Co-pyrolysis of Sewage Sludge with Distillation Residue: Kinetics Analysis via Iso-conversional Methods

This study explored the synergistic interaction of sewage sludge(SS)and distillation residue(DR)during co-pyrolysis for the optimized treatment of sewage sludge in cement kiln systems,utilizing thermogravimetric analysis(TGA)and thermogravimetric analysis with mass spectrometry(TGA-MS).The results reveal the coexisting synergistic and antagonistic effects in the co-pyrolysis of SS/DR.The synergistic effect arises from hydrogen free radicals in SS and catalytic components in ash fractions,while the antagonistic effect is mainly due to the melting of DR on the surface of SS particles during pyrolysis and the reaction of SS ash with alkali metals to form inert substances.SS/DR co-pyrolysis reduces the yielding of coke and gas while increasing tar production.This study will promote the reduction,recycling,and harmless treatment of hazardous solid waste.

A method for establishing a bearing residual life prediction model for process enhancement equipment based on rotor imbalance response analysis

A rotating packed bed is a typical chemical process enhancement equipment that can strengthen micromixing and mass transfer.During the operation of the rotating packed bed,the nonreactants and products irregularly adhere to the wire mesh packing in the rotor,thus resulting in an imbalance in the vibration of the rotor,which may cause serious damage to the bearing and material leakage.This study proposes a model prediction for estimating the bearing residual life of a rotating packed bed based on rotor imbalance response analysis.This method is used to determine the influence of the mass on the imbalance in the vibration of the rotor on bearing damage.The major influence on rotor vibration was found to be exerted by the imbalanced mass and its distribution radius,as revealed by the results of orthogonal experiments.Through implementing finite element analysis,the imbalance response curve for the rotating packed bed rotor was obtained,and a correlation among rotor imbalance mass,distribution radius of imbalance mass,and bearing residue life was established via data fitting.The predicted value of the bearing life can be used as the reference basis for an early safety warning of a rotating packed bed to effectively avoid accidents.

Residue analysis and dissipation of monosulfuron in soil and wheat

HPLC-UV residue analytical method for monosulfuron [N-[( 4' -methyl) pyrimidin- 2' -yl]-2-nitrophenylsulfonyl urea] in soil and wheat was developed. Monosulfuron residues were recovered by solvent extraction, followed by liquid-liquid partition, and C 18 cartrige clean-up. Excellent method recoveries ranging from 95%—104% for both fortified soil and wheat grain were obtained with coefficients of variation 1.5%—11.8%. The minimum detectable quantities in soil and wheat were both 4 ng, the limit of detection was 0.02 mg/kg. When monosulfuron was applied according to double dosage of maximum recommended use direction(120 g ai/hm 2 of 10% monosulfuron wettable powder sprayed for once during development of wheat) in field studies conducted in Shandong Province and near Beijing, monosulfuron residues was not detected in soil and wheat samples collected 75 d after application. Laboratory soil degradation studies showed that monosulfuron degraded faster in acidic soil and strong alkaline soil than in neutral or weak alkaline soil. Half lives in Jiangxi soil, Shijiazhuang soil, Jiangsu soil and Heilongjiang soil were 41, 48, 87 and 84 d respectively. Monosulfuron residues dissipated rapidly in Shandong and Beijing field test sites with half-lives of less than 14 d.

Residue analysis and dissipation of a new fungicide 2-allylphenol in tomato

The method of residue analysis of a new synthesized fungicide 2-allylphenol was studied by simulating the active compound structure in Gingko tree(Gingko biloba L.) and its dissipation rate and terminal residue levels in tomato under field condition. Residues of 2-allylphenol were extracted from tomato matrix with acetone, purified by liquid-liquid extraction and Florisil cartrieges, and then determined by HPLC with UV-detector. The minimum detectable amount of 2-allylphenol was 3×10 -9 g, the minimum detectable concentration of 2-allylphenol in the samples of tomato were 0.01 mg/kg. The ranges of average recoveries and coefficient variation of the method were 87.7%—90.2% and 1.25%—2.06%, respectively. The dissipation rate and terminal residue levels in tomato were determined with the method described above. The results showed that the half-life of 2-allylphenol in tomato was 6.37 d, and 2-allylphenol declined with 82.6% of the initial deposit remaining in tomato at harvest. The terminal residue levels in tomato were 0.15 mg/kg and 0.20 mg/kg following the recommended doses and time intervals.

