Mechanical Characterization of Rubber Latex-Based Carpets (Hevea bresiliensis): Influence of Rubber Latex Content and Fiber Fabrics (Cotton and Mosquito Nets) on Wear Resistance of Rubber Latex-Based Carpets

This work focuses on the development of carpets from sand, fabrics of cotton fiber and mosquito nets and rubber latex. Following a study on the choice of the best formulations, the quantity of rubber latex used for shaping varies between 14% and 18% (latex/sand + latex ratio) for the carpet with the fabric of mosquito nets and between 16% and 18% for the one made with the fabric of cotton fiber. Thus, with a mixture of sand, fiber fabrics (cotton and mosquito nets) and rubber latex, carpets were developed. In addition, the wear test carried out on these samples indicates that it is possible to produce carpets with the new material made of rubber sand and latex: SABLATEX At room temperature. Following the characterization test, it resorts to only 16% latex with cotton fiber fabric, allowing to have carpets with good mechanical characteristics.

Rational Design of Layered SnS2 on Ultralight Graphene Fiber Fabrics as Binder-Free Anodes for Enhanced Practical Capacity of Sodium-Ion Batteries

Generally,the practical capacity of an electrode should include the weight of non-active components such as current collector,polymer binder,and conductive additives,which were as high as 70 wt%in current reported works,seriously limiting the practical capacity.This work pioneered the usage of ultralight reduced graphene fiber(rGF)fabrics as conductive scaffolds,aiming to reduce the weight of nonactive components and enhance the practical capacity.Ultrathin SnS2 nanosheets/rGF hybrids were prepared and used as binder-free electrodes of sodium-ion batteries(SIBs).The interfused graphene fibers endow the electrode a porous,continuous,and conductive network.The in situ phase transformation from SnO2 to SnS2 could preserve the strong interfacial interactions between SnS2 and graphene.Benefitting from these,the designed binder-free electrode delivers a high specific capacity of 500 mAh g?1 after 500 cycles at a current rate of 0.5 A g?1 with almost 100%Coulombic efficiency.Furthermore,the weight percentage of SnS2 in the whole electrode could reach up to 67.2 wt%,much higher than that of common electrode configurations using Cu foil,Al foil,or carbon cloth,significantly highlighting the ultralight characters and advantages of the rGF fabrics for using as binder-free electrodes of SIBs.

Femtosecond laser fabrication of nanograting-based distributed fiber sensors for extreme environmental applications

The femtosecond laser has emerged as a powerful tool for micro-and nanoscale device fabrication. Through nonlinear ionization processes, nanometer-sized material modifications can be inscribed in transparent materials for device fabrication. This paper describes femtosecond precision inscription of nanograting in silica fiber cores to form both distributed and point fiber sensors for sensing applications in extreme environmental conditions. Through the use of scanning electron microscope imaging and laser processing optimization,high-temperature stable, Type II femtosecond laser modifications were continuously inscribed,point by point, with only an insertion loss at 1 d B m~(-1) or 0.001 d B per point sensor device.High-temperature performance of fiber sensors was tested at 1000℃, which showed a temperature fluctuation of ±5.5℃ over 5 days. The low laser-induced insertion loss in optical fibers enabled the fabrication of a 1.4 m, radiation-resilient distributed fiber sensor. The in-pile testing of the distributed fiber sensor further showed that fiber sensors can execute stable and distributed temperature measurements in extreme radiation environments. Overall, this paper demonstrates that femtosecond-laser-fabricated fiber sensors are suitable measurement devices for applications in extreme environments.

Fabrication of Tm-Doped Fibers for High Power and 121W Output All-Fiber Tm-Doped Fiber Laser

We fabricate the Tm-doped double cladding silica fiber by using the vapor-solution hybrid-doping method, then build up an all-fiber Tin-doped fiber laser which can provide the output power of up to 121 W, corresponding to a slope efficiency of 51% and an optical-optical efficiency of 48%. By using the domestic Tin-doped fiber, it is the first time a hundred-watt level output at 1915nm has been achieved, to the best of our knowledge. The thermal effect of Tm-doped fiber laser is also analyzed.

