Dynamic simulation analysis of molten salt reactor-coupled air-steam combined cycle power generation system

A nonlinear dynamic simulation model based on coordinated control of speed and flow rate for the molten salt reactor and combined cycle systems is proposed here to ensure the coordination and stability between the molten salt reactor and power system.This model considers the impact of thermal properties of fluid variation on accuracy and has been validated with Simulink.This study reveals the capability of the control system to compensate for anomalous situations and maintain shaft stability in the event of perturbations occurring in high-temperature molten salt tank outlet parameters.Meanwhile,the control system’s impact on the system’s dynamic characteristics under molten salt disturbance is also analyzed.The results reveal that after the disturbance occurs,the controlled system benefits from the action of the control,and the overshoot and disturbance amplitude are positively correlated,while the system power and frequency eventually return to the initial values.This simulation model provides a basis for utilizing molten salt reactors for power generation and maintaining grid stability.

Preliminary safety analysis for heavy water-moderated molten salt reactor

The heavy water-moderated molten salt reactor(HWMSR)is a newly proposed reactor concept,in which heavy water is adopted as the moderator and molten salt dissolved with fissile and fertile elements is used as the fuel.Issues arising from graphite in traditional molten salt reactors,including the positive temperature coefficient and management of highly radio-active spent graphite waste,can be addressed using the HWMSR.Until now,research on the HWMSR has been centered on the core design and nuclear fuel cycle to explore the viability of the HWMSR and its advantages in fuel utilization.However,the core safety of the HWMSR has not been extensively studied.Therefore,we evaluate typical accidents in a small modular HWMSR,including fuel salt inlet temperature overcooling and overheating accidents,fuel salt inlet flow rate decrease,heavy water inlet temperature overcooling accidents,and heavy water inlet mass flow rate decrease accidents,based on a neutronics and thermal-hydraulics coupled code.The results demonstrated that the core maintained safety during the investigated accidents.

Preliminary analysis of fuel cycle performance for a small modular heavy water-moderated thorium molten salt reactor

Heavy water-moderated molten salt reactors(HWMSRs)are novel molten salt reactors that adopt heavy water rather than graphite as the moderator while employing liquid fuel.Owing to the high moderating ratio of the heavy water moderator and the utilization of liquid fuel,HWMSRs can achieve a high neutron economy.In this study,a large-scale small modular HWMSR with a thermal power of 500 MWth was proposed and studied.The criticality of the core was evaluated using an in-house critical search calculation code(CSCC),which was developed based on Standardized Computer Analyses for Licensing Evaluation,version 6.1.The preliminary fuel cycle performances(initial conversion ratio(CR),initialfissile fuel loading mass,and temperature coefficient)were investigated by varying the lattice pitch(P)and the molten salt volume fraction(VF).The results demonstrate that the temperature coefficient can be negative over the range of investigated Ps and VFs for both 233U-Th and LEU-Th fuels.A core with a P of 20 cm and a VF of 20%is recommended for 233U-Th and LEU-Th fuels to achieve a high performance of initial CR and fuel loading.Regarding TRU-Th fuel,a core with a smaller P(~5 cm)and larger VF(~24%)is recommended to obtain a negative temperature coefficient.

Synchrotron radiation-based materials characterization techniques shed light on molten salt reactor alloys

From a safety point of view, it is important to study the damages and reliability of molten salt reactor structural alloy materials, which are subjected to extreme environments due to neutron irradiation, molten salt corrosion, fission product attacks, thermal stress, and even combinations of these. In the past few years, synchrotron radiation-based materials characterization techniques have proven to be effective in revealing the microstructural evolution and failure mechanisms of the alloys under surrogating operation conditions. Here, we review the recent progress in the investigations of molten salt corrosion,tellurium(Te) corrosion, and alloy design. The valence states and distribution of chromium(Cr) atoms, and the diffusion and local atomic structure of Te atoms near the surface of corroded alloys have been investigated using synchrotron radiation techniques, which considerably deepen the understandings on the molten salt and Te corrosion behaviors. Furthermore, the structure and size distribution of the second phases in the alloys have been obtained, which are helpful for the future development of new alloy materials.

