Electromagnetic Design of a Switched Reluctance Motor With Segmental Rotors and Full-pitch Windings

整距绕组分块转子开关磁阻电机具有高速运行时低风（油）阻和低铁心损耗等优点，特别适合用于航天航空驱动系统。根据整距绕组分块转子开关磁阻电机的基本工作原理，结合输出功率与平均转矩的关系，将绕组电流等效为方波，推导出了整距绕组分块转子开关磁阻电机的主体尺寸计算公式；基于电机定转子未对齐位置和对齐位置的电磁特性，以及整距绕组分块转子开关磁阻电机的电磁特点，确定了定、转子极弧系数选取的规则；同时分析了绕组匝数等主要尺寸的选取的规则；最后，基于上述方法优化设计了一台实验样机，并通过有限元仿真及实验验证了整距绕组分块转子开关磁阻电机的电磁设计方法的正确性。

Initial Rotor Position Detection of 12/10 Flux-switching Permanent Magnet Motors

电机转子初始位置检测的精度直接决定其启动运行时的性能。针对12/10极永磁磁通切换型电机,在验证其凸极性的基础上,采用注入脉振高频信号实现转子初始位置估计。通过对传统高频脉振正弦电压信号注入的分析,研究了基于高频方波或三角波的注入方法,再利用电流差值调制或直接信号调制方法得到位置误差信号,同时根据磁路的饱和效应,通过对d轴电流过零点时间差值的累加,实现了磁极方向辨识。分析了位置误差信号的系数与初始位置检测收敛性的关系。通过实验验证了所提方法的正确性和可行性。

Broken Rotor Bar Fault Diagnosis of Induction Motors Using a Hybrid Bare-bones Particle Swarm Optimization Algorithm

在传统定子电流频谱分析中,感应电机转子断条故障特征经常被基波分量淹没而无法准确检测。针对该问题,提出一种基于混合骨干微粒群优化算法的转子断条故障诊断新方法。该方法首先根据电流信号与单位余弦基函数的内积最大准则,利用混合骨干微粒群算法强大的全局搜索能力,准确估计出基波波形参数;然后利用波形参数构造出基波表达式,并将其从原电流信号中剔除,达到突出故障特征的目的。针对微粒群算法在进化后期收敛缓慢的缺点,通过K–均值聚类方式,引入单纯形法对其进行改进,使整个算法的广度探索与深度开发能力得到了有效均衡。最后,对模拟数据和实测信号进行实验,结果验证了所提方法的有效性和优越性。

Rotor Strength Analysis of High-speed Permanent Magnet Synchronous Motors

为了对转子进行有效的冷却，在满足电机电磁性能的前提下，可通过减小保护套的厚度来尽可能增大定转子之间的气隙，因而必须对保护套和永磁体进行强度校核。将转子受力状况简化为平面应变问题，在此基础上推导出了两层过盈配合、三层过盈配合转子的应力场、应变场、位移场的解析公式，并利用有限元方法验证了解析公式的正确性。归纳了高速情况下热套式永磁转子强度设计准则，为转子的优化设计提供了理论依据。以一台额定转速120kr／min、10kW的高速永磁同步电机为例，给出了两种常用过盈配合高速电机转子的强度设计方法。

Temperature Field Analysis of Mine Flameproof Outer Rotor Permanent Magnet Synchronous Motor with Different Cooling Schemes

Aiming at the problem of temperature rise of mine flameproof outer rotor permanent magnet synchronous motor,based on the fluid structure coupling method,the temperature distribution of motor under three cooling schemes of air cooling and water cooling are calculated respectively.For the structure I air cooling system,the influence of different number of heat sink on the maximum temperature rise and pressure drop of fluid channel is analyzed,and the parameters of heat sink are optimized.For the structure II air cooling system,the influence of setting fillet at the turn back of the fluid channel on the head loss in the fluid domain of the motor is analyzed,and the influence of different fillet radius on the head loss and the maximum temperature rise in the fluid domain is obtained.For the structure II water cooling system,the influence of different water flow speed on the maximum temperature rise of the motor is analyzed,and the influence of different assembly clearance of modular stator teeth and yoke on the maximum temperature rise of the motor is analyzed.The cooling effect and temperature rise distribution characteristics of the three cooling schemes are compared and analyzed.Finally,a water-cooled prototype is manufactured,and the temperature rise experiment is carried out,and the influence of the thermal deformation of fluid channel,stator yoke and stator teeth on the maximum temperature of the motor is analyzed.The results show that the calculated temperature field after considering the thermal deformation is closer to the experimental value,which verifies the accuracy of the calculation results,It also provides a reference for the selection and design of the cooling structure of the same type of PMSM electric roller.

