MICRO TEST1自动血沉仪性能评价及生物参考区间的建立

目的探讨MICRO TEST1自动红细胞沉降率(下称血沉)仪检测血沉的可靠性及建立该方法健康成人生物参考区间。方法随机抽取门诊患者90例,分别应用MICRO TEST1自动血沉仪和1993年国际血液学标准化委员会(ICSH)推荐的血沉测定标准方法(即魏氏法)同时检测血沉,对数据进行统计学分析与比较;应用MICRO TEST1自动血沉仪对男性321例、女性311例健康体检者测定血沉,统计该方法生物参考区间。结果MICRO TEST1自动血沉仪测定结果与魏氏法比较差异无统计学意义(P>0.05),两种方法的相关性良好(r=0.974;Y=1.015x-0.354);该方法生物参考区间第95%百分位数点:男为16.0mm/h、女为22.0mm/h,两组差异有统计学意义。结论MICROTEST1自动血沉仪是一种检测血沉快速、准确、可靠的新方法,但必须与参考方法或标准方法进行严格比对,同时应建立方法的生物参考区间。

ISOLATION DESIGN AND SIMULATIONAL EXPERIMENT OF NANOMETER MICRO MOVEMENT TEST-BED

The relation of mass, stiffness and rate of damping is obtained by using the mechanical analysis of the obstructive vibration system of two dimensions for the design of the obstructive vibration system of more freedom and the micro vibration test bed. The result of stimulational experiment indicates that the isolation of vibration of this system is satisfactory. The design method of vibration can be used as the reference to ultra precision machine tool, super micro orientation machanism and so on.

Vibration test of micro machined gyroscope based on high speed photography and SURF

Based on three kinds of dynamic test of MEMS, a dynamic system for the vibration test of micro machined gyroscope based on high speed photography is introduced. Firstly, the architecture of the system hardware is introduced. Secondly, the image tracking performance is compared by the test using the template matching algorithm, the mean shift algorithm and the SURF algorithm. The vibration curve shows that high speed photograph combined with SURF algorithm is faster, more ac- curate, and more suitable for the vibration test of micro machined gyroscope. After the frequency a- nalysis and related interpolation, more characteristics of micro gyroscope can be obtained.

Mechanical Characterization of Electroplated Ni Films by Micro-tensile Testing

Mechanical properties of structural materials are particularly important for design, performance realization and reliability analysis of microelectromechanical systems （MEMS）. Furthermore, accurate database of mechanical properties at the micro scale can provide indispensable reference for establishing MEMS standard. Electroplated nickel film is one of the most favored structural materials used in MEMS, thus its mechanical properties has been studied for many years. However, the measured values show large scatter in Yotmg＇s modulus of nickel film. Young＇s modulus and yield stress of electroplated nickel film are measured by using a micro-tensile testing instrument. The tensile load applied on the specimen is measured by a load cell with accuracy 0.25 mN directly, without additional friction. Through measuring the axial stiffness coefficient of the tensile instnunent in situ, the tensile strain of the specimen is obtained by using two-serial spring model. The electroplated nickel films were fabricated from sulfarnate baths, and the gauge section is 500μm long and 10μm wide nominally, and thickness range between 25 μm and 50μm. The obtained Young＇s modulus from tensile testing is 83＋6 GPa for nickel specimens electroplated at current density of 20 mA/cm2 and it increases to 124＋5 GPa as current density is decreased to 10 mA/cm2. The phenomena are interpreted in terms of porosity of microstructure. The higher current density produced rnicrostucture with low density and high volume fraction of pores, and the microstructure of high porosity corresponds to a lower modulus. The measured values of Young＇s modulus are consistent with those of calculated from the exponential empirical formula between Young＇s modulus and porosity. The micro-tensile testing instrument can also be used for mechanical measurement of other MEMS films.

Elastic modulus of claystone evaluated by nano-/micro-indentation tests and meso-compression tests

Toarcian claystone such as that of the Callovo-Oxfordian is a qualified multiphase material. The claystone samples tested in this study are composed of four main mineral phases: silicates(clay minerals, quartz,feldspars, micas)(z86%), sulphides(pyrite)(z3%), carbonates(calcite, dolomite)(z10%) and organic kerogen(z1%). Three sets of measurements of the modulus of deformability were compared as determined in(i) nanoindentation tests with a constant indentation depth of 2 mm,(ii) micro-indentation tests with a constant indentation depth of 20 mm, and(iii) meso-compression tests with a constant displacement of 200 mm. These three experimental methods have already been validated in earlier studies. The main objective of this study is to demonstrate the influence of the scaling effect on the modulus of deformability of the material. Different frequency distributions of the modulus of deformability were obtained at the different sample scales:(i) in nano-indentation tests, the distribution was spread between 15 GPa and 90 GPa and contained one peak at34 GPa and another at 51 GPa;(ii) in the micro-indentation tests, the distribution was spread between 25 GPa and 60 GPa and displayed peaks at 26 GPa and 37 GPa; and(iii) in the meso-compression tests, a narrow frequency distribution was obtained, ranging from 25 GPa to 50 GPa and with a maximum at around 35 GPa.