Radiation dose distribution of liquid fueled thorium molten salt reactor

A liquid fueled thorium molten salt reactor(TMSR-LF),one of the Generation IV reactors,was designed by the Shanghai Institute of Applied Physics,Chinese Academy of Sciences.This study uses the‘rt code to calculate the neutron and gamma dose rate distributions around the reactor.Multiple types of tallies and variance reduction techniques were employed to reduce calculation time and obtain convergent calculation results.Based on the calculation and analysis results,the TMSR-LF1 radiation shield with a 60-cm serpentine concrete layer and a 120-cm ordinary concrete layer is able to meet radiation requirements.The gamma dose rate outside the reactor biological shield was 16.1 mSv h-1;this is higher than the neutron dose rate of 3.71×10^(–2)mSv h^(-1).The maximum thermal neutron flux density outside the reactor biological shield was 1.899103 cm^(-2)s^(-1),which was below the 19105 cm^(-2)s^(-1)limit.

Study on dynamic characteristics of fission products in 2 MW molten salt reactor

In this study,a numerical flow model of the fission products(FPs)in the primary loop system of a molten salt reactor(MSR)was established and solved using Mathematica 7.0.The simulation results were compared with those of the ORIGEN-S program in the static burnup mode,and the deviation was found to be less than 10%,which indicates that the results are in good agreement.Furthermore,the FPs distribution in the primary loop system under normal operating conditions of the 2 MW MSR was quantitatively analyzed.In addition,the distribution phenomenon of the FPs under different flow rate conditions was studied.At the end of life,the FPs activity in the core region(including active region,and upper and lower plenum regions)accounted for 77.3%,and that in the hot leg #1,main pump,hot leg #2,heat exchanger,and cold leg region accounted for 1.2%,16.15%,0.99%,2.5%,and 1.9%,respectively,of the total FPs in the primary loop under normal operating conditions.The proportion of FPs in the core decreased with the increase in flow rate in the range of 2.24-22,400 cm^3 s^-1.The established analytical method and conclusions of this study can provide an important basis for radiation safety design of the primary loop,radioactive source management design,thermal-hydraulic safety analysis,and radiochemical analysis of FPs of 2 MW MSRs.

Numerical and experimental investigation of a new conceptual fluoride salt freeze valve for thorium-based molten salt reactor

To improve the reliability and reduce energy consumption,a conceptual design of a freeze valve is proposed for the thorium-based molten salt reactor(TMSR)concept.Fins were utilized in this new design to enhance heat transfer and realize passive shut-off function,which could not be realized by the previous design.An experimental apparatus using the fluoride salt FLiNaK was constructed to conduct a series of preliminary solidification and melting experiments.In addition,the enthalpy-porosity method of ANSYS■Fluent solver was applied to simulate the solidification process of the salt at a specified operating temperature.Temperature distributions of the fluoride salt,solidification/melting time,and frozen plug effect were analyzed under natural convection heat transfer in an open space.The calculated salt temperatures exhibited good agreement with the experimental values.The results indicated that the range of effective operating temperature is 530-600℃ for the finned freeze valve.In this study,the ideal set operating temperature of the finned freeze valve was chosen as 560℃ to achieve competent performance.Moreover,560℃ is additionally the highest set operating temperature for maintaining excellent cooling performance and sustaining deep-frozen condition of the salt plug.At this set operating temperature,the simulation data indicated that the molten salt in the flat part of the finned freeze valve will completely solidify at 10.5 min.The percentage of solid salt in the flat and lower transitional parts of the valve reaches 29.60% in 30.0 min.Furthermore,the surface temperature of the proposed freeze valve is 11.10% lower compared with that of the TMSR freeze valve at a cooling gas supply of 173 m^3/h.Therefore,the new freeze valve was proven to be capable of reducing the energy consumption and realizing the passive shut-off function.

