Assessing the Impact of Fugitive Dust Emissions from Cement Silos at Cluster of Concrete Batching Facilities Using Air Dispersion Modeling

This research assessed the environmental impact of cement silos emission on the existing concrete batching facilities in M35-Mussafah, Abu Dhabi, United Arab Emirates. These assessments were conducted using an air quality dispersion model (AERMOD) to predict the ambient concentration of Portland Cement particulate matter less than 10 microns (PM10) emitted to the atmosphere during loading and unloading activities from 176 silos located in 25 concrete batching facilities. AERMOD was applied to simulate and describe the dispersion of PM10 released from the cement silos into the air. Simulations were carried out for PM10 emissions on controlled and uncontrolled cement silos scenarios. Results showed an incremental negative impact on air quality and public health from uncontrolled silos emissions and estimated that the uncontrolled PM10 emission sources contribute to air pollution by 528958.32 kg/Year. The modeling comparison between the controlled and uncontrolled silos shows that the highest annual average concentration from controlled cement silos is 0.065 μg/m3, and the highest daily emission value is 0.6 μg/m3;both values are negligible and will not lead to significant air quality impact in the entire study domain. However, the uncontrolled cement silos’ highest annual average concentration value is 328.08 μg/m3. The highest daily emission average value was 1250.09 μg/m3;this might cause a significant air pollution quality impact and health effects on the public and workers. The short-term and long-term average PM10 pollutant concentrations at these receptors predicted by the air dispersion model are discussed for both scenarios and compared with local and international air quality standards and guidelines.

A distributed algorithm for signal coordination of multiple agents with embedded platoon dispersion model

In order to reduce average arterial vehicle delay, a novel distributed and coordinated traffic control algorithm is developed using the multiple agent system and the reinforce learning （RL）. The RL is used to minimize average delay of arterial vehicles by training the interaction ability between agents and exterior environments. The Robertson platoon dispersion model is embedded in the RL algorithm to precisely predict platoon movements on arteries and then the reward function is developed based on the dispersion model and delay equations cited by HCM2000. The performance of the algorithm is evaluated in a Matlab environment and comparisons between the algorithm and the conventional coordination algorithm are conducted in three different traffic load scenarios. Results show that the proposed algorithm outperforms the conventional algorithm in all the scenarios. Moreover, with the increase in saturation degree, the performance is improved more significantly. The results verify the feasibility and efficiency of the established algorithm.

Comparison between the Chinese EIA Guidelines for Air Dispersion Modelling and the Advanced Air Dispersion Model ADMS

This paper makes comparisons between Chinese Environmental Impact Assessment (EIA) Guidelines for Air dispersion modelling and the advanced air dispersion model ADMS. Since 2001 the ADMS model has been the first and only foreign model that has been approved by the Appraisal Center for Environment and Engineering (ACEE) to be used in EIA projects in China (http://www.china-eia. com/inden_content/rjrz/ rjrz_ADMS/htm). In the paper the following sections provide brief descriptions of the main features of the Chinese Guidelines for Air Dispersion (Section 2) and ADMS (Section 3); Section 4 provides a comparison of the two modelling methods for some simple cases and conclusions and discussion are given in Section 5.

Using the OSPM Model on Pollutant Dispersion in an Urban Street Canyon

An observational campaign was conducted in the street canyon of Zhujiang Road in Nanjing city in 2007. Hourly mean concentrations of PM10 were measured at street and roof levels. The Operational Street Pollution Model （OSPM） street canyon dispersion model was used to calculate the street concentrations and the results were compared with the measurements. The results show that there is good agreement between measured and predicted concentrations. The correlation coefficient R2 values （R2 is a measure of the correlation of the predicted and measured time series of concentrations） are 0.5319, 0.8044, and 0.6630 for the scatter plots of PM10 corresponding to light wind speed conditions, higher wind speed conditions, and all wind speed conditions, respectively. PM10 concentrations tend to be smaller for the higher wind speed cases and decrease rapidly with increasing wind speed. The presentations of measured and modelled concentration dependence on wind direction show fairly good agreement. PM10 concentrations measured on the windward side are relatively smaller, compared with the corresponding results for the leeward side. This study demonstrates that it is possible to use the OSPM to model PM10 dispersion rules for an urban street canyon.

