Na_(3)V_(2)(PO_(4))_(3)(NVP)cathode material of the sodium ion battery(1 C=117 mAh g-1)has a NASICON-type structure,which not only facilitates the rapid migration of sodium ions,but also has a small volume deformation...Na_(3)V_(2)(PO_(4))_(3)(NVP)cathode material of the sodium ion battery(1 C=117 mAh g-1)has a NASICON-type structure,which not only facilitates the rapid migration of sodium ions,but also has a small volume deformation during sodium ion de-intercalation and the main frame mechanism remains unchanged,and thus is seen as an energy storage material for a wide range of applications,but has a limited electronic conductivity due to its structure.In this paper,NVP cathode materials with finer primary particles are successfully prepared using a simple hydrothermal treatment-assisted sol-gel method.The increased pore size of the NVP materials prepared under the hydrothermal process allows for more active sites and more effective resistance to the volume deformation of sodium ions during insertion/extraction processes,effectively facilitating the diffusion of ions and electrons.The Na_(3)V_(2)(PO_(4))_(3) material obtained by the optimized process exhibited good crystallinity in XRD characterization,as well as superior electrochemical properties in a series of electrochemical tests.A specific capacitance of 106.3 mAh g^(-1) at 0.2 C is demonstrated,compared to 96.5 mAh g^(-1) for Na_(3)V_(2)(PO_(4))_(3) without hydrothermal treatment,and cycling performance is also improved with 93%capacity retention.The calculated sodium ion diffusion coefficient(DNa=5.68×10^(-14))obtained after EIS curve fitting of the improved sample illustrates that the pore structure is beneficial to the performance of the Na_(3)V_(2)(PO_(4))_(3)cathode material.展开更多
通过简单的溶胶-凝胶辅助静电纺丝法得到(113)晶面优势导向的Na_3V_2(PO_4)_3/C钠离子电池正极材料,并通过对比最佳纺丝条件下分别用聚乙烯吡咯烷酮(PVP)和聚氧化乙烯(PEO)作为晶面导向剂制备的两种Na_3V_2(PO_4)_3电极材料的电化学性能...通过简单的溶胶-凝胶辅助静电纺丝法得到(113)晶面优势导向的Na_3V_2(PO_4)_3/C钠离子电池正极材料,并通过对比最佳纺丝条件下分别用聚乙烯吡咯烷酮(PVP)和聚氧化乙烯(PEO)作为晶面导向剂制备的两种Na_3V_2(PO_4)_3电极材料的电化学性能,证明静电纺丝有利于实现Na_3V_2(PO_4)_3(113)晶面择优取向。在相同的电流密度(0.1 C)下,NVP-PVP和NVP-PEO的首周放电比容量分别为112.5 m A·h/g和96.3 m A·h/g,电池循环50周后,NVP-PVP仍然有98.1 m A·h/g的可逆容量保持,NVP-PEO仅仅只剩下34 m A·h/g的可逆容量保持,而即使循环100周后,NVP-PVP的可逆容量仍然在88.2 m A·h/g。结果表明,PVP静电纺丝有利于构建特定的纳米纤维结构和均一的导电碳网络骨架,进而提升主体材料Na_3V_2(PO_4)_3的电化学性能。展开更多
采用溶胶凝胶-高温固相法,用不同的钠源制备NASICON结构钠离子电池正极材料Na_3V_2(PO_4)_3.借助扫描电子显微镜(SEM),X射线衍射分析(XRD),电池测试系统及电化学工作站对制备的Na_3V_2(PO_4)_3结构,形貌,电性能和内阻进行表征.研究结果...采用溶胶凝胶-高温固相法,用不同的钠源制备NASICON结构钠离子电池正极材料Na_3V_2(PO_4)_3.借助扫描电子显微镜(SEM),X射线衍射分析(XRD),电池测试系统及电化学工作站对制备的Na_3V_2(PO_4)_3结构,形貌,电性能和内阻进行表征.研究结果表明,以Na_2CO_3为钠源合成Na_3V_2(PO_4)_3有更好的颗粒尺寸,形貌结构完整,充放电性能及循环稳定性更好,阻抗也较小;在2.5~4.0 V电压范围内,以0.2C进行充放电,首次放电比容量达到110.8 m Ah/g,50次循环后容量保持率为85.1%.展开更多
Sodium-ion batteries （SIBs） have attracted increasing attention in the past decades, because of high over-all abundance of precursors, their even geographical distribution, and low cost. Na3V2（PO4）3 （NVP）, atypi...Sodium-ion batteries （SIBs） have attracted increasing attention in the past decades, because of high over-all abundance of precursors, their even geographical distribution, and low cost. Na3V2（PO4）3 （NVP）, atypical sodium super ion conductor （NASlCON）-based electrode material, exhibits pronounced structuralstability, exceptionally high ion conductivity, rendering it a most promising electrode for sodium storage.However. the comparatively low electronic conductivity makes the theoretical capacity of NVP cannot befully accessible even at comparatively low rates, presenting a major drawback for further practical ap-plications, especially when high rate capability is especially important. Thus, many endeavors have beenconformed