Residue Analysis of 55% MCPA·ametryn·diuron WP

The digestion regularity of MCPA, ametryn and dim＇on which were the active ingredients of 55% MCPA · ametryn · diuron WP in sugarcane leaves and soil of sugarcane plantation collected from Changsha of Hunan Province and Haikou of Hainan Province in 2009 and 2010were studied in the paper, and the results showed that these three agents had rapid digestion. The final residue test showed that beth MCPA and ametryn had not been detected in the study; the average resi- dues of diuron in the soil collected from Hunan Province in 2009 and 2010 were 0.018 and 0.015 mg/kg, respectively which were slightly larger than the critical value of 0. 013mg,/kg; diuron had no been detected in other treatments.

Method for Analysis of Ethephon Residue in Walnuts

[Objectives] This study was conducted to establish an analytical method for the determination of ethephon residue in walnuts by UPLC-MS/MS. [Methods] This study was conducted to establish an analytical method for the determination of ethephon residue in walnuts by UPLC-MS/MS. [Results] The limit of quantification was 0.1 mg/kg and the recoveries were 94%-105% with the relative standard deviations of 0.82%-2.64% at the spiked levels of 0.1-5.0 mg/kg. [Conclusions] The accuracy and sensitivity of the method meet the requirements of pesticide residue analysis, and the experimental method is simple to operate.

Residual curvature migration velocity analysis for angle domain common imaging gathers

Pre-stack depth migration velocity analysis is one of the keys to influencing the imaging quality of pre-stack migration.In this paper we cover a residual curvature velocity analysis method on angle-domain common image gathers（ADCIGs） which can depict the relationship between incident angle and migration depth at imaging points and update the migration velocity.Differing from offset-domain common image gathers（ODCIGs）,ADCIGs are not disturbed by the multi-path problem which contributes to imaging artifacts,thus influencing the velocity analysis.On the basis of horizontal layers,we derive the residual depth equation and also propose a velocity analysis workflow for velocity scanning.The tests to synthetic and field data prove the velocity analysis methods adopted in this paper are robust and valid.

3-D FINITE ELEMENT ANALYSIS OF THE EFFECT OF WELDING RESIDUAL STRESS ON HYDROGEN DIFFUSION IN HYDROGEN CONTAINED ENVIRONMENT

The hydrogen distribution of 16MnR steel weldment in hydrogen contained environment was calculated using the finite element method （ FEM）. The effect of welding residual stress on hydrogen diffusion has been discussed using a 3-D sequential coupling finite element analysis procedure complied by Abaqus code. The hydrogen diffusion coefficient in weld metal, the heat affected zone （HAZ）, and the base metal of the 16MnR steel weldment were measured using the electrochemical permeation technique. The hydrogen diffusion without the effect of stress was also calculated and compared. Owing to the existence of welding residual stress, the hydrogen concentration was obviously increased and the hydrogen wouM diffuse and accumulate in the higher stress region.

Identifying the best common factor model via exploratory eactor analysis

Currently,there is no solid criterion for judging the quality of the estimators in factor analysis.This paper presents a new evaluation method for exploratory factor analysis that pinpoints an appropriate number of factors along with the best method for factor extraction.The proposed technique consists of two steps:testing the normality of the residuals from the fitted model via the Shapiro-Wilk test and using an empirical quantified index to judge the quality of the factor model.Examples are presented to demonstrate how the method is implemented and to verify its effectiveness.

Analysis model for damage of reinforced bars in RC beams under contact explosion

The load-bearing capacity of reinforced concrete(RC) beams primarily relies on internal reinforced bars.However, limited research has been conducted on the dynamic response of these bars. To address this gap, this study has established an analytical model using dimensional analysis for calculating the deformation of reinforced bars within RC beams subjected to contact explosion. Comparison with experimental data reveals that the model has a relative error of 5.22%, effectively reflecting the deformation of reinforced bars. Additionally, based on this model, the study found that while concrete does influence the deformation of reinforced bars, this influence can be disregarded in comparison to the material properties of the bars themselves. The findings of this study have implications for calculating the residual load-bearing capacity of damaged RC beams, evaluating the extent of damage to RC beams after blast loading, and providing guidance for the blast-resistant design of RC structures.

