Dynamic response of mountain tunnel,bridge,and embankment along the Sichuan-Tibet transportation corridor to active fault based on model tests

The Sichuan-Tibet transportation corridor is prone to numerous active faults and frequent strong earthquakes.While extensive studies have individually explored the effect of active faults and strong earthquakes on different engineering structures,their combined effect remains unclear.This research employed multiple physical model tests to investigate the dynamic response of various engineering structures,including tunnels,bridges,and embankments,under the simultaneous influence of cumulative earthquakes and stick-slip misalignment of an active fault.The prototype selected for this study was the Kanding No.2 tunnel,which crosses the Yunongxi fault zone within the Sichuan-Tibet transportation corridor.The results demonstrated that the tunnel,bridge,and embankment exhibited amplification in response to the input seismic wave,with the amplification effect gradually decreasing as the input peak ground acceleration(PGA)increased.The PGAs of different engineering structures were weakened by the fault rupture zone.Nevertheless,the misalignment of the active fault may decrease the overall stiffness of the engineering structure,leading to more severe damage,with a small contribution from seismic vibration.Additionally,the seismic vibration effect might be enlarged with the height of the engineering structure,and the tunnel is supposed to have a smaller PGA and lower dynamic earth pressure compared to bridges and embankments in strong earthquake zones crossing active faults.The findings contribute valuable insights for evaluating the dynamic response of various engineering structures crossing an active fault and provide an experimental reference for secure engineering design in the challenging conditions of the Sichuan-Tibet transportation corridor.

Study on Model Tests and Hydrodynamic Force Models for Free Spanning Submarine Pipelines Subjected to Earthquakes

A test rig is built to model the dynamic response of submarine pipelines with an underwater shaking table in the State Key Laboratory of Coastal and Offshore Engineering, Dalian University of Technology, China. Model tests are carried out to consider the effects of exciting wave directions and types. Based on the experimental results, two hydrodynamic force models derived from Morisen equation and Wake model are presented respectively. By use of hydrodynamic force models suitable for free spanning submarine pipelines under earthquakes, diseretized equations of motion are obtained and finite element models are established to analyze dynamic response of free spanning submarine pipeline subjected to multi-support seismic excitations. The comparison of numerical results with experimental results shows that the improved Morison and Wake hydrodynamic force models could satisfactorily predict dynamic response on the free spanning submarine pipelines subjected to earthquakes.

Model Tests of Pile Defect Detection

The pile, as an important foundation style, is being used in engineering practice. Defects of different types and damages of different degrees easily occur during the process of pile construction. So, dietecting defects of the pile is very important. As so far, there are some difficult problems in pile defect detection. Based on stress wave theory, some of these typical difficult problems were studied through model tests. The analyses of the test results are carried out and some significant results of the low-strain method are obtained, when a pile has a gradually-decreasing crosssection part, the amplitude of the reflective signal originating from the defect is dependent on the decreasing value of the rate of crosssection β. No apparent signal reflected from the necking appeares on the velocity response curve when the value of β is less than about 3. 5 %.

Comparative study of model tests on automatically formed roadway and gob-side entry driving in deep coal mines

Automatically formed roadway(AFR)by roof cutting with bolt grouting(RCBG)is a new deep coal mining technology.By using this technology,the broken roadway roof is strengthened,and roof cutting is applied to cut off stress transfer between the roadway and gob to ensure the collapse of the overlying strata.The roadway is automatically formed owing to the broken expansion characteristics of the collapsed strata and mining pressure.Taking the Suncun Coal Mine as the engineering background,the control effect of this new technology on roadways was studied.To compare the law of stress evolution and the surrounding rock control mechanisms between AFR and traditional gob-side entry driving,a comparative study of geomechanical model tests on the above methods was carried out.The results showed that the new technology of AFR by RCBG effectively reduced the stress concentration of the roadway compared with gob-side entry driving.The side abutment pressure peak of the solid coal side was reduced by 24.3%,which showed an obvious pressure-releasing effect.Moreover,the position of the side abutment pressure peak was far from the solid coal side,making it more beneficial for roadway stability.The deformation of AFR surrounding rock was also smaller than the deformation of the gob-side entry driving by the overload test.The former was more beneficial for roadway stability than the latter under higher stress conditions.Field application tests showed that the new technology can effectively control roadway deformation.Moreover,the technology reduced roadway excavation and avoided resource waste caused by reserved coal pillars.

