Trends and Overview Regarding the Involvement of Micro-Grids in Modern Power Systems

Customer satisfaction and participation in utility supply packages is the first and foremost factor in the success of any supplying agency whether wholesale or retail dealer. The paper presents the concept of major prospects of non- autonomous micro-grids installed in a certain locality. The article shows the basic background that is required for the installment of micro grid in a particular area and discusses the primary factors or pre-requisites that are required for the existence and operation of micro-grids. It elaborate the major profitable applications and benefits that developing and developed states get by using micro-grids in an area where utility grid is already functioning .It also explains the basic improvement in the quality of supply from micro grid after its installment. It also throws light on afterwards impact on society with this system, such impacts include reliability, tariff rates, economics etc. The article discusses micro-grids as the future of modern power systems. This paper shows significance of modernization by latest topologies in power systems and its effect that will come afterwards.

Intelligent Fuzzy Based High Gain Non-Isolated Converter for DC Micro-Grids

Renewable electricity options, such as fuel cells, solar photovoltaic,and batteries, are being integrated, which has made DC micro-grids famous.For DC micro-grid systems, a multi input interleaved non-isolated dc-dcconverter is suggested by the use of coupled inductor techniques. Since itcompensates for mismatches in photovoltaic devices and allows for separateand continuous power flow from these sources. The proposed converter hasthe benefits of high gain, a low ripple in the output voltage, minimal stressvoltage across the power semiconductor devices, a low ripple in inductorcurrent, high power density, and high efficiency. Soft-switching techniquesare used to realize that the reverse recovery issue of the diodes is moderated, the leakage energy is reused, and no new scheme is appropriated. Toreduce conduction losses, minimum voltage rating MOSFETs with a low ONresistance can be utilized. The converter can supply the required power fromthe load in the absence of one or two resources. Furthermore, due to the highgain of boosting voltage, the converter works in an Adaptive Neuro-FuzzyInference System (ANFIS). The operation principle, steady-state analysis ofthe proposed converter, is given and simulated utilizing MATLAB/Simulinksimulation software.

Distributed Economic MPC for Synergetic Regulation of the Voltage of an Island DC Micro-Grid

In this paper,distributed model predictive control(DMPC) for island DC micro-grids(MG) with wind/photovoltaic(PV)/battery power is proposed,which coordinates all distributed generations(DG) to stabilize the bus voltage together with the insurance of having computational efficiency under a real-time requirement.Based on the feedback of the bus voltage,the deviation of the current is dispatched to each DG according to cost over the prediction horizon.Moreover,to avoid the excessive fluctuation of the battery power,both the discharge-charge switching times and costs are considered in the model predictive control(MPC) optimization problems.A Lyapunov constraint with a time-varying steady-state is designed in each local MPC to guarantee the stabilization of the entire system.The voltage stabilization of the MG is achieved by this strategy with the cooperation of DGs.The numeric results of applying the proposed method to a MG of the Shanghai Power Supply Company shows the effectiveness of the distributed economic MPC.

Power-Sharing Enhancement Using Harmonized Membership Fuzzy Logic Droop Control Based Micro-Grid

The contribution of Renewable Energy Resources(RER)in the process of power generation is significantly high in the recent days since it paves the way for overcoming the issues like serious energy crisis and natural contamination.This paper deals with the renewable energy based micro-grid as it is regarded as the apt solution for integrating the RER with the electrical frameworks.As thefixed droop coefficients in conventional droop control approaches have caused various limitations like low power-sharing and sudden drops of grid voltage in the Direct Current(DC)side,the Harmonized Membership Fuzzy Logic(MFL)droop control is employed in this present study.This proposed droop control for the hybrid PV-wind-battery system with MFL assists in achieving proper power-sharing and minimizing Total Harmonic Distortion(THD)in the emer-gency micro-grid.It eradicates the deviations in voltage and frequency with itsflexible and robust operation.The THD is reduced and attains the value of 3.1%compared to the traditional droop control.The simulation results of harmo-nized MFL droop control are analogized with the conventional approaches to vali-date the performance of the proposed method.In addition,the experimental results provided by the Field Programmable Gate Array(FPGA)based laboratory setup built using a solar photovoltaic(PV)and wind Permanent Magnet Synchro-nous Generator(PMSG)reaffirms the design.

