The oxidation behavior of 0. 8% La2O3- Mo5Si3/MoSi2 composites at 1200℃ in air was investigated. The results reveal that the oxidation resistance of the material with 0. 8% La2O3 and Mo5Si3 is impaired. The oxidation...The oxidation behavior of 0. 8% La2O3- Mo5Si3/MoSi2 composites at 1200℃ in air was investigated. The results reveal that the oxidation resistance of the material with 0. 8% La2O3 and Mo5Si3 is impaired. The oxidation resistance is decreased with increasing Mo5Si3 content. The mass loss follows a linear law in the initial oxidation. With oxidation time prolonging, a continuous and dense oxidation scale prevents oxygen from diffusing increasing when and leads to mass change a Mo5Si3 content is less than 30%. However, the composite shows ＂PEST＂ with the addition of 40% Mo5Si3. With increasing Mo5Si3 content, the oxidation resistance of 0.8% La2O3- Mo5Si3/MoSi2 decreases. This attributes to the poor oxidation resistance of M05Si3 and the relative density decreasing of 0. 8% La2O3-Mo5Si3/MoSi2 composite.展开更多
Ti-Ni-Mo-Si composite coating was fabricated on mild steel by reactive braze coating process with Ti61. 9Ni24. 6Si4. 411409.1 （ wt. % ） powders as the raw materials. Microstr^cture of the coating was characterized b...Ti-Ni-Mo-Si composite coating was fabricated on mild steel by reactive braze coating process with Ti61. 9Ni24. 6Si4. 411409.1 （ wt. % ） powders as the raw materials. Microstr^cture of the coating was characterized by optical microscopy, scanning electron microscopy, X-ray diffraction and energy dispersive spectroscopy and micro-hardness tester. Results indicate that the Ti-Ni-Mo-Si composite coating is metallurgically bonded to the mild steel substrate and has high hardness. The microstructure of the coating consists of the reinforcement of Ti5 Si3 and Mo9 Ti4 particles and the matrix of eutectic NiTi2. Due to the poor wettability of NiTi2 liquid at low temperature, TisSi3 and Mo9 Ti4 do not uniformly distribute in the NiTi2 matrix.展开更多
In the present paper,MoSi2(Cr5Si3)–RSiC composites were prepared via a combination of precursor impregnation pyrolysis(PIP) and MoSi2-Si-Cr alloy active melt infiltration(AAMI) process. Composition, microstructure, m...In the present paper,MoSi2(Cr5Si3)–RSiC composites were prepared via a combination of precursor impregnation pyrolysis(PIP) and MoSi2-Si-Cr alloy active melt infiltration(AAMI) process. Composition, microstructure, mechanical retention characteristics, and oxidation behaviors of the composites at elevated temperature were studied. X-ray diffraction(XRD) pattern confirms that the composites mainly compose of 6 H–SiC, hexagonal MoSi2, and tetragonal Cr5Si3. Scanning electron microscopy(SEM) image reveals that nearly denseMoSi2(Cr5Si3)–RSiC composites exhibiting three-dimensionally(3D) interpenetrated network structure are obtained when infiltrated at 2173 K, and the interface combination of the composites mainly depends on the composition ratio of infiltrated phases. Oxidation weight gain rate of the composites is much lower than that of RSiC matrix, where MoSiCr2 possesses the lowest value of 0.1630 mg×cm-2, about 78% lower than that of RSiC after oxidation at 1773 K for 100 h. Also, it possesses the highest mechanical values of 139.54 MPa(flexural strength σf and RT) and 276.77 GPa(elastic modulus Ef and RT), improvement of 73.73% and 29.77% as compared with that of RSiC, respectively. Mechanical properties of the composites increase first and then decrease with the extension of oxidation time at 1773 K, due to the cooperation effect of surface defect reduction via oxidation reaction and thermal stress relaxation in the composites, crystal growth, and thickness increase of the oxide film. Fracture toughness of MoSiCr2 reaches 2.24 MPa·m1/2(1673 K), showing the highest improvement of 31.70% as compared to the RT value.展开更多
文摘The oxidation behavior of 0. 8% La2O3- Mo5Si3/MoSi2 composites at 1200℃ in air was investigated. The results reveal that the oxidation resistance of the material with 0. 8% La2O3 and Mo5Si3 is impaired. The oxidation resistance is decreased with increasing Mo5Si3 content. The mass loss follows a linear law in the initial oxidation. With oxidation time prolonging, a continuous and dense oxidation scale prevents oxygen from diffusing increasing when and leads to mass change a Mo5Si3 content is less than 30%. However, the composite shows ＂PEST＂ with the addition of 40% Mo5Si3. With increasing Mo5Si3 content, the oxidation resistance of 0.8% La2O3- Mo5Si3/MoSi2 decreases. This attributes to the poor oxidation resistance of M05Si3 and the relative density decreasing of 0. 8% La2O3-Mo5Si3/MoSi2 composite.