Wave Motion Compensation Scheme and Its Model Tests for the Salvage of An Ancient Sunken Boat

The application of the vertical hoisting jack and wave motion compensation techniques to the salvage of an ancient sunken boat is introduced. The boat is wooden, loaded with cultural relics. It has been immersed at the bottom of the South China Sea for more than 800 years. In order to protect the structure of the boat and the cultural relics inside to the largest extent, an open caisson is used to hold the sunken beat and the silts around before they are raised from the seabed all together as a whole. In the paper, first, the seakeeping model test of the system of the salvage barge and the open caisson is done to determine some important wave response parameters. And then a further experimental study of the ap- plication of the vertical hoisting jack and wave motion compensation scheme to the salvage of the sunken boat is carried out. In the model tests, the techniques of the integrative mechanic-electronic-hydraulic control, wave motion forecast and wave motion compensation are used to minimize the heave motion of the open caisson. The results of the model tests show that the heave motion of the open caisson can be reduced effectively by the use of the present method.

Model tests on XCC-piled embankment under dynamic train load of high-speed railways

Piled embankments,which offer many advantages,are increasingly popular in construction of high-speed railways in China.Although the performance of piled embankment under static loading is well-known,the behavior under the dynamic train load of a high-speed railway is not yet understood.In light of this,a heavily instrumented piled embankment model was set up,and a model test was carried out,in which a servo-hydraulic actuator outputting M-shaped waves was adopted to simulate the process of a running train.Earth pressure,settlement,strain in the geogrid and pile and excess pore water pressure were measured.The results show that the soil arching height under the dynamic train load of a high-speed railway is shorter than under static loading.The growth trend for accumulated settlement slowed down after long-term vibration although there was still a tendency for it to increase.Accumulated geogrid strain has an increasing tendency after long-term vibration.The closer the embankment edge,the greater the geogrid strain over the subsoil.Strains in the pile were smaller under dynamic train loads,and their distribution was different from that under static loading.At the same elevation,excess pore water pressure under the track slab was greater than that under the embankment shoulder.

Numerical Simulations and Model Tests of the Mooring Characteristic of A Tension Leg Platform Under Random Waves

Analyzing the dynamic response and calculating the tendon tension of the mooring system are necessary for the structural design of a tension leg platform （TLP）. The six-degree-of-freedom dynamic coupling responses and the mooring characteristics of TLP under random waves are studied by using a self-developed program. Results are verified by the 1：40 scaling factor model test conducted in the State Key Laboratory of Ocean Engineering at Shanghai JiaoTong University. The mean, range, and standard deviation of the numerical simulation and model test are compared. The influences of different sea states and wave approach angles on the dynamic response and tendon tension of the mooring system are investigated. The acceleration in the center and corner of the deck is forecasted.

Similarity model tests of movement and deformation of coal-rock mass below stopes

For a study of the movement and deformation of coal-rock mass and low protected seams below a stope,as well as for fracture developments and rules of evolution of permeability,we designed a plane strain model test stand to carry out model tests of similar materials in order to improve the effect of gas drainage from low protected seams and to measure the movement and deformation of coal-rock mass using a method of non-contact close-range photogrammetry.Our results show that 1) using paraffin melting to take the place of coal seam mining can satisfy the mining conditions of a protective seam;2) coal-rock mass under goafs has an upward movement after the protective seam has been mined,causing floor heaving;3) low protected seams become swollen and deformed,providing a good pressure-relief effect and causing the coal-rock mass under both sides of coal pillars to become deformed by compression and 4) the evolution of permeability of low protected seams follows the way of initial values→a slight decrease→a great increase→stability→final decrease.Simultaneously,the coefficient of air permeability increased at a decreasing rate with an increase in interlayer spacing.

