Adaptive Reclosing Scheme Based on Traveling Wave Injection For Multi-Terminal dc Grids

The hybrid dc circuit breaker(HCB)has the advantages of fast action speed and low operating loss,which is an idealmethod for fault isolation ofmulti-terminal dc grids.Formulti-terminal dc grids that transmit power through overhead lines,HCBs are required to have reclosing capability due to the high fault probability and the fact that most of the faults are temporary faults.To avoid the secondary fault strike and equipment damage that may be caused by the reclosing of the HCB when the permanent fault occurs,an adaptive reclosing scheme based on traveling wave injection is proposed in this paper.The scheme injects traveling wave signal into the fault dc line through the additionally configured auxiliary discharge branch in the HCB,and then uses the reflection characteristic of the traveling wave signal on the dc line to identify temporary and permanent faults,to be able to realize fast reclosing when the temporary fault occurs and reliably avoid reclosing after the permanent fault occurs.The test results in the simulation model of the four-terminal dc grid show that the proposed adaptive reclosing scheme can quickly and reliably identify temporary and permanent faults,greatly shorten the power outage time of temporary faults.In addition,it has the advantages of easiness to implement,high reliability,robustness to high-resistance fault and no dead zone,etc.

Stability Analysis of a Multi Area System with Renewable Energy and Multi-Terminal DC Tie Lines

Security constrained multi area multi objective dynamic economic dispatch (SCMAMODED) with renewable energy (RE) and all the possible MTDC stability constraints is formulated for the first time. The stability merits of multi terminal DC (MTDC) tie lines as compared to the traditional HVAC forms the main objective of this paper. Probabilistic load flow (PLF) is applied to determine the system parameters while the uncertainties are modelled using Scenario Based Method (SBM). The simulation results reveal that with the use of MTDC tie lines, the frequency and voltage stability in the MAMODED with renewable energy sources (RES) are enhanced while keeping the MTDC power exchange interface nodes at secure levels.

基于谐振型DCX的部分功率调节技术研究综述

以LLC为代表的谐振变换器具有良好的软开关性能以及高效功率传输优势,但是开关频率的改变会使得谐振点发生偏移,效率显著降低,直流变压器(DC transformer, DCX)工作状态虽有利于实现效率优化,但却限制了系统的电压调节范围。此外,传统全功率传输会导致器件应力高,存在效率优化局限。近年来,部分功率传输由于低应力、高效率以及控制简单等优势得到广泛的应用,将谐振变换器与部分功率技术结合,强化优势互补,提高应用价值,已成为目前的研究热点。文中从部分功率传输概念和基本连接形式入手,对基于谐振型DCX的部分功率调节系统结构进行归纳分析,概括为单级式、两级式以及准两级式3种结构类型,讨论分析适用于不同种类结构的变换器拓扑以及控制方式;其次,对目前所实现的部分功率调节系统所能达到的性能指标进行归纳,并对传统两级级联式结构和另外3种部分功率调节结构的器件数量、电压增益以及工作效率进行综合分析对比;最后,对不同结构的优缺点和应用局限性进行总结,并对未来发展趋势展望,为后续研究提供一定的参考。

Research on DC Protection Strategy in Multi-Terminal Hybrid HVDC System

Multi-terminal hybrid high-voltage direct current(HVDC)systems have been developed quickly in recent years in power transmission area.However,for voltage-source converter(VSC)stations in hybrid HVDC systems,no direct current(DC)filters are required.In addition,the DC reactor is also not installed at the line end because the DC fault can be limited by the converter itself.This means that the boundary element at the line end is absent,and the single-ended protections used in line commutated converter(LCC)based HVDC(LCC-HVDC)systems or VSC-HVDC systems cannot distinguish the fault line in multi-terminal hybrid HVDC systems.This paper proposes a novel singleended DC protection strategy suitable for the multi-terminal hybrid HVDC system,which mainly applies the transient information and active injection concept to detect and distinguish the fault line.Compared with the single-ended protections used in LCC-HVDC and VSC-HVDC systems,the proposed protection strategy is not dependent on the line boundary element and is thus suitable for the multiterminal hybrid HVDC system.The corresponding simulation cases based on power systems computer aided design(PSCAD)/electromagnetic transients including DC(EMTDC)are carried out to verify the superiority of the proposed protection.

