Large-scale synthesis of nickel sulfide micro/nanorods via a hydrothermal process

Rhombohedral-phase NiS micro/nanorods were synthesized on a large scale through a hydrothermal method using NiCl2·6H2O and thiourea crystals as starting precursors. Recrystallized thiourea was observed to play an important role in the formation of mi- cro/nanosized rods and flower-like structures. The molar ratio and reaction temperature of the precursors influenced the morphology and phase of NiS products. Pure rhombohedral NiS micro/nanorods were obtained on a large scale when the molar ratio between NiCl2·6H2O and thiourea crystals was fixed at 2：1, and the mixture was heated at 250℃ for 5 h. Flower-like NiS nanostructures were formed when the molar ratio between NiCl2·6H2O and thiourea crystals was maintained at 1：1. The Raman and Fourier-transform infrared （FTIR） spectra of the as-prepared rhombohedral NiS micro/nanorods were collected, and their magnetic properties were investigated. The results showed that the FTIR absorption peaks of the as-prepared product are located at 634 cm^-1 and their Raman peaks are located at 216 and 289 cm^-1; the as-prepared NiS micro/nanorods exhibited weak ferromagnetic behavior due to the size effect.

Preparation of carbon fiber cloth supported porous CdS nanorods with excellent photocatalytic activity for Cr(Ⅵ)reduction

The use of visible-light responsive photocatalysts for removing heavy metal ions in wastewater has received great attention.However,the development of photocatalysts with high activity and recyclability remains a huge challenge.Herein,a recyclable carbon fiber cloth-supported porous CdS nanorod photocatalyst was fabricated by a two-step hydrothermal treatment using AgVO_(3) nanowires as templates.The results indicated that under visible-light illumination,the carbon cloth-supported porous CdS nanorods showed improved photocatalytic activity for the reduction of Cr(Ⅵ),with an apparent rate constant exceeding that of carbon cloth-supported CdS nanospheres by a factor of 1.65 times.Moreover,the carbon cloth-supported porous CdS nanorods can be easily separated and be reused.This brings a new perspective for developing photocatalysts with high efficiency and recyclability for wastewater treatment.

不同方法对根管内氢氧化钙去除效果的micro-CT评价

目的:应用显微CT(micro-computed tomography,micro-CT)建立磨牙根管模型,评价不同方法对氢氧化钙的清除效率。方法:收集2023年10月—2024年2月口腔综合科门诊拔除的11颗磨牙(24个根管),按照标准根管治疗流程,镍钛器械预备完成后,在根管内置入氢氧化钙,1周后,根据不同冲洗方法将样本随机分为侧方开口注射器组、超声荡洗组(EMS组)和声波震荡组(EDDY组)等3组(n=8)。冲洗前后使用micro-CT重建根管系统并使用不同颜色标记独立根管,计算各个根管氢氧化钙体积,比较各组氢氧化钙清除率。采用SPSS 19.0软件包对数据进行统计学分析。结果:3种方法均无法完全去净根管内氢氧化钙。使用次氯酸钠作为冲洗液时,超声荡洗和声波震荡清除效果优于侧方开口冲洗器(P<0.05);超声荡洗和声波震荡去除氢氧化钙效率相当,差异无统计学意义(P>0.05);氢氧化钙残留部位集中于根尖区。结论:Micro-CT能较为高效地重建磨牙根管模型,可用于评价氢氧化钙去除效果。超声荡洗组和声波震荡组清除氢氧化钙效率相当,优于侧方开口注射器组。

Micro LED车灯投影光学系统设计与优化

本文提出了一种基于Micro LED阵列的车灯投影方案,设计了以像素尺寸为80μm×80μm的200×150白光Micro LED阵列作为显示光源,视场角为16°×34°的车灯投影光学系统,并对物面倾斜角度和光学系统结构进行了优化。此外,分别采用反向畸变处理方法和像素灰度调制方法用以解决车灯投影图像的梯形畸变和照度均匀性问题,并搭建了投影实验平台,对图像校正方法进行了验证。实验结果表明:校正后图像梯形畸变系数p1,p2分别从0.0932和0.3680下降至0.0835和0.0373,像面照度均匀性从83.2%提高到93.2%。本文通过对基于Micro LED的倾斜投影车灯光学系统进行优化设计及采用图像校正方法,实现了高光效、低畸变的车灯投影。