Flow field effect of delayed neutron precursors in liquid-fueled molten salt reactors

In molten salt reactors(MSRs),the liquid fuel salt circulates through the primary loop and a part of the delayed neutron precursors(DNPs)decays outside the reactor core.To model and analyze the flow field effect of DNPs in channel-type liquid-fueled MSRs,a three-dimensional space-time dynamics code,named ThorCORE3D,that couples neutronics,core thermalhydraulics,and a molten salt loop system was developed and validated with the Molten Salt Reactor Experiment(MSRE)benchmarks.The effects of external loop recirculation time,fuel flow rate,and core flow field distribution on the delayed neutron fraction loss of MSRE at steadystate were modeled and simulated using the ThorCORE3D code.Then,the flow field effect of the DNPs on the system responses of the MSRE in the reactivity insertion transient under different initial conditions was analyzed systematically for the channel-type liquid-fueled MSRs.The results indicate that the flow field condition has a significant effect on the steady-state delayed neutron fractions and will further affect the transient power and temperature responses of the reactor system.The analysis results for the effect of the DNP flow field can provide important references for the design optimization and safety analysis of liquid-fueled MSRs.

Study on the production characteristics of(131)^I and(90)^Sr isotopes in a molten salt reactor

The production of radionuclides(90)^Sr and(131)^I in molten salt reactors is an attractive option to address the global shortage of radionuclides.This study evaluated the production characteristics of(90)^Sr and(131)^I in a modular molten salt reactor,such as equilibrium time,yield,and cooling time of isotopic impurities.The fuel burn-up of a small modular molten salt reactor was analyzed by the Triton module of the scale program,and the variation in the fission yields of the two nuclides and their precursors with burn-up time.The yield of(131)^I and~(131)Te has been increasing during the lifetime.131 I has an equilibrium time of about 40 days,a saturation activity of about 40,300 TBq,and while~(131)Te takes 250 min to reach equilibrium,the equilibrium activity was about 38,000 TBq.The yields of90 Sr and~(90)Kr decreased gradually,the equilibrium time of90 Kr was short,and(90)^Sr could not reach equilibrium.Based on the experimental data of molten salt reactor experiment,the amount of nuclide migration to the tail gas and the corresponding cooling time of the isotope impurities under different extraction methods were estimated.Using the HF-H_2 bubbling method,3.49×10^(5)TBq of(131)^I can be extracted from molten salt every year,and after13 days of cooling,the impurity content meets the medical requirements.Using the electric field method,1296 TBq of(131)^I can be extracted from the off-gas system(its cooling time is 11 days)and 109 TBq of(90)^Sr.The yields per unit power for(131)^I and(90)^Sr is approximately 1350 TBq/MW and 530 TBq/MW,respectively,which shows that molten salt reactors have a high economic value.

Transmutation of 129I in a single-fluid double-zone thorium molten salt reactor

Herein, we assess the129I transmutation capability of a 2250-MWt single-fluid double-zone thorium molten salt reactor(SD-TMSR) by considering two methods. One is realized by loading an appropriate amount of129I before the startup of the reactor, and the amount of129I during operation is kept constant by online feeding129I.The other adopts only an initial loading of129I before startup, and no other129I is fed online during operation.The investigation first focuses on the effect of the loading of I on the Th-233U isobreeding performance. The results indicate that a233U isobreeding mode can be achieved for both scenarios for a 60-year operation when the initial molar proportion of LiI is maintained within 0.40% and 0.87%, respectively. Then, the transmutation performances for the two scenarios are compared by changing the amount of injected iodine into the core. It is found that the scenario that adopts an initial loading of129I shows a slightly better transmutation performance in comparison with the scenario that adopts online feeding of129I when the net233U productions for the two scenarios are kept equal. The initial loading of129I scenario with LiI = 0.87% molar proportion is recommended for129I transmutation in the SD-TMSR,and can transmute 1.88 t of129I in the233U isobreeding mode over 60 years.

