Metamaterials and metasurfaces for designing metadevices:Perfect absorbers and microstrip patch antennas

In the past twenty years, electromagnetic metamaterials represented by left-handed metamaterials（LHMs） have attracted considerable attention due to the unique properties such as negative refraction, perfect lens, and electromagnetic cloaks. In this paper, we present a comprehensive review of our group＇s work on metamaterials and metasurfaces. We present several types of LHMs and chiral metamaterials. As a two-dimensional equivalent of bulk three-dimensional metamaterials, metasurfaces have led to a myriad of devices due to the advantages of lower profile, lower losses, and simpler to fabricate than bulk three-dimensional metamaterials. We demonstrate the novel microwave metadevices based on metamaterials and metasurfaces： perfect absorbers and microwave patch antennas, including novel transmission line antennas,high gain resonant cavity antennas, wide scanning phased array antennas, and circularly polarized antennas.

Wireless Strain Measurement Based on a Microstrip Patch Antenna

Wireless interrogation of a rectangular microstrip patch antenna for strain measurement is investigated by simulations.To analyze the antenna performance,a microstrip line-feeding patch antenna at 10 GHz is designed.A patch antenna wirelessly fed by a horn is proposed to measure the strain.The direction information of strain detected by the patch antenna is also considered.The strain can be detected both in the width and length directions.It is shown that the strain can be measured wirelessly using a standard horn antenna.This kind of wireless strain-sensing technique offers significant potential for wireless structural health monitoring(SHM),especially for high-end equipment.

A Simplified Full-Wave Analysis for Microstrip Patch Antennas

The spectral domain integral equation(SDIE) provides an accurate and efficient method for computing the resonant frequency, radiation patterns, etc . Using continuous Fourier transform, the formulation utilizes the singular integral equations via the Glerkin's method to derive the deterministic equation with fewer mathematical manipulations. In contrast, discrete Fourier transform(DFT) requires intricate mathematical labor. The present scheme requires a small size, i.e ., (2×2) matrix, and it is possible to extract higher order modal solutions conveniently. Moreover, computation is reduced with the same convergence properties. Based on the present scheme, some results for resonant frequency and radiation patterns compared with available data and computed current distribution on the patch are presented.

Different Feeding Techniques of Microstrip Patch Antennas with Spiral Defected Ground Structure for Size Reduction and Ultra-Wide Band Operation

Different feeding techniques of microstrip patch antennas with different spiral defected ground structures are presented in this paper. The investigated structures illustrate some merits in designing multi-electromagnetic band-gap structures by adjusting the capacitance and changing the inductance through varying the width and length of spiral defected ground structure. Then by applying the three different spirals shapes (one, two and four arms) as the ground plane of microstrip patch antenna with different feeding techniques to create multi or ultra wide-band, improve the antenna gain and reduce the antenna size, it is found that the four arms spiral defected ground structure of microstrip patch antenna with offset feed gives good performance, electrical size reduction to about 75% as compared to the original patch size and ultra-wide bandwidth extends from 2 GHz up to 12 GHz with ?8 dB impedance bandwidth.

A four spiral slots microstrip patch antenna for radiotelemetry capsules based on FDTD

Antenna is very crucial to radiotelemetry capsules which can measure the physiological parameters of the gastroin- testinal (GI) tract. The objective of this paper is to design a novel spiral slots microstrip patch antenna for the radiotelemetry capsules communicating with external recorder at 915 MHz located in ISM (Industry, Science, and Medical) bands. The microstrip patch antenna is designed and evaluated using the finite-difference time-domain (FDTD) method. Return loss characteristics and the effect of the human body on resonant frequency are analyzed, and the performances of radiation patterns at different positions of the human alimentary tract are also estimated. Finally, specific absorption rate (SAR) computations are performed, and the peak 1-g and 10-g SAR values are calculated. According to the peak SAR values, the maximum delivered power for the designed antenna was found so that the SAR values of the antenna satisfy the ANSI (American National Standards Institute) limitations.