光子晶体Micro LED微显示阵列加工及光学特性分析

Micro LED器件具有高亮度、低功耗和高可靠性等优点,但Micro LED显示像素巨量转移和光提取效率低的问题为其应用带来挑战。开发了具有高转移效率和出光效率的单片64×64 Micro LED微显示阵列,提出了倒装型GaN基单片Micro LED微显示阵列芯片和Si基驱动电路的设计方法及集成工艺。通过时域有限差分(FDTD)方法对Micro LED微显示阵列光学特性进行了建模分析,设计了一种提高Micro LED微显示阵列出光效率的光提取结构。结合仿真结果,开发了一种在Micro LED蓝宝石衬底表面制备光子晶体结构的聚焦离子束(FIB)微纳加工工艺,并进行了器件加工。测试结果表明,蓝宝石衬底上加工的光子晶体结构可以提高Micro LED器件的表面出光效率,光功率平均值提升了16.36%,对Micro LED微显示阵列加工及微显示像素光提取问题具有借鉴意义。

Porous Microspheres Comprising CoSe2 Nanorods Coated with N-Doped Graphitic C and Polydopamine-Derived C as Anodes for Long-Lived Na-Ion Batteries

Metal–organic framework-templated nitrogen-doped graphitic carbon(NGC)and polydopaminederived carbon(PDA-derived C)-double coated one-dimensional CoSe_(2) nanorods supported highly porous threedimensional microspheres are introduced as anodes for excellent Na-ion batteries,particularly with long-lived cycle under carbonate-based electrolyte system.The microspheres uniformly composed of ZIF-67 polyhedrons and polystyrene nanobeads(φ=40 nm)are synthesized using the facile spray pyrolysis technique,followed by the selenization process(P-CoSe_(2)@NGC NR).Further,the PDA-derived C-coated microspheres are obtained using a solution-based coating approach and the subsequent carbonization process(P-CoSe_(2)@PDA-C NR).The rational synthesis approach benefited from the synergistic effects of dual carbon coating,resulting in a highly conductive and porous nanostructure that could facilitate rapid diffusion of charge species along with efficient electrolyte infiltration and effectively channelize the volume stress.Consequently,the prepared nanostructure exhibits extraordinary electrochemical performance,particularly the ultra-long cycle life stability.For instance,the advanced anode has a discharge capacity of 291(1000th cycle,average capacity decay of 0.017%)and 142 mAh g^(-1)(5000th cycle,average capacity decay of 0.011%)at a current density of 0.5 and 2.0 A g^(-1),respectively.

Microstructure and photocatalytic activity of Ni-doped ZnS nanorods prepared by hydrothermal method

Pure ZnS and Ni^2+-doped ZnS nanorods (Zn1-xNixS, x=0, 0.01, 0.03, 0.05 and 0.07, mole fraction,%) were synthesized by hydrothermal method. The effects of Ni2+ doping on the phase-structure, morphology, elemental composition and optical properties of the samples were investigated by X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), X-ray energy dispersive spectrometry (EDS) and ultraviolet–visible spectroscopy (UV-Vis), respectively. The photocatalytic activity of Zn1-xNixS nanorods was evaluated by the photodegradation of organic dyes Rhodamine B (RhB) in aqueous solution under UV light irradiation. The results show that all samples exhibit wurtzite structure with good crystallization. The morphologies are one-dimensional nanorods with good dispersion, and the distortion of the lattice constant occurs. The band gap of Zn1-xNixS samples is smaller than that of pure ZnS, thus red shift occurs. Ni^2+-doped ZnS nanocrystals can enhance photocatalytic activities for the photodegradation of RhB. Especially, Zn0.97Ni0.03S sample exhibits better photocatalytic performance and photocatalytic stability for the decomposition of RhB.

Application of Monodisperse Thermo-Responsive Composite Microgels with Core-Shell Structure Based on Au@Ag Bimetallic Nanorod as Core in Surface Enhanced Raman Spectroscopy Substrate

The monodisperse Au@Ag bimetallic nanorod is encapsulated by crosslinked poly( N-isopropylacrylamide)( PNIPAM) to produce thermo-responsive composite microgel with well-defined core-shell structure( Au@ Ag NR@ PNIPAM microgel)by seed-precipitation polymerization method using butenoic acid modified Au @ Ag NRs as seeds. When the temperature of the aqueous medium increases from 20℃ to 50℃,the localized surface plasmon resonance( LSPR) band of the entrapped Au @ Ag NR is pronouncedly red-shifted because of the decreased spatial distances between them as a result of shrinkage of the microgels,leading to their plasmonic coupling. The temperature tunable plasmonic coupling is demonstrated by temperature dependence of the surface enhanced Raman spectroscopy( SERS) signal of 1-naphthol in aqueous solution. Different from static plasmonic coupling modes from nanostructured assembly or array system of noble metals,the proposed plasmonic coupling can be dynamically controlled by environmental temperature. Therefore, the thermo responsive hybrid microgels have potential applications in mobile LSPR or SERS microsensors for living tissues or cells.

