Analysis of the Carbon Nano-Structures Formation in Liquid Arcing

Graphite electrodes were used for the direct current （DC） arc discharge in water. And high-resolution transmission electron microscopy （HRTEM） was used to investigate the products. Based on the experimental phenomena and nano-structure products, arc plasma characteristics in water were analyzed theoretically. Two growth regions and relevant growth modes were proposed to interpret the formation mechanisms of nano-structures by arc discharge in water. Furthermore, liquid nitrogen and cross magnetic field was applied to change the arcing state respectively, and new carbon nano-structures were obtained. Their formation mechanisms were also analyzed correspondingly.

Self-assembled germanium nano-structures by laser-assisted oxidation

The investigation on the oxidation behaviour of Si1-xGex alloys （x=0.05, 0.15, and 0.25） is carried out. It is found for the first time that on the oxide film a germanium nano-cap with a thickness of 1.8-2.8nm and a few Ge nanoparticles with diameters ranging from 5.5 nm to 10 nm are formed by the low-temperatu.re laser-assisted dry oxidation of Si1-xGex substrate. A new scanning method on the decline cross-section of the multiple-layer sample is adopted to measure the layer thickness and the composition. Some new peaks in photoluminescence （PL） spectra are discovered, which could be related to the nano-cap and the nano-particles of germanium. A suitable model and several new calculating formulae with the unrestricted Hartree-Fock-Roothaan （UHFR） method and quantum confinement analysis are proposed to interpret the PL spectra and the nano-structure mechanism in the oxide.

Pushing the frontiers: Chip-based detection based on micro-and nano-structures

Changes in trace substances in human metabolites, which are related to disease processes and health status, can serve as chemical markers for disease diagnosis and symptom monitoring. Real-time online detection is an inevitable trend for the future of health monitoring, and the construction of chips for detection faces major challenges. The response of sensors often fails to meet the requirements for chipbased detection of trace substances due to the low efficiency of interfacial heterogeneous reactions, necessitating a rational design approach for micro-and nano-structures to improve sensor performance with respect to sensitivity and detection limits. This review focuses on the influence of micro-and nanostructures that used in chip on sensing. Firstly, this review categorizes sensors into chemiresistors, electrochemical sensors, fluorescence sensors, and surface enhanced Raman scattering(SERS) sensors based on their sensing principle, which have significant applications in disease diagnosis. Subsequently, commencing from the application requirements in the field of sensing, this review focuses on the different structures of nanoparticle(NP) assemblies, including wire, layered, core-shell, hollow, concave and deformable structures. These structures change in the size, shape, and morphology of conventional structures to achieve characteristics such as ordered alignment, high specific surface area, space limitation,vertical diffusion, and swaying behavior with fluid, thereby addressing issues such as poor signal transmission efficiency, inadequate adsorption and capture capacity, and slow mass transfer speed during sensing. Finally, the design direction of micro-and nano-structures, and possible obstacles and solutions to promote chip-based detection have been discussed. It is hope that this article will inspire the exploration of interface micro-and nano-structures modulated sensing methods.

Facile synthesis and electrochemical sodium storage of CoS2 micro/nano-structures

We report the synthesis and electrochemical sodium storage of cobalt disulfide （COS2） with various micro/nano-structures. CoS2 with microscale sizes are either assembled by nanoparticles （P-CoS2） via a facile solvothermal route or nano- octahedrons constructed solid （O-COS2） and hollow microstructures （H-CoS2） fabricated by hydrothermal methods. Among three morphologies, H-CoS2 exhibits the largest discharge capacities and best rate performance as anode of sodium-ion batteries （SIBs）. Furthermore, H-CoS2 delivers a capacity of 690 mA.h.g 1 at 1 A·g 1 after 100 cycles in a potential range of 0.1-3.0 V, and N240 mA.h.g-1 over 800 cycles in the potential window of 1.0-3.0 V. This cycling difference mainly lies in the two discharge plateaus observed in 0.1-3.0 V and one discharge plateau in 1.0-3.0 V. To interpret the reactions, X-ray diffraction （XRD） and transmission electron microscopy （TEM） are applied. The results show that at the first plateau around 1.4 V, the insertion reaction （COS2 ＋ xNa＊ ＋ xe NaxCoS2） Occurs; while at the second plateau around 0.6 V, the conversion reaction （NaxCoS2 ＋ （4 - x） Na＋ ＋ （4 - x）e -~ Co ＋ 2Na2S） takes place. This provides insights for electrochemical sodium storage of CoS2 as the anode of SIBs.

