(EDM) is one of the most effective methods for making holes because the hardness is not a dominant parameter in EDM. This paper describes the characteristics of the discharge conditions for micro-hole EDM of tungsten carbide with a WC grain size of 0.5 μm and Co content of 12%. The EDM process was conducted by varying the condenser and resistance values. A R-C discharge EDM device using arc erosion for micro-hole machining was suggested. Furthermore, the characteristics of the developed micro-EDM were analyzed in terms of the electro-optical observation using an oscilloscope and field emission scanning electron microscope.展开更多
Machining of micro holes with micro electro- chemical machining （micro ECM） process has been carried out with an indigenously developed set up. This paper describes relevant problems and solutions for the circular m...Machining of micro holes with micro electro- chemical machining （micro ECM） process has been carried out with an indigenously developed set up. This paper describes relevant problems and solutions for the circular micro holes machining process on 304 stainless steel sheets with 60 μm thickness using high speed steel cylindrical tool of diameter 500 ~tm and using dilute I-I2SO4 as elec- trolyte. The taper angle variation of the machined hole is analyzed and reported for different experimental setting parameters. The minimum value of the taper angle of machined holes is achieved at the parameter setting of 0.4 mol/L H2504, 700 kHz, 600 ns and 21 V, for stainless steel sheets and HSS tool.展开更多
Silicon carbide (SiC) is highly wear resistant with good mechanical properties, including high temperature strength, excellent chemical resistance, and high thermal conductivity and thermal shock resistance. SiC molds...Silicon carbide (SiC) is highly wear resistant with good mechanical properties, including high temperature strength, excellent chemical resistance, and high thermal conductivity and thermal shock resistance. SiC molds, which can be produced with diverse microstructural features, are now widely used in glass molding owing to their excellent characteristics, and also have potential applicability in IT industries. SiC molds are traditionally fabricated by silicon micromachining or dicing. The fabrication cost of silicon micromachining is very high, however, because several expensive masks are needed. Furthermore, the fabrication time is very long. Meanwhile, it is difficult to make micro-patterned molds with arbitrary shapes using dicing saws. Abrasive water jet (AWJ) is widely applied to cut and drill very brittle, soft and fibrous materials. It offers high energy density, the absence of a heat affected zone(HAZ), high performance, and an environment friendly process. In spite of these advantages, micro-hole drilling via conventional AWJ processing suffers from notable shortcomings. We proposed a new abrasive supplying method of AWJ. The proposed method reduces frosting phenomena, and provides micro-machining of AWJ. The characteristics of a hole machined was investigated by the proposed AWJ process according to the ratio of water and abrasives. With the optimal experimental conditions, 3×3 array SiC molds with the diameter of 700 μm and depth of 900 μm were successfully manufactured.展开更多
A novel micro-hole electrode was fabricated to investigate the electron transfer reaction at the interface between two immiscible electrolyte solutions (ITIES). The electron transfer reaction between ferro/ferricyani...A novel micro-hole electrode was fabricated to investigate the electron transfer reaction at the interface between two immiscible electrolyte solutions (ITIES). The electron transfer reaction between ferro/ferricyanide in aqueous phase (W) and ferrocene in 1, 2-dichloroethane (O) phase was studied as a test experiment. The results showed that the diffusion coefficient obtained from the micro-hole electrode was consistent with that obtained at macro-interface. Due to its simplicity and the very small IR drop it will be a useful tool for the study of ITIES systems.展开更多
The quality of a via hole on a multilayer stack of Low Temperature Co-fired Ceramic (LTCC) tape is of utmost importance to its functionality. This paper investigates a substitute for the commonly used circular shape h...The quality of a via hole on a multilayer stack of Low Temperature Co-fired Ceramic (LTCC) tape is of utmost importance to its functionality. This paper investigates a substitute for the commonly used circular shape hole to a more complex one and its implications when different parameters such as sheet thickness, punch speed, travel distance and tool clearance are?changed. Fabrication of the punch tools and the punching process is carried out at the same machine, ensuring alignment. Two types of non-circular shape are chosen to carry out the experiment. Pre-sintered complex shape hole measurements show that while punch conditions such as speed and tool gap have?little effect on the size, sheet thickness and travel depth play a vital role in the overall dimension. Albeit having only a slight effect on the size, those parameters are significant in other aspects of hole quality. Post-sintering investigation is also observed and discussed.展开更多
Micro electro discharge machining (micro EDM) is a feasible way tomanufacture micro structures and has potential application in advanced industrial fields. For therealization of micro EDM, it is necessary to pay caref...Micro electro discharge machining (micro EDM) is a feasible way tomanufacture micro structures and has potential application in advanced industrial fields. For therealization of micro EDM, it is necessary to pay careful attention to its equipment design and thedevelopment of process techniques. The present status of research and development of micro EDMequipment and process techniques is overviewed. A micro electro discharge machine incorporated withan inchworm type of micro feed mechanism is introduced, and a micro electro discharge machine fordrilling micro holes suitable to industrial use is also introduced. Some of the machiningexperiments carried out on the micro EDM prototypes are shown and the feasibility of the micro EDMtechnology to practical use is discussed.展开更多
基金supported by a Grant-in-aid for the National Core Research Center Program from MOST and KOSEF, Korea (No.R15-2006-022-01001-0)partly supported by Pusan National University Research Grand,2008
文摘WC-Co is used widely in die and mold industries due to its unique combination of hardness, strength and wear-resistance. For machining difficult-to-cut materials, such as tungsten carbide, micro-electrical discharge machining(EDM) is one of the most effective methods for making holes because the hardness is not a dominant parameter in EDM. This paper describes the characteristics of the discharge conditions for micro-hole EDM of tungsten carbide with a WC grain size of 0.5 μm and Co content of 12%. The EDM process was conducted by varying the condenser and resistance values. A R-C discharge EDM device using arc erosion for micro-hole machining was suggested. Furthermore, the characteristics of the developed micro-EDM were analyzed in terms of the electro-optical observation using an oscilloscope and field emission scanning electron microscope.