to increase the surface and intrinsic electrical conductivity of NVP by coating the active mate-rials with a conductive carbon layer, downsizing the NVP particles, combining the NVP particle with vari-ous carbon materials and ion doping strategy. In this review, to get a better understanding on the sodiumstorage in NVP, we firstly present 4 distinct crystal structures in the temperature range of-30℃-225℃ namely α-NVP, β-NVP, β′-NVP and γ-NVP. Moreover, we give an overview of recent approaches to en-hance the surface electrical conductivity and intrinsic electrical conductivity of NVP. Finally, some poten-tial applications of NVP such as in all-climate environment and PHEV, EV fields have been prospected.展开更多
The modification effects of ytterbium(Yb), Na_3PO_4 and Yb + Na_3PO_4 on primary Mg_2Si phase in Mg-4Si alloys were investigated by means of X-ray diffraction(XRD), optical microscopy(OM), scanning electron microscopy...The modification effects of ytterbium(Yb), Na_3PO_4 and Yb + Na_3PO_4 on primary Mg_2Si phase in Mg-4Si alloys were investigated by means of X-ray diffraction(XRD), optical microscopy(OM), scanning electron microscopy(SEM) and energy dispersive spectroscopy(EDS) analysis in this work. The results indicate that the morphology of the primary Mg_2Si phase apparently changes from coarse dendrites to fine dispersive polygonal particles and the mean size decreases from 276.6 μm to 7.1 μm, with combined modification of 0.8wt.% Yb and 2.64 wt.% Na_3PO_4. Such a morphological evolution results in improvement in the ultimate tensile strength and elongation of the alloys as compared to the base alloy. This may be attributed to the formation of the YbP particles that acted as the heterogeneous nucleation substrates for the primary Mg_2Si particles, resulting in a refined distribution of these precipitates. The results of XRD examination show that there was no reaction between Si and Yb or Na_3PO_4. Solo addition of Yb or Na_3PO_4 into the melt has no real modification effect on the microstructure, but the primary Mg_2Si particles and α-Mg phases become coarser than that in the unmodified alloy.展开更多
文摘Na_(3)V_(2)(PO_(4))_(3)(NVP)cathode material of the sodium ion battery(1 C=117 mAh g-1)has a NASICON-type structure,which not only facilitates the rapid migration of sodium ions,but also has a small volume deformation during sodium ion de-intercalation and the main frame mechanism remains unchanged,and thus is seen as an energy storage material for a wide range of applications,but has a limited electronic conductivity due to its structure.In this paper,NVP cathode materials with finer primary particles are successfully prepared using a simple hydrothermal treatment-assisted sol-gel method.The increased pore size of the NVP materials prepared under the hydrothermal process allows for more active sites and more effective resistance to the volume deformation of sodium ions during insertion/extraction processes,effectively facilitating the diffusion of ions and electrons.The Na_(3)V_(2)(PO_(4))_(3) material obtained by the optimized process exhibited good crystallinity in XRD characterization,as well as superior electrochemical properties in a series of electrochemical tests.A specific capacitance of 106.3 mAh g^(-1) at 0.2 C is demonstrated,compared to 96.5 mAh g^(-1) for Na_(3)V_(2)(PO_(4))_(3) without hydrothermal treatment,and cycling performance is also improved with 93%capacity retention.The calculated sodium ion diffusion coefficient(DNa=5.68×10^(-14))obtained after EIS curve fitting of the improved sample illustrates that the pore structure is beneficial to the performance of the Na_(3)V_(2)(PO_(4))_(3)cathode material.
