ISOLATION DESIGN AND SIMULATIONAL EXPERIMENT OF NANOMETER MICRO MOVEMENT TEST-BED

The relation of mass, stiffness and rate of damping is obtained by using the mechanical analysis of the obstructive vibration system of two dimensions for the design of the obstructive vibration system of more freedom and the micro vibration test bed. The result of stimulational experiment indicates that the isolation of vibration of this system is satisfactory. The design method of vibration can be used as the reference to ultra precision machine tool, super micro orientation machanism and so on.

Mechanical Characterization of Electroplated Ni Films by Micro-tensile Testing

Mechanical properties of structural materials are particularly important for design, performance realization and reliability analysis of microelectromechanical systems （MEMS）. Furthermore, accurate database of mechanical properties at the micro scale can provide indispensable reference for establishing MEMS standard. Electroplated nickel film is one of the most favored structural materials used in MEMS, thus its mechanical properties has been studied for many years. However, the measured values show large scatter in Yotmg＇s modulus of nickel film. Young＇s modulus and yield stress of electroplated nickel film are measured by using a micro-tensile testing instrument. The tensile load applied on the specimen is measured by a load cell with accuracy 0.25 mN directly, without additional friction. Through measuring the axial stiffness coefficient of the tensile instnunent in situ, the tensile strain of the specimen is obtained by using two-serial spring model. The electroplated nickel films were fabricated from sulfarnate baths, and the gauge section is 500μm long and 10μm wide nominally, and thickness range between 25 μm and 50μm. The obtained Young＇s modulus from tensile testing is 83＋6 GPa for nickel specimens electroplated at current density of 20 mA/cm2 and it increases to 124＋5 GPa as current density is decreased to 10 mA/cm2. The phenomena are interpreted in terms of porosity of microstructure. The higher current density produced rnicrostucture with low density and high volume fraction of pores, and the microstructure of high porosity corresponds to a lower modulus. The measured values of Young＇s modulus are consistent with those of calculated from the exponential empirical formula between Young＇s modulus and porosity. The micro-tensile testing instrument can also be used for mechanical measurement of other MEMS films.

Measurement of Ca^(2+) Flow in Cochlear Cells Using Non-Invasive Micro-Test Technique

Objective To test Calcium ion(Ca2+) flow at the head and end of outer hair cells(OHCs) in resting state and in response to Nimodipine treatment.Methods Non-invasive micro-test techniques were used to study Ca2+ in isolated OHCs in adult guinea pigs.Results Four types of Ca2+ transport were identified in OHCs on basilar membrane tissue fragments:influx at the head of with efflux at the bottom(type 1):efflux at the head of OHCs with influx at the bottom(type 2);influx at the both head and bottom(type 3);and efflux at the both head and bottom(type 4).However,only type 1 and type 3 of Ca2+ ion transport were detected in the cochlea.We propose that Ca2+ ion transport exists in adult guinea pig cochlear OHCs in resting state and is variable.Ca2 + flow in OHC can be inhibited by Nimodipine in resting state.

Comparison of mechanical properties in welded joint for CO_2 arc welding by using the micro－shear test and impact test

A micro shear testing method which can suit to measure the mechanical properties of heterogeneous materials is introduced, and the properties in each zone of welded joint for CO2 arc welding can be evaluated by using this method in this paper. Moreover, these results are compared with those results of Charpy V-notch impact test and their correlation is discussed.

Elastic modulus of claystone evaluated by nano-/micro-indentation tests and meso-compression tests

Toarcian claystone such as that of the Callovo-Oxfordian is a qualified multiphase material. The claystone samples tested in this study are composed of four main mineral phases: silicates(clay minerals, quartz,feldspars, micas)(z86%), sulphides(pyrite)(z3%), carbonates(calcite, dolomite)(z10%) and organic kerogen(z1%). Three sets of measurements of the modulus of deformability were compared as determined in(i) nanoindentation tests with a constant indentation depth of 2 mm,(ii) micro-indentation tests with a constant indentation depth of 20 mm, and(iii) meso-compression tests with a constant displacement of 200 mm. These three experimental methods have already been validated in earlier studies. The main objective of this study is to demonstrate the influence of the scaling effect on the modulus of deformability of the material. Different frequency distributions of the modulus of deformability were obtained at the different sample scales:(i) in nano-indentation tests, the distribution was spread between 15 GPa and 90 GPa and contained one peak at34 GPa and another at 51 GPa;(ii) in the micro-indentation tests, the distribution was spread between 25 GPa and 60 GPa and displayed peaks at 26 GPa and 37 GPa; and(iii) in the meso-compression tests, a narrow frequency distribution was obtained, ranging from 25 GPa to 50 GPa and with a maximum at around 35 GPa.