Broken Rotor Bar Fault Detection of Induction Motors Using a Joint Algorithm of Trust Region and Modified Bare-bones Particle Swarm Optimization

A precise detection of the fault feature parameter of motor current is a new research hotspot in the broken rotor bar(BRB) fault diagnosis of induction motors. Discrete Fourier transform(DFT) is the most popular technique in this field, owing to low computation and easy realization. However, its accuracy is often limited by the data window length, spectral leakage, fence e ect, etc. Therefore, a new detection method based on a global optimization algorithm is proposed. First, a BRB fault current model and a residual error function are designed to transform the fault parameter detection problem into a nonlinear least-square problem. Because this optimization problem has a great number of local optima and needs to be resolved rapidly and accurately, a joint algorithm(called TR-MBPSO) based on a modified bare-bones particle swarm optimization(BPSO) and trust region(TR) is subsequently proposed. In the TR-MBPSO, a reinitialization strategy of inactive particle is introduced to the BPSO to enhance the swarm diversity and global search ability. Meanwhile, the TR is combined with the modified BPSO to improve convergence speed and accuracy. It also includes a global convergence analysis, whose result proves that the TR-MBPSO can converge to the global optimum with the probability of 1. Both simulations and experiments are conducted, and the results indicate that the proposed detection method not only has high accuracy of parameter estimation with short-time data window, e.g., the magnitude and frequency precision of the fault-related components reaches 10^(-4), but also overcomes the impacts of spectral leakage and non-integer-period sampling. The proposed research provides a new BRB detection method, which has enough precision to extract the parameters of the fault feature components.

Effects of Transverse Temperature Gradient on the Rotor Velocity in an Ultrasonic Motor

As a result of the nonlinear effect, acoustic streaming has been widely used for increasing the transport coefficient or driving a rotor, for example, in resonant cavities and non-contact ultrasonic motors. It has been demonstrated by experiments that a temperature gradient transverse to the wave propagating direction can significantly increase the velocity of the streaming flows in resonant cavities. To check whether the transverse temperature gradient can also increase the working velocity of acoustic streaming-driven motors, we investigate this issue by numerically solving the hydrodynamic equations. It is found that the velocity of the rotor only weakly depends on the transverse temperature gradient, e.g., even with a temperature difference of 40℃ between the rotor and the stator, the velocity increases only -8.8%.

Rotor Design and Finite Element Analysis of Traveling Wave Rotaty Ultrasonic Motor

The dynamic transfer mechanism of the traveling wave rotary ultrasonic motor rotor-stator’ s contact surface is studied in the paper and the key parts stator and cone flexible rotor of ultrasonic motor are designed.The three-dimensional contact model and finite element model considering the radial sliding between the rotor and the stator are established. The relation between the stator surface particle that amplitude frequency characteristics,resonance speed,radial displacement of ultrasonic motor and the tooth height are analyzed. Mass point radial relative displacement of contact surface between the cone flexible rotor,flexible rotor and the stator are contrasted. The cone flexible rotor is better placed on the surface of the stator tooth through its elastic deformation is interpreted. The cone flexible rotor reduces the radial slip between the stator and the output efficiency of ultrasonic motor is improved. The displacement trajectory of the stator surface is synthesized in a row wave cycle. The method of the stator mass point elliptical motion drives the rotor rotation is verified.

Online Detection of Broken Rotor Bar Fault in Induction Motors by Combining Estimation of Signal Parameters via Min-norm Algorithm and Least Square Method

Current research in broken rotor bar （BRB） fault detection in induction motors is primarily focused on a high-frequency resolution analysis of the stator current. Compared with a discrete Fourier transformation, the parametric spectrum estimation technique has a higher frequency accuracy and resolution. However, the existing detection methods based on parametric spectrum estima- tion cannot realize online detection, owing to the large computational cost. To improve the efficiency of BRB fault detection, a new detection method based on the min-norm algorithm and least square estimation is proposed in this paper. First, the stator current is filtered using a band-pass filter and divided into short overlapped data windows. The min-norm algorithm is then applied to determine the fre- quencies of the fundamental and fault characteristic com- ponents with each overlapped data window. Next, based on the frequency values obtained, a model of the fault current signal is constructed. Subsequently, a linear least squares problem solved through singular value decomposition is designed to estimate the amplitudes and phases of the related components. Finally, the proposed method is applied to a simulated current and an actual motor, the results of which indicate that, not only parametric spectrum estimation technique.

