In situ temperature measurement of vapor based on atomic speed selection

We demonstrate an experimental method for the in situ temperature measurement of atomic vapor using the saturated absorption spectrum. By separately manipulating the frequency of the pump and probe beams, the position of the crossover peaks can move along the spectrum. Different velocity classes of atoms contribute to the crossover during the movement. We study the relationship between the intensity change of peaks and vapor temperature. Our experimental result around room temperature shows a deviation of less than 0.3 K. Compared with traditional thermometry using absorption spectroscopy, higher accuracy can theoretically be achieved with real-time thermometry.

Revamping design of an EAF automatic temperature measurement and sampling robot

The function,features,and architecture of a robot that performs automatic temperature measurement and sampling applied on a 150-t AC electric arc furnace(EAF)production line of Baosteel were presented,and the key points of design and revamping experience on the site layout,device protection,lance tool,probe container,measuring position control,and system safety were summarized.Furthermore,a valuable reference for the application of automatic temperature measuring and sampling robots in EAF steelmaking plants will be provided.

TEMPERATURE MEASUREMENT OF REFLECTED SHOCK WAVE BY USING CHEMICAL INDICATOR

This report describes a new method for measuring the temperature of the gas behind the reflected shock wave in shock tube, corresponding to the reservoir temperature of a shock tunnel, based on the chemical reaction of small amount of CF4 premixed in the test gas. The final product C2F4 is used as the temperature indicator, which is sampled and detected by a gas chromatography in the experiment. The detected concentration of C2F4 is correlated to the temperature of the reflected shock wave with the initial pressure P-1 and test time tau as parameters in the temperature range 3 300 K < T < 5 600 K, pressure range 5 kPa < P1 <12 kPa and tau similar or equal to 0.4 ms.

Investigation on the plastic work-heat conversion coefficient of 7075-T651 aluminum alloy during an impact process based on infrared temperature measurement technology

The plastic work-heat conversion coefficient is one key parameter for studying the work-heat conversion under dynamic deformation of materials. To explore this coefficient of 7075-T651 aluminum alloy under dynamic compression, dynamic compression experiments using the Hopkinson bar under four groups of strain rates were conducted, and the temperature signals were measured by constructing a transient infrared temperature measurement system. According to stress versus strain data as well as the corresponding temperature data obtained through the experiments, the influences of the strain and the strain rate on the coefficient of plastic work converted to heat were analyzed.The experimental results show that the coefficient of plastic work converted to heat of 7075-T651 aluminum alloy is not a constant at the range of 0.85–1 and is closely related to the strain and the strain rate. The change of internal structure of material under high strain rate reduces its energy storage capacity, and makes almost all plastic work convert into heat.

Spatial resolved temperature measurement based on absorption spectroscopy using a single tunable diode laser

A novel method based on wavelength-multiplexed line-of-sight absorption and profile fitting for nonuniform flow field measurement is reported. A wavelength scanning combing laser temperature and current modulation WMS scheme is used to implement the wavelength-multi- plexed-profile fitting method. Second harmonic （2f） signal of eight H20 transitions features near 7,170 cm^-1 are measured in one period using a single tunable diode laser. Spatial resolved temperature distribution upon a CH4/air premixed flat flame burner is obtained. The result validates the feasibility of strategy for non-uniform flow field diagnostics by means of WMS-2f TDLAS.

Design of weak current measurement system and research on temperature impact

A dedicated weak current measurement system was designed to measure the weak currents generated by the neutron ionization chamber.This system incorporates a second-order low-pass filter circuit and the Kalman filtering algorithm to effectively filter out noise and minimize interference in the measurement results.Testing conducted under normal temperature conditions has demonstrated the system's high precision performance.However,it was observed that temperature variations can affect the measurement performance.Data were collected across temperatures ranging from -20 to 70℃,and a temperature correction model was established through linear regression fitting to address this issue.The feasibility of the temperature correction model was confirmed at temperatures of -5 and 40℃,where relative errors remained below 0.1% after applying the temperature correction.The research indicates that the designed measurement system exhibits excellent temperature adaptability and high precision,making it particularly suitable for measuring weak currents.