Vibration test of micro machined gyroscope based on high speed photography and SURF

Based on three kinds of dynamic test of MEMS, a dynamic system for the vibration test of micro machined gyroscope based on high speed photography is introduced. Firstly, the architecture of the system hardware is introduced. Secondly, the image tracking performance is compared by the test using the template matching algorithm, the mean shift algorithm and the SURF algorithm. The vibration curve shows that high speed photograph combined with SURF algorithm is faster, more ac- curate, and more suitable for the vibration test of micro machined gyroscope. After the frequency a- nalysis and related interpolation, more characteristics of micro gyroscope can be obtained.

Micro-Doppler effect testing technique for attitude of projectile in space flight

To measure projectile attitude in space flight, based on continuous wave （CW） radar, a new micro-Doppler effect testing technique is developed in this paper. It also establishes radar testing model for attitude of flying projectile and resolve micro-Doppler effect of projectile motion attitude. By distinguishing and geting attitude parameters such as micro-motion period, this technique can in- tuitively estimate the flight stability of projectile, and the validity of this technique is proved accord- ing to flight tests.

China,America Have Coo[erated in Micro Biological Production Test

Ｃｈｉｎａ，ＡｍｅｒｉｃａＨａｖｅＣｏｏｐｅｒａｔｅｄｉｎＭｉｃｒｏｂｉｏｌｏｇｉｃａｌＰｒｏｄｕｃｔｉｏｎＴｅｓｔＨｏｕＦｕＴｈｅｍｉｃｒｏｂｉｏｌｏｇｉｃａｌｐｒｏｄｕｃｔｉｏｎｔｅｃｈｎｏｌｏｇｙｈａｓｂｅｅｎｉｎｔｒｏｄｕｃｅｄｆｒｏｍｔｈｅ...

Salt spray corrosion test of micro-plasma oxidation ceramic coatings on Ti alloy

Ceramic coatings were prepared on Ti-6Al-4V alloy in NaAlO2 solution by micro-plasma oxidation （MPO）. The salt spray tests of the coated samples and the substrates were carded out in a salt spray test machine. The phase composition and surface morphology of the coatings were investigated by XRD and SEAM. Severe corrosion occurred on the substrate surface, while there were no obvious corrosion phenomena on the coated samples. The coatings were composed of Al2TiO5 and a little α-Al2O3 and mille TiO2, and the salt spray test did not change the composition of the coatings. The weight loss rate of the coatings decreased with increasing MPO time because of the increase in density and thickness of the coatings. The surface morphology of the coatings was influenced by salt spray corrosion test. Among the coated samples, the coating prepared for 2 h has the best corrosion resistance under salt spray test.

Experimental Tests on a Pre-Heated Combustion Chamber for Ultra Micro Gas Turbine Device: Air/Fuel Ratio Evaluation

Current portable power generators are mainly based on internal combustion engine since they present higher values of efficiency comparing to other engines;the main reason why internal combustion engine is not convenient for micro power generation (5 - 30 kW) is because of their heaviness. Micro and ultra micro gas turbine devices, based on a micro compressor and a micro turbine installed on the same shaft, are more suitable for this scope for several reasons. Micro turbine systems have many advantages over reciprocating engine generators, such as higher power density (with respect to size and weight), extremely low emissions and few, or just one, moving part. Those designed with foil bearings and air-cooling operate without oil, coolants or other hazardous materials. Micro turbines also have the advantage of having the majority of their waste heat contained in their relatively high temperature exhaust. Micro turbines offer several potential advantages compared to other technologies for small-scale power generation, including: a small number of moving parts, compact size, lightweight, greater efficiency, lower emissions, lower electricity costs, and opportunities to utilize waste fuels. The object of this study is the experimental tests on a stand-alone gas turbine device with a pre-heated combustion chamber (CC), to validate the fuel consumption reduction, compared to an actual and commercial device, used on air models.