Nonswellable hydrogels with robust micro/nano-structures and durable superoleophobic surfaces under seawater

Hydrogels, composed mainly of water trapped in three dimensional cross-linked polymer networks, have been widely utilized to construct underwater superoleophobic surfaces. However, the swelling nature and instability of hydrogels under complex marine environment will weaken their underwater superoleophobicity. Herein, we synthesize structured poly(2-hydroxyethylmethacrylate)(PHEMA) hydrogels by using sandpaper as templates. The robust non-swelling of PHEMA hydrogel ensures that micro/nano-structures on the surface of PHEMA hydrogels can be well maintained. Moreover, when roughness Ra of about 3~4 μm, the surface has superior oil-repellency. Additionally, even after immersing in seawater for one-month, their breaking strength and toughness can be well kept. The non-swellable hydrogels with long-term stable under seawater superoleophobicity will promote the development of robust superoleophobic materials in marine antifouling coatings,biomedical devices and oil/water separation.

Fabrication of micro/nano-structures by electrohydrodynamic jet technique

Electrohydrodynamicjet （E-Jet） is an approach to the fabrication of micro/nano-structures by the use of electrical forces. In this process, the liquid is subjected to electrical and mechanical forces to form a liquid jet, which is further disintegrated into droplets. The major advantage of the E-Jet technique is that the sizes of the jet formed can be at the nanoscale far smaller than the nozzle size, which can realize high printing resolution with less risk of nozzle blockage. The E-Jet technique, which mainly includes E-Jet deposition and E-Jet printing, has a wide range of applications in the fabrication ofmicro/nano-structures for micro/nano-electromechanical system devices. This tech- nique is also considered a micro/nano-fabrication method with a great potential for commercial use. This study mainly reviews the E-Jet deposition/printing fundamentals, fabrication process, and applications.

Engineering nano-structures with controllable dimensional features on micro-topographical titanium surfaces to modulate the activation degree of M1 macrophages and their osteogenic potential

Modulating the activation state and degree of macrophages still remains as a challenge for the topographical design of Ti-based implants.In this work,micro/nano-structured coatings were prepared on Ti substrates by micro-arc oxidation(MAO)and subsequent hydrothermal(HT)treatment.By varying the HT conditions,plate-like nano-structures with an average length of 80,440 or 780 nm were obtained on MAO-prepared micro-topographical surfaces.Depending on the dimensional features of nano-plates,the specimens were noted as Micro,Micro/Nano-180,Micro/Nano-440 and Micro/Nano-780,respectively.The in vitro results showed that the activation state and degree of macrophages could be effectively modulated by the micro/nano-structured surfaces with various dimensional features.Compared to the Micro surface,the Micro/Nano-180 surface activated both M1 and M2 phenotype in macrophages,while the Micro/Nano-440 and Micro/Nano-780 surfaces polarized macrophages to their M1 phenotype.The activation degree of M1 macrophages followed the trend:Micro<Micro/Nano-180<Micro/Nano-440<Micro/Nano-780.However,the osteogenic potential of the activated macrophages in response to various surfaces were in the order:Micro≈Micro/Nano-780<Micro/Nano-180<Micro/Nano-440.Together,the findings presented in this work indicate that engineering nano-structures with controllable dimensional features is a promising strategy to modulate macrophage activation state and degree.In addition,it is essential to determine the appropriate activation degree of M1 macrophages for enhanced osteogenesis.

Osteoblast Behavior on Hierarchical Micro-/Nano-Structured Titanium Surface

In the present work, osteoblast behavior on a hierarchical micro-/nano-structured titanium surface was investigated. A hi- erarchical hybrid micro-/nano-structured titanium surface topography was produced via Electrolytic Etching （EE）. MG-63 cells were cultured on disks for 2 h to 7 days. The osteoblast response to the hierarchical hybrid micro-/nano-structured titanium surface was evaluated through the osteoblast cell morphology, attachment and proliferation. For comparison, MG-63 cells were also cultured on Sandblasted and Acid-etched （SEA） as well as Machined （M） surfaces respectively. The results show signifi- cant differences in the adhesion rates and proliferation levels of MG-63 cells on EE, SLA, and M surfaces. Both adhesion rate and proliferation level on EE surface are higher than those on SLA and M surfaces. Therefore, we may expect that, comparing with SLA and M surfaces, bone growth on EE surface could be accelerated and bone formation could be promoted at an early stage, which could be applied in the clinical practices for immediate and early-stage loadings.