Optimal Bidding Strategies of Microgrid with Demand Side Management for Economic Emission Dispatch Incorporating Uncertainty and Outage of Renewable Energy Sources

In the restructured electricity market,microgrid(MG),with the incorporation of smart grid technologies,distributed energy resources(DERs),a pumped-storage-hydraulic(PSH)unit,and a demand response program(DRP),is a smarter and more reliable electricity provider.DER consists of gas turbines and renewable energy sources such as photovoltaic systems and wind turbines.Better bidding strategies,prepared by MG operators,decrease the electricity cost and emissions from upstream grid and conventional and renewable energy sources(RES).But it is inefficient due to the very high sporadic characteristics of RES and the very high outage rate.To solve these issues,this study suggests non-dominated sorting genetic algorithm Ⅱ(NSGA-Ⅱ)for an optimal bidding strategy considering pumped hydroelectric energy storage and DRP based on outage conditions and uncertainties of renewable energy sources.The uncertainty related to solar and wind units is modeled using lognormal and Weibull probability distributions.TOU-based DRP is used,especially considering the time of outages along with the time of peak loads and prices,to enhance the reliability of MG and reduce costs and emissions.

Optoelectronic characterisation of an individual ZnO nanowire in contact with a micro-grid template

Optoelectronic characterisation of an individual ZnO nanowire in contact with a micro-grid template has been studied. The low-cost micro-grid template made by photolithography is used to fabricate the ohmic contact metal electrodes. The current increases linearly with the bias, indicating good ohmic contacts between the nanowire and the electrodes. The resistivity of the ZnO nanowire is calculated to be 3.8 Ω·cm. We investigate the photoresponses of an individual ZnO nanowire under different light illumination using light emitting diodes （λ= 505 nm, 460 nm, 375 nm） as excitation sources in atmosphere. When individual ZnO nanowire is exposured to different light irradiation, we find that it is extremely sensitive to UV illumination; the conductance is much larger upon UV illumination than that in the dark at room temperature. This phenomenon may be related to the surface oxygen molecule adsorbtion, which indicates their potential application to the optoelectronic switching device.

Optimal configuration strategy of energy storage system in high photovoltaic penetration micro-grid based on voltage sensitivity analysis

Energy storage is an effective measure to deal with internal power fluctuation of micro-grid and ensure stable operation, especially in the micro-grid with high photovoltaic(PV) penetration. Its capacity configuration is related to the steady, safety and economy of micro-grid.In order to improve the absorptive capacity of micro-grid on maximizing the use of distributed PV power in micro-grid, and improve the power quality, an optimal energy storage configuration strategy is proposed, which takes many factors into account, such as the topology of micro-grid, the change of irradiance, the load fluctuation and the cable. The strategy can optimize the energy storage allocation model to minimize the storage power capacity and optimize the node configuration.The key electrical nodes are identified by using the sensitivity coefficient of the voltage, and then the model is optimized to simplify calculation. Finally, an example of the European low-voltage micro-grid and a micro-grid system in the laboratory is used to verify the effectiveness of the proposed method.The results show that the proposed method can optimize the allocation of capacity and the node of the energy storage system.

Design of a Monitoring System of Micro-Grid

This paper describes a micro-grid system and its monitoring system. This micro-grid system consists of generation systems, consumer electrical equipments, auxiliary equipments and the monitoring system. All the equipments have 485 communication interfaces. In order to monitor and manage this micro-grid system, we built a monitoring system, which contains modular instrument system and industrial personal computer. In order to keep real time, we adopt some measures in software and hardware. We adopt LABVIEW and its program modules in software and adopt modular instrument system in hardware. Supporting by the software and hardware, the micro-grid system can be safe and stable.