Fractal characteristics of cracks and fragments generated in unloading rockburst tests

True triaxial rockburst experiments with four different unloading rates were performed on four prism specimens of granite sampled from Beishan, China. The damage evolution in the rockburst test was investigated from two aspects including fracture surface crack and fragment characteristics. The scanning electron microscopy was used to observe the micro crack information on fragment surface. Combing binarization and box counting dimensions, the fractal dimensions of cracks were obtained. Meanwhile,the fragments were collected and a sieving experiment was conducted. We weighed the fragments qualities, counted the amount of fragments and measured the fragments length, width and thickness.Utilizing four methods to calculate damage fractal dimensions of fragments, the trend of fractal value changing with unloading rates can be roughly described. It can be concluded from these experiments that the fractal dimension either for crack or for fragment holds a decreasing trend with the decreasing unloading rate, indicating a reduction of damage level.

CHARACTERIZATION OF THE FRACTURE WORK FOR DUCTILE FILM UNDERGOING THE MICRO-SCRATCH

The interface adhesion strength(or interface toughness)of a thin film/substrate system is often assessed by the micro-scratch test.For a brittle film material,the interface adhesion strength is easily obtained through measuring the scratch driving forces.However,to measure the interface adhesion strength(or in- terface toughness)for a metal thin film material(the ductile material)by the micro- scratch test is very difficult,because intense plastic deformation is involved and the problem is a three-dimensional elastic-plastic one.In the present research,using a double-cohesive zone model,the failure characteristics of the thin film/substrate system can be described and further simulated.For a steady-state scratching pro- cess,a three-dimensional elastic-plastic finite element method based on the double cohesive zone model is developed and adopted,and the steady-state fracture work of the total system is calculated.The parameter relations between the horizontal driving forces(or energy release rate of the scratching process)and the separation strength of thin film/substrate interface,and the material shear strength,as well as the material parameters are developed.Furthermore,a scratch experiment for the Al/Si film/substrate system is carried out and the failure mechanisms are explored. Finally,the prediction results are applied to a scratch experiment for the Pt/NiO material system given in the literature.

Model Identification of a Micro Air Vehicle

This paper is focused on the model identification of a Micro Air Vehicle （MAV） in straight steady flight condition. The identification is based on input-output data collected from flight tests using both frequency and time dorrtain techniques. The vehicle is an in-house 40 cm wingspan airplane. Because of the complex coupled, multivariable and nonlinear dynamics of the aircraft, linear SISO structures for both the lateral and longitudinal models around a reference state were derived. The aim of the identification is to provide models that can be used in future development of control techniques for the MAV.

A MICRO-MECHANICAL MODEL OF KNITTED FABRIC AND ITS APPLICATION TO THE ANALYSIS OF BUCKLING UNDER TENSION IN WALE DIRECTION:MICRO-MECHANICAL MODEL

The typical micro-knitting structure of knitted fabric,which makes it very different from woven fabric,is described.The tensile tests of knitted fabric are reported.The deformations of the micro-knitting structures are carefully studied.The study indicates that when a knitted fabric sheet is subjected to a tension along w-direction an extra compressive stress field inside loop in c-direction is induced.The extra stress field is also determined through analysis.Finally,a micro-mechanical model of knitted fabric is proposed.This work paves the way for the simulations of buckling modes of a knitted fabric sheet as are observed in experiments.

Micro Scan W/A96全自动分析仪对创伤感染细菌进行鉴定及药敏分析

目的探讨临床上创伤感染的病原菌分布和耐药特征,指导临床合理使用抗生素。方法 266份创伤感染细菌标本用BACTEC 9120全自动培养仪培养,然后用Micro Scan W/A 96全自动分析仪对分离细菌进行鉴定和药敏试验。结果分离出菌株228株,其中革兰阳性菌131株(57.4%),革兰阴性菌87株(38.2%),真菌10株(4.4%),这些菌株对多数抗生素耐药性高,只对少部分抗生素较敏感。结论明确创伤感染中病原菌的分布及对抗生素的耐药性,对临床上指导抗生素合理利用有重要意义。

Behaviour of Roofing Materials Facing to Micro-Organisms

An accelerated water-streaming test was used to evaluate several roofing materials regarding their behavior to colonization by algae, by closely reproducing the phenomenon of natural biological soiling. A set of roofing materials with defined physical and chemical characteristics was thus investigated against the colonization by algae. Porosity, roughness and chemical composition showed to be factors of influence in the establishment of those micro-organisms.