Preparation and Characterization of Nano-Structured SiO_(2) Thin Films on Carbon Steel

Nano-structured SiO2 thin films were prepared on the surface of carbon steel for the first time by LPD. The compositions of the films were analyzed by XPS, and the surface morphology of the thin films were observed by AFM. The thin films were constituted by compact particles of SiO2, and there was no Fe in the films. In the process of film forming, the SiO2 colloid particles were deposited or absorbed directly onto the surface of carbon steel substrates that were activated by acid solution containing inhibitor, and corrosion of the substrates was avoided. The nano-structured SiO2 thin films that were prepared had excellent protective efficiency to the carbon steel.

Electron emission degradation of nano-structured sp^2-bonded amorphous carbon films

The initial field electron emission degradation behaviour of original nano-structured sp^2-bonded amorphous carbon films has been observed, which can be attributed to the increase of the work function of the film in the field emission process analysed using a Fowler-Nordheim plot. The possible reason for the change of work function is suggested to be the desorption of hydrogen from the original hydrogen termination film surface due to field emission current-induced local heating. For the explanation of the emission degradation behaviour of the nano-structured sp2-bonded amorphous carbon film, a cluster model with a series of graphite （0001） basal surfaces has been presented, and the theoretical calculations have been performed to investigate work functions of graphite （0001） surfaces with different hydrogen atom and ion chemisorption sites by using first principles method based on density functional theory-local density approximation.

One-dimensional nano-structure of Cu-Zn-Al alloy

Cu-Zn-Al alloy of one dimensional nano-structure was prepared and thestructure of obtained nano-material was characterized by transmission electron microscope (TEM). Itwas shown that there are non-linear oscillations on the surface of Cu-Zn-Al alloy and theconsanguineous connection exists between non-linear oscillation and the growth process of onedimensional nano-structure. The diameter of one dimensional nano-structure is about 40 nm, and theratio of length to diameter is over 40. Finally, the growth mechanism of one dimensionalnano-structure was also studied.

Nano-Structure Observed in Highly Doped Silicon Crystalline

It was reported that due to the non-linear electrical phenomena,the super-saturated arsenic in silicon single crystalline precipitates during post processing at low temperatures to form different structures.The structure with spatial period of 1.7 to 2.3 nm was observed firstly by TEM on the sample.

Cobalt supported on CNTs-covered γ-and nano-structured alumina catalysts utilized for wax selective Fischer-Tropsch synthesis

Cobalt supported on carbon nanotubes （CNTs）-covered alumina has been recently developed and successfully utilized as a catalyst in Fischer-Tropsch synthesis （FTS）. Problems associated with shaping of Co/CNTs into extrudates or pellets as well as catalyst attrition rendered these materials unfavorable for industrial applications. In this investigation regular γ- and nano-structured （N-S） alumina as well as CNTs-covered regular γ- and N-S-alumina supports were impregnated by cobalt nitrate solution to make new cobalt-based catalysts which were also promoted by Ru. The catalysts were characterized and tested in a micro reactor to evaluate their applicability in FTS. γ-Al2O3 was prepared by calcination of bohemite and N-S-Al2O3 was prepared by sol-gel method using aluminum chloride as starting material. Catalyst evaluations indicated that N-S-Al2O3 was superior to regular γ-Al2O3 and that CNTs-covered alumina supports were favored over non-covered ones in terms of activity and heavy hydrocarbon selectivity. These were justified by porosimetric characteristics of the catalysts and existence of CNTs points of view. CNTs-covered catalysts also showed higher wax selectivity and better resistance to deactivation. Furthermore, TPR analysis indicated that the cobalt aluminate phase, which is responsible for the permanent deactivation of alumina supported Co-based catalysts, did not form on alumina supported Co-based catalysts covered with CNTs due to weaker interactions between cobalt and alumina.

Deposition mechanism of nano-structured single-layered C_(36) film on a diamond (100) crystal plane

The Brenner-LJ potential is adopted to describe the interaction between C36 clusters and diamond surface, and the deposition mechanism of multi-C36 clusters on the diamond surface is also studied by using the method of molecular dynamics simulation. The simulation results show that the competition effects of two interactions, i.e. the interaction between cluster and cluster and the interaction between cluster and crystal plane, are studied, and then the influence of these competition effects on C36 cluster deposition is analysed. The finding is that when an incident energy is appropriately chosen, C36 clusters can be chemically adsorbed and deposited steadily on the diamond surface in the form of single-layer, and in the deposition process the multi-C36 clusters present a phenomenon of energy transmission. The experimental result shows that at a temperature of 300K, in order to deposit C36 clusters into a steady nanostructured single-layered film, the optimal incident energy is between 10 and 18 eV, if the incident energy is larger than 18 eV, the C36 clusters will be deposited into an island nano-structured film.