Salt spray corrosion test of micro-plasma oxidation ceramic coatings on Ti alloy

Ceramic coatings were prepared on Ti-6Al-4V alloy in NaAlO2 solution by micro-plasma oxidation （MPO）. The salt spray tests of the coated samples and the substrates were carded out in a salt spray test machine. The phase composition and surface morphology of the coatings were investigated by XRD and SEAM. Severe corrosion occurred on the substrate surface, while there were no obvious corrosion phenomena on the coated samples. The coatings were composed of Al2TiO5 and a little α-Al2O3 and mille TiO2, and the salt spray test did not change the composition of the coatings. The weight loss rate of the coatings decreased with increasing MPO time because of the increase in density and thickness of the coatings. The surface morphology of the coatings was influenced by salt spray corrosion test. Among the coated samples, the coating prepared for 2 h has the best corrosion resistance under salt spray test.

Comparison of mechanical properties in welded joint for CO_2 arc welding by using the micro－shear test and impact test

A micro shear testing method which can suit to measure the mechanical properties of heterogeneous materials is introduced, and the properties in each zone of welded joint for CO2 arc welding can be evaluated by using this method in this paper. Moreover, these results are compared with those results of Charpy V-notch impact test and their correlation is discussed.

Measurement of Ca^(2+) Flow in Cochlear Cells Using Non-Invasive Micro-Test Technique

Objective To test Calcium ion(Ca2+) flow at the head and end of outer hair cells(OHCs) in resting state and in response to Nimodipine treatment.Methods Non-invasive micro-test techniques were used to study Ca2+ in isolated OHCs in adult guinea pigs.Results Four types of Ca2+ transport were identified in OHCs on basilar membrane tissue fragments:influx at the head of with efflux at the bottom(type 1):efflux at the head of OHCs with influx at the bottom(type 2);influx at the both head and bottom(type 3);and efflux at the both head and bottom(type 4).However,only type 1 and type 3 of Ca2+ ion transport were detected in the cochlea.We propose that Ca2+ ion transport exists in adult guinea pig cochlear OHCs in resting state and is variable.Ca2 + flow in OHC can be inhibited by Nimodipine in resting state.

Micro-Doppler effect testing technique for attitude of projectile in space flight

To measure projectile attitude in space flight, based on continuous wave （CW） radar, a new micro-Doppler effect testing technique is developed in this paper. It also establishes radar testing model for attitude of flying projectile and resolve micro-Doppler effect of projectile motion attitude. By distinguishing and geting attitude parameters such as micro-motion period, this technique can in- tuitively estimate the flight stability of projectile, and the validity of this technique is proved accord- ing to flight tests.

Experimental Tests on a Pre-Heated Combustion Chamber for Ultra Micro Gas Turbine Device: Air/Fuel Ratio Evaluation

Current portable power generators are mainly based on internal combustion engine since they present higher values of efficiency comparing to other engines;the main reason why internal combustion engine is not convenient for micro power generation (5 - 30 kW) is because of their heaviness. Micro and ultra micro gas turbine devices, based on a micro compressor and a micro turbine installed on the same shaft, are more suitable for this scope for several reasons. Micro turbine systems have many advantages over reciprocating engine generators, such as higher power density (with respect to size and weight), extremely low emissions and few, or just one, moving part. Those designed with foil bearings and air-cooling operate without oil, coolants or other hazardous materials. Micro turbines also have the advantage of having the majority of their waste heat contained in their relatively high temperature exhaust. Micro turbines offer several potential advantages compared to other technologies for small-scale power generation, including: a small number of moving parts, compact size, lightweight, greater efficiency, lower emissions, lower electricity costs, and opportunities to utilize waste fuels. The object of this study is the experimental tests on a stand-alone gas turbine device with a pre-heated combustion chamber (CC), to validate the fuel consumption reduction, compared to an actual and commercial device, used on air models.

