3D printing of poly(ethyleneimine)-functionalized Mg-Al mixed metal oxide monoliths for direct air capture of CO_(2)

Direct air capture(DAC)of CO_(2)plays an indispensable role in achieving carbon-neutral goals as one of the key negative emission technologies.Since large air flows are required to capture the ultradilute CO_(2)from the air,lab-synthesized adsorbents in powder form may cause unacceptable gas pressure drops and poor heat and mass transfer efficiencies.A structured adsorbent is essential for the implementation of gas-solid contactors for cost-and energy-efficient DAC systems.In this study,efficient adsorbent poly(ethyleneimine)(PEI)-functionalized Mg-Al-CO_(3)layered double hydroxide(LDH)-derived mixed metal oxides(MMOs)are three-dimensional(3D)printed into monoliths for the first time with more than 90%adsorbent loadings.The printing process has been optimized by initially printing the LDH powder into monoliths followed by calcination into MMO monoliths.This structure exhibits a 32.7%higher specific surface area and a 46.1%higher pore volume,as compared to the direct printing of the MMO powder into a monolith.After impregnation of PEI,the monolith demonstrates a large adsorption capacity(1.82 mmol/g)and fast kinetics(0.7 mmol/g/h)using a CO_(2)feed gas at 400 ppm at 25℃,one of the highest values among the shaped DAC adsorbents.Smearing of the amino-polymers during the post-printing process affects the diffusion of CO_(2),resulting in slower adsorption kinetics of pre-impregnation monoliths compared to post-impregnation monoliths.The optimal PEI/MeOH ratio for the post-impregnation solution prevents pores clogging that would affect both adsorption capacity and kinetics.

Highly dispersed MgInCe-mixed metal oxides catalyzed direct carbonylation of glycerol and CO_(2)into glycerol carbonate

Glycerol carbonate,an important glycerol value-added product,has been widely used as an active intermediate and inert solvent in the synthesis of cosmetics,detergents,chemical intermediates,polymers,and so on.The direct carbonylation from glycerol with CO_(2)is considered a promising route,but still tough work due to the thermodynamic stability and the kinetic inertness of CO_(2).In this work,highlyselective direct carbonylation of glycerol and CO_(2)into glycerol carbonate has been achieved over highly dispersed MgInCe-mixed metal oxides(MgInCe-MMO),which were prepared through the topological transformation derived from the MgInCe-layered double hydroxides(MgInCe-LDHs).By precisely modulating the surface basic-acidic properties and the oxygen vacancies,an efficient carbonylation of glycerol with CO_(2)has been achieved with a selectivity of up to>99%to glycerol carbonate.Deep investigation into the synergistic catalysis of base-acid sites and oxygen vacancies has been clarified.

Synthesis and highly efficient photocatalytic activity of mixed oxides derived from ZnNiAl layered double hydroxides

ZnO/NiO/ZnAl2O4 mixed-metal oxides were successfully synthesized through a hydrotalcite-like precursor route, in which appropriate amounts of metal salts solutions were mixed to obtain a new series of ZnNiAl layered double hydroxides（LDHs） as precursors, followed by calcination under different temperatures. The as-obtained samples were characterized by SEM, HRTEM, TEM, XRD, BET, TG-DTA, and UV-Vis spectra techniques. The photocatalytic activities of the samples were evaluated by degradation of methyl orange（MO） under the simulated sunlight irradiation. The effects of Zn/Ni/Al mole ratio and calcination temperature on the composition, morphology and photocatalytic activity of the samples were investigated in detail. The results indicated that compared with ZnNiAl-LDHs, the mixed-metal oxide showed superior photocatalytic performance for the degradation of MO. A maximum of 97.3% photocatalytic decoloration rate within 60 min was achieved from the LDH with the Zn/Ni/Al mole ratio of 2：1：1 and the calcination temperature of 500 ℃, which much exceeded that of Degussa P25 under the same conditions. The possible mechanism of photocatalytic degradation over ZnO/NiO/ZnAl2O4 was discussed.