Balanced Fertilizer Use through Soil Testing Leads to Higher Yields and Nutrient Contents of Maize Grains

Fertilizers use can be optimized through soil testing and leaf analysis. This paper deals with using soil analysis as a base for fertilizer use in maize. A field experiment was carried out in two summer seasons of 2013 and 2014 with maize (triple hybrid) in Oraby Village, Mariut sector, Alexandria, Egypt. Soil testing shows that soil was clay loam, with high Na and CaCO3 contents with high pH, low organic matter, medium P and K and low micronutrient contents (Fe, Zn, Mn and Cu), seven treatments were designed. The most promising treatment was when P and K were increased and micronutrients were added based on soil testing. This treatment resulted in the highest yield with better grain contents of protein and nutrients which indicated that soil-test based on fertilizer use was superior. Soil analysis at the end of the experiment showed higher P and K contents. This approach could be adopted for regions with similar soil conditions in other parts of the world.

Mechanical Characterization and Micro-Wear of FeB-Fe₂B Layers on Boriding AISI D2 and AISI 4340 Steels

The mechanical behavior and wear of the different hardened phases with bore-induced changes in AISI 4340 and AISI D2 steels were investigated. The hardness and modulus of elasticity were measured by nanoindentation and the values obtained for the layers in AISI D2 steel were 18 GPa and 325 GPa in the Fe2B boride phase, and 20 GPa and 360 GPa in the FeB boride phase, respectively. The AISI 4340 steel presented mainly the Fe2B phase. It was then possible to analyze the coefficient of friction obtained in the Fe2B phase of the steel AISI 4340 presented a range of 0.04 to 0.06. The AISI D2 steel presents two different phases in the boride layer being the coefficient of friction higher for the test in the FeB phase than for Fe2B, and the values vary from 0.065 to 0.075. These parameters were obtained with micro-wear tests. No adhesion failures were observed after the sliding tests in the interface of the two different boride layers. Cracks in the FeB phase after the sliding test were much more frequent.

基于Micro-LED器件光学测试标准的研究

本文基于Micro-LED器件阵列的制备与测试标准的研究,结合目前暂无规范测试标准的情况,尤其是针对单个微尺度芯片的亮度小于一般测量设备灵敏度区间时的特点,提出了一种针对Micro-LED光电特性优化的测试标准。该方法能够有效侦测Micro-LED器件阵列的电学参数和光学参数,尤其是光学均一性和近场光强分布,这对Micro-LED器件方向上国际标准的制定提供了重要的参考依据。

工业固废-水泥固化腐殖土的力学响应和微观机制

为了推动腐殖土在岩土工程领域的资源化利用,采用工业固废(包括生物质飞灰、电石渣和磷石膏)协同水泥对腐殖土进行固化处理。以中国广东省某陈旧型简易垃圾填埋场开采的腐殖土为研究对象,通过常规三轴试验、干湿和冻融循环试验、扫描电镜(SEM)、X射线衍射(XRD)、傅立叶红外光谱(FTIR)和压汞(MIP)测试探究了工业固废-水泥固化腐殖土的三维力学特性、耐久性能及微观机制。试验结果表明:随着P_(o-b)(即工业固废替代水泥的比率)的增加,试样偏应力与轴向应变的关系逐渐由应变软化向应变硬化过渡。三元工业固废的适当掺入(P_(o-b)为25%~50%)有利于减缓干湿循环作用下工业固废-水泥固化腐殖土试样的劣化速率,而纯水泥固化腐殖土试样表现出相对优异的极限偏应力和抗冻性。微观结构分析表明大量钙矾石晶体和C―(A)―S―H凝胶等产物增强了腐殖土颗粒之间的黏结,同时填充了微观孔隙。研究结果可为垃圾填埋场开采的腐殖土修复及再利用提供理论依据。