无界域上具有记忆的非自治Plate方程随机吸引子的存在性

研究无界域上一类具有衰退记忆和加性噪声的非自治Plate方程解的长时间行为.利用一致估计验证了解的拉回渐近紧性,获得了其随机吸引子的存在性.

Effect of gradient temperature rolling process on promoting crack healing in Q500 heavy plates

To ensure the quality of heavy plate products as determined by ultrasonic inspection, it is necessary to effectively control defects such as cracks and shrinkage cavities in heavy plates. Generally, some defects such as large size cracks exist due to insufficient deformation in the center of traditionally rolled plates. Compared with the traditional rolling process, gradient temperature rolling(GTR) process can effectively increase deformation inside heavy plates. In this study, the effect of GTR on crack healing was analyzed through a comparison experiment with the uniform temperature rolling(UTR). The results show that the GTR process could increase the plastic strain inside the heavy plate and effectively promote the healing process of the preset cracks. The degrees of crack healing at the center and quarter thickness position of the steel plate via GTR were greater than twice those of the plate via UTR. The GTR process can significantly reduce the internal defects of heavy plates and improve the defect detection level of heavy plate products. Also, The GTR process results in the formation of new crystal grains in the crack region, which is crucial to crack healing.

A Study of Influencing Systems and Moisture Budget in a Heavy Rainfall in Low Latitude Plateau in China during Early Summer

Analysis of a heavy rainfall in a lower latitude plateau and characteristics of water vapor transportation have been conducted by using conventional data and denser surface data. The results show： （1） the heavy rainfall was caused by a series of mesoscale systems under favorable large-scale conditions when the warm moister air and cold air interacted with each other. At the same time, the coupling between the upper- and lower-level jets was revealed. It is also found that there exists some different characteristics among the main influencing systems of heavy rainfalls in Yunnan, such as the Indian-Myanmar trough and the path of the cold air, compared with those in East and South China. （2） The interaction between mesoscale convergence lines near the ground may be a possible triggering mechanism for the occurrence of mesoscale systems, and the dynamical and thermal dynamical structure of the mesoscale systems was very obvious. The convergence lines may relate closely to the terrain of Yunnan, China. （3） The computation of the water vapor budget reveals that the primary source of water vapor supply for heavy rainfall was in the Bay of Bengal. In this case, the water vapor could be transported into Yunnan even though the amount of water vapor was less than that in the lower troposphere in East and South China. In addition, the analysis for three-dimensional air parcel trajectories better revealed and described the source location and the transportation of water vapor to Yunnan.

FEM study on inflow strain in heavy plate during rolling

Heavy plate rolling processing in every single pass was simulated by the method of FEM. Distribution of the inflow strain on the specified path and related parameters （plate thickness H, pass reduction dH, rolling speed V） in the thickness direction of the plate center were studied. The results show that the plate thickness H and pass reduction dH have significant effects on the inflow strain on the specified path, while the rolling speed presents little effect. The relationships between the strain （PEEQ） and the plate thickness （H）/pass reduction （dH） were also established based on the simulation results.

The Upstream ＂Strong Signals＂ of the Water Vapor Transport over the Tibetan Plateau during a Heavy Rainfall Event in the Yangtze River Basin

A heavy rainfall event that occurred over the middle and lower reaches of the Yangtze River Basin （YRB） during July 11-13 2000 is explored in this study. The potential/stream function is used to analyze the upstream ＂strong signals＂ of the water vapor transport in the Tibetan Plateau （TP）. The studied time period covers from 2000 LST 5 July to 2000 LST 15 July （temporal resolution： 6 hours）. By analyzing the three-dimensional structure of the water vapor flux, vorticity and divergence prior to and during the heavy rainfall event, the upstream ＂strong signals＂ related to this heavy rainfall event are revealed. A strong correlation exists between the heavy rainfall event in the YRB and the convective clouds over the TE The ＂convergence zone＂ of the water vapor transport is also identified, based on correlation analysis of the water vapor flux two days and one day prior to, and on the day of, the heavy rainfall. And this ＂convergence zone＂ coincides with the migration of the maximum rainfall over the YRB. This specific coupled structure actually plays a key role in generating heavy rainfall over the YRB. The eastward movement of the coupled system with a divergence]convergence center of the potential function at the upper/lower level resembles the spatiotemporal evolution of the heavy rainfall event over the YRB. These upstream ＂strong signals＂ are clearly traced in this study through analyzing the three-dimensional structure of the potential/stream function of upstream water vapor transport.