An Axial Dispersion Model for Evaporating Bubble Column Reactor

Evaporating bubble column reactor (EBCR) is a kind of aerated reactor in which the reaction heat is removed by the evaporation of volatile reaction mixture. In this paper, a mathematical model that accounts for the gas-liquid exothermic reaction and axial dispersions of both gas and liquid phase is employed to study the performance of EBCR for the process of p-xylene(PX) oxidation. The computational results show that there are remarkable concentration and temperature gradients in EBCR for high ratio of height to diameter (H/DT). The temperature is lower at the bottom of column and higher at the top, due to rapid evaporation induced by the feed gas near the bottom. The concentration profiles in the gas phase are more nonuniform than those (except PX) in the liquid phase, which causes more solvent burning consumption at high H/DT ratio. For p-xylene oxidation, theo ptimal H/DT is around 5.

Modeling on Residence Time Distribution in Subsurface Flow Constructed Wetlands by Multi Flow Dispersion Model

As an important design factor for constructed wetlands,hydraulic retention time and its distribution will affect the treatment performance.Instantaneously injected sodium chloride tracers were used to obtain residence time distributions of the lab scale subsurface flow constructed wetland.Considering the presence of trailing and multiple peaks of the tracer breakthrough curve,the multi flow dispersion model(MFDM)was used to fit the experimental tracer breakthrough curves.According to the residual sum of squares and comparison between the experimental values and simulated values of the tracer concentration,MFDM could fit the residence time distribution(RTD)curve satisfactorily,the results of which also reflected the layered structure of wetland cells,thus to give reference for application of MFDM to the same kind of subsurface flow constructed wetlands.

Unified Data Model of Urban Air Pollution Dispersion and 3D Spatial City Model:Groundwork Assessment towards Sustainable Urban Development for Malaysia

Understanding the behavior of urban air pollution is important en route for sustainable urban development (SUD). Malaysia is on its mission to be a developed country by year 2020 comprehends dealing with air pollution is one of the indicators headed towards it. At present monitoring and managing air pollution in urban areas encompasses sophisticated air quality modeling and data acquisition. However, rapid developments in major cities cause difficulties in acquiring the city geometries. The existing method in acquiring city geometries data via ground or space measurement inspection such as field survey, photogrammetry, laser scanning, remote sensing or using architectural plans appears not to be practical because of its cost and efforts. Moreover, air monitoring stations deployed are intended for regional to global scale model whereby it is not accurate for urban areas with typical resolution of less than 2 km. Furthermore in urban areas, the pollutant dispersion movements are trapped between buildings initiating it to move vertically causing visualization complications which imply the limitations of existing visualization scheme that is based on two-dimensional (2D) framework. Therefore this paper aims is to perform groundwork assessment and discuss on the current scenario in Malaysia in the aspect of current policies towards SUD, air quality monitoring stations, scale model and detail discussion on air pollution dispersion model used called the Operational Street Pollution Model (OSPM). This research proposed the implementation of three-dimensional (3D) spatial city model as a new physical data input for OSPM. The five Level of Details (LOD) of 3D spatial city model shows the scale applicability for the dispersion model implementtation. Subsequently 3D spatial city model data commonly available on the web, by having a unified data model shows the advantages in easy data acquisition, 3D visualization of air pollution dispersion and improves visual analysis of air quality monitoring in urban areas.

Plug-flow/dispersion model of longitudinal dispersion

A modified Fickian plug-flow/dispersion model (P/D model) is developed in this study. In P/D model, the flow process is divided into two belts, plug flow belt and dispersion belt. P/D model is very similar to Fickian model and rather perfect. The prediction by P/D model can be always consistent with experimental data in river, flume, and pond, even though the data are much skew. Therefore, P/D model is better than Fickian model and other dispersion models.

Study of LPG Release & Dispersion Model

The current applicable release & dispersion models are reviewed. A typical model is developed on the basis of LPG storage conditions in China and the authors' research. The study is focused on the relationship between LPG composition and release rate, and on the influence of buildings or structures located in the surrounding area on the dispersion of gas plume. The established model is compared with existing models by the use of published field test data.