Voltage Stabilization of Hybrid Micro-Grid Using Super Capacitors

Scarcity of fossil fuel resources has motivated the researchers to develop renewable energy based power projects. Instead of using a single or independent renewable energy source, it is preferable to use the combination of such energy sources in a distributed way to compensate the power fluctuations of the system and this leads to the concept of hybrid micro-grid energy. Voltage stability is an important parameter for the secure operation of the hybrid-micro grid, and IEEE 1547 Standard defines the limit of the voltage for the successful operation of the micro-grid. Although Vanadium Redox Batteries (VRBs) can help the system to stabilize the voltage when voltage sag occurs when a heavy load is suddenly connected to the system, this stabilization process takes some time. This paper discusses the application of super capacitors to the hybrid micro-grid system, as a higher energy density element, to help the system quickly recover its transient voltage.

Harmonic Suppression Method Based on Immune Particle Swarm Optimization Algorithm in Micro-Grid

Distributed generation has attracted great attention in recent years, thanks to the progress in new-generation technologies and advanced power electronics. And micro-grid can make full use of distributed generation, so it has been widespread concern. On the other hand due to the extensive use of power electronic devices and many of the loads within micro-grid are nonlinear in nature, Micro-grid generate a large number of harmonics, so harmonics pollution needs to be addressed. Usually we use passive filter to filter out harmonic, in this paper, we propose a new method to optimize the filter parameters, so passive filter can filter out harmonic better. This method utilizes immune particle swarm optimization algorithm to optimize filter parameters. It can be shown from the simulation results that the proposed method is effective for micro-grid voltage harmonics compensation.

Study and Implementation on Batteries Charging Method of Micro-Grid Photovoltaic Systems

In the micro-grid photovoltaic systems, the random changes of solar radiation enable lead-acid batteries to experience low SOC (State of Charge) or overcharged for periods of time if directly charged with such traditional methods as decreased charging current, which will reduce lifetime of batteries. What’s more, it’s difficult to find a proper reduction coefficient in decreasing charging current. To adapt to the random changes of circumstance and avoid selecting the reduction coefficient, a new fast charging method named decreased charging current based on SOC is proposed to apply into micro-grid photovoltaic systems. It combines batteries’ SOC with the maximum charging voltage to determine the charging rate without strictly selecting reduction coefficient. By close-loop current control strategy and related scheme, the experiment proves the new method is feasible and verifies that, comparing with decreased charging current, the improved method make batteries’ SOC reach 100% in shorter time as well as the temperature of batteries raise more slowly.

Control System Development and Test for the Operation of a Micro-Grid System—PART I

This paper presents design, analysis and simulation performance of an active power controller for stable and reliable operation of a micro-grid system. Power balance between generation and consumer is a critical issue for stable and reliable operation of the micro-grid systems. This issue becomes more critical when a micro-grid system contains stochastic nature distributed generations such as wind and solar because their output power changes non-uniformly. In order to achieve accurate and fast power balance in such a micro-grid system, power in the system has to be regulated continuously. Such an objective can be achieved using droop based alternating current control technique. Because the droop characteristic employed into the developed controller initiates determining the power deviation in the system which is continuously regulated by controlling the current flow into dump power resistors. The designed controller is simulated for the operation of a micro-grid system in stand-alone mode under various operating conditions. The simulated results show the ability of the developed controller for stable and reliable operation of the micro-grid that contains renewable sources. The experimental development of the micro-grid system and the testing of the developed active power controller are presented in PART II of this paper.

Micro-Grid Smooth Switchover Method Based on Controller State Following

Micro-grid smooth switchover between different operation modes is important for steady operation and reliable power supply of micro-grid. In order to reduce the transient fluctuation of voltage and frequency during switchover, this paper proposed a new switchover method based on controller state following. When transferring to island mode, the control method for inverter of storage device changed from PQ control to V/f control. Before switchover, the output of V/f controller is always following the output of PQ controller. So that the sudden change of output is avoided at the moment of switchover. A micro-grid model with photovoltaic and battery is built on DIgSILENT Power Factory simulation software, to simulate micro-grid switchover from grid-connected mode to island mode. Results show this method can effectively suppress the transient fluctuation of voltage and frequency, and reduce the influence of transient process on power grid. This conclusion has important practical significance on micro-grid smooth switchover from grid-con- nected mode to island mode.