Industrial practice of clad-rolling in heavy steel plate production

In this paper,a brief introduction on clad-rolling heavy steel plates of 90 mm and 140 mm thick is presented.The steel plates were hot rolled by 265mm slabs that are cladded by double 135mm continuous casting slabs of Q235 steel.After hot rolling,interface of the cladding slabs completely disappeared, revealing uniform grains similar to the rest of the materials.Ultrasonic tests were carried out on both steel plates,demonstrating excellent results.Through thickness tensile tests were also implemented on both steel plates,resulting in perfect mechanical properties complying with specific standards.The result proves that a minimum reduction rate of 1.89 is available in producing 140 mm thick steel plate with excellent through thickness properties.

Hydrodynamic Characteristics of Square Heaving Plates with Opening Under Forced Oscillation

The existence of the heaving plates can improve the heaving motion performance of an offshore structure significantly by providing both extra added mass and damping.In the current research,numerical investigation is carried out on the hydrodynamic characteristics of both isolated square heaving plate and double square heaving plates with opening by an immersed boundary-lattice Boltzmann method.The effects on hydrodynamic performance of plates due to Keulegan-Carpenter(KC)number,frequency number,opening ratio,opening distribution and spacing of plates are examined.It is found that the heaving plates with optimized opening ratio can provide additional damping compared with the plates without opening.Better hydrodynamic characteristics of double plates can be obtained with the increase of plate spacing.

Removal of heavy metals from artificial metals contaminated water samples based on micelle-templated silica modified with pyoverdin I

The micelle-templated silica （MTS） was firstly chemically modified with 3-glycidoxypropyl-trimethoxysilane （GPTMS） before immobilized with pyoverdin I. The characteristics of pyoverdin I-anchored onto the modified MTS were investigated using fluorescence, infrared spectra and scanning electron microscopy. The specific surface area of all materials was calculated by Branauer, Emmett and Teller （BET） method using nitrogen isotherm adsorption data. As the results, the surface area of commercial silica gel decreased from 609.2 to 405.4 m2/g, it indicated that the pyoverdin I could be immobilized onto the surface of silica solid support. This adsorbent was used for extraction of Fe（Ⅲ）, Cu（Ⅱ）, Zn（Ⅱ）, and Pb（Ⅱ） in artificial metals contaminated water. Experimental conditions for effective adsorption of trace levels of metal ions were optimized with respect to different experimental parameters using batch procedure. The optimum pH value for the removal of metal ions simultaneously on this adsorbent was 4.0. Complete desorption of the adsorbed metal ions from the adsorbent was carried out using 0.25 mol/L of EDTA. The effect of different cations and anions on the adsorption of these metals on adsorbent was studied and the results showed that the proposed adsorbent could be applied to the highly saline samples and the sample which contains some transition metals.

Conventional tillage improves the storage of soil organic carbon in heavy fractions in the Loess Plateau, China

Soil labile organic carbon （C） plays an important role in improving soil quality. The relatively stable fractions of soil organic C （SOC） represent the bulk of SOC, and are also the primary determinant of the long-term C balance of terrestrial ecosystems. Different land use types can influence the distribution patterns of different SOC fractions. However, the underlying mechanisms are not well understood. In the present study, different fractions of SOC were determined in two land use types： a grazed grassland （established on previously cultivated cropland 25 years ago, GG） and a long-term cultivated millet cropland （MC）. The results showed that C concentration and C storage of light fractions （LF） and heavy fractions （HF） presented different patterns along the soil profiles in the two sites. More plant residues in GG resulted in 91.9% higher LF storage at the 0-10 cm soil depth, further contributed to 21.9% higher SOC storage at this soil depth; SOC storage at 20-60 cm soil depth in MC was 98.8% higher than that in GG, which could be mainly attributed to the HF storage 104.5% higher than in GG. This might be caused by the long-term application of organic manure, as well as the protection from plough pan and silt- and clay-sized particles. The study indicated that different soil management practices in this region can greatly influence the variations of different SOC fractions, while the conventional tillage can greatly improve the storage of SOC by in- creasing heavy fractions.

Assessment of heavy metals in sediment in a heavily polluted urban river in the Chaohu Basin, China

The Nanfei River （Anhui Province, China） is a severely polluted urban river that flows into Chaohu Lake. In the present study, sediments were collected from the river and analyzed for their heavy metal contents. Multivariate statistics and the fuzzy comprehensive assessment method were used to determine the sources of pollution, the current pollution status, and spatial and temporal variations in heavy metal pollution in sediments. The concentrations of arsenic （As）, cadmium （Cd）, chromium （Cr）, copper （Cu）, mercury （Hg）, nickel （Ni）, lead （Pb）, and zinc （Zn） in sediments ranged from 5.67-113, 0.08-40.2, 41.6-524, 15.5-460, 0.03-4.84, 13.5-180, 18.8-250, and 47.9-1 996 mg/kg, and the average concentrations of each metal were 1.7, 38.7, 1.8, 5.5, l 8.8, 1.3, 2.5, and 11.1 times greater than the background values, respectively. Multivariate statistical analysis demonstrated that Hg, Cu, Cr, Cd, and Ni may have originated from industrial activities, whereas As and Pb came from agricultural activities. The fuzzy comprehensive assessment method, based on the fuzzy mathematics theory, was used to obtain a detailed assessment of the sediment quality in the Nanfei River watershed. The results indicated that the pollution was moderate in the downstream tributaries of the Nianbu and Dianbu Rivers, but was severe in the main channel of the Nanfei River and in the upstream tributaries of the Sill and Banqiao Rivers. Therefore, sediments in the Nanfei River watershed are heavily polluted and urgent measures should be taken to remedy the status.