Odour Impact Assessment by Means of Dispersion Modeling, Dynamic Olfactometry and Mobile Electronic Nose around Agadir Fishing Port in Morocco

Odorous emissions emitted from various sources including industrial and commercial activities have particular concerns about human health. These malodors emissions are an environmental concern that affects health status and social life of the neighbors. That requires the local authority to set up a management strategy to control this nuisance. The evaluation of odour emissions from fishing port is complex because these emissions depend on several factors such as multiple sources of odor emissions, meteorological conditions, topography and others. That imposes the use of complementary approaches to monitor odours. In this paper, the case of Agadir fishing port is studied, which is adjacent to the tourist area and residential neighborhoods and which hosts a number of points that can generate odors. To assess this odour impact, three methods are used such as dynamic olfactometry, dispersion modeling and mobile electronic nose (e-nose). The use of these three methods in a complementary manner to assess odour impacts around a fishing port allowed both the quantification of the emissions using dynamic olfactometry and the evaluation of their impact on the study area with model dispersion. The results enabled also to identify the most affected areas of the city by odor emissions and to recognize the meteorological parameters maximizing odor impact. The other goal of this work is to compare the results of the odour dispersion modeling and e-nose measurements for one year in terms of frequency of overtaking the set alert thresholds over the same period. Comparison highlights the strengths and weaknesses of both approaches. Modeling can be used predicatively but it does not take into account fugitive emissions reliably in the absence of data on these emissions, modeling based on the hourly average misjudges the odor peaks, while e-nose made it possible to obtain validated data and provides accurate, affordable and real-time odour measurement capability tacking in to account the role of human perception without being able to characterize the extent of the odor nuisance caused by each source. We conclude that these three valuation methods provide complementary information about odor nuisance and reasonable estimates of odors.

A Method for Constructing Mathematical Modeling of the Spread of a New Crown Pneumonia Epidemic Based on the Effect of Temperature

To better predict the spread of the COVID-19 outbreak, mathematical modeling and analysis of the spread of the COVID-19 outbreak is proposed based on data analysis and infectious disease theory. Firstly, the mathematical model indicators of the spread of the new coronavirus pneumonia epidemic are determined by combining the theory of infectious diseases, the basic assumptions of the spread model of the new coronavirus pneumonia epidemic are given based on the theory of data analysis model, the spread rate of the new coronavirus pneumonia epidemic is calculated by combining the results of the assumptions, and the spread rate of the epidemic is inverted to push back into the assumptions to complete the construction of the mathematical modeling of the diffusion. Relevant data at different times were collected and imported into the model to obtain the spread data of the new coronavirus pneumonia epidemic, and the results were analyzed and reflected. The model considers the disease spread rate as the dependent variable of temperature, and analyzes and verifies the spread of outbreaks over time under real temperature changes. Comparison with real results shows that the model developed in this paper is more in line with the real disease spreading situation under specific circumstances. It is hoped that the accurate prediction of the epidemic spread can provide relevant help for the effective containment of the epidemic spread.

Cumulative Air Quality Impacts from Twenty-Two Major Power Plants

Cumulative assessment is a tool for the project developer to try and take into consideration not only their contribution to cumulative impacts but also other projects and external factors that may place their developments at risk.This study assessed the cumulative impacts of air emissions from 22 major power plants in southeast Bangladesh planned to generate 21,550 MW of electricity.It also includes anticipated growth in small to medium size industries,brickfields,highway traffic,inland water transport,transhippers,jetty,and vessel transports used for transporting fuel resources for these power plants.A 50 km by 50 km airshed is considered for air quality modeling.Cumulative analysis indicates that predicted MGLCs(Maximum Ground Level Concentrations)of NO2 and CO are complying with both Bangladesh NAAQS(National Ambient Air Quality Standards)and WBG(World Bank Group)Guidelines.The daily average MGLC of PM_(2.5)(62.45µg/m^(3))from all sources complies with NAAQS,however,exceeds the WBG Guidelines.Annual PM_(2.5) concentration(15.45µg/m^(3))exceeds NAAQS and WBG Guidelines.The PM10 concentration complies with the NAAQS for both 24-hour and annual averaging times.Annual average concentration(23.12µg/m^(3))exceeds WBG Guidelines.Daily average SO2 concentration(102.49µg/m^(3))complies with the NAAQS however,it exceeds the WBG guideline values.High concentrations of PM_(2.5) and SO2 are due to the contribution of transboundary emissions and secondary pollutants in the atmosphere.This dispersion modeling outcome can be used by the policymakers for the pollution reduction strategy.