Study on Rotor IGBT Chopper Control for Induction Motor Drive

Rotor chopper control is a simple and effective drive method for induction motor. This paper presents a novel IGBT chopper topology,which can both adjust rotor resistance and protect IGBT efficiently. Investigation on the quasi transient state of the rotor rectifying circuit is made, and a nonlinear mapping between the equivalent resistance and the duty cycle is deduced. Furthermore, the method for determining the magnitude of the external resistor is introduced.

供电电压闪变对异步电动机转子故障在线检测的影响及应对

供电电压闪变可能对异步电动机转子故障在线检测产生不利影响,导致基于定子电流信号分析(motor current signature analysis,MCSA)的转子故障在线检测方法失效。通过理论分析,揭示供电电压闪变恶化转子故障在线检测性能的机制。提出免于供电电压闪变影响的异步电动机转子故障在线检测方法,首先,根据转子故障主特征频率分量预判转子健康或故障;继而,根据转子故障独有的辅助特征频率分量进一步确认转子健康或故障。仿真与实验结果证明了该方法的有效性。

一种自适应扩展卡尔曼滤波的永磁同步电机无位置传感器矢量控制

在粗差干扰或噪声统计偏差情况下,扩展卡尔曼滤波(EKF)对永磁同步电机(PMSM)的速度和转子位置估计存在精度下降问题,为此提出一种基于新息序列的自适应扩展卡尔曼滤波算法(AEKF)。首先,将粗差干扰加入系统观测方程中,分析粗差干扰对系统观测精度的影响。其次,为增强算法的抗扰性能,在新息协方差计算中设置加权系数,通过调整临近时刻的新息协方差阵权重,计算出新息协方差值,并更新到卡尔曼增益的计算。最后,建立AEKF数学模型,并对比粗差干扰与噪声统计出现偏差情况下,AEKF与EKF两种策略的观测性能。仿真和实验结果表明,在粗差干扰或噪声统计信息出现偏差情况下,AEKF算法对永磁同步电机转速的观测具备更强的鲁棒性及更高的预测精度。

螺杆机用并轴双转子永磁电机齿槽力矩机理分析与抑制

针对并轴双转子永磁电机过大的齿槽力矩以及转矩脉动大等电磁问题,采用传统单个槽齿槽转矩理论以及双转子电机边端力矩波动理论进行分析,计算了并轴双转子电机齿槽力矩的特殊组成成分以及其各部分转矩的谐波阶次。分析改变磁极偏心距和转子斜极对电机齿槽力矩和转矩特性的影响。采用响应面法构建电机的多目标优化模型,通过改变永磁体偏心距和斜极块数来约束电机的优化变量,并采取约束关系以及优化目标求解出最优转子结构参数。构建有限元模型,验证齿槽力矩理论的正确性。对比采用最优转子结构参数下电机的电磁性能与优化前电机的电磁性能,优化后电机的齿槽力矩、转矩脉动等电磁性能进一步提升,验证了采用磁极偏心和转子斜极复合结构的有效性。

宽转子无轴承开关磁阻电机的计及磁饱和径向力模型

针对无轴承开关磁阻电机现有的基于无磁饱和假设的数学模型只适用于未磁饱和工况的缺点,为宽转子单绕组无轴承开关磁阻电机建立了一种可以计及磁饱和影响的全周期径向力数学模型。首先依据该电机的磁场有限元分析结果,基于麦克斯韦应力法求出了径向力关于气隙磁密的表达式;然后对铁心材料的非线性磁化特性进行拟合,再根据该电机的等效磁路计算了计及磁饱和影响的气隙磁密;之后建立了该电机的径向力模型,并在对比分析了边缘气隙磁密和主气隙磁密对径向力的影响后,对所建径向力模型进行简化,以减小计算量和复杂度。最后利用三维有限元分析进行验证,结果表明所建径向力模型对该电机未磁饱和、部分磁饱和以及完全磁饱和工况均适用。计及磁饱和的全周期径向力模型的建立,可以为电机运行特性分析、本体优化设计以及控制策略研究提供更准确的理论参考。