Influence of proximity to the Qinghai-Tibet highway and railway on variations of soil heavy metal concentrations and bacterial community diversity on the Tibetan Plateau

An understanding of soil microbial communities is crucial in roadside soil environmental assessments.The 16S rRNA se quencing of a stressed microbial community in soil adjacent to the Qinghai-Tibet Highway(QTH)revealed that the accu mulation of heavy metals(over about 10 years)has affected the diversity of bacterial abundance and microbial community structure.The proximity of a sampling site to the QTH/Qinghai-Tibet Railway(QTR),which is effectively a measure of the density of human engineering,was the dominant factor influencing bacterial community diversity.The diversity of bacterial communities shows that 16S rRNA gene abundance decreased in relation to proximity to the QTH and QTR in both alpine wetland and meadow areas.The dominant phyla across all samples were Actinobacteria and Proteobacteria.The concentration of Cr and Cd in the soil were positively correlated with proximity to the QTH and QTR(MC/WC sam pling sites),and Ni,Co,and V were positively correlated with proximity to the QTH and QTR(MA/WA sampling sites).The results presented in this study provide an insight into the relationships among heavy metals and soil microbial commu nities,and have important implications for assessing and predicting the impacts of human-induced activities from the QTH and QTR in such an extreme and fragile environment.

Review of the last three years since the commissioning of Baosteel's 5m heavy plate plant and future outlook

Baosteel＇ s 5m heavy plate plant was successfully tested on March 1,2005. Since then,the Heavy Plate Plant of Baosteel （hereinafter referred to as ＂the plant＂ ） has been encouraging its employees to study and trace the advanced heavy plate technologies, trying to find out the rules of heavy plate production and its quality control. The plant has gradually mastered this modem heavy plate plant and ensured that Baosteel＇ s production of heavy plates grew year by year,with 1.41 Mt product put in storage in 2007. The plant has focused on developing new technologies and products, meanwhile enhancing its capacity. It has produced a series of plate products, which can be used in manufacturing ship hulls ,pipelines ,bridges ,buildings ,boilers and pressure vessels.

Study on the rolling process for thin HSLA heavy plates

Analyzed and studied the characters of high strength low alloy steel which contain Mo,Cr,Nb and Ni.etc.Following actual rolling,combining the feature of rolling mode,and exploiting the equipment advantage of 5 m Heavy Plate Mill,optimized the material design,heating temperature and rolling method, stabilized rolling process of thin alloyed steel,the quality index was advanced.

Tapered heavy reduction technology for plate mill

This paper describes the benefits, technical difficulties and disadvantages of the current heavy reduction solutions for plate production. For updated plate mills,this paper gives a better idea for the heavy reduction control in the rolling process. That is to keep the reduction amount constant in the front-end and back-end sections of the plate and to adopt tapered rolling with variable reduction in the middle section of the plate. This solution （ already applied for a patent） can not only fully utilize the capacity of the mill motors, but also prevent difficulties in plate biting caused by the conventional heavy reduction solutions with excessive draft. This technical solution has been implemented at the 5 m plate mill plant of Baosteel,and industrial tests have proved the feasibility of it. This paper presents and analyzes the industrial test data and proves that the tapered heavy reduction technology can reduce the number of rolling passes. In addition ,this paper looks forward to the future research in this area.

Development of high strength heavy plate A517Q for offshore platform rack

This paper introduces the research and development of high strength A517Q developed by Baosteel for platform rack,with micro-alloying adding suitable quenching and tempering process,trial thickness of 127 - 178 mm high-strength A517Q.The trial plate crossing thickness has a uniform mechanical properties, yield strength greater than 700 MPa,tensile strength than 790 MPa,the Charpy impact than 90 J at -40℃, aging impact than 69 J,has high strength and excellent low temperature impact toughness,While the plate has excellent resistance to crack tearing ability of low-temperature,NDT is less than -45℃.The Developing heavy plates had been used for manufacturing racks of 200-foot jack-up offshore platform,the performance meeting the requirements of the ABS,CCS classification societies.