Analysis and Control of Modular Multi-terminal DC Power Flow Controller with Fault Current Limiting Function

In order to overcome the problems of power flow control and fault current limiting in multi-terminal high voltage direct current(MTDC)grids,this paper proposes a modular multi-terminal DC power flow controller(MM-DCPFC)with fault current limiting function.The topology structure,operation principle,and equivalent circuit of MM-DCPFC are introduced,and such a structure has the advantages of modularity and scalability.The power balance mechanism is studied and a hierarchical power balance control strategy is proposed.The results show that MM-DCPFC can achieve internal power exchange,which avoids the use of external power supply.The fault characteristics of MM-DCPFC are analyzed,fault current limiting and self-protection methods are proposed,and the factors affecting the current limiting capability are studied.The simulation models are established in PLECS,and the simulation results verify the effectiveness of MM-DCPFC in power flow control,fault current limiting,and scalability.In addition,a prototype is developed to validate the function and control method of MM-DCPFC.

Research on DC Fault of Multi-Terminal Direct Current System

This paper introduces the characteristics of VSC and MMC-MTDC and discusses the effects of different kinds of faults in HVDC systems. Special attention is given to the comparison between a pole-to-pole fault and a pole-to-ground fault occurring in the middle of the line or at the terminal of a VSC. Simulations using MATLAB are provided in this article which show the difference effects clearly when faults occur in a VSC-MTDC system or in a MMC-MTDC system. Understanding of such fault characteristics and the influence of the control system on them are important prerequisites on the way to MTDC systems.

18万t/a双氧水装置中集散控制系统DCS及兼容SIS与GDS应用

利用国内先进的浙大中控成熟的DCS为软硬件控制平台,将其应用到18万t/a双氧水生产装置中。在阐述系统应用方案的基础上,提出了技术关键点,详述了DCS系统在双氧水装置中控制系统的软、硬件构成和控制方案及组态等。DCS系统软硬件综合调试并投运,整个生产过程稳定、可靠、产品合格率较高,达到了预期设计目标。

Applying Power Margin Tracking Droop Control to Flexible Operation in Multi-terminal DC Collector Systems of Renewable Generation

An emerging multi-terminal looped DC(MTDC)collector system is now advocated for collecting and transferring large-scale renewable generation.However,it remains an open question as to improving the cooperative control capability of looped converter stations for flexible and robust response to renewable grid-connection fluctuation.This paper addresses this problem with a novel Power Margin Tracking(PMT)droop control and its corresponding system-level control strategy from the perspective of optimal dispatch of the power system.By introducing a power margin correction factor into the droop coefficient,the converter station can make self-adaptive regulations according to its actual available power margin.For operation verification,a multi-period optimal operation model and a four-terminal simulation model is built to provide optimal control parameters and real-time operation states of converter stations,where the power flow model of the looped MTDC grid with renewables generation is considered.The case results prove that the proposed control strategy can improve the cooperative operation capability of multiple converter stations,mitigating grid-connected power fluctuation.It can effectively reduce the DC voltage deviation to enhance the operation stability of the MTDC grid.The operational robustness of the proposed control strategy under“N−1”fault cases is verified as well.