1.1 MW高速内置式永磁同步电机新型转子拓扑设计与强度优化

大功率高速永磁电机中通常采用绑扎碳纤维护套的方式来降低转子应力,然而护套厚度过大会导致等效气隙增加,电机性能随之降低。针对这一问题,设计了一种具有新型转子拓扑结构的1.1 MW、18 000 r/min的内置式高速永磁同步电机。该结构采用永磁体分段设计,并增设加强筋,分担转子隔磁桥处的应力,使护套厚度得到有效降低。同时,将转子外部隔磁桥处替换为非导磁填充块,阻断漏磁路径,提升永磁体利用率。最后,有限元分析结果表明,相较于初始模型,新型结构电机在等效气隙增大1.5 mm的情况下,输出转矩达到600.44 N·m,增加了16.86 N·m,并且新型转子铁心最大应力降低了496.82 MPa,转子结构的机械强度得到显著提高,可为大功率高速永磁电机转子拓扑设计提供参考。

宽转子极无轴承开关磁阻电机径向力模型全周期拓展

针对单绕组宽转子极无轴承开关磁阻电机在定转子极非完全交叠区间的径向悬浮力模型空白、已有定转子极完全交叠区间径向悬浮力模型推导过程复杂且计算量大的不足,首先通过磁场有限元分析,分别确定了该电机在定转子非完全交叠区间和完全交叠区间的电磁场几何分布,计算了气隙磁密,再根据麦克斯韦应力法分别推导了这2个区间的径向力表达式,从而建立该电机在一个完整周期范围内的径向力数学模型,并通过与三维有限元计算结果的对比验证该模型的准确性。相比于利用等效磁路图推导径向力模型而言,该建模过程更简便,计算量也更小。全周期径向力模型的建立,不仅能为电机本体和控制器设计提供理论参考,还有助于提高该电机控制策略设计的灵活性,也可以提高与传统单绕组无轴承电机控制器的通用性。

混合转子永磁电机双风道冷却系统设计

混合转子永磁电机具有高功率密度的优势,但也导致电机散热空间和散热能力不足等问题。为此,根据其特有的转子结构提出一种双风道冷却系统,并采用计算流体力学(Computational fluid dynamics,CFD)的方法对电机温度场进行验证。首先,根据电机损耗和尺寸设计一个适合双风道的轴流风扇。其次,对不同进、出风口的结构参数进行仿真,对比和分析仿真结果,选出冷却性能较好的参数组合。最后对单风道和该参数组合下的双风道进行数值模拟,仿真结果表明,使用双风道冷却结构后电机散热能力显著提升。

双并列转子永磁直驱电机转子不平衡力分析与优化

双并列转子永磁直驱电机受轴间距限制,设计时会切掉部分定子铁心和绕组,造成转子电磁力不平衡。为最大限度地抑制转子所受的不平衡电磁力,该文从双并列转子结构出发,分析了电机绕组电感参数不对称的原因,提出通过合理设计线圈跨距和分布平衡三相电感。在此基础上,构建转子所受总电磁力的数学模型,理论分析各个分力的来源及影响因素,研究各个分力对转子所受总电磁力的影响,提出了优化占空角、优化耦合间距、采用定子端部不对称结构、采用转子偏心结构和切除部分单元电机五种优化方法,实现对转子所受电磁力的优化,探讨了不同方法的优化效果,以及其对转矩脉动的影响,总结了不同优化方法的优缺点。

基于动态磁网络法大型感应电机阻抗参数及起动特性计算

为提高大型感应电机动态阻抗参数及起动特性计算的准确性及计算效率,构建了考虑电机转子转速变化引起气隙磁导变化的非线性动态磁网络模型。以一台6.5 MW大型感应电机为例,分析起动电流变化对电机内各处饱和程度的影响机理,在此基础上,根据磁力线路径及电机内饱和程度确定动态磁网络模型中的非线性磁导的计算方法。将动态磁网络模型与转子趋肤效应模型相结合,提出计及漏磁并考虑转子转速变化及饱和偏移现象的电机动态阻抗参数的计算方法。推导并建立基于转子多回路法的大型感应电机的动态数学模型,根据电机瞬态过程中的电磁耦合关系,确定动态数学模型与磁网络模型的动态耦合求解方法,提出大型电机瞬态过程中考虑电流、转速、饱和及趋肤程度变化的动态阻抗参数及起动特性的计算方法。通过与有限元计算结果及实验结果对比,验证了所提出计算方法的正确性。