Assessing efficacy of standard impregnation techniques on die-cast aluminum alloys using X-ray micro-CT

Utilizing lightweight Al alloys in various industrial applications requires achieving precise pressure tightness and leak requirements.Vacuum pressure impregnation(VPI)with thermosetting polymers is commonly used to address leakage defects in die-cast Al alloys.In this study,the efficacy of the VPI technique in sealing alloy parts was investigated using a combination of nondestructive micro X-ray computed tomography(micro XCT)and a standard leak test.The results demonstrate that the commonly used water leak test is insufficient for determining the sealing performance.Instead,micro XCT shows distinct advantages by enabling more comprehensive analysis.It reveals the presence of a low atomic number impregnates sealant within casting defects,which has low grey contrast and allows for visualizing primary leakage paths in 3D.The effective atomic number of impregnated resin is 6.75 and that of Al alloy is 13.69 by dual-energy X-ray CT.This research findings will contribute to enhancing the standard VPI process parameters and the properties of impregnating sealants to improve quality assurance for impregnation in industrial metals.

China,America Have Coo[erated in Micro Biological Production Test

Ｃｈｉｎａ，ＡｍｅｒｉｃａＨａｖｅＣｏｏｐｅｒａｔｅｄｉｎＭｉｃｒｏｂｉｏｌｏｇｉｃａｌＰｒｏｄｕｃｔｉｏｎＴｅｓｔＨｏｕＦｕＴｈｅｍｉｃｒｏｂｉｏｌｏｇｉｃａｌｐｒｏｄｕｃｔｉｏｎｔｅｃｈｎｏｌｏｇｙｈａｓｂｅｅｎｉｎｔｒｏｄｕｃｅｄｆｒｏｍｔｈｅ...

微磁检测技术在Cr12MoV钢和3Cr13钢屈服/抗拉强度检测中的应用

利用微磁无损检测方法对Cr12MoV钢和3Cr13钢的屈服强度(R_(p0.2))和抗拉强度(R_(m))进行无损定量预测。首先,采用先淬火后回火的工艺改变材料的拉伸力学性能,得到不同屈服/抗拉强度的拉伸试样;其次,对2种材料先后进行微磁特征参量测试和屈服/抗拉强度的测定;然后,分别利用格拉布斯(Grabbs)准则和ReliefF特征筛选方法,剔除系统误差并得到对强度指标敏感的微磁特征参量;最后,通过神经网络模型寻优,构建BP神经网络预测模型,实现Cr12MoV钢和3Cr13钢屈服强度和抗拉强度定量预测。研究结果表明:微磁检测方法可以对Cr12MoV钢和3Cr13钢屈服强度和抗拉强度进行无损定量预测,模型得到的屈服强度和抗拉强度预测平均误差分别小于3%和5%。提出的研究方法和结论可为铁磁性材料屈服强度和抗拉强度的微磁无损检测提供参考。

Model Identification of a Micro Air Vehicle

This paper is focused on the model identification of a Micro Air Vehicle （MAV） in straight steady flight condition. The identification is based on input-output data collected from flight tests using both frequency and time dorrtain techniques. The vehicle is an in-house 40 cm wingspan airplane. Because of the complex coupled, multivariable and nonlinear dynamics of the aircraft, linear SISO structures for both the lateral and longitudinal models around a reference state were derived. The aim of the identification is to provide models that can be used in future development of control techniques for the MAV.

Fractal characteristics of cracks and fragments generated in unloading rockburst tests

True triaxial rockburst experiments with four different unloading rates were performed on four prism specimens of granite sampled from Beishan, China. The damage evolution in the rockburst test was investigated from two aspects including fracture surface crack and fragment characteristics. The scanning electron microscopy was used to observe the micro crack information on fragment surface. Combing binarization and box counting dimensions, the fractal dimensions of cracks were obtained. Meanwhile,the fragments were collected and a sieving experiment was conducted. We weighed the fragments qualities, counted the amount of fragments and measured the fragments length, width and thickness.Utilizing four methods to calculate damage fractal dimensions of fragments, the trend of fractal value changing with unloading rates can be roughly described. It can be concluded from these experiments that the fractal dimension either for crack or for fragment holds a decreasing trend with the decreasing unloading rate, indicating a reduction of damage level.

A MICRO-MECHANICAL MODEL OF KNITTED FABRIC AND ITS APPLICATION TO THE ANALYSIS OF BUCKLING UNDER TENSION IN WALE DIRECTION:MICRO-MECHANICAL MODEL

The typical micro-knitting structure of knitted fabric,which makes it very different from woven fabric,is described.The tensile tests of knitted fabric are reported.The deformations of the micro-knitting structures are carefully studied.The study indicates that when a knitted fabric sheet is subjected to a tension along w-direction an extra compressive stress field inside loop in c-direction is induced.The extra stress field is also determined through analysis.Finally,a micro-mechanical model of knitted fabric is proposed.This work paves the way for the simulations of buckling modes of a knitted fabric sheet as are observed in experiments.