The dating and temperature measurement technologies for carbonate minerals and their application in hydrocarbon accumulation research in the paleouplift in central Sichuan Basin, SW China

A new method for reconstructing the geological history of hydrocarbon accumulation is developed, which are constrained by U-Pb isotope age and clumped isotope((35)47) temperature of host minerals of hydrocarbon-bearing inclusions. For constraining the time and depth of hydrocarbon accumulation by the laser in-situ U-Pb isotope age and clumped isotope temperature, there are two key steps:(1) Investigating feature, abundance and distribution patterns of liquid and gaseous hydrocarbon inclusions with optical microscopes.(2) Dating laser in-situ U-Pb isotope age and measuring clumped isotope temperature of the host minerals of hydrocarbon inclusions. These technologies have been applied for studying the stages of hydrocarbon accumulation in the Sinian Dengying gas reservoir in the paleo-uplift of the central Sichuan Basin. By dating the U-Pb isotope age and measuring the temperature of clumped isotope((35)47) of the host minerals of hydrocarbon inclusions in dolomite, three stages of hydrocarbon accumulation were identified:(1) Late Silurian: the first stage of oil accumulation at(416±23) Ma.(2) Late Permian to Early Triassic: the second stage of oil accumulation between(248±27) Ma and(246.3±1.5) Ma.(3) Yanshan to Himalayan period: gas accumulation between(115±69) Ma and(41±10) Ma. The reconstructed hydrocarbon accumulation history of the Dengying gas reservoir in the paleo-uplift of the central Sichuan Basin is highly consistent with the tectonic-burial history, basin thermal history and hydrocarbon generation history, indicating that the new method is a reliable way for reconstructing the hydrocarbon accumulation history.

Inter-stage line ratio of He- and Li-like Ti emissions for the electron temperature measurement

Under coronal conditions, the steady state rate-equations are used to calculate the inter-stage line ratios between Li-like ls22p(2P3/2)→ls22s(2S1/2) and He-like ls2p(1P1)→1s2(1S0) transitions for Ti in the electronic temperature ranges from 0.1keV to 20 keV. The results show that the temperature sensitivities are higher at the electronic temperature less than 5000 eV and the temperature sensitivities will decrease with the increase of electronic temperature.

The Design of Fiber Bragg Grating Temperature Measurement System Based on Labview

The paper made a research on the fiber Bragg grating sensor demodulation system, which was based on virtual instrument labview and it developed a friendly upper monitor software. Based on the LM algorithm, the software realized rapid and accurate spectral data fitting, improving dynamic characteristics and measuring precision of the system. Depending on different fiber Bragg grating sensors, it can realize flexible calibration. It has the functions of collection, display and data storage, which can flexibly design alarm threshold according to the practical application. The fiber Bragg grating sensors can be identified by the software so that the distributed network, with large capacity optical fiber sensing, can be achieved.

Design of Distributed Temperature Measurement System for Switchgear

This paper develops a novel distributed temperature measurement system based on DSP and DS18B20 digital thermometer. The real-time temperature of each node in the switchgear is obtained by several DS18B20s which are connected on the 1-wire bus together. RS-485 master-slave communication protocol is used to centralize monitoring temperatures of several switchgear cabinets. The system also has the function of temperature alarm. The operation of simulation experiment has showed that the system is able to complete monitoring real-time temperatures in high voltage switchgear.