Optimal Partitioning of Distribution Networks for Micro-Grid Operation

A great concern for the modern distribution grid is how well it can withstand and respond to adverse conditions. One way that utilities are addressing this issue is by adding redundancy to their systems. Likewise, distributed generation (DG) is becoming an increasingly popular asset at the distribution level and the idea of microgrids operating as standalone systems apart from the bulk electric grid is quickly becoming a reality. This allows for greater flexibility as systems can now take on exponentially more configurations than the radial, one-way distribution systems of the past. These added capabilities, however, make the system reconfiguration with a much more complex problem causing utilities to question if they are operating their distribution systems optimally. In addition, tools like Supervisory Control and Data Acquisition (SCADA) and Distribution Automation (DA) allow for systems to be reconfigured faster than humans can make decisions on how to reconfigure them. As a result, this paper seeks to develop an automated partitioning scheme for distribution systems that can respond to varying system conditions while ensuring a variety of operational constraints on the final configuration. It uses linear programming and graph theory. Power flow is calculated externally to the LP and a feedback loop is used to recalculate the solution if a violation is found. Application to test systems shows that it can reconfigure systems containing any number of loops resulting in a radial configuration. It can connect multiple sources to a single microgrid if more capacity is needed to supply the microgrid’s load.

Simulation and Analysis of a Compact Electronic Infrastructure for DC Micro-Grid: Necessity and Challenges

Complex circuitry of electronic infrastructure of compact micro-grids with multiple renewable energy sources feeding the loads using parallel operation of inverters acts as a deterrent in developing such systems. This paper deals with applicable techniques reducing the driving circuits in parallel power inverters used in micro-grid system (MGS), mainly focused on the distributed generation (DG) in islanded mode. The method introduced in this paper, gives a minimal and compressed circuitry that can be implemented very cost-effectively with simple components. DC micro-grids are proposed and researched for the good connection with DC output type sources such as photovoltaic (PV), fuel cell, and secondary battery. In this paper, the electronic infrastructure of micro-grid is expressed. Then discussed the reasons for its complexity and the possibility of reducing the elements of electronic circuits are investigated. The reason for this is in order to compact DC micro-grid system for electrification to places like villages. Digital Simulation in Matlab Simulink is used to show the effectiveness of this novel driver topology for parallel operating inverters (NDTPI).

Control System Development and Test for the Operation of a Micro-Grid System—PART II

This paper presents experimental development and performance testing of an active power controller for stable and reliable operation of a micro-grid system. In order to achieve accurate and fast power balance in a micro-grid system that contains renewable energy sources, power in the system has to be regulated continuously. Such an objective can be achieved using droop based alternating current control technique. Because the droop characteristic employed into the developed controller initiates to determine the power deviation in the system which is continuously regulated by controlling the current flow into dump power resistors. The designed controller is tested and validated using a micro-grid prototype in the laboratory environment for stand-alone mode of operation under various operating conditions. The key development in the micro-grid prototype is the development of a wind turbine simulator. A dSPACE ds1104 DSP board is used to implement and interface the designed controller with the micro-grid system. The experimental investigation of the developed controller presents the significant capability to achieve continuous power balance in the micro-grid system, while it maintains stable and reliable operation of the system. Finally, the power quality of the isolated micro-grid system is presented and discussed under the operation of the developed controller.

Micro-Grid Planning with Aggregator’s Role in the Renewable Inclusive Prosumer Market

The paper proposes a model for a micro-grid architecture incorporating the role of aggregators and renewable sources on the prosumer side, working together to optimize configurations and operations. The final model takes the form of a mixed-integer linear programming model. This model is solved using the CPLEX solver via GAMS by having a consistent data set.