RECONFIGURABLE DUAL-BAND CIRCULARLY POLARIZED MICROSTRIP PATCH ANTENNA FOR WIRELESS APPLICATIONS

A new design of reconfigurable single-feed circular patch microstrip antenna for dual-band circular polarization application is proposed. The dual-band functionality is realized through incorporating cross-slots of equal slot length in the circular patch and utilizing two PIN diodes to switch the slots on or off. A pairs of tuning stubs are used to tune the circular polarization performance. The design process is presented and good results were obtained.

Increasing Microstrip Patch Antenna Bandwidth by Inserting Ground Slots

Microstrip patch antenna (MPA) is widely implemented in different communication systems. One of the main disadvantages of MPA which limits its applications is its narrow bandwidth. In this paper I enhanced the bandwidth of MPA by inserting multiple slots in its ground plane. I used FR-4 substrate to design this antenna. The dimensions of this antenna are 59 mm and 79 mm. The dielectric constant is 4.4 and the height is 1.6 mm. I inserted up to 15 slots in ground plane with 1mm width. The spacing between slots is 3 mm. I investigated two designs. In the first design, slots were arranged in parallel to the feeding line. In the second one, slots were arranged horizontally to the feeding line. The main objective of this paper is to design and simulate MPA suitable for wide number of applications. Antenna bandwidth improvement is 18%. All the simulations were obtained by using HFSS simulator.

Rectangular Microstrip Patch Antenna Using Air as Substrate for S-Band Communication

A Rectangular Microstrip Patch Antenna model is proposed using air as a substrate to study the characteristics of designed antenna. The dimensions of designed antenna are 17 mm × 16.66 mm with substrate at frequency 3.525 GHz. In this paper, the simulation is performed by using software Computer Simulation Technology (CST) Microwave studio based on finite difference time domain technique. The characterization of the designed antenna was analyzed in terms of return loss, bandwidth, directivity, gain, radiation pattern, VSWR.

A Linear Array Antenna of Microstrip Patch Antennas Fed by the Open-End of Coplanar Waveguides

In this study, we constructed a 4-element linear array antenna using four 20 GHz band microstrip patch antennas with a structure such that the signal is fed to the patch antennas from open-end coplanar waveguides without contact. We investigated factors related to the design of linear array patch antennas. To adjust the maximum radiation direction and reduce return loss, we optimized the spacing between the elements and their shape. With an element spacing of 11.50 mm, patch width of 3.90 mm, and patch length of 4.15 mm, we obtained a resonance frequency of 20.05 GHz and a return loss of -29.59 dB at the resonance frequency. However, in the case of a 4-element linear array antenna structure, undesired resonances occurred in frequency bands other than the design resonance frequency band of 20 GHz. To suppress these undesired resonances and obtaining stable operation at the design frequency, we propose a new structure in which the feed line is loaded with a short stub, and show through computer simulations that the occurrence of undesired resonances can be sufficiently suppressed. Furthermore, we demonstrate the problem of radiation gain reduction caused by introducing a short stub, propose a design method for a new structure in which the feed line has slits between the stubs, and show improvement of the antenna gain by 0.5 dBi.

Design and Development of a 2 ×1 Array of Slotted Microstrip Line Fed Shorted Patch Antenna for DCS Mobile Communication System

Compact microstrip antennas have recently received much attention due to the increasing demand of small antennas for personal communication equipment. The problem of achieving a wide impedance bandwidth for compact microstrip antennas is becoming an important topic in microstrip antenna design. In this paper the design and development of a 2 × 1 array of a low cost slotted microstrip line fed shorted patch antenna (MFSPA) has been presented. Both the shorted patch and microstrip line feed network have air substrate. The material cost is thus reduced to a minimum. The array consists of two adjacent patches fed, using a simple microstrip T network. The impedance bandwidth of nearly 40%, covering the bandwidth requirement of 1750 MHz band is obtained. Also the antenna exhibits dual band operation. The cross polarization radiation in H-Plane observed with a single element antenna has been reduced considerably with 2 × 1 array. A peak antenna gain of 9.2 dBi is obtained with a small variation of 0.8 dBi. From the results obtained it is clear that the antenna array studied has a low cost fabrication and is suitable for applications in DCS mobile communication base station.