Burnup optimization of once-through molten salt reactors using enriched uranium and thorium

The advantages of once-through molten salt reactors include readily available fuel,low nuclear proliferation risk,and low technical difficulty.It is potentially the most easily commercialized fuel cycle mode for molten salt reactors.However,there are some problems in the parameter selection of once-through molten salt reactors,and the relevant burnup optimization work requires further analysis.This study examined once-through graphitemoderated molten salt reactor using enriched uranium and thorium.The fuel volume fraction(VF),initial heavy nuclei concentration(HN_(0)),feeding uranium enrichment(E_(FU)),volume of the reactor core,and fuel type were changed to obtain the optimal conditions for burnup.We found an optimal region for VF and HN_(0) in each scheme,and the location and size of the optimal region changed with the degree of E_(FU),core volume,and fuel type.The recommended core schemes provide a reference for the core design of a once-through molten salt reactor.

Use of Thorium in the Generation IV Molten Salt Reactors and Perspectives for Brazil

Interest in thorium stems mainly from the fact that it is expected to have a substantial increase in uranium prices. So, advanced fuel cycles which increase the reserves of nuclear materials are interesting, particularly, the use of thorium is to produce the fissile isotope ^233U. Thorium is three to five times more abundant than uranium in the earth＇s crust. Additionally, thoria produces less radiotoxicity than the UO2, because it produces fewer amounts of actinides. ThO2 has higher corrosion resistance, besides being chemically stable, and the burning of Pu in a reactor based in thorium also decreases the inventories of Pu from the current fuel cycles. There are some ongoing projects in the world, taking into consideration the proposed goals for Generation IV reactors, namely： sustainability, economics, safety and reliability, proliferation resistance and physical protection. Some developments on the use of thorium in reactors are underway, with the support of the IAEA （International Atomic Energy Agency） and some govern like molten salt reactor. In this paper, we discuss the future importance of thorium, particularly for Brazil, which has large mineral reserves of this strategic element, the characteristics of the molten salt reactor and the experience of the IPEN （Instituto de Pesquisas Energ6ticas e Nucleares） in the purification of thorium compounds.

Characterization of molten 2LiF–BeF_2 salt impregnated into graphite matrix of fuel elements for thorium molten salt reactor

The impregnation behavior of molten 2LiF–BeF_2(FLiBe) salt into a graphite matrix of fuel elements for a solid fuel thorium molten salt reactor(TMSR-SF) at pressures varying from 0.4 to 1.0 MPa was studied by mercury intrusion, molten salt impregnation, X-ray diffraction, and scanning electron microscopy techniques.It was found that the entrance pore diameter of the graphite matrix is less than 1.0 μm and the contact angle is about 135°. The threshold impregnation pressure was found to be around 0.6 MPa experimentally, consistent with the predicted value of 0.57 MPa by the Washburn equation. With the increase of pressure from 0.6 to 1.0 MPa, the average weight gain of the matrix increased from 3.05 to 10.48%,corresponding to an impregnation volume increase from 2.74 to 9.40%. The diffraction patterns of FLiBe are found in matrices with high impregnation pressures(0.8 MPa and1.0 MPa). The FLiBe with sizes varying from tens of nanometers to a micrometer mainly occupies the open pores in the graphite matrix. The graphite matrix could inhibit the impregnation of the molten salt in the TMSR-SF with a maximum operation pressure of less than 0.5 MPa.

Application of Monte Carlo method to calculate the effective delayed neutron fraction in molten salt reactor

Delayed neutron loss is an important parameter in the safety analysis of molten salt reactors. In this study,to obtain the effective delayed neutron fraction under flow condition, a delayed neutron precursor transport was implemented in the Monte Carlo code MCNP. The moltensalt reactor experiment(MSRE) model was used to analyze the reliability of this method. The obtained flow losses of reactivity for 235 U and 233 U fuels in the MSRE are223 pcm and 100.8 pcm, respectively, which are in good agreement with the experimental values(212 pcm and100.5 pcm, respectively). Then, six groups of effective delayed neutron fractions in a small molten salt reactor were calculated under different mass flow rates. The flow loss of reactivity at full power operation is approximately105.6 pcm, which is significantly lower than that of the MSRE due to the longer residence time inside the active core. The sensitivity of the reactivity loss to other factors,such as the residence time inside or outside the core and flow distribution, was evaluated as well. As a conclusion,the sensitivity of the reactivity loss to the residence time inside the core is greater than to other parameters.