Catalytic reduction of SO_2 by CO over CeO_2-TiO_2 mixed oxides

The structure and catalytic desulfurization characteristics of CeO2-TiO2 mixed oxides were investigated by means ofX-ray diffraction （XRD）, X-ray photoelectron spectroscopy （XPS） and catalytic activity tests. According to the results, a CeO2-TiO2solid solution is formed when the mole ratio of cerium to titanium n（Ce）：n（Ti） is 5：5 or greater, and the most suitable n（Ce）：n（Ti） isdetermined as 7：3, over which the conversion rate of SO2 and the yield of sulfur at 500℃ reach 93% and 99%, respectively.According to the activity testing curve, Ce0.7Ti0.3O2 （n（Ce）：n（Ti）=7：3） without any pretreatment can be gradually activated by reagentgas after about 10 min, and reaches a steady activation status 60 min later. The XPS results of Ce0.7Ti0.3O2 after different time ofSO2＋CO reaction show that CeO2 is the active component that offers the redox couple Ce4＋/Ce3＋ and the labile oxygen vacancies, andTiO2 only functions as a catalyst structure stabilizer during the catalytic reaction process. After 48 h of catalytic reaction at 500℃,Ce0.7Ti0.3O2 still maintains a stable structure without being vulcanized, demonstrating its good anti-sulfur poisoning performance.

A rationale for the development of thermally stable nanostructured CeO_2-ZrO_2-containing mixed oxides

CeO2-ZeO2 solid solutions are extensively used as oxygen storage promoters in the current automotive three-way catalysts. High thermal stability of the textural properties is one of the most important requirements for practical application since temperatures up to 1273 K are easily experienced by these materials under real working conditions. In the present paper, we investigated how hydrothermal treatments applied to cakes of doped and undoped ZrO2-rich CeO2-ZrO2 precursors might improve the thermal stability of the final CeO2-ZrO2 solid solution. A rationale was developed that allowed to correlate the morphology of the hydrothermaUy treated cake with the thermal stability at 1273 K of the final product, which did not depend on the composition of the mixed oxides.

Catalytic performance for methane combustion of supported Mn-Ce mixed oxides

A series of supported Mn-Ce mixed oxide catalysts were prepared by the impregnation method and used for the oxidation of methane. The catalysts were characterized by N2 adsorption （BET）, X-ray diffraction （XRD）, laser Raman spectrum （LRS）, and temperature programmed reduction （TPR） techniques. The XRD and LRS results confirmed the high dispersion of active components or formation of solid solution between manganese and cerium oxides in the bulk and on the surface of mixed oxide catalysts. The reducibility was remarkably promoted by the stronger synergistic interaction between the two oxides from H2-TPR measurements. As expected, all the experimental mixed oxide catalysts showed excellent activity for methane combustion at low temperature. Especially, for the catalyst with Mn-Ce ratio 3：7, methane conversion reached 92% at a temperature as low as 470 ℃.

Effect of Manganese Doping on Oxygen Storage Capacity of Ceria-Zirconia Mixed Oxides

CeO2-ZrO2-MnOx mixed oxide series were prepared by sol-gel method. CO pulse and CO-O2 cycle measurements were carried out to examine the oxygen storage complete capacity （OSCC） and dynamic oxygen storage capacity （OSC） of the samples. The doping method brought about strong interactions between manganese oxide and ceria, both in the bulk and on the surface. Only a small part of Mn cations are incorporated into the ceria lattice to form solid solutions and the remaining are left on the surface as finely dispersed Mn3O4. The OSC behaviors of the materials are influenced by the doping amount of Mn and the solubility of Mn in the CeO2 lattice. The OSC is more easily affected by available contents of oxygen storage components when the measurement frequency is low. Comparatively, the concentration of lattice defects, which affects the mobility of bulk oxygen, is the determining factor under high frequency.

Recent advance on VOCs oxidation over layered double hydroxides derived mixed metal oxides

Catalytic oxidation is regarded as one of the most promising strategies for volatile organic compounds(VOCs)purification.Mixed metal oxides(MMOs),after topological transformation using layered double hydroxides(LDHs)as precursors,are extensively used as catalysts for VOCs oxidation due to their uniformity advantage.This review summarizes the developments in the LDH-derived VOCs heterogeneous catalytic oxidation over the last 10 years.Particularly,it addresses the VOCs abatement performance over MMO,noble metal/MMO,core-shell structured MMO,and integral MMO film catalysts originating from LDHs.Moreover,it highlights the water vapor effect and oxidation mechanism.This review indicates that LDH-based catalysts are a category of important VOCs oxidation materials.