Higher Order OAM Mode Generation Using Wearable Antenna for 5G NR Bands

This paper presents a flexible and wearable textile array antenna designed to generate Orbital Angular Momentum(OAM)waves with Mode+2 at 3.5 GHz(3.4 to 3.6 GHz)of the sub-6 GHz fifth-generation(5G)New Radio(NR)band.The proposed antenna is based on a uniform circular array of eight microstrip patch antennas on a felt textile substrate.In contrast to previous works involving the use of rigid substrates to generate OAM waves,this work explored the use of flexible substrates to generate OAM waves for the first time.Other than that,the proposed antenna was simulated,analyzed,fabricated,and tested to confirm the generation of OAMMode+2.With the same design,OAM Mode−2 can be generated readily simply by mirror imaging the feed network.Note that the proposed antenna operated at the desired frequency of 3.5 GHz with an overall bandwidth of 400 MHz in free space.Moreover,mode purity analysis is carried out to verify the generation of OAM Mode+2,and the purity obtained was 41.78%at free space flat condition.Furthermore,the effect of antenna bending on the purity of the generated OAM mode is also investigated.Lastly,the influence of textile properties on OAM modes is examined to assist future researchers in choosing suitable fabrics to design flexible OAM-based antennas.After a comprehensive analysis considering different factors related to wearable applications,this paper demonstrates the feasibility of generating OAMwaves using textile antennas.Furthermore,as per the obtained Specific Absorption Rate(SAR),it is found that the proposed antenna is safe to be deployed.The findings of this work have a significant implication for body-centric communications.

Design of a High-Gain 2 × 1 Array Antenna for S-Band Applications

Antennas are an indispensable element in wireless networks. For long-distance wireless communication, antenna gains need to be very strong (highly directive) because the signal from the antenna loses a lot of strength as it travels over long distances. This is true in the military with missile, radar, and satellite systems, etc. Antenna arrays are commonly employed to focus electromagnetic waves in a certain direction that cannot be achieved perfectly with a single-element antenna. The goal of this study is to design a rectangular microstrip high-gain 2 × 1 array antenna using ADS Momentum. This microstrip patch array design makes use of the RT-DUROID 5880 as a substrate with a dielectric constant of 2.2, substrate height of 1.588 mm, and tangent loss of 0.001. To achieve efficient gain and return loss characteristics for the proposed array antenna, RT-Duroid is a good choice of dielectric material. The designed array antenna is made up of two rectangular patches, which have a resonance frequency of 3.3 GHz. These rectangular patches are excited by microstrip feed lines with 13 mm lengths and 4.8 mm widths. The impedance of the patches is perfectly matched by these transmission lines, which helps to get better antenna characteristics. At a resonance frequency of 3.3 GHz, the suggested antenna array has a directivity of 10.50 dB and a maximum gain of 9.90 dB in the S-band. The S parameters, 3D radiation pattern, directivity, gain, and efficiency of the constructed array antenna are all available in ADS Momentum.

Radiation Characteristics of Rectangular Patch Antennas with an Array of Pins

有有优秀放射特征的一连串的大头针(大头针数组补丁天线)的补丁天线被调查因为在一条大头针数组补丁天线的水平飞机的各种各样的底层 thicknesses.The 放射是到常规补丁 antenna.And 的很小的 campared 前面的放射的增加和减少向后一条大头针数组补丁天线的放射比这些常规 one's.Also 是 tained 一个大头针数组的电子飞机放射模式的一半力量

A NOVEL WIDE-BAND CIRCULAR PATCH ANTENNA

In order to overcome the narrow-bandwidth of the patch antenna, one kind of configuration which can widen the bandwidth significantly is discussed in this letter. Analyzed by the equivalent-circuits method and simulated by HFSS, a rule derived from simulated results that can aid to design the microstrip antennas is found. Finally, the structure parameters are optimized out, which reaches 44.67% impedance bandwidth. Furthermore, this kind of configuration can also be applied to the multi-layer patch antenna.