Effect of Twisted Fiber on Flexural Property and Microstructure of Woven Fabric Reinforced Composite

Two kinds of 2.5D deep straight-joint structure ultra-high molecular weight polyethylene（UHMWPE）（twisted and original） fibers woven fabric reinforced epoxy resin composites were prepared by the hand lay-up method. Subsequently, the flexural property, microstructures, and failure mechanisms of the composites were also investigated. The average flexural strength of 2.5D deep bend-joint structure twisted fiber and original fiber woven fabric composites were 176.66 MPa and 204.45 MPa, respectively. The results of the characteristics indicated that the twist was the main factor which affected the flexural performance. Flexural property vitally relied on the strength of the fiber itself. Twist decreased the strength of the yarns, which meant that when the mechanical property of woven fabric reinforced composites was improved, the yarns must be kept straight in the woven fabric. The study are extremely valuable to guide the improvement of the mechanical property of the woven fabric reinforced composites.

Fabrication and formation mechanism of NbC_x-C three-dimensional netted fibers

Micrometer NbC_x-C three-dimensional netted fibers were synthesized by thecarbothermal method under 0.1 MPa of N_2 ambient atmosphere at a relatively low temperature. Rawmaterials were commercial powders of Nb_2O_5 (99.95 percent), reactive carbon (99.99 percent), NaCl(99.95 percent) and sucrose (99.94 percent). The relationship of the fabrication processing with thecomposition, crystal structure and morphology of fibers was investigated. The formation mechanismwas also proposed and discussed.

INVESTIGATIONS ON NANOMETER-SIZED ULTRAMICRO-ELECTRODES(Ⅱ)—FABRICATION, CHARACTERIZATION OF CARBON FIBER CYLINDER ULTRAMICROELECTRODES

Described here are the fabrication and characterization of carbon fiber cylinder ultramicroelectrodes with cylinder length of less than 100 am, total tip diameter of several hundreds nanometers. The electrodes have been fabricated by direct etching of carbon fiber using an ion beam thinner. Optical microscopy, scanning electron microscopy (SEM), cyclic voltammetry have been employed to characterize those electrodes. The experimental results obtained indicate the electrodes can be used for in vivo detection of neurotransmitters such as dopamine, 5—hydroxytryptamine in a single cell.

ADSORPTION CAPACITY OF ACTIVATED CARBON FIBER FABRIC IN CYANIDE LEACHING LIQUOR OF GOLD ORES

Adsorption capacity of ACFF in cyanide leaching liquor of gold ores was studied with cyanide leaching liquor of gold ores, containing various kinds of ions. The adsorbed leaching liquor was analyzed by atomic emission spectroscopy and colorimetric method. The contents of various kinds of ions in ACFF were determined with X-ray photoctron spectroscopy. ACFF not only adsorbed gold but also adsorbed arsenic, nickel, zinc, calcium, sulphur, bismuth, copper, iron, silver and cyanide anion. Atomic percentage of C and those of O, N, Zn, Fe increase and decrease respectively with the increase of the layer depth, while those of Ca, Au, Ag keep constant.

Directly electrospinning submillimeter continuous fibers on tubes to fabricate H2S detectors with fast and high response

The fast and high response detection of neurotoxic H_(2)S is of great importance for the environment.In this paper,directly electrospinning technology on the ceramic tube is developed to improve the response of H_(2)S detector based on superlong SnO_(2)fibers.The submillimeter continuous fibers are deposited directly on ceramic tubes by in-situ electrospinning method and can keep morphology of fibers during calcination.By employing this technology,CuO-doped SnO_(2)fiber H_(2)S detectors are fabricated,and 10%atom CuO-doped SnO_(2)H_(2)S detector shows the highest response of 40 toward 1 ppm H_(2)S at 150℃while the response is only 3.6 for the H_(2)S detector prepared in traditional route.In addition,the in-situ electrospinning H_(2)S detectors show faster response and recovery compared to the H_(2)S detectors fabricated by the conventional way.The high and fast response of H_(2)S detectors based on in-situ electrospinning can be ascribed to the continuous fiber structure and CuO modification.The present in-situ electrospinning technology may provide a new strategy for the development of other gasdetectors and bio-detectors with fast and high response.

Design and Fabrication of Two Kinds of Photonic Crystal Fibers

As a new type optical fiber,because of its particular optical properties,photonic crystal fibers(PCFs) have attracted the academic and industrial field widespread attention.So,the researches about PCFs have made great progress in recent decade.In this paper,two kinds of PCFs constructions are numerically investigated and its leakage-loss properties are simulated.Based on the results of calculations,both the two types of PCFs are fabricated using glass capillary tube stacking.And the process of fiber drawing is described in this paper.