文摘Machining of micro holes with micro electro- chemical machining （micro ECM） process has been carried out with an indigenously developed set up. This paper describes relevant problems and solutions for the circular micro holes machining process on 304 stainless steel sheets with 60 μm thickness using high speed steel cylindrical tool of diameter 500 ~tm and using dilute I-I2SO4 as elec- trolyte. The taper angle variation of the machined hole is analyzed and reported for different experimental setting parameters. The minimum value of the taper angle of machined holes is achieved at the parameter setting of 0.4 mol/L H2504, 700 kHz, 600 ns and 21 V, for stainless steel sheets and HSS tool.
基金supported by a grant-in-aid for the National Core Research Center Program from the Ministry of Education Science & Technologythe Korea Science & Engineering Foundation (No.R15-2006-022-01001)
文摘Silicon carbide (SiC) is highly wear resistant with good mechanical properties, including high temperature strength, excellent chemical resistance, and high thermal conductivity and thermal shock resistance. SiC molds, which can be produced with diverse microstructural features, are now widely used in glass molding owing to their excellent characteristics, and also have potential applicability in IT industries. SiC molds are traditionally fabricated by silicon micromachining or dicing. The fabrication cost of silicon micromachining is very high, however, because several expensive masks are needed. Furthermore, the fabrication time is very long. Meanwhile, it is difficult to make micro-patterned molds with arbitrary shapes using dicing saws. Abrasive water jet (AWJ) is widely applied to cut and drill very brittle, soft and fibrous materials. It offers high energy density, the absence of a heat affected zone(HAZ), high performance, and an environment friendly process. In spite of these advantages, micro-hole drilling via conventional AWJ processing suffers from notable shortcomings. We proposed a new abrasive supplying method of AWJ. The proposed method reduces frosting phenomena, and provides micro-machining of AWJ. The characteristics of a hole machined was investigated by the proposed AWJ process according to the ratio of water and abrasives. With the optimal experimental conditions, 3×3 array SiC molds with the diameter of 700 μm and depth of 900 μm were successfully manufactured.
文摘A novel micro-hole electrode was fabricated to investigate the electron transfer reaction at the interface between two immiscible electrolyte solutions (ITIES). The electron transfer reaction between ferro/ferricyanide in aqueous phase (W) and ferrocene in 1, 2-dichloroethane (O) phase was studied as a test experiment. The results showed that the diffusion coefficient obtained from the micro-hole electrode was consistent with that obtained at macro-interface. Due to its simplicity and the very small IR drop it will be a useful tool for the study of ITIES systems.
文摘The quality of a via hole on a multilayer stack of Low Temperature Co-fired Ceramic (LTCC) tape is of utmost importance to its functionality. This paper investigates a substitute for the commonly used circular shape hole to a more complex one and its implications when different parameters such as sheet thickness, punch speed, travel distance and tool clearance are?changed. Fabrication of the punch tools and the punching process is carried out at the same machine, ensuring alignment. Two types of non-circular shape are chosen to carry out the experiment. Pre-sintered complex shape hole measurements show that while punch conditions such as speed and tool gap have?little effect on the size, sheet thickness and travel depth play a vital role in the overall dimension. Albeit having only a slight effect on the size, those parameters are significant in other aspects of hole quality. Post-sintering investigation is also observed and discussed.
文摘Micro electro discharge machining (micro EDM) is a feasible way tomanufacture micro structures and has potential application in advanced industrial fields. For therealization of micro EDM, it is necessary to pay careful attention to its equipment design and thedevelopment of process techniques. The present status of research and development of micro EDMequipment and process techniques is overviewed. A micro electro discharge machine incorporated withan inchworm type of micro feed mechanism is introduced, and a micro electro discharge machine fordrilling micro holes suitable to industrial use is also introduced. Some of the machiningexperiments carried out on the micro EDM prototypes are shown and the feasibility of the micro EDMtechnology to practical use is discussed.