Dust dispersion and management in underground mining faces

Presence of fine dust in air causes serious health hazard for mine operators resulting in such serious problems as coal workers’pneumoconiosis and silicosis.Major sources of dust appear of course along the mining face where the minerals are extracted.Proper control and management are required to ensure safe working environment in the mine.Here,we utilize the computational fluid dynamic(CFD)approach to evaluate various methods used for mitigating dust dispersion from the mining face and for ensuring safe level of dust concentration in the mine tunnel for safety of the operators.The methods used include:application of blowing and exhaust fans,application of brattice and combination of both.The results suggest that among the examined methods,implementation of appropriately located brattice to direct the flow from the main shaft to the mining face is the most effective method to direct dust particles away from the mining face.

Using ADMS models for Air Quality Assessment and Management in China

ADMS-Urban is the most widely used advanced dispersion model for urban areas, being used extensively in China and worldwide, providing a practical tool for assessing and managing urban air quality. In this paper we briefly describe the ADMS dispersion models and give an overview of their use in China. And it describes in more detail the use of ADMS-Urban in Fushun in Liaoning province and in Jinan in Shangdong province respectively, for studies of urban air quality. Finally the conclusions are presented.

Hydrodynamics and Lateral Gas Dispersion in a High-Density Circulating Fluidized Bed Reactor with Bluff Internals

Effect of bluff internals on the hydrodynamics and lateral gas mixing was studied in a 0.186m ID high-density riser. With the bluff internals, the extremely non-uniform radial profiles of solid fraction and particle velocity become flat and the dense downflow layer near the wall disappears, indicating the significant enhancement of solid turbulence introduced by the internals. The fluctuation velocity and solid fraction transient signal analysis indicates a significant increase in fluctuation intensity near the wall region. The length influenced by the internals on the flow structure is about 1 meter. The lateral gas dispersion coefficient increases significantly as the bluff internals exist in the riser.

Application of the ISCST3 model for predicting PCDD/F concentrations in agricultural soil in the vicinity of a MSWI plant in China

Based on the Industrial Source Complex Short-Term Version 3 （ISCST3） model, a simplified modeling approach was developed to predict concentrations of congeners of polychlorinated-p-dioxins and dibenzofurans （PCDD/Fs） of agricultural soil, within a radius of 3 kin from a municipal solid waste incinerator （MSWI） plant after its 4-year operation in Hangzhou, China. Comparisons were made between the measured and estimated congener-specific concentrations and the international-toxic equivalent （I-TEQ） values of soil samples with respect to distance from the stack. The results indicate that the predictions of soil PCDD/F concentrations and K-TEQ values were generally lower than their observations, and that the higher the degree of underestimation seems, the greater the further downwind one gets. Nevertheless, most of the predictions were in good agreement with the trend of measured ones and were within a factor of ten for samples located within 1 kin of the plant. Besides, analysis of contributions of various deposition pathways confirms that in addition to wet particle deposition, the dry gaseous deposition is essential for realistic prediction of PCDD/F depositions to soil, especially for tetra- and penta-chlorinated dioxins.

On the time development of dispersion in electroosmotic flow througha rectangular channel

This is an analytical study on the time develop- ment of hydrodynamic dispersion of an inert species in elec- troosmotic flow through a rectangular channel. The objec- tive is to determine how the channel side walls may affect the dispersion coefficient at different instants of time. To this end, the generalized dispersion model, which is valid for short and long times, is employed in the present study. An- alytical expressions are derived for the convection and dis- persion coefficients as functions of time, the aspect ratio of the channel, and the Debye-Htickel parameter representing the thickness of the electric double layer. For transport in a channel of large aspect ratio, the dispersion may undergo several stages of transience. The initial, fast time develop- ment is controlled by molecular diffusion across the narrow channel height, while the later, slower time development is governed by diffusion across the wider channel breadth. For a sufficiently large aspect ratio, there can be an interlude between these two periods during which the coefficient is nearly steady, signifying the resemblance of the transport to that in a parallel-plate channel. Given a sufficiently long time, the dispersion coefficient will reach a fully-developed steady value that may be several times higher than that with- out the side wall effects. The time scales for these periods of transience are identified in this paper.