Mass-producible low-cost flexible electronic fabrics for azo dye wastewater treatment by electrocoagulation

Electrocoagulation is progressively becoming an ecologically friendly water treatment method owing to its lack of secondary pollution,high active ingredient concentration,high treatment effectiveness,simple equipment,and simplicity of automated control implementation.Herein,electrocoagulation is offered as a method for treating wastewater containing azo dyes using a revolutionary flexible electronic fabric that can be mass-producible at a reasonable price.A computer-controlled machine embroiders 316L stainless steel fiber(316L SSF)onto an insulating fabric to manufacture a flexible electronic device of cathode and anode with a monopolar arrangement on the fabric surface.Using methyl orange(MO)solution to simulate azo dye wastewater,the decolorization rate of 500 ml MO reached 99.25% under the conditions of 50 mg·L^(-1)initial mass concentration,120 min electrolysis time,15 mA·g^(-1)current density,1 cm electrode spacing,0.1 mol·L^(-1)NaCl,pH 7.6,200 r·min^(-1)rotational speed of the stirrer,and 22-25℃ room temperature.In addition,it is feasible to embroider flexible electronic fabrics with varied sizes and numbers of electrodes based on the amount of treated sewage to increase the degradation rate,which has significant practical application value.

A Research on the Air Permeability of High Polymer Materials Used to Produce Sports Clothing Fabrics

Composite fabrics based on Polytetrafluoroethylene(PTFE)polymer displays several notable properties.They are waterproof,windproof,permeable to moisture and thermally insulating at the same time.In the present study,PTFE fibers are used as raw material to make fiber membranes.The film is formed by crisscrossing interconnected fiber filaments and the related air permeability:tensile creep characteristics and other properties are tested.The results show that the pore size,thickness,and porosity of the film itself can affect the moisture permeability of the film.The water pressure resistance of the selected fabric is 8.5 kPa,and the moisture permeability is 7038 g/(m^(2)·24 h).

The Effects of Dyeing and Finishing Pretreatment Process to the Sliver Fiber Shielding Fabric and the Reasons

Through the silver fiber and cotton mixed silver fiber shielding fabric,not only soft and comfortable,it can wear personal,but also has excellent anti electromagnetic shielding effect. Fabric in dyeing and finishing process,may cause some damage on the silver fiber,influence the shielding performance of shielding fabric. Therefore,in this paper,through the experimental and analysis,find dyeing and finishing process may affect silver fiber shielding fabric and the reasons.

中国废旧军服面料回收利用的研究现状及发展前景

为促进废旧军服面料的高值化回收利用,总结了国内07式军服的种类及其面料特征,系统分析了目前开纤纺纱法、再生聚酯切片法、涤棉分离技术等废旧军服面料的回收利用方法,并对废旧军服面料回收再利用的发展前景进行展望。分析表明:目前废旧军服面料的回收利用主要聚焦于简单再利用或回收涤纶组分制备高值再生聚酯切片,较少关注军服面料中其余组分的高值回收利用。针对废旧军服面料中含量相对较高的涤棉混纺面料,采用有效的涤棉分离技术高效分离涤纶和棉纤维,并以此作为原料分别制备再生聚酯切片和再生溶解浆,进一步以再生棉浆粕为原料制备再生纤维素产品将非常有前景。因而,开发高效的涤棉分离、废旧涤纶和棉纤维的高值化利用技术是实现废旧军服面料综合利用的重要发展方向。

玄武岩织物-钢-PVA工程水泥基复合材料单轴受压力学性能研究

本文研究了玄武岩织物和混杂短切纤维(钢纤维及PVA纤维,短切纤维总体积掺量为2%)复合作用对玄武岩织物-钢-PVA工程水泥基复合材料(BTR-HyECC)单轴受压力学性能的影响,并通过圆柱体单轴受压试验测得各试件受压性能指标,并绘制出应力-应变曲线。结果表明:当钢纤维掺量为0%(体积分数,下同)时,随着玄武岩织物的加入,试件的抗压强度、峰值应变以及抗压韧性显著提高;当钢纤维掺量增加到1%时,试件抗压强度和弹性模量达到最大;当钢纤维掺量为1.5%时,试件变形能力和抗压韧性达到最佳。基于试验数据,建立了适用于BTR-HyECC的单轴受压本构方程,拟合曲线与试验曲线吻合较好。