Testing heteroscedasticity in nonparametric regression models based on residual analysis

The importance of detecting heteroscedasticity in regression analysis is widely recognized because efficient inference for the regression function requires that heteroscedasticity should be taken into account. In this paper, a simple test for heteroscedasticity is proposed in nonparametric regression based on residual analysis. Furthermore, some simulations with a comparison with Dette and Munk＇s method are conducted to evaluate the performance of the proposed test. The results demonstrate that the method in this paper performs quite satisfactorily and is much more powerful than Dette and Munk＇s method in some cases.

Numerical and Dimensional Analysis for Prediction of Line Heating Residual Deformations

Line heating process is a very complex phenomenon as a variety of factors affects the amount of residual deformations. Numerical thermal and mechanical analysis of line heating for prediction of residual deformation is time consuming. In the present work dimensional analysis has been presented to obtain a new relationship between input parameters and resulting residual deformations during line heating process. The temperature distribution and residual deformations for 6 mm, 8 mm, 10 mm and 12 mm thick steel plates were numerically estimated and compared with experimental and published results. Extensive data generated through a validated FE model were used to find co-relationship between the input parameters and the resulting residual deformation by multiple regression analysis. The results obtained from the deformation equations developed in this work compared well with those of the FE analysis with a drop in the computation time in the order of 100 (computational time required for FE analysis is around 7 200 second to 9 000 seconds and where the time required for getting the residual deformation by developed equations is only 60 to 90 seconds).

Equivalence of Ratio and Residual Approaches in the Homotopy Analysis Method and Some Applications in Nonlinear Science and Engineering

A ratio approach based on the simple ratio test associated with the terms of homotopy series was proposed by the author in the previous publications.It was shown in the latter through various comparative physical models that the ratio approach of identifying the range of the convergence control parameter and also an optimal value for it in the homotopy analysis method is a promising alternative to the classically used h-level curves or to the minimizing the residual(squared)error.A mathematical analysis is targeted here to prove the equivalence of both the ratio approach and the traditional residual approach,especially regarding the root-finding problems via the homotopy analysis method.Examples are provided to further justify this.Moreover,it is conjectured that every nonlinear differential equation can be considered as a root-finding problem by plugging a parameter in it from a physical viewpoint.Two examples from the boundary and initial and value problems are provided to verify this assertion.Hence,besides the advantages as deciphered in the previous publications,the feasibility of the ratio approach over the traditional residual approach is made clearer in this paper.

Pore pressure fluctuations of overlying aquifer during residual coal mining and water-soil stress coupling analysis

Three test models and a simulation model were constructed based on the prevailing conditions of the Taiping coalmine in order to analyze pore pressure fluctuations of an overlying aquifer during residual coal mining. As well, the relation between pore pressure and soil stress was evaluated. The model tests show the vibrations of pore pressure and soil stress as a result of mining activities. The simulation model tells of the response characteristics of pore pressure after mining and its distribution in the sand aquifer. The comparative analysis reveals that pore pressure and soil stress vibration are activated by unexpected events occurring in mines, such as collapsing roofs. An increased pore pressure zone always lies above the wall in front or behind the working face of a mine. Both pore pressure and vertical stress result in increasing and decreasing processes during movements of the working face of a mine. The vibration of pore pressure always precedes soil stress in the same area and ends with a sharp decline. Changes in pore pressure of sand aquifer are limited to the area of stress changes. Obvious changes are largely located in a very small frame over the mining face.

Numerical Analysis of Thermal Distortion and Residual Stresses in H13 Steel Due to Vacuum Gas Quenching

Heat treated steel components often suffer distortion and residual stress effects when cooled to room temperature. A numerical analysis of a vacuum gas quenched die block made of H 13 was carried out utilising a nonlinear thermoelastic-plastic stress model together with the fluid flow and thermal profiles within the furnace. Simulation procedures for stress behaviour of the die were developed for both direct quench and marquench processes. Results of the initial thermal analysis indicated that the temperature difference between the surface and core of the die during direct quenching (gas pressure is 4 bar) was larger than that due to marquenching ( gas pressure is 4 bar at the beginning and 2 bar near isothermal hold). Simulation of the cooling rates at the surface and core of the die during marquenching correlated well with the experimental data. Further stress simulation indicated that the final thermal distortion and residual stresses in the die after direct quenching were larger than those due to marquenching. The findings of the numerical analysis suggested that marquenching is recommended for this die because it could reduce the temperature difference in the die and thus result in less thermal distortion and residual stresses.