Enhanced selective catalytic reduction of NO with NH3 via porous micro-spherical aggregates of Mn–Ce–Fe–Ti mixed oxide nanoparticles

We rationally designed a high performance denitration(De-NOx) catalyst based on a micrometer-sized spherical Mn–Ce–Fe–Ti(CP-SD)catalyst for selective catalytic reduction(SCR). This was prepared by a co-precipitation and spray drying(CP-SD) method. The catalyst was systematically characterized, and its morphological structure and surface properties were identified. Compare with conventional Mn–Ce–Fe–Ti(CP) catalysts, the Mn–Ce–Fe–Ti(CP-SD) catalyst had superior surface-adsorbed oxygen leading to enhanced 'fast NH3-SCR' reaction. The asobtained Mn–Ce–Fe–Ti(CP-SD) catalyst offered excellent NO conversion and N2 selectivity of 100.0% and 84.8% at 250℃, respectively, with a gas hourly space velocity(GHSV) of 40,000 h-1. The porous micro-spherical structure provides a larger surface area and more active sites to adsorb and activate the reaction gases. In addition, the uniform distribution and strong interaction of manganese, iron, cerium, and titanium oxide species improved H2O and SO2 resistance. The results showed that the Mn–Ce–Fe–Ti(CP-SD) catalyst could be used prospectively as a denitration(De-NOx) catalyst.

Properties of TiO_2-SiO_2 Mixed Oxides and Photocatalytic Oxidation of Heptane and Sulfur Dioxide

A series of TiO 2-XSiO 2[X denotes the molar fraction(%) of silica in the mixed oxides] with different \{n(Ti)\}/n(Si) ratios was prepared with ammonia water as a hydrolysis catalyst. The photocatalysts prepared were characterized by XRD, thermal analysis, FTIR, UV-Vis and SPS. The characterization results of FTIR and UV-Vis spectra show that Ti atoms were gradually changed from octahedral coordination to tetrahedral coordination with the addition of silica, which is not beneficial for obtaining strong Brnsted acidity and higher photocatalytic activity. The photocatalytic activity experiments, which were conducted by using heptane(or SO 2) as the model reactant, showed that TiO 2-SiO 2 containing a suitable amount of silica can exhibit much higher photocatalytic activity than pure TiO 2. The enhanced photocatalytic activity can be attributed to three following factors: (1) smaller crystalline size; (2) higher thermal stability; (3) the new strong Brnsted acidity.

Co–Cr–O mixed oxides for low–temperature total oxidation of propane: Structural effects, kinetics, and spectroscopic investigation

A series of Co–Cr–O mixed oxides with different Co/Cr molar ratios are synthesized and tested for the total oxidation of propane.The reaction behaviors are closely related to the structural features of the mixed oxides.The catalyst with a Co/Cr molar ratio of 1:2(1 Co2 Cr)and a spinel structure has the best activity(with a reaction rate of 1.38μmol g^–1 s^–1 at 250℃),which is attributed to the synergistic roles of its high surface acidity and good low-temperature reducibility,as evidenced by the temperature-programmed desorption of ammonia,reduction of hydrogen,and surface reaction of propane.Kinetic study shows that the reaction orders of propane and oxygen on the 1 Co2 Cr catalyst(0.58±0.03 and 0.34±0.05,respectively)are lower than those on the 2 Co1 Cr catalyst(0.77±0.02 and 0.98±0.16,respectively)and 1 Co5 Cr(0.66±0.05 and 1.30±0.11,respectively),indicating that the coverages of propane and oxygen on 1 Co2 Cr are higher than those on the other catalysts due to its higher surface acidity and higher reducibility.In addition,in-situ diffuse reflectance infrared spectroscopic investigation reveals that the main surface species on 1 Co2 Cr during the reaction are polydentate carbonate species,which accumulate on the surface at low temperatures(<250℃)but decompose at relatively high temperatures.

Preparation of Well Dispersed and Ultra-Fine Ce(Zr)O_2 Mixed Oxide by Mechanochemical Processing

Ultra-fine CeO_2-ZrO_2 mixed oxide was successfully synthesized by wet-solid phase mechanochemical processing, Ce_2(CO_3)_3·8H_2O, ZrOCl_2·xH_2O and ammonia were used as reactants. It is found that the crystalline Ce_2(CO_3)_3·8H_2O and ZrOCl_2·xH_2O are changed to amorphous cerium and zirconium hydroxide precursor after milling with ammonia, and Ce_(0.15)Zr_(0.85)O_2 mixed oxide with pure tetragonal phase structure and medium particle size(D_(50))less than 1μm is formed by calcining precursor over 673 K. The XRD patterns indicate that the crystal unite size increases with rising calcining temperature due to crystal growth. However, the particle size and BET surface area of the Ce(Zr)O_2 mixed oxide decreases with rising calcining temperature, which may be attributed to the contract of particles and the vanish of holes inside grains.