Centrifuge model tests on pile-reinforced slopes subjected to drawdown

Piles are generally an effective way to reduce the risk of slope failure.However,previous approaches for slope stability analysis did not consider the effect of the piles coupled with the decrease of the water level(drawdown).In this study,a series of centrifuge model tests was performed to understand the deformation and failure characteristics of slopes reinforced with various pile layouts.In the centrifuge model tests,the pile-reinforced slopes exhibited two typical failure modes under drawdown conditions:across-pile failure and through-pile failure.In the through-pile slope failure,a discontinuous slip surface was observed,implying that the assumption of the slip surface in previous stability analysis methods was unreasonable.The test results showed that drawdown led to instability of the piles in cohesive soil,as the saturated cohesive soil failed to provide sufficient constraint for piles.The slope exhibited progressive failure,from top to bottom,during drawdown.The deformation of the piles was reduced by increasing the embedment depth and row number of piles.In addition,the deformation of soils outside the piles was influenced by the piles and showed a similar distribution shape as the piles,and the similarity degree weakened as the distance from the piles increased.This study also found that the failure mechanism of unreinforced and pile-reinforced slopes induced by drawdown could be described by coupling between the deformation localization and local failure,and it revealed that pile-reinforced slopes could reduce slope deformation localization during drawdown.

Model Tests Research on A Float-Over Barge in Shallow Water Under the Undocking Conditions

In this study,the Jinzhou 9-3 CEPD float-over installation project was investigated.During the undocking condition,the water depth of the motion path of the working barge gradually changed from 10.31 m to 9.41 m.The undocking clearance of the HYSY 228 is smaller than 1 m;therefore,the barge shows highly nonlinear hydrodynamic characteristics,and it is difficult to be accurately simulated by numerical analysis.Thus,it is necessary to obtain the hydrodynamic characteristics and laws of the float-over barge at different water depths by using tank model test,to provide some reference and guidance for float-over operations in shallow water.

Laboratory Model Tests and DEM Simulations of Unloading-Induced Tunnel Failure Mechanism

Tunnel excavation is a complicated loading-unloading-reloading process characterized by decreased radial stresses and increased axial stresses.An approach that considers only loading,is generally used in tunnel model testing.However,this approach is incapable of characterizing the unloading effects induced by excavation on surrounding rocks and hence presents radial and tangential stress paths during the failure process that are different from the actual stress state of tunnels.This paper carried out a comparative analysis using laboratory model testing and particle flow code(PFC2D)-based numerical simulation,and shed light upon the crack propagation process and,microscopic stress and force chain variations during the loading-unloading process.The failure mode observed in the unloading model test is shear failure.The force chains are strongly correlated with the concrete fracture propagation.In addition,the change patterns of the radial and tangential stresses of surrounding rocks in the broken region,as well as the influence of the initial stress on failure loads are revealed.The surrounding soil of tunnel failure evolution as well as extent and shape of the damage zone during the excavation-induced unloading were also studied.

Centrifugal Model Tests on the Settlement of Railway Embankment on Deep,Completely Decomposed Granite Soil

Settlement control of high-speed railways is a key technology in embankment engineering. In order to reveal the engineering characteristics of the deep, completely decomposed granite soil in the Hainan East Ring Railway, four groups of centrifuge model tests were conducted. We studied the settlement properties, under the embankment action, of untreated subsoil, subsoil treated by dynamic compaction, and subsoil reinforced with cement-mixed piles. In particular, we examined the relationship between settlement and time, including the settlement during and after construction. The results show that the Weibull model can describe the relationship between embankment settlement and time well, and that the post-construction settlements of the subsoil meet the requirements of the relevant code. Among the two foundation treatment measures, dynamic compaction is more effective than reinforcement with cement-mixed piles. The tested pressure on the contact surface between embankment and subsoil was obviously different from the commonly used calculated values.