Transition toward thorium fuel cycle in a molten salt reactor by using plutonium

The molten salt reactor(MSR), as one of the Generation Ⅳ advanced nuclear systems, has attracted a worldwide interest due to its excellent performances in safety, economics, sustainability, and proliferation resistance. The aim of this work is to provide and evaluate possible solutions to fissile 233 U production and further the fuel transition to thorium fuel cycle in a thermal MSR by using plutonium partitioned from light water reactors spent fuel. By using an in-house developed tool, a breeding and burning(B&B) scenario is first introduced and analyzed from the aspects of the evolution of main nuclides, net 233 U production, spectrum shift, and temperature feedback coefficient. It can be concluded that such a Th/Pu to Th/^(233)U transition can be accomplished by employing a relatively fast fuel reprocessing with a cycle time less than 60 days. At the equilibrium state, the reactor can achieve a conversion ratio of about 0.996 for the 60-day reprocessing period(RP) case and about 1.047 for the 10-day RP case.The results also show that it is difficult to accomplish such a fuel transition with limited reprocessing(RP is 180 days),and the reactor operates as a converter and burns the plutonium with the help of thorium. Meanwhile, a prebreeding and burning(PB&B) scenario is also analyzed briefly with respect to the net 233 U production and evolution of main nuclides. One can find that it is more efficient to produce 233 U under this scenario, resulting in a double time varying from about 1.96 years for the 10-day RP case to about 6.15 years for the 180-day RP case.

Development of a MCNP5 and ORIGEN2 based burnup code for molten salt reactor

The Molten Salt Reactor(MSR) is one of the six advanced reactor nuclear energy systems for further research and development selected by Generation IV International Forum(GIF),which is distinguished by its core in which the fuel is dissolved in molten fluoride salt.Because fuel flow in the primary loop,the depletion of MSR is different from that of solid-fuel reactors.In this paper,an MCNP5 and ORIGEN2 Coupled Burnup(MOCBurn) code for MSR is developed under the MATLAB platform.Some new methods and novel arrangements are used to make it suitable for fuel flow in the MSR.To consider the fuel convection and diffusion in the primary loop of MSR,fuel mixing calculation is carried out after each burnup time step.Modeling function for geometry with repeat structures is implicated for reactor analysis with complex structures.Calculation for a high-burnup reactor pin cell benchmark is performed using the MOCBurn code.Results of depletion study show that the MOCBurn code is suitable for the traditional solid-fuel reactors.A preliminary study of the fuel mixture effect in MSR is also carried out.

Steady thermal hydraulic analysis for a molten salt reactor

The Molten Salt Reactor (MSR) can meet the demand of transmutation and breeding. In this study, theoretical calculation of steady thermal hydraulic characteristics of a graphite-moderated channel type MSR is conducted. The DRAGON code is adopted to calculate the axial and radial power factor firstly. The flow and heat transfer model in the fuel salt and graphite are developed on basis of the fundamental mass, momentum and energy equations. The results show the detailed flow distribution in the core, and the temperature profiles of the fuel salt, inner and outer wall in the nine typical elements along the axial flow direction are also obtained.