Finite Element Analysis and Experiment Research on Surface Residual Stress of Ceramics Grinding

The theoretical model of residual stress of ceramics grinding has been established applying thermal elastoplastic mechanics theory. While grinding at the course of grinding wheel moved along workpiece surface the distributing regulation of residual stress can be simplified into thermal elastioplastic mechanical issue, under the action of the both moving centralized force and heat source. Calculating and evaluating of surface residual stress using current procedure of finite element analysis which has been reformed is successful. Comparing with X-ray diffraction experiment method, satisfactory precision has been acquired. The results of experiment show the changing regularity of residual stresses after grinding Al 2O 3 using diamond wheel, on condition that alter grinding parameters. The values of residual compress stress are taken place changing at key certain critical point on their figure as follow: When grinding depth a p is lower than 50 μm, the residual compress stresses are increased with grinding depth increasing, on the contrary as a p>50 μm. At V w<8 m/min, the residual compress stresses increased rapidly with feed speed of workpiece increasing, on the contrary at V w>8 m/min.When V s<25 m/s the residual stress increased with wheel speed increasing and keep stable in value at V s>25 m/s.According to grinding mechanism the cause of residual stress transform has been explained.

Finite element analysis of the angular distortion and residual stress in underwater wet welding

In underwater environment, the shape, voltage, and energy density of the welding arc vary because of the high pressure and there are notable changes in workpiece cooling conditions due to the strong cooling effect of water. As a result, there are clear differences between the residual stress and thermal distortion in underwater wet welding and those in conventional welding （in air）. Considering these process features, a thermo-mechanical finite element model of underwater wet bead-on-plate welding was established. The influences of the water compressing action to the arc and the enhanced heat losses caused by the surrounding water on the residual stress and the angular distortion of the workpiece were analyzed. Results show that the angular distortion gets smaller in deeper water, and that the longitudinal residual stress gets smaller as water flows faster.

Finite element analysis on temperature field and residual stress of welding assembly for I-beam and end-plate

Based on full scale model of 1-beam and end-plate welding assembly with medium plate, welding temperature field and residual stress were simulated, infrared thermometers were employed to measure the real-time temperature Jbr verification purposes. Results show that the measured thermal cycle curves match well with the simulation result. Simulation results of welding residual stress indicate that the values of longitudinal and transverse stress on the upper surface of the plate are higher than the normal stress; higher tensile stresses exist at the end of the web weld toes and in the central area of the flange weld toes. The dangerous zones are located at the central areas of weld toes of the flange welds and near weld toes of the web welds.

Residual Analysis for Auto-Correlated Econometric Model

The aim of this article is to provide residual analysis for a time series data of Gross Domestic Product (GDP) of the Sudan. An econometric time series model with macroeconomic variables is conducted to examine the goodness of fit using residual. Many statistical tests are used in time series models in order to make it a stationary series. After applying these tests, the time series became stationary and integrated;thus, Box-Jenkins procedure is used for the determination of ARIMA, AR (0,1,0) in this study. This identified technique is useful for analyzing this study.

Analysis on Content and Distribution of Residual Film in Fields of Different Crops

Before spring ploughing in 2019,the representative fields of the 8^(th) Division were selected,and residual film at different depths of soil in three areas of the 8^(th) Division was collected. Through the analysis on the weight and amount of residual film at different depths of soil,it was found that the average content of residual film in the 8^(th) Division was 104 kg/hm^2. From high to low,the content sequence of residual film in the three areas was Anjihai area,Mosuowan area and Xiayedi area. The average amount of residual film collected from the cotton field in the three areas was greater than that from the corn field. In the three areas,the content of residual film in the cotton field at the depth of 0-10 and 11-30 cm was higher than that in the corn field,while the content of residual film at the depth of 31-50 cm in the corn field was higher than that in the cotton field.