基于纽介堡方程的色纺织物颜色预测

色纺织物由多种色纤维混合织造,其颜色预测过程复杂,基于格拉斯曼色光混合理论和印刷网点的纽介堡方程,建立了便于计算的颜色预测模型。预测过程分2种情况讨论,一种是取决于表面一层色纤维,另一种是取决于最上面2层纤维相互作用。当考虑最上面2层纤维相互叠加时,相互堆叠简化为与同色堆叠或与两色堆叠。根据不同方式各自建立颜色预测模型,选出预测色差最小的模型并对其优化。结果表明:当以色纺织物最上面2层纤维堆叠组成的色元对混色织物颜色预测时,2层纤维组分不同,认为堆叠顺序对该色元颜色值无影响建立的模型预测色差最小,且对该模型中各色元占比面积系数进行一阶线性回归修正后能较好地用于色纺织物表面颜色值的预测。

石墨烯纤维及其改性纺织品的研究进展

石墨烯纤维是由石墨烯纳米片层在一维受限空间中组装而成的材料,具有优异的力学性能、电学性能和热学性能。石墨烯纤维的制备方法主要包括湿法纺丝、电纺丝和化学气相沉积等技术。石墨烯改性织物的制备方法多样,常用的有直接浸轧还原法、复配液整理法、涂布法、水热法和化学气相沉积法等。其中,直接浸轧还原法通过将织物浸泡在石墨烯氧化物溶液中,然后还原形成石墨烯膜;复配液整理法是将石墨烯与其他功能材料混合后处理织物;涂布法是将石墨烯涂布在织物表面;水热法利用高温高压条件下石墨烯的生长和沉积;化学气相沉积法则是在气相中通过化学反应沉积石墨烯膜。石墨烯纺织品目前在智能穿戴设备、抗菌防臭、导电导热等领域展现出广阔的应用前景。

“无机粒子-无纺布”协同改性碳纤维复合材料及其增韧机理

针对碳纤维复合材料层间性能较差、易发生分层损伤的问题,提出一种采用SiC粒子和热塑性共聚酰胺(PA)无纺布对碳纤维/环氧树脂基复合材料(CFRP)进行增韧改性的技术,在层间构筑一种“无机颗粒/热塑性纤维/树脂基体”多组分多尺度增韧相体系,对比分析改性前后复合材料的Ⅰ型、Ⅱ型层间断裂韧性和耐热性,借助扫描电子显微镜(SEM)和动态热机械分析仪揭示其增韧和耐热性机制。结果表明,与未改性的CFRP材料相比,当SiC填充量(质量分数)为1%、PA无纺布面密度为25 g/m2时,改性CFRP材料Ⅰ型层间断裂韧性(GⅠC)和Ⅱ型层间断裂韧性(GⅡC)分别提高了52.7%和222.6%。无机粒子的阻滞效应、纤维的桥连效应和基体树脂的塑性变形是其主要增韧机制。

熔丝制造3D打印CFRP层内损伤破坏机理与模型研究

为将3D打印技术应用到桥梁工程中,以熔丝制造3D打印碳纤维复合材料锚环为研究对象,开展了材料层内损伤失效机理的基础性研究工作.首先,对锚环进行了张拉锚固破坏试验,明晰材料的损伤失效模式.其次,测试分析了材料的弹性参数及强度参数值,供后续仿真分析使用.最后,通过VUMAT子程序构建了材料的损伤失效本构关系,利用ABAQUS仿真分析软件模拟熔丝制造3D打印碳纤维复合材料锚环的渐进损伤失效全过程,分析其层内损伤失效机理.结果表明:熔丝制造3D打印碳纤维复合材料具有显著的层内损伤现象;选用Hashin损伤起始判据与刚度瞬间退化模型作为熔丝制造3D打印碳纤维复合材料损伤力学模型偏于安全,具有一定的可行性;锚环在高度方向产生纵向裂纹是由纤维拉伸失效导致的.

过滤吸油用PP/PE双组分熔喷非织造布的性能测试研究

以不同质量比的聚丙烯(PP)、聚乙烯(PE)为原料制得PP/PE双组分熔喷非织造布,测试分析了PP/PE双组分熔喷非织造布的性能。结果表明:PP/PE双组分熔喷非织造布的纤网呈现蓬松杂乱的三维结构,纤维直径较细,孔隙率较高;随着PE添加比例增大,PP/PE双组分熔喷非织造布的面密度和厚度增大,拉伸断裂强力、顶破强力略有下降,硬挺度下降,透气性增大;当PP/PE质量比为73时,PP/PE双组分熔喷非织造布的水接触角在129°左右,吸油倍数为18.75,20 s内吸油高度为1.7 mm,空气过滤效率为56.82%,综合性能较好,可应用于过滤、吸油等领域。