Space Observations and Global Climatic Data Reanalysis in AERMOD Modeling Package to Enhance the Industrial Air Pollution and Health Risk Assessment

We try to enhance the AERMOD industrial pollution dispersion model with remote sensing observations and climatic models based on them. In this paper, we focus on surface parameters (albedo, roughness, Bowen ratio) and land use classification on which they depend. We model maximum hourly concentrations and the resulting acute health risk and assess the effect on them produced by using remote sensing data for local areas around industrial plants instead of global standard AERMOD parameters. We consider five real multi-source plants for the effect of classification and two of them for the effect of surface parameters. The effect on the critical pollutant is measured in three ways: a) as difference between the yearly maxima of hourly concentrations of a critical pollutant (“absolute”);b) the same limited to daytime workhours and 95% quantile instead of absolute maximum (“regulatory”);c) as maximum hourly difference over a year (“instant”). The measure of effect is divided either by the reference concentration of the pollutant, which yields the impact on health risk, or by the concentration obtained with AERMOD standards, which yields relative measure of impact. For a), the impact of roughness dominates, that of albedo is small and that of the Bowen ratio is almost zero. For b), the impact of roughness is less prominent, and that of albedo and Bowen ratio is noticeable. For c), the impact is considerable for all three parameters. The effect of land use classification is considerable in all three cases a) - c). We provide the figures for different measures of remote sensing data effect and discuss the perspective of using remote sensing data in regulatory context.

Viscoelastic modeling of the diffusion of polymeric pollutants injected into a pipe flow

This study focuses on the transient analysis of nonlinear dispersion of a polymeric pollutant ejected by an external source into a laminar pipe flow of a Newtonian liquid under axi-symmetric conditions.The influence of density variation with pollutant concentration is approximated according to the Boussinesq approximation and the nonlinear governing equations of momentum,pollutant concentration are obtained together with and Oldroyd-B constitutive model for the polymer stress.The problem is solved numerically using a semi-implicit finite difference method.Solutions are presented in graphical form for various parameter values and given in terms of fluid velocity,pollutant concentration,polymer stress components,skin friction and wall mass transfer rate.The model can be a useful tool in understanding the dynamics of industrial pollution situations arising from improper discharge of hydrocarbon pollutants into,say,water bodies.The model can also be quite useful for available necessary early warning methods for detecting or predicting the scale of pollution and hence help mitigate related damage downstream by earlier instituting relevant decontamination measures.

Improving modeling of low-altitude particulate matter emission and dispersion:A cotton gin case study

Monitoring and modeling of airborne particulate matter(PM)from low-altitude sources is becoming an important regulatory target as the adverse health consequences of PM become better understood.However,application of models not specifically designed for simulation of PM from low-altitude emissions may bias predictions.To address this problem,we describe the modification and validation of an air dispersion model for the simulation of lowaltitude PM dispersion from a typical cotton ginning facility.We found that the regulatory recommended model(AERMOD)overestimated pollutant concentrations by factors of 64.7,6.97 and 7.44 on average for PM 2.5,PM 10,and TSP,respectively.Pollutant concentrations were negatively correlated with height(p<0.05),distance from source(p<0.05)and standard deviation of wind direction(p<0.001),and positively correlated with average wind speed(p<0.001).Based on these results,we developed dispersion correction factors for AERMOD and cross-validated the revised model against independent observations,reducing overestimation factors to 3.75,1.52 and 1.44 for PM 2.5,PM 10 and TSP,respectively.Further reductions in model error may be obtained from use of additional observations and refinement of dispersive correction factors.More generally,the correction permits the validated adjustment and application of pre-existing models for risk assessment and development of remediation techniques.The same approach may also be applied to improve simulations of other air pollutants and environmental conditions of concern.