Numerical simulation research of dimension variation in heavy plate during quenching and tempering process

The dimension variation of B610E steel during the quenching and tempering process was simulated by ABAQUS,the coefficient of heat transfer during quenching was verified by the buried thermocouple test and the trend of the dimension variation during the quenching process was also calculated by ABAQUS. It was shown by the comparison of simulated results and industrially measured results that only the simulation of thickness and width variation was accurate, while length variation needed further simulation. Besides, the dimension variation trend was identical with the measured results.

The effect of the continuous casting process on ultrasonically-tested defects in heavy plates

A plate＇s internal quality is very critical, especially for boilers and high-pressure vessels. The ultrasonic test （UT） is the main type of non-destructive flaw detection for heavy plates, which is important because one of the main reasons for plate defects is ultrasonic flaws. This study, based on Baosteel＇ s practical experience in the manufacture of heavy plates, elucidates the cause of defect formation by analyzing ultrasonic flaw testing maps and using special equipment, such as the scanning electron microscope, electron probe and the optical microscope. The author puts forward the following improvement measures： ① Ultrasonic flaws are caused by central porosity and segregation,[H] bubbles and inclusion in slabs.②Ultrasonic flaws are more likely to occur in the bottom and top of slabs rather than the other positions in the casting sequence. It is clear that one-quarter of the inner camber＇ s thickness is accumulated inclusion.③It is clear that overheating in the tundish and the flow of the casting mould have an effect on ultrasonic flaws caused by inclusions.④Soft reduction improves central porosity and segregation,which decreases the number of ultrasonic flaws in the plate.

A theory for three-dimensional response of micropolar plates

Through combined applications of the transfer-matrix method and asymptotic expansion technique,we formulate a theory to predict the three-dimensional response of micropolar plates.No ad hoc assumptions regarding through-thickness assumptions of the field variables are made,and the governing equations are two-dimensional,with the displacements and microrotations of the mid-plane as the unknowns.Once the deformation of the mid-plane is solved,a three-dimensional micropolar elastic field within the plate is generated,which is exact up to the second order except in the boundary region close to the plate edge.As an illustrative example,the bending of a clamped infinitely long plate caused by a uniformly distributed transverse force is analyzed and discussed in detail.

Climate Change Characteristics and Return Periods of Heavy Precipitation in the Northeast Side of Qinghai-Tibet Plateau

[ Objective] The study aimed to discuss analyze climate change characteristics and return periods of heavy precipitation in the northeast side of Qinghai-Tibet Plateau. [ Method] Based on the data of daily precipitation from 1943 to 2008 in 6 representative meteorological stations in Linxia located in the northeast side of Qinghai-Tibet Plateau, the climate change characteristics of heavy precipitation were analyzed, and the return periods of heavy precipitation were calculated by Pearson-Ill probability distribution method. [ Result] Days of heavy precipitation in Linxia region in- creased conspicuously since the 1990s. The return periods of heavy precipitation in the six stations on August 20, 2008 were consistent with the re- sults of artificial estimation. [ Conclusion] The research could provide scientific references for the reasonable utilization of climate resources, disas- ter prevention and rational arranqement of anricultural plantina svstems in Linxia reaion.

Impacts of Future Changes in Heavy Precipitation and Extreme Drought on the Economy over South China and Indochina

Heavy precipitation and extreme drought have caused severe economic losses over South China and Indochina(INCSC)in recent decades.Given the areas with large gross domestic product(GDP)in the INCSC region are distributed along the coastline and greatly affected by global warming,understanding the possible economic impacts induced by future changes in the maximum consecutive 5-day precipitation(RX5day)and the maximum consecutive dry days(CDD)is critical for adaptation planning in this region.Based on the latest data released by phase 6 of the Coupled Model Intercomparison Project(CMIP6),future projections of precipitation extremes with bias correction and their impacts on GDP over the INCSC region under the fossil-fueled development Shared Socioeconomic Pathway(SSP5-8.5)are investigated.Results indicate that RX5day will intensify robustly throughout the INCSC region,while CDD will lengthen in most regions under global warming.The changes in climate consistently dominate the effect on GDP over the INCSC region,rather than the change of GDP.If only considering the effect of climate change on GDP,the changes in precipitation extremes bring a larger impact on the economy in the future to the provinces of Hunan,Jiangxi,Fujian,Guangdong,and Hainan in South China,as well as the Malay Peninsula and southern Cambodia in Indochina.Thus,timely regional adaptation strategies are urgent for these regions.Moreover,from the sub-regional average viewpoint,over two thirds of CMIP6 models agree that maintaining a lower global warming level will reduce the economic impacts from heavy precipitation over the INCSC region.