Ethylbenzene to styrene over ZrO_2-based mixed metal oxide catalysts with CO_2 as soft oxidant

ZrO2-based mixed metal oxide catalysts for the industrially important dehydrogenation process of ethylbenzene to styrene monomer have been explored by our group for the past 20 years.These efforts were subjected to the activation of CO2 over mixed metal oxide catalysts and resulted in several promising benefits to the dehydrogenation processes,such as stabilized conversion and selectivity,suppressed coke formation and commercially-acceptable longevity.In this review,we summarize the most recent developments on ZrO2-based mixed metal oxide catalysts,including the further optimization of sol-gel process in the synthesis of catalysts,rationalizing acid-base properties by doping,co-operative properties between redox and acid-base active sites and additional promoters towards the effective improvement of the longevity of catalysts.

Preparation and characterization of Cu-Ce-La mixed oxide as water-gas shift catalyst for fuel cells application

Cu-Ce-La mixed oxides were prepared by three precipitation methods （coprecipitation, homogeneous precipitation, and deposition precipitation） with variable precipitators and characterized using X-ray diffraction, BET, temperature-programmed reduction, and catalytic reaction for the water-gas shift. The Cu-Ce-La mixed oxide prepared by coprecipitation method with NaOH as precipitator presented the highest activity and thermal stability. Copper ion substituted quadrevalent ceria entered CeO2 （111） framework was in favor of activity and thermal stability of catalyst. The crystallinity of fresh catalysts increased with the reduction process. La^3＋ or Ce^4＋ substituted copper ion entered the CeO2 framework during reduction process. The coexistence of surface copper oxide （crystalline） and pure bulk crystalline copper oxide both contributed to the high activity and thermal stability of Cu-Ce-La mixes oxide catalyst.

Structure and Catalytic Behavior of CuO-ZrO-CeO_2 Mixed Oxides

The effect of doping CuO on the structure and properties of zirconia ceria mixed oxide was studied. The results show that addition of CuO decreases the reduction temperature of ceria, and stabilizes the cubic structure of mixed oxides, and enhances catalytic activity of CuO ZrO CeO 2 mixed oxides for CO oxidation. Increasing ceria content in the mixed oxides can enhance the catalytic activity, but some impurities such as sulfate make catalytic activity falling. There is little effect of calcination temperature on catalytic activities, implying that these catalysts are effective with good thermal stability.

Selective Oxidation of Isobutene over CsFeCoBiMnMoO_x Mixed Oxide Catalyst

Mixed oxide catalyst Cs0.1Fe2Co6BiMnMo12Ox was prepared by the coprecipitation method. Selective oxidation of isobutene was carried out in a fixed-bed reactor over Cs0.1Fe2Co6BiMnMo12Ox. The results showed that the catalyst had high catalytic activity. Under the optimum reaction conditions (n(i-C4=):n(O2)=1:2-1:4, space velocity=180 h-1, T=360℃), the yields of methacrolein and methacrylic acid can reach 80% and 8%, respectively. The total yield of liquid products (methacrolein, methacrylic acid and acetic acid) can reach about 90%.

Hydrothermal Synthesis and Structure of [CH3NH3]2[(VⅣO)2(VⅤO4)2]:A New Layered Mixed-valence Vanadium Oxide Incorporated with Organic Cations

A new layered mixed valence vanadium oxide, [CH 3NH 3] 2[(V ⅣO) 2(V ⅤO 4) 2], which contains interlamellar organic cations was prepared under hydrothermal conditions and its single crystal structure was determined. It crystallizes in a triclinic system with space group P 1, a =0 625 59(8) nm, b =0 639 84(9) nm, c =0 747 19(10) nm, α =78 718(2)°, β =80 099(2)°, γ =77 100(2). The compound contains mixed valence V 4+ /V 5+ vanadium oxide layers constructed from VO 4 tetrahedra, pairs of edge sharing VO 5 square pyramid and methylamine with protonated organic amines occupying the interlayer space.