文摘Ti-Ni-Mo-Si composite coating was fabricated on mild steel by reactive braze coating process with Ti61. 9Ni24. 6Si4. 411409.1 （ wt. % ） powders as the raw materials. Microstr^cture of the coating was characterized by optical microscopy, scanning electron microscopy, X-ray diffraction and energy dispersive spectroscopy and micro-hardness tester. Results indicate that the Ti-Ni-Mo-Si composite coating is metallurgically bonded to the mild steel substrate and has high hardness. The microstructure of the coating consists of the reinforcement of Ti5 Si3 and Mo9 Ti4 particles and the matrix of eutectic NiTi2. Due to the poor wettability of NiTi2 liquid at low temperature, TisSi3 and Mo9 Ti4 do not uniformly distribute in the NiTi2 matrix.
基金supported by the National Natural Science Foundation of China (Grant Nos. 51372078 and 51302076)Natural Science Foundation of Hunan Province of China (Grant No. 12JJ4054)+2 种基金Natural Science Foundation of Hunan Province (Grant No. 2018JJ4011)Jiangsu Province Innovative Talent Plan 2016, ChinaYancheng City 515 Talent Plan, China
文摘In the present paper,MoSi2(Cr5Si3)–RSiC composites were prepared via a combination of precursor impregnation pyrolysis(PIP) and MoSi2-Si-Cr alloy active melt infiltration(AAMI) process. Composition, microstructure, mechanical retention characteristics, and oxidation behaviors of the composites at elevated temperature were studied. X-ray diffraction(XRD) pattern confirms that the composites mainly compose of 6 H–SiC, hexagonal MoSi2, and tetragonal Cr5Si3. Scanning electron microscopy(SEM) image reveals that nearly denseMoSi2(Cr5Si3)–RSiC composites exhibiting three-dimensionally(3D) interpenetrated network structure are obtained when infiltrated at 2173 K, and the interface combination of the composites mainly depends on the composition ratio of infiltrated phases. Oxidation weight gain rate of the composites is much lower than that of RSiC matrix, where MoSiCr2 possesses the lowest value of 0.1630 mg×cm-2, about 78% lower than that of RSiC after oxidation at 1773 K for 100 h. Also, it possesses the highest mechanical values of 139.54 MPa(flexural strength σf and RT) and 276.77 GPa(elastic modulus Ef and RT), improvement of 73.73% and 29.77% as compared with that of RSiC, respectively. Mechanical properties of the composites increase first and then decrease with the extension of oxidation time at 1773 K, due to the cooperation effect of surface defect reduction via oxidation reaction and thermal stress relaxation in the composites, crystal growth, and thickness increase of the oxide film. Fracture toughness of MoSiCr2 reaches 2.24 MPa·m1/2(1673 K), showing the highest improvement of 31.70% as compared to the RT value.