Boundary layer influence on ship model tests in extremely shallow and confined water

Ships sailing in shallow and/or confined water(when calling a harbour or other berthing areas),will experience a different behaviour due to the interaction with vertical and/or horizontal boundaries.Among other hydrodynamic changes induced in confined water,the lateral ship-bank interaction force changes its sign at a critical distance between ship and bank or bottom.However,this distance and its effects on model test results have not been quantified in the past.To investigate the shallow water hydrodynamics coupled with bank effects,systematic model tests were carried out at Flanders Hydraulics Research(FHR)with different ship models.The following parameters were systematically varied:water depth,lateral position,speed,and propeller rate.The change of the ship-bank induced lateral force from an attraction force in medium-deep and shallow water to a repulsion force in extremely shallow water conditions,can be ascribed to the interaction of the boundary layers of the ship model and the environment(tank and installed banks).In this article,a mathematical model is proposed for the critical distance in terms of boundary layer influence thickness.This indicates the range where the model tests are influenced by the horizontal or vertical restrictions combined with the propeller’s dynamic effects.Moreover,the expression has also been extended to describe the relationship between full-scale ship length and water depth with the boundary layer influence thickness.Due to lower Reynolds numbers and relatively thicker boundary layers at model scale,upscaling of the model test results,according to Froude’s law,may provide erroneous results.The influence of the boundary layer initiates at a relatively higher under keel clearance(UKC)for a smaller ship model compared with a larger ship model.Therefore,the boundary layer’s influence with respect to ship model length should be considered during model testing.

Model Tests on the Effect of Dip Angles on Flow Behavior of Liquefied Sand

The flow behavior of liquefied sand is reported using a self-developed testing system that enables the flow processes of liquefied sand to be studied at different slopes of the soil layers.The test device is mainly composed of a vibrating table,a transparent model box and a high-speed video monitoring camera.The tests replicated the horizontal and sloping flows of saturated sand in the model box,which can be tilted to various angles to study the flow characteristics of liquefied sand.The high-speed video monitoring camera captured and recorded the processes within the flowing sand.With increasing downslope,the strain,strain rate,duration time,and sand flow distance increased.The results of our experiment indicate that when selecting sites for engineering structures,the surface downslopes should be taken into account if liquefiable soils are present.Finally,some suggestions regarding site assessment and structural design for sites prone to liquefaction were presented.

Determination of groundwater buoyancy reduction coefficient in clay:Model tests,numerical simulations and machine learning methods

Groundwater plays an essential role in stabilizing underground structures.However,hydrostatic uplift forces from groundwater can create safety hazards.This paper obtained the groundwater buoyancy reduction coefficients of 36 types of clays through model tests and conducted a finite element simulation to obtain the buoyancy reduction coefficients of additional clays with varying soil properties.Machine learning methods,including extreme gradient boosting(XGBoost)and random forest(RF)algorithms,were used to analyze and identify the soil parameters that have a significant impact on the reduction of groundwater buoyancy.It was found that the permeability coefficient and saturation are the primary factors that influence the reduction of groundwater buoyancy.Additionally,the prediction models developed by XGBoost and RF were compared,and their accuracy was evaluated.These research findings can serve as a reference for designing underground structures that can withstand the potential risk of buoyancy in clay.

Explosion resistance performance of reinforced concrete box girder coated with polyurea:Model test and numerical simulation

To study the anti-explosion protection effect of polyurea coating on reinforced concrete box girder,two segmental girder specimens were made at a scale of 1:3,numbered as G(without polyurea coating)and PCG(with polyurea coating).The failure characteristics and dynamic responses of the specimens were compared through conducting explosion tests.The reliability of the numerical simulation using LS-DYNA software was verified by the test results.The effects of different scaled distances,reinforcement ratios,concrete strengths,coating thicknesses and ranges of polyurea were studied.The results show that the polyurea coating can effectively enhance the anti-explosion performance of the girder.The top plate of middle chamber in specimen G forms an elliptical penetrating hole,while that in specimen PCG only shows a very slight local dent.The peak vertical displacement and residual displacement of PCG decrease by 74.8% and 73.7%,respectively,compared with those of specimen G.For the TNT explosion with small equivalent,the polyurea coating has a more significant protective effect on reducing the size of fracture.With the increase of TNT equivalent,the protective effect of polyurea on reducing girder displacement becomes more significant.The optimal reinforcement ratio,concrete strength,thickness and range of polyurea coating were also drawn.

