Effects of the Water-Cement Ratio and the Molding Temperature on the Hydration Heat of Cement

The effects of the water-cement ratio and the molding temperature on the hydration heat of cement were investigated with semi-adiabatic calorimetry.The specimens were prepared with water-cement ratios of 0.31,0.38,and 0.45,and the molding temperature was specified at 10 and 20℃.The experimental results show that,as the water-binder ratio increases,the value of the second temperature peak on the temperature curve of the cement paste decreases,and the age at which the peak appears is delayed.The higher the water-cement ratio,the higher the hydration heat release in the early period of cement hydration,but this trend reverses in the late period.There are intersection points of the total hydration heat curve of the cement pastes under the influence of the water-cement ratio,and this law can be observed at both molding temperatures.With the increase in the molding temperature,the age of the second temperature peak on the temperature curve of the cement paste will advance,but the temperature peak will decrease.The higher the molding temperature,the earlier the acceleration period of the cement hydration began,and the larger the hydration heat of the cement in the early stage,but the smaller the total heat in the late period.A subsection function calculation model of the hydration heat,which was based on the existing models,was proposed in order to predict the heat of the hydration of the concrete.

Dependence of Lower Molding Temperature Limit and Molding Time on Molding Mechanism in Dental Thermoforming

Effectiveness and safety of a sports mouthguard depend on its thickness and material, and the thermoforming process affects these. The purpose of this study was to clarify the effects of differences in molding mechanisms on the lower molding temperature limit and molding time in dental thermoforming. Ethylene vinyl acetate resin mouthguard sheet and two thermoforming machines;vacuum blower molding machine and vacuum ejector/pressure molding machine were used. The molding pressures for suction molding were −0.018 MPa for vacuum blower molding and −0.090 MPa for vacuum ejector molding, and for pressure molding was set to 0.090 MPa or 0.450 MPa. Based on the manufacturer’s standard molding temperature of 95˚C, the molding temperature was lowered in 2.5˚C increments to determine the lower molding temperature limit at which no molding defects occurred. In order to investigate the difference in molding time depending on the molding mechanism, the duration of molding pressure was adjusted in each molding machine, and the molding time required to obtain a sample without molding defects was measured. The molding time of each molding machine were compared using one-way analysis of variance. The lower molding temperature limit was 90.0˚C for the vacuum blower machine, 77.5˚C for the vacuum ejector machine, 77.5˚C for the pressure molding machine at 0.090 MPa, and 67.5˚C for the pressure molding machine at 0.45 MPa. The lower molding temperature limit was higher for lower absolute values of molding pressure. The molding time was shorter for pressure molding than for suction molding. Significant differences were observed between all conditions except between the pressure molding machine at 0.090 MPa and 0.45 MPa (P < 0.01). A comparison of the differences in lower molding temperature limit and molding time due to molding mechanisms in dental thermoforming revealed that the lower molding temperature limit depends on the molding pressure and that the molding time is longer for suction molding than for pressure molding.

Effect of pouring and mold temperatures on hot tearing susceptibility of AZ91D and Mg-3Nd-0.2Zn-Zr Mg alloys

Pouring and mold temperatures are two important parameters during casting magnesium components. The present study examined their influence on hot tearing susceptibility （HTS） of commercial AZ91D and newly developed Mg-3Nd-0.2Zn-Zr （mass fraction, %; NZ30K） magnesium alloys in gravity permanent mold casting condition. The results indicate that mold temperature shows much more significant influence on the HTS of both alloys than pouring temperature whose influence only can be distinguished at low mold temperature （341 K for AZ91D alloy and 423 K for NZ30K alloy）. Hot tearing susceptibility prediction model concerning feeding parameters, grain size and solidification range, is more suitable to estimate the HTS of different magnesium alloys than the model only concerning feeding parameters. In order to achieve better hot tearing resistance, the ranges of pouring and mold temperatures are suggested to be 961-991 K and≥641 K for AZ91D alloy, 1003-1033 K and≥623 K for NZ30K alloy, respectively.

Improvement of the CFRP Mechanical Properties Using Taguchi Method to Optimize the Formation Conditions

Carbon fiber composites have high strength, high stiffness and light weight characteristics to apply to many fields, such as leisure, energy and transportation industries. The CFRP （carbon fiber reinforced polymers/plastics） composites made of carbon fibers as reinforcement and epoxy resins as matrix were prepared by drum winding process. Various parameters such as molding temperature, molding pressure and pressing time were selected as the pre-pregs were laminated to be the CFRP. The effects of fabricating parameters which affected the mechanical properties of CFRPs were analyzed by Taguchi method in this study. The results showed that molding temperature was the main factor to influence the mechanical properties of composites.

Effect of Molding Material Temperature on Workpiece in FDM

Fused deposition molding is an advanced kind of rapid prototyping technology. On the accuracy of the forming process, the research on the temperature of the molding material is based on the analysis of the forming parameters. The influence of the tenlperature of the molding material on the specimen is reasonably described by the actual forming part and the finite element analysis model. The experimental results show that the temperatur（ of the molding material is less affected by the temperature of the molding material in a certain range. This will lay the theoretical foundation for the formation of the molding technology in the future

Hierarchical Crystalline Structures Induced by Temperature Profile in HDPE Bars during Melt Penetration Process

The hierarchical crystalline morphologies and orientation structures across the thickness direction in high-density polyethylene （HDPE） molded bars were investigated via a novel melt-penetrating processing method named multi-melt multi-injection molding （M3IM）. The samples with various mold temperatures （20, 40 and 60 ℃） were prepared, and the effects of the external temperature profile on the evolution of crystalline microstructures were studied. With scanning electron microscopy （SEM）, the transition of crystalline morphology from ring-banded structure to oriented lamellae was observed with decreasing mold temperature, and the oriented lamellae were formed at the sub-skin layer of the samples at the lowest mold temperature, which was further testified by differential scanning calorimetry （DSC）. With the decline of mold temperature, the degree of orientation, obtained from two-dimensional small angle X-ray scattering （2D-SAXS）, was increased and long periods rose a little. Thus, decreasing mold temperature was beneficial to the formation of orientation structures because the relaxation of chains was weakened.