Wearing a mouthguard reduces the risk of sports-related injuries, but a more comfortable design is required in order to increase the wearing rate. The aim of this study was to investigate a thermoforming method that d...Wearing a mouthguard reduces the risk of sports-related injuries, but a more comfortable design is required in order to increase the wearing rate. The aim of this study was to investigate a thermoforming method that decreases palatal thickness while maintaining labial and buccal thickness. Mouthguards were fabricated from an ethylene-vinyl acetate sheet (thickness: 4.0 mm) by using a vacuum forming machine. Four working models were prepared: 1) the anterior height was 25-mm and the posterior height was 20-mm (model A), 2) model A with the palate trimmed (model B), 3) heights 5 mm greater than model A (model C), and 4) model C with the palate trimmed (model D). The two forming conditions were as follows: 1) The sheet was formed when it sagged 15 mm below the level of the sheet frame at the top of the post under ordinary use (control);2) The sheet frame at the top of the post was lowered and the sheet covered the model when it sagged by 15 mm. The rear side of the model was pushed to move the model forward 20 mm, and then the sheet was formed (MP). Differences in mouthguard thickness due to forming conditions and model forms were analyzed by two-way analysis of variance and Bonferroni’s multiple comparison tests. Difference in forming conditions was similar for all model forms;for the MP, the thickness of the incisal edge, labial surface, cusp and buccal surface were greater, and the palatal surface was thinner than the control. On the labial and buccal surface, the thickness difference due to the model form was observed only for the MP, and models A and B were thicker than models C and D. The palatal thickness tended to be thin in the models with the trimmed palate. This study suggested that the labial and buccal thickness of the mouthguard can be maintained, and the palatal thickness can be decreased by using the model with the palate trimmed with the forming method in which the model position is moved forward immediately before the vacuum formation.展开更多
文摘Wearing a mouthguard reduces the risk of sports-related injuries, but a more comfortable design is required in order to increase the wearing rate. The aim of this study was to investigate a thermoforming method that decreases palatal thickness while maintaining labial and buccal thickness. Mouthguards were fabricated from an ethylene-vinyl acetate sheet (thickness: 4.0 mm) by using a vacuum forming machine. Four working models were prepared: 1) the anterior height was 25-mm and the posterior height was 20-mm (model A), 2) model A with the palate trimmed (model B), 3) heights 5 mm greater than model A (model C), and 4) model C with the palate trimmed (model D). The two forming conditions were as follows: 1) The sheet was formed when it sagged 15 mm below the level of the sheet frame at the top of the post under ordinary use (control);2) The sheet frame at the top of the post was lowered and the sheet covered the model when it sagged by 15 mm. The rear side of the model was pushed to move the model forward 20 mm, and then the sheet was formed (MP). Differences in mouthguard thickness due to forming conditions and model forms were analyzed by two-way analysis of variance and Bonferroni’s multiple comparison tests. Difference in forming conditions was similar for all model forms;for the MP, the thickness of the incisal edge, labial surface, cusp and buccal surface were greater, and the palatal surface was thinner than the control. On the labial and buccal surface, the thickness difference due to the model form was observed only for the MP, and models A and B were thicker than models C and D. The palatal thickness tended to be thin in the models with the trimmed palate. This study suggested that the labial and buccal thickness of the mouthguard can be maintained, and the palatal thickness can be decreased by using the model with the palate trimmed with the forming method in which the model position is moved forward immediately before the vacuum formation.