Rainfall-triggered waste dump instability analysis based on surface 3D deformation in physical model test

Landslide is the second largest natural disaster after earthquake. It is of significance to study the evolution laws and failure mechanism of landslides based on its surface 3D deformation information. Based on the rainfall-triggered waste dump instability model test, we studied the failure mechanisms of the waste dump by integrating surface deformation and internal slope stress and proposed novel parameters for identifying landslide stability. We developed a noncontact measurement device, which can obtain millimeter-level 3D deformation data for surface scene in physical model test;Then we developed the similar materials and established a test model for a waste dump. Based on the failure characteristics of slope surface, internal stress of slope body and displacement contours during the whole process, we divided the slope instability process in model test into four stages: rainfall infiltration and surface erosion, shallow sliding, deep sliding, and overall instability. Based on the obtained surface deformation data, we calculated the volume change during slope instability process and compared it with the point displacement on slope surface. The results showed that the volume change can not only reflect the slow-ultra acceleration process of slope failure, but also fully reflect the above four stages and reduce the fluctuations caused by random factors. Finally, this paper proposed two stability identification parameters: the volume change rate above the slip surface and the relative velocity of volume change rate. According to the calculation of these two parameters in model test, they can be used for study the deformation and failure mechanism of slope stability.

Geotechnical centrifuge model tests for explosion cratering and propagation laws of blast wave in sand

This paper presents the explosion cratering effects and their propagation laws of blast waves in dry standard sands using a 450 g-t geotechnical centrifuge apparatus.Ten centrifuge model tests were completed with various ranges of explosive mass,burial depth and centrifuge accelerations.Eleven accelerometers were installed to record the acceleration response in sand.The dimensions of the explosion craters were measured after the tests.The results demonstrated that the relationship between the dimensionless parameters of cratering efficiency and gravity scaled yield is a power regression function.Three specific function equations were obtained.The results are in general agreement with those obtained by other studies.A scaling law based on the combination of the π terms was used to fit the results of the ten model tests with a correlation coefficient of 0.931.The relationship can be conveniently used to predict the cratering effects in sand.The results also showed that the peak acceleration is a power increasing function of the acceleration level.An empirical exponent relation between the proportional peak acceleration and distance is proposed.The propagation velocity of blast waves is found to be ranged between 200 and 714 m/s.

Centrifugal Model Tests on Railway Embankments of Expansive Soils

Based on the centrifugal model tests on railway embankments of expansive soil in Nanning Kunming railway,the author studied several embankments under different physical conditions. The stress and strain states and settlement of the embankments were analyzed, and the obtained results can be used as a reference to field construction.

COUPLING EFFECTS FOR CELL-TRUSS SPAR PLATFORM: COMPARISON OF FREQUENCY-AND TIME-DOMAIN ANALYSES WITH MODEL TESTS

For the floating structures in deepwater, the coupling effects of the mooring lines and risers on the motion responses of the structures become increasingly significant. Viscous damping, inertial mass, current loading and restoring, etc. from these slender structures should be carefully handled to accurately predict the motion responses and line tensions. For the spar platforms, coupling the mooring system and riser with the vessel motion typically results in a reduction in extreme motion responses. This article presents numerical simulations and model tests on a new cell-truss spar platform in the State Key Laboratory of Ocean Engineering in Shanghai Jiaotong University. Results from three calculation methods, including frequency-domain analysis, time-domain semi-coupled and fully-coupled analyses, were compared with the experimental data to find the applicability of different approaches. Proposals for the improvement of numerical calculations and experimental technique were tabled as well.