Microwave-assisted synthesis and characterization of ZnO-nanorod arrays

High density ZnO-nanorod arrays(rod length 1.59μm)were successfully synthesized via a microwave-assisted solution-phase method using zinc chloride and ammonia solution as reactants.The influence of concentration of ammonia solution, work power,and microwave irradiation time on the morphology and size of final products was carefully investigated.The crystal structure,chemical composition and morphologies of final products were characterized using X-ray powder diffraction(XRD), scanning electron microscopy(SEM)and photoluminescence(PL).The as-synthesized ZnO is composed of single crystalline and possesses three photoluminescence emissions centered at 400,469 and 534.5 nm,respectively.

Microwave-assisted synthesis of high aspect ratio ruthenium nanorods

Poly(N-vinyl-2-pyrrolidone)(PVP)-stabilized ruthenium nanorods with high aspect ratio by refluxing ruthenium(Ⅲ) chloride in n-propanol have been successfully prepared by means of a facile and rapid microwave heating for the first time.The structure and morphology of the obtained products were characterized by transmission electron microscopy(TEM),select area electron diffraction(SAED),ultraviolet-visible spectrophotometry(UV-vis),X-ray photoelectron spectroscopy(XPS) and Fourier transform spectroscopy(FT-IR).XPS analysis reveals that the nanorods were in the metallic state.TEM images showed that ruthenium nanorods had an obvious one-dimensional structure with the aspect ratio ranged from 5 to 40 nm and length up to 600 nm.SAED patterns indicated that the nanorods were single-crystalline with a hexagonal structure.

Microstructure Characterization of Single-crystal ZnO Nanorods Synthesized by Solvothermal at Low Temperature

Single-crystalline ZnO nanorods have been synthesized by a simple solvothermal process at low temperature. Transmission electron microscopy （TEM） observations have confirmed that the as-synthesized products have rod-like morphologies with diameters ranging from several nanometers to 30 nm and lengths from 100 nm to 2 μm. Such hexagonal ZnO nanorods are structurally uniform and the growth direction is identified to be [0001]. Growth mechanism of the ZnO nanorods was proposed.

Synthesis and Characterization of La(OH)_3 Nanorods by Hydrothermal Microemulsion Method

La（OH）3 nanorods with diameters of 20-40 nm and lengths of 200-300 nm were synthesized by a hydrothermal microemulsion method. The structure and morphology of the final products were characterized by X-ray powder diffraction （XRD）, transmission electron microscopy （TEM）, and field emission scanning electron microscope （FESEM）.

基于Micro CT的铜导线短路熔痕孔洞特征分析

导线短路是造成电气火灾的重要原因之一。现行国家标准中将导线短路熔痕分为起火前发生的一次短路熔痕和起火后造成的二次短路熔痕,然而现行国家标准中的鉴定仅停留在定性判断的阶段。火灾现场铜导线短路熔痕特征的量化分析研究是国内外研究人员主要关注的重点。本文应用Micro CT技术对铜导线短路熔痕进行断层扫描检测并重构铜导线短路熔痕的3D图像数据,在此基础上统计、归纳、总结铜导线短路熔痕内部孔洞形态及分布等孔洞特征。研究表明,Micro CT能够全面采集铜导线短路熔痕的整体形态和内部孔洞特征,一次短路熔痕与二次短路熔痕内部孔洞半径、表面积、紧密度的特征数据存在差别,可为短路熔痕定性和定量分析判据研究提供新的理论依据。

Photoluminescent Properties of CoMoO_(4)Nanorods Quickly Synthesized and Annealed in a Domestic Microwave Oven

A simple way to prepare α- and β-CoMoO4 nanorods is reported in this paper. CoMoO4xH2O nanorod precursors were obtained using the microwave-assisted hydrothermal (MAH) method. By annealing the as-prepared CoMoO44xH2O precursor at 600℃ for 10 min in a domestic microwave oven, α- and β-CoMoO4 nanorods were prepared. These powders were analyzed by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), Fourier transform Raman microscopy and ultraviolet visible absorption spectroscopy (UV-vis spectra) as well as photoluminescence (PL) measurements. Based on the results, these materials revealed nanorod morphology. PL spectra obtained at room temperature for α- and β-CoMoO4 particles exhibited maximum components around the blue light emission. The results show that the domestic microwave oven has been successfully employed to obtain α- and β-CoMoO4 nanoparticles.