Control system for dynamic testing platform of asymmetrical pitch mechanism

A novel asymmetrical pitch system for rotary wing is presented. The pitch control characteristics are studied and analyzed. Because elastic linkage is a key part in whole asymmetrical pitch system, in order to obtain the variation of the elastic linkage deformation, an experimental platform mainly based on the device of micro aerial vehicles （MAVs） and a new control system mounted on TMS320LF2407 are designed. This control system has its compacted configuration and reliability. Finally, using this system to control the MAV for simulating the flying forward, experimental results show the MAV＇s flight attitude can he controlled based on the variation of the elastic linkage.

Assessment of Domestic Water Sources Safety: Application of the Micro Biological Survey Method and Microbiological Profile of the Contaminating Bacteria

Water is essential for human life and it’s expected to be clean and safe. In Cameroon, government efforts to improve access to drinking water are mitigated. Many households are suffering from chronic water shortages leading to the majority of people using doubtful water sources. This study was carried out in accordance with guidelines produced by the STARBIOS2-EU funded project on Responsible Research and Innovation and aimed to assess the microbiological quality of water samples collected from domestic water sources in 3 divisions of the West region of Cameroon. 22 water samples from well water, stream, water pump and river were aseptically collected. At each sampling point, 50 mL of sample was taken aseptically and immediately transported to the laboratory for analysis. The detection of Coliforms bacteria was done using Micro Biological Survey (MBS) method. 1 mL of each sample was inoculated in the Coliforms MBS (Coli MBS) vial initially rehydrated with 10 mL of sterile distilled water. The Coli MBS vials were closed, shaken for homogenization, and then incubated at 37°C. From the initial red color of the Coli MBS vials, changes in color to yellow of the reaction vials were monitored at three different time intervals (12 h, 19 h and 24 h), corresponding to three levels of bacterial concentration. All positives samples on MBS method were selected to determine the presence of E. coli Loop full broths of Coli MBS vials were taken;streaked into the eosin methylene blue (EMB) agar plate and incubated at 37°C for 24 hours. E. coli was confirmed by observing green metallic sheen on EMB agar plate. The biochemical indole, methyl red, Voges-Proskauer and citrate (IMViC) test was performed to determine the complete microbiological profile of the water samples. Almost all the water samples were contaminated with Total Coliforms (TC). A high concentration of TC (>103 CFU/mL) was found in 8 samples (36.4%), a medium concentration (10 < x < 103 CFU/mL) was observed in 10 samples (45.5%) and 2 samples (9.1%) were low concentrated (1 < x < 10 CFU/mL). 8 samples were positive for the presence of E. coli by observing the green metallic sheen on EMB agar plates. The IMViC test confirmed the presences of 5 bacteria species: Enterobacter spp., Klebsiella spp., E. coli spp., Salmonella spp. and Shigella spp. We recommend integrating sanitary assessment in the design and implementation of water supply projects. Regular water purification using proper methods and maintenances of the water point. Regular microbiological quality assessment of water intended for human consumption should be planned and carried out.

Health condition monitoring with multiple physical signals in tensile test for double-material friction welding

The manifold physical signals including micro resistance,infrared thermal signal and acoustic emission signal in the tensile test for double-material friction welding normative samples were monitored and collected dynamically by TH2512 micro resistance measuring apparatus,flir infrared thermal camera and acoustic emission equipment which possesses 18 bit PCI-2 data acquisition board.Applied acoustic emission and thermal infrared NDT(non-destructive testing) means were used to verify the feasibility of using resistance method and to monitor dynamic damage of the samples.The research of the dynamic monitoring system was carried out with multi-information fusion including resistance,infrared and acoustic emission.The results show that the resistance signal,infrared signal and acoustic emission signal collected synchronously in the injury process of samples have a good mapping.Electrical,thermal and acoustic signals can more accurately capture initiation and development of micro-defects in the sample.Using dynamic micro-resistance method to monitor damage is possible.The method of multi-information fusion monitoring damage possesses higher reliability,which makes the establishing of health condition diagnosing and early warning platform with multiple physical information monitoring possible.

Balanced Fertilizer Use through Soil Testing Leads to Higher Yields and Nutrient Contents of Maize Grains

Fertilizers use can be optimized through soil testing and leaf analysis. This paper deals with using soil analysis as a base for fertilizer use in maize. A field experiment was carried out in two summer seasons of 2013 and 2014 with maize (triple hybrid) in Oraby Village, Mariut sector, Alexandria, Egypt. Soil testing shows that soil was clay loam, with high Na and CaCO3 contents with high pH, low organic matter, medium P and K and low micronutrient contents (Fe, Zn, Mn and Cu), seven treatments were designed. The most promising treatment was when P and K were increased and micronutrients were added based on soil testing. This treatment resulted in the highest yield with better grain contents of protein and nutrients which indicated that soil-test based on fertilizer use was superior. Soil analysis at the end of the experiment showed higher P and K contents. This approach could be adopted for regions with similar soil conditions in other parts of the world.