Research on the field emission mechanism of nano-structured carbon film

The field emission （FE） characteristics of nano-structured carbon films （NSCFs） are investigated. The saturation behaviour of the field emission current density found at high electric field E cannot be reasonably explained by the traditional Fowler-Nordheim （F-N） theory. A three-region E model and the curve-fitting method are utilized for discussing the FE characteristics of NSCFs. In the low, high, and middle E regions, the FE mechanism is reasonably explained by a modified F-N model, a corrected space-charge-limited-current （SCLC） model and the joint model of F N and SCLC mechanism, respectively. Moreover, the measured FE data accord well with the results from our corrected theoretical model.

The 18.3% Silicon Solar Cells with Nano-Structured Surface and Rear Emitter

A nano-structured surface is formed on the pyramid structure of n-type silicon solar cells by size-controlled silver nano-particle assisted etching. Such a nano-structure creates a front average weighted reflectance of less than 2.5% in the 300-1200nm range due to the broadband reflection suppression. The sodium hydroxide is used to obtain the low-area surface by post-etching the nano-structure, thus the severe carrier recombination associated with the nano-structured surface could be reduced. After emitter forming, screen printing and firing by means of the industrial fabrication protocol, an 18.3%-efficient nano-structured silicon solar cell with rear emitter is fabricated. The process of fabricating the solar cells matches well with industrial manufacture and shows promising prospects.

Comparative Assessment on Machinability of Nano-Structured Bainitic Steel and Titanium64

Titanium64 has characteristics well sought after for applications in demanding environments. In general, due to titanium64’s high performance, it is a material which requires careful and well considered machining approaches in order to optimize the process. Nano-structured bainitic steel whilst having different application bases does none the less have similar machining and machinability short comes as that of titanium64. These similar characteristics have been compared and contrasted in this research study using parameters including cutting force, surface texture and metallography. The results tend to indicate that titanium64 has a poorer machinability characteristics compared to nano-structured bainitic steel. However, in terms of achieving greater surface texture characteristics, the nano-structured bainitic steel exhibited an enhanced capacity.

Enhancing Mechanical Stability of Nano-Structured Anti-Reflection Coatings

Periodic Nanostructured anti-reflection coatings (NALs) are a promising option for enhancing transmission of coherent light without inducing scattering. We’ve found that reducing the height of NALs below a critical value to enhance mechanical stability can highly reduce the transmission efficiency. Here, using Rigorous Couples Wave Analysis (RCWA), we find the minimum height for over 99% transmission and effect of height on transmission bandwidth. Then, during a one-step plasma etching, two samples with different heights have been generated and their efficiency is evaluated using RCWA.

A Comparative Study on the Milling Speed for the Synthesis of Nano-Structured Al 6063 Alloy Powder by Mechanical Alloying

The present article reports on characterization studies performed on amorphized nanostructured Al 6063 alloy powder synthesized by mechanical alloying (MA). The as-milled powder was characterized by X-ray diffraction (XRD) for investigating the development of crystallite nature and determining the different phases of the materials present, scanning electron microscope (SEM) was used for in depth morphological study and High Resolution-transmission electron microscope (HR-TEM) was employed to ensure the development of a nano-structured nature of the Al 6063 matrix. In the present work alloyed powder was milled for 20 h and 40 h at 300 rpm;and 20 h at 700 rpm in a hardened stainless steel medium. Using Williamson-Hall equation;crystallite size, lattice strain and lattice parameter of Al 6063 nanostructure alloy powder was estimated with broadening of XRD peaks. XRD results showed that the crystallite size of Al 6063 alloy powder reached 32 and 53 nm after 20 h at 700 rpm and 40 h at 300 rpm respectively.

Preparation and Characterization of Cu-Zn Nano-Structural Ferrite Thin Films Produced by Pulsed Laser Deposition (PLD)

Cu-Zn ferrite nano thin films were deposited from a target of Cu-Zn ferrite onto a sapphire substrate using XeCl excimer laser operating 308 nm with an energy of 225 mJ and a frequency of 30 Hz. Films were deposited from the target onto sapphire (001) substrates heated to 650℃ in an oxygen atmosphere of 100 mTorr. The laser beam was incident On the target face at an angle of 45°. Studies on crystal structure were done by X-ray diffactometry (XRD). The surface texture, cross-section morphology and grain size was observed by JEOL-JSM-6400 scanning electron microscopy, atomic force microscopy (AFM) and magnetic force microscopy (MFM) [Model DI 3000, Digital instruments].