Petrography, Temperature Measurement, and Economic Evaluation of Granitoid Pluton of Qohrud-Kashan Using EPMA, XRD, and XRF Analysis

The area which is being studied is located in northwest of Isfahan, 30 kilometers south of Kashan, and southern section of Qmasar. The longitude of the area of study is 51°19'13"E to 51°26'26"E and its latitude is 33°34'24"N to 33°44'24"N. Based on microscopic observations, modal analysis, and also based on their location in the Streckeisen [QAPF], both the stones of the Qohrud batholitic mass themselves and its enclaves are more in quartz monzonite ranges. Granitoid also have quartz monzonite enclaves. These enclaves are from both microgranular mafic and Autolith types which indicate the mixing of two magmas. At the center of the pluton, there are indications of existence of main magma reservoir and magma mixing. In terms of mineralogy, the granitoid rocks of the area very much resemble I-type. The zoning of the plagioclases is both the normal kind and variation invert and has andesine general composition. The probed biotite sample contains iron and belongs to a granitic sample from the center of the mass. Also, the ranking graph indicates biotite as the source of recrystallization for the analyzed points. The probed biotite sample of the Qohrud area showed formation temperature of 730 degrees centigrade. According to the Rb and Sr contents, the source of the rocks is at depths of 20 to 30 kilometers from the earth’s surface that are depending on the subduction zone. The formation temperature of the specimens of the Qohrud batholithic mass is mostly between 900 to 1000 degrees centigrade. [At] the center of the mass (around Qahrud), the amount of molybdenum is higher than the economic limit.

Temperature Measurement of Air Flow Using Fluorescent Mists Combined with Two-Color LIF

This study proposes a two-color laser-induced fluorescence (LIF) technique for measuring the temperature distribution of an airflow by spraying a mist of a fluorescent dye. The mist is generated by using propylene glycol, the vapor pressure of which is much lower than that of water, as the solvent of the fluorescent dyes. A supersonic moisture chamber is used as the atomizer for seeding the tracer particles to be visualized. The proposed technique is applied to the measurement of the temperature distribution in a thermal vertical buoyant plume. The proposed two-color LIF thermometry is found to be very effective for the study of such a thermal structure, and it is well suited for measuring the temperature field of an airflow.

Estimation of Glacier Melt Water Contribution for Human Consumption in the Royal Andes Considering Temperature Measurement Errors

Glaciers from the West side of the Royal Andes are an important source of fresh water for some of the most important Bolivian cities like El Alto. Temperature is an important datum for hydrological modelling and for glacier melt estimation. All temperature measurement devices have some degree of uncertainty due to systematic errors;thus, any temperature measurement has some errors. It is important to estimate the influence of such errors on the results from hydrological models and the estimation of melt water. The present study estimates the melt water contribution from the glaciers Tuni and Huayna West as a source of water supply for human consumption of El Alto considering the errors from temperature measurements. The hydrologic response of the basins was simulated with a hydrologic model. The glacier melt contribution was estimated as the difference between the discharge from the current scenario (with glaciers) and the discharge from a scenario without glaciers. Several volumes of melt water were estimated considering the temperature measurement and its possible errors. The uncertainty of such melt water volume was addressed by performing a Monte Carlo analysis of the possible melt water. The melt water contribution from glacier Tuni and Huayna West during the hydrologic year 2011-2012 was between 1.37 × 106 m3 and 1.72 × 106 m3. Such water volume is enough to meet the yearly water demand of between 6.81% and 8.55% of El Alto.

Spatial pattern recognition for near-surface high temperature increases in mountain areas using MODIS and SRTM DEM

Abrupt near-surface temperature changes in mountainous areas are a special component of the mountain climate system.Fast and accurate measurements of the locations,intensity,and width of the near-surface changes are necessary but highly difficult due to the complicated environmental conditions and instrumental issues.This paper develops a spatial pattern recognition method to measure the near-surface high temperature increase(NSHTI),one of the lesser-attended changes.First,raster window measurement was proposed to calculate the temperature lapse rate using MODIS land surface temperature and SRTM DEM data.It fully considers the terrain heights of two neighboring cells on opposite or adjacent slopes with a moving window of 3×3 cell size.Second,a threshold selection was performed to identify the NSHTI cells using a threshold of-0.65℃/100 m.Then,the NSHTI strips were parameterized through raster vectorization and spatial analysis.Taking Yunnan,a mountainous province in southwestern China,as the study area,the results indicate that the NSHTI cells concentrate in a strip-like pattern along the mountains and valleys,and the strips are almost parallel to the altitude contours with a slight northward uplift.Also,they are located mostly at a 3/5 height of high mountains or within 400 m from the valley floors,where the controlling topographic index is the altitude of the terrain trend surface but not the absolute elevation and the topographic uplift height and cutting depth.Additionally,the NSHTI intensity varies with the geographic locations and the proportions increase with an exponential trend,and the horizontal width has a mean of about 1000 m and a maximum of over 5000 m.The result demonstrates that the proposed method can effectively recognize NSHTI boundaries over mountains,providing support for the modeling of weather and climate systems and the development of mountain resources.

