Transmission effects of high energy nanosecond lasers in laser-induced air plasma under different pressures

When a high energy nanosecond(ns)laser induces breakdown in the air,the plasma density generated in the rarefied atmosphere is much smaller than that at normal pressure.It is associated with a relatively lower absorption coefficient and reduces energy loss of the laser beam at low pressure.In this paper,the general transmission characterizations of a Joule level 10 ns 1064 nm focused laser beam are investigated both theoretically and experimentally under different pressures.The evolution of the electron density(n_(e)),the changes in electron temperature(T_(e))and the variation of laser intensity(I)are employed for numerical analyses in the simulation model.For experiments,four optical image transfer systems with focal length(f)of 200 mm are placed in a chamber and employed to focus the laser beam and produce plasmas at the focus.The results suggest that the transmittance increases obviously with the decreasing pressure and the plasma channels on the transmission path can be observed by the self-illumination.The simulation results agree well with the experimental data.The numerical model presents that the maximum n_e at the focus can reach 10^(19)cm^(-3),which is far below the critical density(n_(c)).As a result,the laser beam is not completely shielded by the plasmas.

High-quality micro-shape fabrication of monocrystalline diamond by nanosecond pulsed laser and acid cleaning

The flat plane of small surface roughness below 0.1μm average roughness was obtained for monocrystalline diamond by nanosecond pulsed laser irradiation of 1060 nm and post-process acid cleaning,at a laser fluence around the material removal threshold value.The glossy and flat plane at the bottom of the micro-groove was parallel to the top surface of the specimen,although the round beam of Gaussian mode was irradiated in the direction perpendicular to the top surface of specimen.The square beam of top-hat mode produced a shallower micro-groove with a wider,flatter bottom compared with the round beam in Gaussian mode.The creation method of the flat plane with small surface roughness was discussed in the arrangement strategy of linear micro-grooving by the square beam of top-hat mode.Normal side-by-side repetition of linear micro-grooving did not create a flat plane with constant depth.Therefore,a two-step scanning method was proposed in order to overcome the problem in the normal side-by-side repetition of liner micro-grooving.Non-removal areas were partly retained between the processing lines in the first step,and the laser scanning was conducted on the retained area in the second step.The newly proposed two-step scanning method was practical and useful to create a widely flat plane with small surface roughness,and the two-step scanning method provided superior control over the micro-groove depth.This proposed method can reduce the surface roughness in addition to the shape creation of monocrystalline diamond,and it can be used as a high-quality micro-shape fabrication method of monocrystalline diamond.

2-μm mode-locked nanosecond fiber laser based on MoS_2 saturable absorber

We demonstrated a 2-μm passively mode-locked nanosecond fiber laser based on a MoS2 saturable absorber（SA）.Owing to the effect of nonlinear absorption in the MoS2 SA, the pulse width decreased from 64.7 to 13.8 ns with increasing pump power from 1.10 to 1.45 W. The use of a narrow-bandwidth fiber Bragg grating resulted in a central wavelength and 3-dB spectral bandwidth of 2010.16 and 0.15 nm, respectively. Experimental results show that MoS2 is a promising material for a 2-μm mode-locked fiber laser.

Oxidation mechanism of high-volume fraction SiCp/Al composite under laser irradiation and subsequent machining

Conventional mechanical machining of a composite material comprising an aluminum matrix reinforced with a high volume fraction of SiC particles(hereinafter referred to as an SiCp/Al composite)faces problems such as rapid tool wear,high specific cutting force,and poor surface integrity.Instead,a promising method for solving these problems is laser-induced oxidation-assisted milling(LOAM):under laser irradiation,the local workpiece material reacts with oxygen,thus forming loose and porous oxides that are easily removed.In the present work,the oxidation mechanism of SiCp/Al irradiated by a nanosecond pulsed laser is studied to better understand the laser-induced oxidation behavior and control the characteristics of the oxides,with laser irradiation experiments performed on a 65%SiCp/Al composite with various laser parameters and auxiliary gases(oxygen,nitrogen,and argon).With increasing laser pulse energy density,both the ablated groove depth and the width of the heat-affected zone increase.When oxygen is used as the auxiliary gas,an oxide layer composed of SiO_(2)and Al2O3 forms,and CO_(2)is produced and escapes from the material,thereby forming pores in the oxides.However,when nitrogen or argon is used as the auxiliary gas,a recast layer is produced that is relatively difficult to remove.Under laser irradiation,the sputtered material reacts with oxygen to form oxides on both sides of the ablated groove,and as the laser scanning path advances,the produced oxides accumulate to form an oxide layer.LOAM and conventional milling are compared using the same milling parameters,and LOAM is found to be better for reduced milling force and tool wear and improved machined surface quality.