Managing of Smart Micro-Grid Connected Scheme Using Group Search Optimization

This article introduces a group search optimization (GSO) based tuning model for modelling and managing Smart Micro-Grids connected system. In existing systems, typically tuned PID controllers are engaged to point out the load frequency control (LFC) problems through different tuning techniques. Though, inappropriately tuned PID controller may reveal pitiable dynamical reply and also incorrect option of integral gain may even undermine the complete system. This research is used to explain about an optimized energy management system through Group Search Optimization (GSO) for building incorporation in smart micro-grids (MGs) with zero grid-impact. The essential for this technique is to develop the MG effectiveness, when the complete PI controller requires to be tuned. Consequently, we proposed that the proposed GSO based algorithm with appropriate explanation or member representation, derivation of fitness function, producer process, scrounger process, and ranger process. An entire and adaptable design of MATLAB/SIMULINK also proposed. The related solutions and practical test verifications are given. This paper verified that the proposed method was effective in Micro-Grid (MG) applications. The comparison results demonstrate the advantage of the proposed technique and confirm its potential to solve the problem.

Economic Feasibility of Micro-Grid Energy Storage and the Impact of Emerging Technologies on Its Viability

Currently, energy storage devices show great promise when used in micro-grid applications, and further advancements in this technology will lead to economically-viable and environmentally-friendly solutions in regards to residential energy consumption. Creating a 21st-century energy infrastructure will be fundamental to society in the coming decades and ensuring cost-effective means of doing so will lessen the burden on the average consumer. While current research has focused primarily on fundamental battery research, the economic viability for the average American consumer has been neglected in many cases. In this work, current and future methods of home energy storage are analyzed via a thorough literature review and the most promising current and near-future methods are explored. These methods include current Lithium-Ion Battery (LIB) technology, reused LIB from Electric Vehicles (EVs), Lithium Nickel manganese cobalt oxides (NMC) cathode composition and the utilization of silicon as an anode material. After the potential of these technologies is explored, an analysis of their economic viability for the average consumer is presented. The literature review demonstrates that the current state of LIB is very close to economically feasible;reused LIBs are less viable than new LIBs, and future LIB compositions show great promise in viability. This shows that within the next decade, micro-grids will be a reasonable alternative to utility energy harnessing techniques, and a major step towards green energy consumption will be realized. Hybrid energy storage systems, on the other hand, are shown to be economically infeasible, in the near future, due to their high cost per kWh. However, when analyzing the energy storage capabilities of these systems, it is shown that they may be vital in updated energy infrastructure and provide a cost saving.

Deep Learning-Based FOPID Controller for Cascaded DC-DC Converters

Smart grids and their technologies transform the traditional electric grids to assure safe,secure,cost-effective,and reliable power transmission.Non-linear phenomena in power systems,such as voltage collapse and oscillatory phenomena,can be investigated by chaos theory.Recently,renewable energy resources,such as wind turbines,and solar photovoltaic(PV)arrays,have been widely used for electric power generation.The design of the controller for the direct Current(DC)converter in a PV system is performed based on the linearized model at an appropriate operating point.However,these operating points are everchanging in a PV system,and the design of the controller is usually accomplished based on a low irradiance level.This study designs a fractional-order proportional-integrated-derivative(FOPID)controller using deep learning(DL)with quasi-oppositional Archimedes Optimization algorithm(FOPID-QOAOA)for cascaded DC-DC converters in micro-grid applications.The presented FOPIDQOAOA model is designed to enhance the overall efficiency of the cascaded DC-DC boost converter.In addition,the proposed model develops a FOPID controller using a stacked sparse autoencoder(SSAE)model to regulate the converter output voltage.To tune the hyper-parameters related to the SSAE model,the QOAOA is derived by the including of the quasi-oppositional based learning(QOBL)with traditional AOA.Moreover,an objective function with the including of the integral of time multiplied by squared error(ITSE)is considered in this study.For validating the efficiency of the FOPID-QOAOA method,a sequence of simulations was performed under distinct aspects.A comparative study on cascaded buck and boost converters is carried out to authenticate the effectiveness and performance of the designed techniques.