一种交叉倍压型高增益DC/DC变换器

针对光伏发电、燃料电池发电等领域对高增益直流变换器的需求,以两相交错并联升压变换器为研究对象,由2个含有电感的倍压单元组合设计出实现电压提升的交叉倍压结构,据此提出了一种新颖的交叉倍压型高增益DC/DC变换器。该变换器可实现(3n+4)/(1-d)倍的高电压增益(1∶n为耦合电感匝数比,d为变换器占空比),且具有电路器件的低电压应力特性。对于漏感引起的开关管电压尖峰问题,引入了钳位电容构成释放漏感能量通道,同时提升了输出电压。介绍了新型交叉倍压型高增益变换器的拓扑结构,分析了变换器各模态的工作过程,推导了电压增益、输入电流纹波及各器件电压应力等稳态特性,并搭建样机进行实验研究,验证了该直流变换技术方案的可行性和先进性。

单级三相谐波电流注入可升降压AC/DC变换器

为适应电动车充电电压宽范围变化需求,本文针对传统充电桩前级整流器拓扑开展研究,提出一种新式单级三相AC/DC变换器。该变换器集成了三相桥式不控整流电路与Cuk模块,为降低输入侧电流谐波分量,选用双向开关管构建谐波电流回馈通路,整体构造成单级式拓扑结构。文章阐述了变换器的电路结构及工作模态,通过建立变换器的等效模型推导出电压增益。变换器通过简单的控制逻辑即可实现正弦输入电流并拥有高功率因数。最后通过搭建变换器数字控制实验平台验证了所提变换器的可行性。

模块化高压大容量DC/DC变换器综述

随着新能源发电占比增加和电网规模的不断扩大,直流输电系统的容量不断提升,含有不同电压等级的直流电网是未来发展的必然趋势。在此背景下,DC/DC变换器作为直流电网关键设备,在多电压等级互联场景中发挥着重要作用。文中首先对已有的模块化高压大容量DC/DC变换器进行归纳、分类和比较,然后阐述了目前模块化高压大容量DC/DC变换器的拓扑结构、工作原理与特点,并针对其特点提出了不同变换器的适用场景,最后对未来的研究方向提出了建议。

摇摆、时间压力对DCS操作员监视绩效和工作负荷的影响

为了解摇摆、时间压力对数字化控制系统(DCS)操作员监视作业的影响,降低人因失误,设计监视试验获得摇摆(静止、低和高)和时间压力(无时间压力和有时间压力)条件下操作员监视绩效和工作负荷;运用统计学方法分析摇摆和时间压力对监视绩效和工作负荷的影响。结果表明:摇摆对监视绩效(监视时间和正确率)和工作负荷影响均不显著,但随着摇摆级别的增加,监视时间和工作负荷呈现上升趋势;时间压力显著影响监视时间和工作负荷,但对正确率影响不显著;监视任务中,状态确认任务用时显著多于数据比较任务,但正确率差异不显著。摇摆条件下DCS操作员监视绩效和工作负荷与静止条件基本一致;有时间压力条件下,DCS操作员监视工作负荷较大,但监视时间较短。

固态变压器中隔离双向DC/DC变换器扩展移相下虚拟电流控制策略

该文以固态变压器后级隔离双向DC/DC变换器为重点研究对象,提出一种扩展移相下虚拟电流控制策略。通过分析后级变换器在扩展移相传输功率下相移量关系以获得最小电流应力最优解来提高变换器的传输效率,减少器件损耗。同时通过虚拟电流控制思想在线估算传输功率来提高系统动态响应性能,减少电流传感器使用。最后,对该文所提出的扩展移相下虚拟电流控制与扩展移相控制进行实验对比分析,验证了扩展移相下虚拟电流控制策略具有降低电流应力,显著提高变换器的动态响应的优点。

一种可拓展双输入高增益DC/DC变换器

针对光伏发电系统中光伏电池板集成汇流的需求,提出了一种可拓展双输入高增益DC/DC变换器。该变换器采用了一种新型拓扑结构,可在实现输入输出电压高增益变换的同时降低了开关器件的电压应力。此外,所提变换器还具有可拓展性,可以根据不同的光伏电池板数量和输出电压要求对端口进行扩展,从而降低系统的复杂性和成本。首先详细介绍了所提变换器的拓扑结构,并推导出变换器在不同工作模态下的运行原理。然后,对该变换器的增益特性、开关器件的电压和电流应力、关键器件的参数选择和损耗计算等方面进行了深入的理论分析。最后,搭建了一台输出功率为1 kW的实验样机,并进行了实验测试。实验结果验证了所提变换器理论分析的正确性和可行性。