Micro-CT分析跟骨内骨小梁分布及结构特征

背景:跟骨位于足的后下部,受力较大。跟骨外形复杂且不规则,外周有较薄的皮质骨包绕,内部充满大量的骨小梁,探讨骨小梁的微观结构、走行及分布特征有助于提高对跟骨骨折的认识。目的:采用微计算机断层扫描仪(Micro-CT)扫描跟骨标本获得其影像资料,对其内部骨小梁结构进行分析,探讨跟骨内骨小梁的形态、分布及结构特征。方法:采用Micro-CT连续扫描干燥成人跟骨标本,扫描后获得影像图像,将其以DICOM格式存储。导入影像资料到Hiscan Analyzer软件,显示清晰完整的成人跟骨矢状面、冠状面、水平面的图像,逐层观察骨小梁的走行,依据骨小梁走行特点将跟骨矢状面分为6个部分,在以7 mm为标准的相同厚度下,每个部分选择1个49 mm2等面积的兴趣区,三维重建后获得跟骨及骨小梁的立体微观结构,二值化后运用软件计算感兴趣区域内骨小梁的体积分数、表面密度、骨小梁厚度、骨小梁间隙和骨小梁数量参数。结果与结论:①跟骨表面皮质层很薄,内部充满大量骨松质,在Gissane角的骨皮质明显增厚;②跟骨上部的骨小梁体积分数大于跟骨下部前端、中和三角区、跟骨下后部、跟骨结节部、跟骨底部,跟骨结节部的骨小梁体积分数大于跟骨下部前端、中和三角区、跟骨下后部、跟骨底部;跟骨结节部的骨小梁表面密度大于跟骨下部前端、中和三角区、跟骨底部,跟骨上部、跟骨下后部的骨小梁表面密度大于中和三角区;跟骨上部的骨小梁厚度大于跟骨结节部;中和三角区的骨小梁间隙大于跟骨上部、跟骨结节部;跟骨结节部的骨小梁数量大于中和三角区;③中和三角区主要分布杆状骨小梁,骨小梁表面密度最小、体积分数较小、骨小梁间隙最大;该部位骨质较疏松,受到高冲击力时抗压缩能力差,骨小梁最先发生断裂,是易发生骨折的部位。

Micro segment analysis of supercritical methane thermal-hydraulic performance and pseudo-boiling in a PCHE straight channel

The printed circuit heat exchanger(PCHE) is receiving wide attention as a new kind of compact heat exchanger and is considered as a promising vaporizer in the LNG process. In this paper, a PCHE straight channel in the length of 500 mm is established, with a semicircular cross section in a diameter of 1.2 mm.Numerical simulation is employed to investigate the flow and heat transfer performance of supercritical methane in the channel. The pseudo-boiling theory is adopted and the liquid-like, two-phase-like, and vapor-like regimes are divided for supercritical methane to analyze the heat transfer and flow features.The results are presented in micro segment to show the local convective heat transfer coefficient and pressure drop. It shows that the convective heat transfer coefficient in segments along the channel has a significant peak feature near the pseudo-critical point and a heat transfer deterioration when the average fluid temperature in the segment is higher than the pseudo-critical point. The reason is explained with the generation of vapor-like film near the channel wall that the peak feature related to a nucleateboiling-like state and heat transfer deterioration related to a film-boiling-like state. The effects of parameters, including mass flow rate, pressure, and wall heat flux on flow and heat transfer were analyzed.In calculating of the averaged heat transfer coefficient of the whole channel, the traditional method shows significant deviation and the micro segment weighted average method is adopted. The pressure drop can mainly be affected by the mass flux and pressure and little affected by the wall heat flux. The peak of the convective heat transfer coefficient can only form at high mass flux, low wall heat flux, and near critical pressure, in which condition the nucleate-boiling-like state is easier to appear. Moreover,heat transfer deterioration will always appear, since the supercritical flow will finally develop into a filmboiling-like state. So heat transfer deterioration should be taken seriously in the design and safe operation of vaporizer PCHE. The study of this work clarified the local heat transfer and flow feature of supercritical methane in microchannel and contributed to the deep understanding of supercritical methane flow of the vaporization process in PCHE.