Finite Element Modeling and Design of Rectangular Patch Antenna with Different Feeding Techniques

The finite element modeling of three dimensional structures is important for researchers especially in the field of antennas and other domains of electromagnetic waves. This paper presents a finite element calculations and numerical analysis for the microstrip patch antennas. In this paper, two different designs have been modelled and analyzed and both designs are based on the rectangular patches. The feeding point of one design is inside the patch while the other design contains feeding point outside the patch is T shaped. The computational analysis showed some interesting results for radiation pattern and far field domain. For these designs, the characteristic impedance taken is 50 Ω and the operating frequency domain is 1.4 to 1.7 GHz. The microstrip patch antennas are encapsulated in the inert spherical atmosphere of 20 mm thickness containing air inside it.

Double U-Shaped Slots Loaded Stacked Patch Antenna for Multiband Operation

The design of a seven-band stacked patch antenna for the C, X and Ku band is presented. The antenna consists of an H-slot loaded fed patch, stacked with dual U-slot loaded rectangular patch to generate the seven frequency bands. The total size of the antenna is 39.25 × 29.25 mm2. The multiband stacked patch antenna is studied and designed using IE3D simulator. For verification of simulation results, the antenna is analyzed by circuit theory concept. The simulated return loss, radiation pattern and gain are presented. Simulated results show that the antenna can be designed to cover the frequency bands from (4.24 GHz to 4.50 GHz, 5.02 GHz to 5.25 GHz) in C-band application, (7.84 GHz to 8.23 GHz) in X-band and (12.16 GHz to 12.35 GHz, 14.25 GHz to 14.76 GHz, 15.25 GHz to 15.51 GHz, 17.52 GHz to 17.86 GHz) in Ku band applications. The bandwidths of each band of the proposed antenna are 5.9%, 4.5%, 4.83%, 2.36%, 3.53%, 1.68% and 1.91%. Similarly the gains of the proposed band are 2.80 dBi, 4.39 dBi, 4.54 dBi, 10.26 dBi, 8.36 dBi and 9.91 dBi, respectively.

Experimental Study of Stacked Rectangular Microstrip Antenna for Dual-Band

A dual-band characteristic of stacked rectangular microstrip antenna is experimentally studied. It is a probe fed antenna for impedance matching with 50Ω coaxial cable. This antenna works well in the frequency range (2.86 to 4.63 GHz). It is basically a low cost, light weight medium gain antenna, which is used for mobile communication. The variations of the length and width (1mm) of the stacked rectangular patch antenna have been done. And it is found dual resonance with increasing lower resonance frequency and almost constant upper resonance frequency with increases of the length & width of rectangular microstrip antenna. The input impedance and VSWR, return loss have been measured with the help of Network analyzer.

Tunnel Diode Loaded Microstrip Antenna with Parasitic Elements

The present work describes the circuit model based analysis of symmetrically tunnel diode loaded microstrip antenna with parasitic elements. To optimize the antenna characteristics, a systematic study has been carried out as a function of tunnel diode bias voltage, space between parasitic patch and fed patch. The results obtained from antenna radiation pattern depict that an improvement of 5.8 MHz in bandwidth can be achieved if the symmetrically tunnel diode is loaded with patch along with parasitic elements of gap (s) = 3.6 cm. It has also been noted that at this state the radiations are more powerful i.e. 0.5647 dB as compared to single patch design.

具有全向波束高增益的引信共形阵列天线

针对对地弹药引信天线不能满足宽落角探测需求的问题,提出一种基于共形阵列天线技术的宽波束产生方法,通过采用偶极子、微带天线阵列共形于引信风帽内腔表面,实现侧向全向辐射特性。该方法设计的天线可以随风帽的形状而改变,不占用其余空间。经测试验证表明该天线在H面具有全向辐射特性且增益较高。