Mixed phase sodium manganese oxide as cathode for enhanced aqueous zinc-ion storage

Aqueous zinc-ion batteries have been regarded as a promising alternative to large-scale energy storage, due to associated low-cost, improved safety and environmental friendliness. However, a high-performance cathode material for both rate capability and specific capacity is still a challenge. One kind of the more promising candidates are sodium manganese oxide(NMO) materials, although they suffer from individual issues and need to be further improved. Herein, we present a novel mixed phase NMO material composed of nearly equal amounts of Na(0.55)Mn2O4 and Na(0.7)MnO(2.05). The structured configuration with particle size of 200–500 nm is found to be beneficial towards improving the ion diffusion rate during the charge/discharge process. Compared with Na(0.7)MnO(2.05) and Na(0.55)Mn2O4, the mixed phase NMO demonstrates an enhanced rate capability and excellent long-term cycling stability with a capacity retention of 83% after 800 cycles. More importantly, the system also delivers an impressive energy density and power density, as 378 W·h·kg^-1 at 68.7 W·kg^-1, or 172 W·h·kg^-1 at 1705 W·kg^-1. The superior electrochemical performance is ascribed to the fast Zn^2+ diffusion rate because of a large ratio of capacitive contribution(63.9% at 0.9 m V·s^-1). Thus, the mixed phase route provides a novel strategy to enhance electrochemical performance, enabling mixed phase NMO as very promising material towards large-scale energy-storage applications.

Dehydrogenation of methylcyclohexane over Pt supported on Mg–Al mixed oxides catalyst:The effect of promoter Ir

To enhance the hydrogen release during hydrogen storage,several Pt-Ir supported on Mg-Al mixed oxide catalysts were prepared and then applied into the dehydrogenation of methylcyclohexane(MCH)in this study.The effects of iridium content,reduction temperature on the activity and stability of the catalysts were studied in detail.In the presence of Ir,metal particle size was decrea sed and electron transfer between Ir and Pt was observed.High reduction temperature increased the metallic Ir content but enlarged the particle size of active site s.During the dehydrogenation reaction on Pt-Ir bimetallic catalyst,MCH was efficiently converted into toluene and PtIr-5/Mg-Al-275 exhibited the highe st activity.After prolonging the residence time and raising the reaction temperature to 350℃the conversion and hydrogen evolution rate were increased to 99.9%and 578.7 mmol·(g Pt)^-1·min^-1,respectively.Moreover,no carbon deposition was observed in the spent catalyst,presenting a high anti-coking ability and good potential for industrial application.

Highly Dispersed Pd Nanoparticles Supported on Zr-Doped MgAl Mixed Metal Oxides for 2-Ethylanthraquinone Hydrogenation

In this study,Pd-Mg(Al)-LDH/γ-Al2O3 and Pd-Mg(Al)Zr-LDH/γ-Al2O3 precursors were synthesized by impregnating Na2PdCl4 on Mg(Al)-LDH/γ-Al2O3 and Mg(Al)Zr-LDH/γ-Al2O3,and then the precursors were calcinated and reduced to obtain Pd-Mg(Al)-MMO/γ-Al2O3 and Pd-Mg(Al)Zr-MMO/γ-Al2O3 catalysts.Compared with Pd/γ-Al2O3 catalyst,the hydrogenation efficiency of Pd-Mg(Al)-MMO/γ-Al2O3 and Pd-Mg(Al)Zr-MMO/γ-Al2O3 increased by 15.7%and 24.0%,respectively.Moreover,the stability of Pd-Mg(Al)Zr-MMO/γ-Al2O3 catalyst was also higher than that of Pd/γ-Al2O3.After four runs,the hydrogenation efficiency of Pd/γ-Al2O3 decreased from 12.1 to 10.0 g/L,while that of Pd-Mg(Al)Zr-MMO/γ-Al2O3 decreased from 15.0 to 14.3 g/L.The active aquinones selectivities of all catalysts were almost 99%.The structures of the catalysts were characterized by X-ray diffraction(XRD),scanning electron microscopy(SEM),N2 adsorption–desorption,inductively coupled plasma-atomic emission spectrometry(ICP-AES),CO chemisorption analysis,transmission electron microscopy(TEM),temperature-programmed reduction with hydrogen(H2-TPR),and X-ray photoelectron spectroscopy(XPS).The results indicate that the improved catalytic performance is attributed to the stronger interaction between Pd and Mg(Al)Zr-MMO/γ-Al2O3,smaller Pd particle size and higher Pd dispersion.This work develops an effective method to synthesize highly dispersed Pd nanoparticles based on the layered double hydroxides(LDHs)precursor.