The definition analyses of radiation temperature measurement area

In the research of primary spectrum pyrometry, this paper discussed the definition problem of radiation temperature measurement area based on the measurement coordinates. For the linear spectrum emissivity model and improved monotonic spectrum emissivity model, the characteristics of radiation temperature measurement area restricted by the measurement coordinates were theoretically analyzed, through the investigations of the temperature and emissivity coordinate axes. Choosing the specific primary spectrum pyrometer as an example in applications, the theoretical area of radiation temperature measurement of this pyrometer was given and it was verified through blackbody experiments. The discussions of this paper will provide the necessary foundation for the theory research development of primary spectrum pyrometry and the realization of technical applications.

A technique utilizing chemical reagents for direct measurement of temperature at a local area and its engineering applications

Temperature is one of the physical quantifies through which quantitative evaluation of the safety and reliability of industrial products can be achieved, and this has been used widely in practice. Under any environmental condifion, regardless of the size of the object to be inspected, accurate and reliable measurement of temperature is of great practical importance. This review article presents a simple and direct method of temperature measurement, that can be applied to the local areas with difficulty in measuring the temperature by using normal thermometers. In the present article, two different application examples are demonstrated. One addresses the study of the electromigration of solders which are used as bonding metals in electronic devices （micro-structures）. The application of the method to the shaft of a motor used in heavy industrial fields is explained as the second.

Measurements of non-equilibrium and equilibrium temperature behind a strong shock wave in simulated martian atmosphere

Non-equilibrium radiation measurements behind strong shock wave for simulated Martian atmosphere are presented in this paper. The shock wave is established in a hydrogen oxygen combustion driven shock tube. Time- resolved spectra of the Av = 0 sequence of the B^2∑^＋ → X^2∑^＋ electronic transition of CN have been observed through optical emission spectroscopy （OES）. A new method, which is based on fitting high resolution spectrum for rotational and vibrational temperatures measurement, is proposed to diag- nose temperature distribution behind the shock wave. It is estimated that the current scheme has the maximum deviation less than 8% （lσ） for vibrational temperature measurement through detailed analysis of the influence of the uncertainties of spectroscopic constants and spectral resolution. Radiation structure of the shock layer, including induction, relaxation and equilibrium process, and corresponding rotational and vibrational temperatures are obtained through time gating OES diagnostics with sub-microsecond temporal resolution. The present extensive results will strongly benefit the reaction rate estimation and computational fluid dynamics （CFD） code validation in high enthalpy Mars reentry chemistry.

Effect Factors on Measurement Precision of the Embedded Temperature Sensing Fabric

The embedded temperature sensing fabric was designed and woven according to the heat transmission model of the fabric.The temperature sensors were embedded into the multi-layered fabric that weft yarns were high-shrinkage polyester filaments.And the fabric was treated by a self-designed partial heat device,which can make the sensor be fixed in the fabric.The effects of yarn type,yarn linear density,fabric warp density,fabric structure,fabric layer numbers where the sensor is located,and the ambient temperature on the temperature measured value were investigated.The results demonstrated that when the higher thermal conductivity of yarns and lower density yarns were applied in the fabric as rawmaterials,they were favored to improve the measurement precision.Meanwhile,there were many factors that could make the measured values closer to the real value of the body,such as the plain fabric,the increased warp density of the fabric,the multiple-layer fabric where the sensor was located,the raised ambient testing temperature and the prolonged test time in the certain range.