Manipulating d-d orbital hybridization induced by Mo-doped Co_(9)S_(8) nanorod arrays for high-efficiency water electrolysis

Precisely refining the electronic structure of electrocatalysts represents a powerful approach to further optimize the electrocatalytic performance.Herein,we demonstrate an ingenious d-d orbital hybridization concept to construct Mo-doped Co_(9)S_(8) nanorod arrays aligned on carbon cloth(CC)substrate(abbreviated as Mo-Co_(9)S_(8)@CC hereafter)as a high-efficiency bifunctional electrocatalyst toward water electrolysis.It has experimentally and theoretically validated that the 4d-3d orbital coupling between Mo dopant and Co site can effectively optimize the H_(2)O activation energy and lower H^(*)adsorption energy barrier,thereby leading to enhanced hydrogen evolution reaction(HER)and oxygen evolution reaction(OER)activities.Thanks to the unique electronic and geometrical advantages,the optimized Mo-Co_(9)S_(8)@CC with appropriate Mo content exhibits outstanding bifunctional performance in alkaline solution,with the overpotentials of 75 and 234 mV for the delivery of a current density of 10 mA cm^(-2),small Tafel slopes of 53.8 and 39.9 mV dec~(-1)and long-term stabilities for at least 32 and 30 h for HER and OER,respectively.More impressively,a water splitting electrolylzer assembled by the self-supported Mo-Co_(9)S_(8)@CC electrode requires a low cell voltage of 1.53 V at 10 mA cm^(-2)and shows excellent stability and splendid reversibility,demonstrating a huge potential for affordable and scalable electrochemical H_(2) production.The innovational orbital hybridization strategy for electronic regulation herein provides an inspirable avenue for developing progressive electrocatalysts toward new energy systems.

Synthesis of Crystallized BaWO₄Nanorods in a Microemulsion System

BaWO4 nanorods have been successfully synthesized in w/o microemulsion system containing barium ions via a simple reaction between Ba2+ and . The BaWO4 Nanorods were characterized by XRD, TEM, and SEM, respectively. Results showed that the solvents composition—volume ratio of 4-dioxane and distilled water—played the key role in the formation of BaWO4 Nanorods. Furthermore, the strong vibration at 925 cm﹣1 on its Raman spectrum indicated that the BaWO4 nanorods is good at stimulating Raman scattering in transient and steady-state, making it as a promising candidate material for laser with self-raman conversion of radiation inside the active medium.

Simple Template-Free Synthesis of Bi₂O₃Microflowers Composed of Nanorods

This paper reports that α-Bi2O3 microflowers can be synthesized by an extremely simple and easy approach of inducing a reaction through the addition of NaOH aqueous solution to a mixed aqueous solution of Bi(NO3)3·5H2O and HNO3 scanning electron microscopy images of the Bi2O3 microflowers indicate that the Bi2O3 nanorods grew radially from the centre of the microflower to form the microflower shape. The findings of this study show that control of the reaction temperature, reaction time, and raw material mixture ratio plays an important role in the formation of α-Bi2O3 microflowers. It is especially revealed that α-Bi2O3 microflowers can be formed at low temperatures with short reaction times. It has thus far been reported that flower-shaped Bi2O3 particles or their precursors can be synthesized by the addition of additives such as organic molecules or certain inorganic ions. The present work reports on the discovery of ways to synthesize flower-shaped Bi2O3 particles without the use of special additives.

Advances in microfluidic-based DNA methylation analysis

DNA methylation has been extensively investigated in recent years,not least because of its known relationship with various diseases.Progress in analytical methods can greatly increase the relevance of DNA methylation studies to both clinical medicine and scientific research.Microflu-idic chips are excellent carriers for molecular analysis,and their use can provide improvements from multiple aspects.On-chip molecular analysis has received extensive attention owing to its advantages of portability,high throughput,low cost,and high efficiency.In recent years,the use of novel microfluidic chips for DNA methylation analysis has been widely reported and has shown obvious superiority to conventional methods.In this review,wefirst focus on DNA methylation and its applications.Then,we discuss advanced microfluidic-based methods for DNA methylation analysis and describe the great progress that has been made in recent years.Finally,we summarize the advantages that microfluidic technology brings to DNA methylation analysis and describe several challenges and perspectives for on-chip DNA methylation analysis.This review should help researchers improve their understanding and make progress in developing microfluidic-based methods for DNA methylation analysis.