文摘通过简单的溶胶-凝胶辅助静电纺丝法得到(113)晶面优势导向的Na_3V_2(PO_4)_3/C钠离子电池正极材料,并通过对比最佳纺丝条件下分别用聚乙烯吡咯烷酮(PVP)和聚氧化乙烯(PEO)作为晶面导向剂制备的两种Na_3V_2(PO_4)_3电极材料的电化学性能,证明静电纺丝有利于实现Na_3V_2(PO_4)_3(113)晶面择优取向。在相同的电流密度(0.1 C)下,NVP-PVP和NVP-PEO的首周放电比容量分别为112.5 m A·h/g和96.3 m A·h/g,电池循环50周后,NVP-PVP仍然有98.1 m A·h/g的可逆容量保持,NVP-PEO仅仅只剩下34 m A·h/g的可逆容量保持,而即使循环100周后,NVP-PVP的可逆容量仍然在88.2 m A·h/g。结果表明,PVP静电纺丝有利于构建特定的纳米纤维结构和均一的导电碳网络骨架,进而提升主体材料Na_3V_2(PO_4)_3的电化学性能。
基金supported by the National Natural Science Foundation of China(61071040)Leading Academic Discipline Project of Shanghai Municipal Education Commission,China(J50102)Research and Innovation Project of Shanghai Municipal Education Commission,China~~
文摘采用溶胶凝胶-高温固相法,用不同的钠源制备NASICON结构钠离子电池正极材料Na_3V_2(PO_4)_3.借助扫描电子显微镜(SEM),X射线衍射分析(XRD),电池测试系统及电化学工作站对制备的Na_3V_2(PO_4)_3结构,形貌,电性能和内阻进行表征.研究结果表明,以Na_2CO_3为钠源合成Na_3V_2(PO_4)_3有更好的颗粒尺寸,形貌结构完整,充放电性能及循环稳定性更好,阻抗也较小;在2.5~4.0 V电压范围内,以0.2C进行充放电,首次放电比容量达到110.8 m Ah/g,50次循环后容量保持率为85.1%.
基金financial support from the National Natural Science Foundation of China (No.21501171,51403209,21406221,51177156/E0712)
文摘Sodium-ion batteries （SIBs） have attracted increasing attention in the past decades, because of high over-all abundance of precursors, their even geographical distribution, and low cost. Na3V2（PO4）3 （NVP）, atypical sodium super ion conductor （NASlCON）-based electrode material, exhibits pronounced structuralstability, exceptionally high ion conductivity, rendering it a most promising electrode for sodium storage.However. the comparatively low electronic conductivity makes the theoretical capacity of NVP cannot befully accessible even at comparatively low rates, presenting a major drawback for further practical ap-plications, especially when high rate capability is especially important. Thus, many endeavors have beenconformed to increase the surface and intrinsic electrical conductivity of NVP by coating the active mate-rials with a conductive carbon layer, downsizing the NVP particles, combining the NVP particle with vari-ous carbon materials and ion doping strategy. In this review, to get a better understanding on the sodiumstorage in NVP, we firstly present 4 distinct crystal structures in the temperature range of-30℃-225℃ namely α-NVP, β-NVP, β′-NVP and γ-NVP. Moreover, we give an overview of recent approaches to en-hance the surface electrical conductivity and intrinsic electrical conductivity of NVP. Finally, some poten-tial applications of NVP such as in all-climate environment and PHEV, EV fields have been prospected.
基金financially supported by the Fundamental Research Funds for Central Universities(Grant No.:XDJK2015B001)
文摘The modification effects of ytterbium(Yb), Na_3PO_4 and Yb + Na_3PO_4 on primary Mg_2Si phase in Mg-4Si alloys were investigated by means of X-ray diffraction(XRD), optical microscopy(OM), scanning electron microscopy(SEM) and energy dispersive spectroscopy(EDS) analysis in this work. The results indicate that the morphology of the primary Mg_2Si phase apparently changes from coarse dendrites to fine dispersive polygonal particles and the mean size decreases from 276.6 μm to 7.1 μm, with combined modification of 0.8wt.% Yb and 2.64 wt.% Na_3PO_4. Such a morphological evolution results in improvement in the ultimate tensile strength and elongation of the alloys as compared to the base alloy. This may be attributed to the formation of the YbP particles that acted as the heterogeneous nucleation substrates for the primary Mg_2Si particles, resulting in a refined distribution of these precipitates. The results of XRD examination show that there was no reaction between Si and Yb or Na_3PO_4. Solo addition of Yb or Na_3PO_4 into the melt has no real modification effect on the microstructure, but the primary Mg_2Si particles and α-Mg phases become coarser than that in the unmodified alloy.