Properties of phosphate glass waste forms containing fluorides from a molten salt reactor

Radioactive fluoride wastes are generated during the operation of molten salt reactors(MSRs) and reprocessing of their spent fuel.Immobilization of these wastes in borosilicate glass is not feasible because of the very low solubility of fluorides in this host.Alternative candidates are thus an active topic of research including phosphatebased glasses,crystalline ceramics,and hybrid glass-ceramic systems.In this study,mixed fluorides were employed as simulated MSRs waste and incorporated into sodium aluminophosphate glass to obtain phosphate-based waste form.These waste forms were characterized by X-ray diffraction,Raman spectroscopy,and scanning electron microscopy.Leaching tests were performed in deionized water using the product consistency test A method.This study demonstrates that up to 20 mol%of simulated radioactive waste can be introduced into the NaA1 P glass matrix,and the chemical durability is much better than that of borosilicate.The addition of Fe_2O_3 in the NaAlP glass matrix results in increases of the chemical durability at the expense of fluoride loading(to 6.4 mol%).Phosphate glass vitrification of radioactive waste containing fluorides is a potential method to treat and dispose of MSR wastes.

Effects of fuel salt composition on fuel salt temperature coefficient(FSTC)for an under-moderated molten salt reactor(MSR)

With respect to a liquid-fueled molten salt reactor(MSR),the temperature coefficient of reactivity mainly includes the moderator temperature coefficient(MTC)and the fuel salt temperature coefficient(FSTC).The FSTC is typically divided into the Doppler coefficient and the density coefficient.In order to compensate for the potentially positive MTC,the FSTC should be sufficiently negative,and this is mostly optimized in terms of the geometry aspect in pioneering studies.However,the properties of fuel salt also directly influence the FSTC.Thus,the effects of different fuel salt compositions including the^(235)U enrichment,heavy metal proportion in salt phase(HM proportion),and the^7Li enrichment on FSTC are investigated from the viewpoint of the essential six-factor formula.The analysis is based on an undermoderated MSR.With respect to the Doppler coefficient,the temperature coefficient of the fast fission factors(a_T(ξ))is positive and those of the resonance escape probability(a_T(p)),thermal reproduction factor(a_T(g)),thermal utilization factor(a_T(f)),and total non-leakage probability(a_T(λ))are negative.With respect to the density coefficient,a_T(p)and a_T(g)are positive,while the others are negative.The results indicate that the effects of the^(235)U enrichment and HM on FSTC are mainly reflected in a_T(e)and a_T(p),which are the dominant factors when the neutron spectrum is relatively hard.Furthermore,the^7Li enrichment influences FSTC by a_T(f)and a_T(λ),which are the key factors in a relative soft spectrum.In order to obtain a more negative FSTC for an under-moderated MSR,the possible positive density coefficient,especially its a_T(p),should be suppressed.Thus,a lower^(235)U enrichment(albeit higher than a certain value,5 wt%in this article)along with a lower HM proportion and/or a higher^7Li enrichment are recommended.The analyses provide an approach to achieve a more suitable fuel salt composition with a sufficiently negative FSTC.

Research on the effect of the heavy nuclei amount on the temperature reactivity coefficient in a small modular molten salt reactor

Small modular thorium-based graphite-moderated molten salt reactors (smTMSRs), which combine the advantages of small modular reactors and molten salt reactors, are regarded as a wise development path to speed deployment time. In a smTMSR, low enriched uranium and thorium fuels are used in once-through mode, which makes a marked difference in their neutronic properties compared with the case when a conventional molten salt breeder reactor is used. This study investigated the temperature reactivity coefficient (TRC) in a smTMSR, which is mainly affected by the molten salt volume fraction (VF) and the heavy nuclei concentration in the fuel salt (HN). The fourfactor formula method and the reaction rate method were used to indicate the reasons for the TRC change, including the fuel density effect, the fuel Doppler effect, and the graphite thermal scattering effect. The results indicate that only the fuel density has a positive effect on the TRC in the undermoderated region. Thermal scattering from both salt and graphite has a significant negative influence on the TRC in the overmoderated region. The maximal effective multiplication factor, which shows the highest fuel utilization, is located at 10% VF and 12 mol% HN and is still located in the negative TRC region. In addition, on increasing the heavy nuclei amount from 2 mol% HN to 12 mol% HN (VF = 10%), the total TRC undergoes an obvious change from - 11 to - 3 pcm/K, which implies that the change in the HN caused by the fuel feed online should be small to avoid potential trouble in the reactivity control scheme.