基于MPC的耦合电感飞跨电容双向DC/DC变换器功率均衡解耦控制策略

耦合电感功率变换器因耦合电感阻抗、电感值等参数差异易导致功率不均衡。针对耦合电感飞跨电容双向DC/DC变换器,提出一种基于模型预测控制(MPC)的功率均衡解耦控制策略。通过对变换器原理进行分析,建立基于电感电流解耦的数学模型,得到包括电感电流和飞跨电容电压等6个控制变量的解耦控制方法。在此基础上,提出基于MPC的功率均衡解耦控制策略。同时,为降低MPC算法的运算负荷,根据解耦控制模型重构模型预测价值函数,实现各控制变量独立动态寻优,使系统能在稳定控制输出电压及飞跨电容电压的同时,实现两相耦合电感的功率均衡控制。最后,通过理论分析及实验对所提策略进行有效验证。

三有源桥DC-DC变换器广义状态空间平均模型及控制策略研究

基于移相加占空比控制策略的三有源桥TAB(triple active bridge)DC-DC变换器具有效率高和软开关范围可扩展等优点,但其小信号建模过程复杂、闭环控制环路参数整定困难。针对该问题,提出1种TAB工作在移相加占空比控制下的全阶连续广义状态平均建模和PI控制器设计方法。首先,分析TAB的运行原理和Y型等效结构;然后,结合移相加占空比控制的特点和交流方波源等效方法,推导出TAB的广义状态空间平均模型;接着,在推得模型的基础上求得输入到输出的传递函数,设计出PI控制器参数。最后,结合数字仿真及样机实验验证了所提方法的正确性及有效性。

DCS控制器中电表接触传感器计量误差检测方法

由于DCS控制器中电表传感器在计量检测过程中,传统的B-MAC-DCS协议能耗和丢包率较高,无法缓解汇聚节点的漏斗效应,导致在远程抄表过程中传感器计量误差增大。提出一种机械电表接触传感器计量误差检测方法。采用小波基函数对DCS控制器中的接触传感器计量数据抗干扰处理,并通过动态选取阈值的方法,对经过小波变换后的数据去除噪声。使用低功耗自适应集簇分层型(low energy adaptive clustering hierarchy,LEACH)协议分簇代替传统的B-MAC协议;根据簇内监测值,引入阈值分析方法获取传感器计量指标,并将其作为判定依据进行误差检测,根据计量指标的变化情况判断是否存在计量误差。实验结果表明,所提方法可以准确且有效检测出机械电表接触传感器计量误差,解决DCS中机械电表的运行隐患问题。

基于SEPIC的新型高增益DC-DC变换器及衍生拓扑分析

针对光伏并网系统中单开关升压变换器(如SEPIC、Boost、准Z源、二次型)电压增益低和半导体器件电压应力大的问题,提出1种基于SEPIC的外部升压型高增益DC-DC变换器。首先对所提变换器在电感电流连续导通模式和断续导通模式下的工作原理和稳态特性进行详细分析,并与其他新型拓扑进行性能对比。在此基础上,给出了基于外部升压网络的衍生拓扑。最后,通过搭建1台400 V/200 W的实验样机证明了理论分析的准确性。所提变换器利用阻抗网络和开关电容单元构成的外部升压网络提升了SEPIC变换器的电压增益,并改善了半导体器件电压应力大的缺点。

基于数字PWM控制的Buck型DC/DC变换器设计

为解决集成电路生产成本随半导体制造工艺进步而升高的问题,尤其针对传统模拟架构DC/DC变换器中的电阻、电容、运算放大器等模块面积大、功耗高、稳定性差等问题,设计一款基于数字PWM调制buck型DC/DC变换器。设计基于CSMC 0.18μm BCD工艺,使用Verilog硬件描述语言设计数字PID补偿器,在VCS+XA数模混合仿真环境下进行仿真验证。仿真结果表明在不同PVT条件以及不同负载下,输出纹波较低,输出电压稳定,实现了低成本、高鲁棒性的设计目标。